Iron-enriched natural zeolite modified carbon paste electrode for H2O2 detection

This work demonstrates that iron-enriched natural zeolitic volcanic tuff (Paglisa deposit, Cluj county, Transilvania, Romania) resulting from a previous use as adsorbent in wastewater treatment can be recycled into effective electrode modifier applied to the electrocatalytic detection of hydrogen peroxide. After physico-chemical characterization of tuff samples using various techniques such as chemical analysis, X-ray diffraction, scanning electron microscopy, infrared spectroscopy, BET analysis and X-ray photoelectron spectroscopy, the electrochemical response of the iron-enriched zeolites was studied on the basis of solid carbon paste electrodes modified with these samples. The results indicate that iron centers in the zeolite are electroactive and that they act as electrocatalysts in the voltammetric and amperometric detection of H₂O₂. Best performance was achieved in phosphate buffer at pH 7, showing a sensitivity of 0.57 mA M⁻¹ cm⁻², a detection limit down to 60 μM, and a linear domain up to 100 mM H₂O₂.     

Electrocatalytic reduction of dioxygen on hemin based carbon paste electrode

A hemin-modified carbon paste electrode was constructed by a simple, rapid and effective method. The electrochemical behaviour of the modified electrode was characterized by cyclic voltammetry. The modified electrode obtained was very stable and exhibited electrocatalytic response for the reduction of oxygen. The possible mechanism for the catalytic reduction of dioxygen is discussed. The dioxygen is reduced via a one-step reduction accompanying four electrons and four protons transfer at pH 7–11.     

Electrochemical property of methylene blue redox dye immobilized on porous silica-zirconia-antimonia mixed oxide

The mixed oxide SiO₂/ZrO₂ obtained by the sol-gel processing method adsorbs Sb(V) from acid solution, forming a new phase on the matrix surface designated as SiO₂/ZrO₂/Sb₂O₅. The amount of Zr(IV) in the matrix was 8.1 wt.%, corresponding to 0.89 mmol g⁻¹, and the amount of Sb(V) incorporated in the matrix was 6.3 wt.% (0.52 mmol g⁻¹). This material presented a specific surface area, S_BET=590 m² g⁻¹. The immobilized Sb₂O₅ is a good cation exchanger and adsorbs methylene blue (MB) cationic dye with an average surface density δ=1.1×10⁻¹¹ mol cm⁻² (about 0.07 molecule nm⁻²). The dye is strongly entrapped in the pores of the matrix and it is not leached off in KCl solutions as concentrated as 1.0 M. A carbon paste of the SiO₂/ZrO₂/Sb₂O₅/MB material showed a reversible redox pair with midpoint potential E_m=−0.1 V versus SCE. This midpoint potential is not affected by solution pH change between 2 and 7. The immobilized dye mediated NADH catalytic oxidation at ca. 50 mV.     

A novel non-enzymatic hydrogen peroxide sensor based on single walled carbon nanotubes–manganese complex modified glassy carbon electrode

A simple procedure was developed to prepare a glassy carbon (GC) electrode modified with single wall carbon nanotubes (SWCNTs) and phenazine derivative of Mn-complex. With immersing the GC/CNTs modified electrode into Mn-complex solution for a short period of time 20–100 s, a stable thin layer of the complex was immobilized onto electrode surface. Modified electrode showed a well defined redox couples at wide pH range (1–12). The surface coverages and heterogeneous electron transfer rate constants (k_s) of immobilized Mn-complex were approximately 1.58 × 10⁻¹⁰ mole cm⁻² and 48.84 s⁻¹. The modified electrode showed excellent electrocatalytic activity toward H₂O₂ reduction. Detection limit, sensitivity, linear concentration range and k_cat for H₂O₂ were, 0.2 μM and 692 nA μM⁻¹ cm⁻², 1 μM to 1.5 mM and 7.96(±0.2) × 10³ M⁻¹ s⁻¹, respectively. Compared to other modified electrodes, this electrode has many advantageous such as remarkable catalytic activity, good reproducibility, simple preparation procedure and long term stability.     

碳糊电极和化学修饰碳糊电极制备及应用综述

综述了碳糊电极及化学修饰碳糊电极的发展、制备及表征,概括了近年来化学修饰碳糊电极在食品分析、药物分析、环境监测等领域的应用,并展望了其发展前景。     

Electrochemical sensor array made from bisphthalocyanine modified carbon paste electrodes for discrimination of red wines

A new sensor system devoted to the discrimination of red wines is presented. It consists of an array of electrochemical sensors made from carbon paste electrodes modified with three rare-earth bisphthalocyaninate compounds, including lutetium(III), gadolinium(III) and praseodymium(III) bisphthalocyaninates. The sensor responses have been evaluated either by cyclic voltammetry or by square wave voltammetry, and demonstrate that such voltammetric sensors show a rich response when immersed in red wines. In addition, this response can be tuned by changing the central metal atom of the double-decker complexes, obtaining sensing units with high cross-selectivity.

