Performance analysis of a waste‐heat‐powered thermodynamic cycle for multieffect refrigeration

A multieffect refrigeration system that is based on a waste‐heat‐driven organic Rankine cycle that could produce refrigeration output of different magnitudes at different levels of temperature is presented. The proposed system is integration of combined ejector–absorption refrigeration cycle and ejector expansion Joule–Thomson (EJT) cooling cycle that can meet the requirements of air‐conditioning, refrigeration, and cryogenic cooling simultaneously at the expense of industrial waste heat. The variation of the parameters that affect the system performance such as industrial waste heat temperature, refrigerant turbine inlet pressure, and the evaporator temperature of ejector refrigeration cycle (ERC) and EJT cycles was examined, respectively. It was found that refrigeration output and thermal efficiency of the multieffect cycle decrease considerably with the increase in industrial waste heat temperature, while its exergy efficiency varies marginally. A thermal efficiency value of 22.5% and exergy efficiency value of 8.6% were obtained at an industrial waste heat temperature of 210°C, a turbine inlet pressure of 1.3 MPa, and ejector evaporator temperature of 268 K. Both refrigeration output and thermal efficiency increase with the increase in turbine inlet pressure and ERC evaporator temperature. Change in EJT cycle evaporator temperature shows a little impact on both thermal and exergy efficiency values of the multieffect cycle. Analysis of the results clearly shows that the proposed cycle has an effective potential for cooling production through exploitation of lost energy from the industry. Copyright © 2014 John Wiley & Sons, Ltd.     

Exergy analysis,parametric analysis and optimization for a novel combined power and ejector refrigeration cycle

A new combined power and refrigeration cycle is proposed, which combines the Rankine cycle and the ejector refrigeration cycle. This combined cycle produces both power output and refrigeration output simultaneously. It can be driven by the flue gas of gas turbine or engine, solar energy, geothermal energy and industrial waste heats. An exergy analysis is performed to guide the thermodynamic improvement for this cycle. And a parametric analysis is conducted to evaluate the effects of the key thermodynamic parameters on the performance of the combined cycle. In addition, a parameter optimization is achieved by means of genetic algorithm to reach the maximum exergy efficiency. The results show that the biggest exergy loss due to the irreversibility occurs in heat addition processes, and the ejector causes the next largest exergy loss. It is also shown that the turbine inlet pressure, the turbine back pressure, the condenser temperature and the evaporator temperature have significant effects on the turbine power output, refrigeration output and exergy efficiency of the combined cycle. The optimized exergy efficiency is 27.10% under the given condition.     

Exergy analysis of ejector‐refrigeration cycle using water as working fluid

Exergy is based on the second law of thermodynamics and is the only rational basis for evaluating the system performance. The aim of this paper is to study in detail the irreversibilities in the steam‐ejector refrigeration system. The influence of the cycle parameters is analysed on the basis of the first and second law and the results indicated the components with the greater irreversibility. A better quality of the ejector has more effect on the system performance than the better quality of other components, because the ejector at first and the condenser at second have the greater exergy loss of the system. For the refrigeration system the maximum coefficient of performance varying between 0.4 to 0.6 and the second law efficiency remains close to 0.17 for generator pressure 6 bar, condenser temperature 44–50°C and evaporator temperature 4–8°C. Also the study showed that the second law analysis quantitatively visualizes losses within a system and gives clear trends for optimization. Copyright © 2005 John Wiley & Sons, Ltd.     

A novel solar bi-ejector refrigeration system and the performance of the added injector with different structures and operation parameters

A novel solar bi-ejector refrigeration system was investigated, whose difference compared to the traditional system is that the circulation pump is replaced by a thermal injector. The new system works more stably and needs less maintenance work than the old one, and the whole system can more fully utilize the solar energy. The mathematical models for calculating the performance of the injector and the whole solar refrigeration system were established. The pressure rise performance of injector under different structure and operation parameters and the performance of solar bi-ejector refrigeration system were studied with R123. The results show that the discharged pressure of injector is affected by structure dimensions of injector and operation conditions. With increasing generation temperature, the entrainment ratio of ejector becomes better while that of injector becomes worse and the overall thermal efficiency of the solar bi-ejector refrigeration system first increases and then decreases with an optimum value of 0.132 at generation temperature of 105 °C, condensation temperature of 35 °C and evaporation temperature of 10 °C.     