The sensor array is exposed to six Spanish red wines made from the same grape variety, prepared using a similar vinification method, but belonging to three different geographic origins and ageing stages. The voltammograms indicate that each sensing unit provides a particular response to each class of wine.

Finally, the signals coming from each sensor are combined and the system’s discrimination capability is evaluated by using principal component analysis (PCA), where a windowed slicing pre-processing method has been developed to capture the information throughout the global response. The PCA score plots of the obtained data show the discrimination of the tested wines with a good-quality performance.     

Comparative investigation on electrochemical behavior of hydroquinone at carbon ionic liquid electrode, ionic liquid modified carbon paste electrode and carbon paste electrode

Ionic liquid, 1-heptyl-3-methylimidazolium hexafluorophosphate (HMIMPF₆), has been used to fabricate two new electrodes, carbon ionic liquid electrode (CILE) and ionic liquid modified carbon paste electrode (IL/CPE), using graphite powder mixed with HMIMPF₆ or the mixture of HMIMPF₆/paraffin liquid as the binder, respectively. The electrochemical behaviors of hydroquinone at the CILE, the IL/CPE and the CPE were investigated in phosphate buffer solution. At all these electrodes, hydroquinone showed a pair of redox peaks. The order of the current response and the standard rate constant of hydroquinone at these electrodes were as follows: CILE > IL/CPE > CPE, while the peak-to-peak potential separation was in an opposite sequence: CILE < IL/CPE < CPE. The results show the superiority of CILE to IL/CPE and CPE, and IL/CPE to CPE in terms of promoting electron transfer, improving reversibility and enhancing sensitivity. The CILE was chosen as working electrode to determine hydroquinone by differential pulse voltammetry, which can be used for sensitive, simple and rapid determination of hydroquinone in medicated skin cosmetic cream.     

Hydrogen peroxide sensor based on modified vitreous carbon with multiwall carbon nanotubes and composites of Pt nanoparticles-dopamine

Sensors using nanostructured materials have been under development in the last decade due to their selectivity for the detection and quantification of different compounds. The physical and chemical characteristics of carbon nanotubes provide significant advantages when used as electrodes for electronic devices, fuel cells and electrochemical sensors. This paper presents preliminary results on the modification of vitreous carbon electrodes with Multiwall Carbon Nanotubes (MWCNTs) and composites of Pt nanoparticles-dopamine (DA) as electro-catalytic materials for the hydrogen peroxide (H₂O₂) reaction. Chemical pre-treatment and consequent functionalization of MWCNTs with carboxylic groups was necessary to increase the distribution of the composites. In addition, the presence of DA was important to protect the active sites and eliminate the pasivation of the surface after the electro-oxidation of H₂O₂ takes place. The proposed H₂O₂ sensor exhibited a linear response in the 0-5 mM range, with detection and quantification limits of 0.3441 mM and 1.1472 mM, respectively.     

Formation of a robust and stable film comprising ionic liquid and polyoxometalate on glassy carbon electrode modified with multiwalled carbon nanotubes: Toward sensitive and fast detection of hydrogen peroxide and iodate

A robust and stable film comprising n-octylpyridinum hexafluorophosphate ([C₈Py][PF₆]) and 1:12 phosphomolybdic acid (PMo₁₂) was prepared on glassy carbon electrodes modified with multiwall carbon nanotubes (GCE/MWCNTs) by dip-coating. The cyclic voltammograms of the GCE/MWCNTs/[C₈Py][PF₆]-PMo₁₂ showed three well-defined pairs of redox peaks due to the PMo₁₂ system. The surface coverage for the immobilized PMo₁₂ and the average values of the electron transfer rate constant for three pairs of redox peaks were evaluated. The GCE/MWCNTs/[C₈Py][PF₆]-PMo₁₂ showed great electrocatalytic activity towards the reduction of H₂O₂ and iodate. The kinetic parameters of the catalytic reduction of hydrogen peroxide and iodate at the electrode surface and analytical features of the sensor for amperometric determination of hydrogen peroxide and iodate were evaluated.     