First and second law investigations of a new solar‐assisted thermodynamic cycle for triple effect refrigeration

This investigation is persuaded for the first and second law analyses of a new solar‐driven triple‐effect refrigeration cycle using Duratherm 600 oil (Duratherm Extended Life Fluid, NY, USA) as the heat transfer fluid is performed. The proposed cycle is an integration of ejector, absorption, and cascaded refrigeration cycles that could produce refrigeration output of different magnitude at different temperature simultaneously. Both exergy destruction and losses in each component and hence in the overall system are determined to identify the causes and locations of the thermodynamic imperfection. The effects of some influenced parameters such as hot oil outlet temperature, refrigerant turbine inlet pressure, and the evaporator temperature of ejector and cascaded refrigeration cycle have been observed on the first and second law performances. It is found that maximum irreversibility occurs in central receiver as 52.5% and the second largest irreversibility of 25% occurs in heliostat field. The second law efficiency of the solar driven triple effect refrigeration cycle is 2%, which is much lower than its first law efficiency of 11.5%. Analysis clearly shows that performance evaluation based on the first law analysis is inadequate and hence, more meaningful evaluation must be included in the second law analysis. Copyright © 2013 John Wiley & Sons, Ltd.     

发生温度对太阳能喷射式制冷系统性能的影响研究

为了确定发生温度对太阳能喷射式制冷系统性能的影响,基于太阳能喷射式制冷系统试验台,以蒸发温度、冷凝温度及室内环境温度为定量,发生温度为变量进行了试验研究.试验结果表明:当喷射器结构确定时,喷射系数ER、系统性能系数COP和机械性能系数COP_m均不会随着发生温度的升高一直增大,系统必然存在一个最佳的发生温度使其性能达到最佳.研究可为今后最佳发生温度的选择及实际应用中如何维持系统高效运行提供理论指导.     

Transient simulation of a solar-based hydrogen production plant with evacuated tube collector and ejector refrigeration system

This article is a careful examination of an energy poly-generation unit integrated with an evacuated solar thermal tube collector. A proton exchange membrane (PEM) electrolysis unit is used for hydrogen production, an ejector refrigeration system (ERS) is utilized for cooling demand, and a heater unit is used for heating demand. All sub-systems are validated by considering recent articles. Cooling and heating demand, as well as the net output power are calculated. The modeled poly-generation system's exergy and energy efficiency are maximized by considering the inlet temperature of the heat exchanger and primary pressure of the ejector with the parametric evaluation of the system. The proposed poly-generation set-up can produce cooling load, heating load, and hydrogen with amounts of 5.34 kW, 5.152 kW, and 63 kg/year, respectively. Based on these values, the energy ef?ciency, and exergy ef?ciency are computed to be 64.14%, and 49.62%, respectively. Higher energy and exergy ef?ciencies are obtained by reducing high pressure of the refrigeration cycle or decreasing the temperature outlet of an auxiliary heater. The heat exchanger and thermal energy storage unit have the highest cost rate among all system components with 73,463 $ and 46,357, respectively. Parametric study indicates that the main determinative elements in the total cost rate of the system are the heater, and the solar collector.     