Electrochemical properties of carbide-derived carbon electrodes in non-aqueous electrolytes based on different Li-salts

Electrochemical characteristics of carbide-derived micro/mesoporous carbon material C(TiC) (prepared from TiC) have been studied in 1 M LiClO₄, 0.5 M LiClO₄ + 0.5 M LiPF₆, and 1 M LiPF₆ electrolyte solutions in ethylene carbonate–dimethyl carbonate solvent mixture (1:1 by volume), by using cyclic voltammetry (CV), constant current charge/discharge and electrochemical impedance spectroscopy (EIS). Region of ideal polarizability, values of series capacitance and resistance, charge transfer resistance and capacitance, and other characteristics dependent on the electrolyte anion chemical composition have been established. The dependence of Li⁺ ion intercalation characteristics and solid electrolyte interface (SEI) formation on the salt anion composition have been established and discussed. It was found that the three electrolytes studied are comparatively weak candidates for long-lasting high energy and power density supercapacitors.     

Electrochemical reduction of dilute chromate solutions on carbon felt electrodes

Carbon felt is a potential material for electrochemical reduction of chromates. Very dilute solutions may be efficiently treated due to its large specific surface area and high porosity. In this work, the up-scaling of this technology is investigated using a new type of separated cell and once-through flow of industrial rinse water. A significant enhancement of the process is obtained due to copper deposition during long-term operation. The co-deposition and re-solution of copper occurs depending on the inlet chromate concentration. When previously deposited copper is present a current-free reduction of chromate takes place resulting in current efficiencies apparently above 100%. Very high space time yields are obtained even for effluents at low concentration and optimised conditions (high flow rates and pH 2). The economic feasibility of the technology is also considered. Continuous, single-pass operation results in lower energy requirements than batch processing. The economic potential of the process is also evaluated in comparison with chemical detoxification of chromate. The operating costs for the electrochemical treatment of very dilute effluents on a carbon felt electrode are 30% lower than for the chemical method.     

Amperometric detection of hydrogen peroxide at nano-nickel oxide/thionine and celestine blue nanocomposite-modified glassy carbon electrodes

A simple procedure was developed to prepare a glassy carbon (GC) electrode modified with nickel oxide (NiOx) nanoparticles and water-soluble dyes. By immersing the GC/NiOx modified electrode into thionine (TH) or celestine blue (CB) solutions for a short period of time (5–120 s), a thin film of the proposed molecules was immobilized onto the electrode surface. The modified electrodes showed stable and a well-defined redox couples at a wide pH range (2–12), with surface confined characteristics. In comparison to usual methods for the immobilization of dye molecules, such as electropolymerization or adsorption on the surface of preanodized electrodes, the electrochemical reversibility and stability of these modified electrodes have been improved. The surface coverage and heterogeneous electron transfer rate constants (k_s) of thionin and celestin blue immobilized on a NiOx-GC electrode were approximately 3.5 × 10⁻¹⁰ mol cm⁻², 6.12 s⁻¹, 5.9 × 10⁻¹⁰ mol cm⁻² and 6.58 s⁻¹, respectively. The results clearly show the high loading ability of the NiOx nanoparticles and great facilitation of the electron transfer between the immobilized TH, CB and NiOx nanoparticles. The modified electrodes show excellent electrocatalytic activity toward hydrogen peroxide reduction at a reduced overpotential. The catalytic rate constants for hydrogen peroxide reduction at GC/NiOx/CB and GC/NiOx/TH were 7.96 (±0.2) × 10³ M⁻¹ s⁻¹ and 5.5 (±0.2) × 10³ M⁻¹ s⁻¹, respectively. The detection limit, sensitivity and linear concentration range for hydrogen peroxide detection were 1.67 μM, 4.14 nA μM⁻¹ nA μM⁻¹ and 5 μM to 20 mM, and 0.36 μM, 7.62 nA μM⁻¹, and 1 μM to 10 mM for the GC/NiOx/TH and GC/NiOx/CB modified electrodes, respectively. Compared to other modified electrodes, these modified electrodes have many advantages, such as remarkable catalytic activity, good reproducibility, simple preparation procedures and long-term stabilities of signal responses during hydrogen peroxide reduction.     

Electrochemical behaviour of glassy carbon electrodes modified with aryl groups

The electrochemical modification of the glassy carbon (GC) electrode surface with biphenyl, 1-naphthyl, 2-naphthyl, 4-bromophenyl, 4-decylphenyl and 4-nitrophenyl groups was performed by the diazonium reduction method. The blocking behaviour of aryl films grafted by three different procedures was compared. Oxygen reduction was studied on these modified GC electrodes using the rotating disk electrode (RDE) method. The highest blocking efficiency for O₂ reduction was observed for 4-bromophenyl groups. The barrier properties of aryl-modified GC surfaces were also characterised using Fe(CN)₆³⁻ and dopamine redox probes. Electrochemical measurements were carried out in 0.1 M K₂SO₄ containing 1 mM K₃Fe(CN)₆ and in 0.1 M H₂SO₄ containing 1 mM dopamine using cyclic voltammetry (CV). The blocking action varied significantly depending on the surface modifier used and the solution based redox species studied.     

A hydrogen peroxide sensor based on a horseradish peroxidase/polyaniline/carboxy-functionalized multiwalled carbon nanotube modified gold electrode

We have developed a polyaniline/carboxy-functionalized multiwalled carbon nanotube (PAn/MWCNTCOOH) nanocomposite by blending the emeraldine base form of polyaniline (PAn) and carboxy-functionalized multiwalled carbon nanotubes (MWCNT) in dried dimethyl sulfoxide (DMSO) at room temperature. The conductivity of the resulting PAn/MWCNTCOOH was 3.6 × 10⁻³ S cm⁻¹, mainly as a result of the protonation of the PAn with the carboxyl group and the radical cations of the MWCNT fragments. Horseradish peroxidase (HRP) was immobilized within the PAn/MWCNTCOOH nanocomposite modified Au (PAn/MWCNTCOOH/Au) electrode to form HRP/PAn/MWCNTCOOH/Au for use as a hydrogen peroxide (H₂O₂) sensor. The adsorption between the negatively charged PAn/MWCNTCOOH nanocomposite and the positively charged HRP resulted in a very good sensitivity to H₂O₂ and an increased electrochemically catalytical current during cyclic voltammetry. The HRP/PAn/MWCNTCOOH/Au electrode exhibited a broad linear response range for H₂O₂ concentrations (86 μM–10 mM). This sensor exhibited good sensitivity (194.9 μA mM⁻¹ cm⁻²), a fast response time (2.9 s), and good reproducibility and stability at an applied potential of −0.35 V. The construction of the enzymatic sensor demonstrated the potential application of PAn/MWCNTCOOH nanocomposites for the detection of H₂O₂ with high performance and excellent stability.     

Electrochemical behavior of cysteine at a CuGeO3 nanowires modified glassy carbon electrode

A CuGeO₃ nanowire modified glassy carbon electrode was fabricated and characterized by scanning electron microscopy. The results of electrochemical impedance spectroscopy reveal that electron transfer through nanowire film is facile compared with that of bare glassy carbon electrode. The modified electrode exhibited a novel electrocatalytic behavior to the electrochemical reactions of l-cysteine in neutral solution, which was not reported previously. Two pairs of semi-reversible electrochemical peaks were observed and assigned to the processes of oxidation/reduction and adsorption/desorption of cysteine at the modified electrode, respectively. The electrochemical response of cysteine is poor in alkaline condition and is enhanced greatly in acidic solution, suggesting that hydrogen ions participate in the electrochemical oxidation process of cysteine. The intensities of two anodic peaks varied linearly with the concentration of cysteine in the range of 1 × 10⁻⁶ to 1 × 10⁻³ mol L⁻¹, which make it possible to sensitive detection of cysteine with the CuGeO₃ nanowire modified electrode. Furthermore, the modified electrode exhibited good reproducibility and stability.     

Novel electrode for electrochemical stripping analysis based on carbon paste modified with bismuth powder

Bismuth-powder modified carbon paste electrode (Bi-CPE) is presented as an attractive “mercury-free” sensor applicable in electrochemical striping analysis of selected heavy metals. The electrode paste was prepared as a mixture of finely powdered metallic bismuth together with graphite powder and silicon oil. The Bi-CPE was characterized in nondeaerated solutions containing Cd(II) and Pb(II) at the μg/L level in conjunction with square-wave anodic stripping voltammetry. The electrode exhibited well-defined and separated stripping signals for both metals accompanied with a low background contribution, and a reproducibility of 5.6 and 6.0% (n = 12) for 20 μg/L Cd(II) and Pb(II), respectively. The Bi-CPE exhibited superior performance in comparison to the bare carbon paste electrode (CPE) and the bismuth paste electrode (BiPE) and surprisingly, yielded a higher response than the in situ prepared bismuth-film carbon paste electrode. The electrode displayed excellent linear behavior in the examined concentration range from 10 to 100 μg/L Cd(II) + Pb(II) (R² = 0.998 for both), with limits of detection of 1.2 μg/L for Cd(II) and 0.9 μg/L for Pb(II). The electroanalytical performance of Bi-CPE was successfully tested in a real sample of tap water spiked with Cd(II) and Pb(II).     

Continuous glucose monitoring using enzyme-immobilized platinized diamond microfiber electrodes

A sensitive and stable glucose biosensor for in vivo monitoring has been developed using boron-doped diamond microfiber (BDDMF) electrodes. The electrodes were modified with platinum nano-particles to detect H₂O₂, which was enzymatically produced by glucose oxidase (GOx) immobilized on the electrode surface. The platinum-modified BDDMF (Pt-BDDMF) electrodes exhibited much higher sensitivity compared to Pt-microfiber electrodes, Pt electrodes and Pt-modified diamond thin film electrodes. Deposition conditions for Pt nano-particles on the BDDMF electrodes and immobilization of GOx were optimized. GOx/overoxidized polypyrrole (OPPy)/Pt-modified BDDMF electrodes were applied for continuous interference-free glucose monitoring. Amperometric measurements of glucose showed a linear response in the range of 1-70 mM, with an R.S.D. of 3.7% for five injections of 100 μM glucose. The electrodes exhibited good stability over 3 months with no detected anodic current for ascorbic acid (AA), which is an interfering compound.     

Zinc ion-imprinted polymer based on silica particles modified carbon paste electrodes for highly selective electrochemical determination of zinc ions

ABSTRACT

In this study, Zn(II) ion-imprinted polymer was prepared on the surface of vinyl silica particles and applied for detection of Zn(II) ions using differential pulse voltametry. The ion- imprinted polymer particles were prepared by free radical polymerization. The prepared particles were characterized by different morphological and elemental techniques. The ion-imprinted particles were used to fabricate the carbon paste electrode as a zinc ions sensor. The modified zinc sensor showed linear response in the concentration range 6.12 × 10^?9 to 4.59 × 10^?8 mol L^?1. The limit of detection and limit of quantification of the electrode were 1.351 × 10^?8 and 4.094 × 10^?8 mol L^?1, respectively.     

Studies on the electrochemical behavior of 3-nitrobenzaldehyde thiosemicarbazone at glass carbon electrode modified with nano-γ-Al2O3

Nano-γ-Al₂O₃ is dispersed onto the glass carbon electrode (GCE) by polishing. This nanostructured modified GCE exhibits a great enhancement to the redox responses of 3-nitrobenzaldehyde thiosemicarbazone (3-NBT). In comparison with bare GCE, 3-NBT gives a more sensitive voltammetric response because of the nanoparticle’s unique properties. The lowest detectable concentration (3σ) of 3-NBT is estimated to be 1.18 × 10⁻⁶ M (accumulation for 4 min). The linear relationship between peak current and concentration of 3-NBT holds in the range 1.0 × 10⁻⁵ M to 1.0 × 10⁻⁴ M (r = 0.9981). The electrochemical properties of 3-NBT on this modified electrode have been investigated with various electrochemical methods. The results indicate that the transference of one electron and one proton involves electrode radical reaction processes I and II, respectively. The coverage value (Γ) of 1.62 × 10⁻⁹ mol cm⁻² was calculated and the electrochemical parameters, diffusion coefficient D (2.54 × 10⁻³ cm² s⁻¹, 2.03 × 10⁻³ cm² s⁻¹) and reaction rate constant k_s (5.9573 s⁻¹, 7.15 × 10⁻² cm s⁻¹) were obtained for quasi-reversible system I and irreversible system II, respectively.     

Photocatalysis of methylene blue on titanium dioxide nanoparticles synthesized by modified sol-hydrothermal process of TiCl4

Titanium dioxide nanoparticles were synthesized by the hydrolysis and condensation of TiCl₄, an economic titanium precursor, in a mixed solvent of iso-propyl alcohol and water. As-prepared powders were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FE-SEM), energy filtering transmission electron microscopy (EF-TEM). To examine the photocatalytic activity of the as-prepared TiO₂, the photodegradation of MB which is a typical dye resistant to biodegradation has been investigated on TiO₂ powders in aqueous heterogeneous suspensions. The photocatalytic activity of TiO₂ powders prepared by the hydrolysis of TiCl₄ in the mixed solutions of iso-PrOH/H₂O exceeded that of commercial TiO₂ powders. The apparent first order rate constants (k _app) for the photodegradation of methylene blue (MB) showed a good correlation with the absorbance area obtained by UV-VIS DRS on wavelength in the limits of used lamp emission 300∼420 nm.