有机郎肯循环复合系统中喷射器能量分析

有机郎肯循环利用太阳能、地热能和余热驱动,是回收余热、实现能源可持续发展的一个很好途径。有机郎肯循环可与喷射制冷循环结合,可同时提供电能和冷量。喷射器内部流体的不可逆混合引起的能量损失,是该系统最大部分的能量损失。着眼喷射器内部流场分布和机理,分析工作参数和几何参数对其性能的影响,以优化喷射器设计,减小系统能量损失,提高带有喷射器的有机郎肯循环复合系统的效率和节能潜力。结果显示,提高引射压力和出口压力会导致喷射器内部更多能量损失,制约整体系统的性能;在给定工况下,可通过钝化喷嘴内壁面、喷嘴处于最佳位置使喷射器达到最大喷射系数、最优性能,和最小的能量损失。     

太阳能喷射式制冷系统性能分析

叙述了太阳能增压喷射式制冷的原理和系统工作过程. 探讨了太阳能喷射式制冷系统研究的进展状况.通过计算研究了多种制冷剂对喷射器工作性能和系统制冷系数的影响.应用数学模拟的方法,分析了太阳能增压喷射式制冷系统在实际日照条件下的工作性能.结果表明,这种系统能够利用太阳能提供实际需要的制冷量.     

Exergy analysis of Joule–Thomson cryogenic refrigeration cycle with an ejector

In this paper, exergy method is applied to analyze the ejector expansion Joule–Thomson (EJT) cryogenic refrigeration cycle. The exergy destruction rate in each component of the EJT cycle is evaluated in detail. The effect of some main parameters on the exergy destruction and exergetic efficiency of the cycle is also investigated. The most significant exergy destruction rates in the cycle are in the compressor and ejector. The ejector pressure ratio and compressor isothermal efficiency have a significant effect on the exergetic efficiency of the EJT cycle. The exergy analysis results show the EJT cycle has an obvious increase in the exergetic efficiency compared to the basic Joule–Thomson refrigeration cycle. A significant advantage from the use of the ejector is that the total exergy destruction of the EJT cycle can be reduced due to much more decreasing of the exergy destruction rates in the compressor and expansion valve. The exergy analysis also reconfirms that applying an ejector is a very important approach to improve the performance of the Joule–Thomson cryogenic refrigeration cycle.     

基于超临界CO2循环的地热与太阳能混合系统研究

超临界CO₂循环可以耦合较低温度的地热和较高温度的太阳能热组成混合热源发电系统。相比能量分析方法,火用分析方法更便于分析混合系统对提高能量利用率的作用,以及识别造成可用能损失的设备和过程。115℃地热和200℃地热分别与采用槽式聚光集热技术的太阳能热组成混合热源,构成简单回热超临界CO₂循环。分析结果表明：混合系统的火用效率比单纯太阳能热的循环系统提高了5% ~ 10%;太阳能聚光集热器的?损失最大,占80%以上,其次是除预冷器以外的各类换热器以及透平;相比之下,压缩机和预冷器的火用损失较小。减少?损失的关键是提高太阳能聚光集热器和换热器的性能,包括提高集热管运行温度,以及提高换热器效能。     

太阳能喷射式制冷功冷联供系统

以太阳能为驱动热源,基于喷射式制冷和ORC,构建一种太阳能喷射式制冷功冷联供系统,该系统分为太阳能集热子系统和功冷联供子系统两部分。以R161为功冷联供子系统循环工质,通过Matlab建立该系统热力学模型,对其性能进行模拟,在设计工况下该系统制冷量为2.893 kW,净输出功为1.594 kW,功冷联供子系统制冷效率为12.47%,发电效率为6.87%,效率为41.45%。通过分析可知,该系统损占比较大的部件依次为太阳能集热器（73.3%）、发生器（12.14%）、蒸发器（5.03%）和透平（4.81%）。考虑到实际过程,分别研究系统内部参数改变和外部环境参数改变,对系统的影响,发现高低压发生器的温升由利于系统性能的提升,同时环境温度的升高以及太阳辐照度的提升均可改善集热器效率,从而提升系统性能。     

A solar ejector air‐conditioning system using environment‐friendly working fluids

In this paper, the performance of the solar‐driven ejector air conditioning with several environment‐friendly working fluids is studied. The effect of the fluid nature and operating conditions on the ejector performance is examined. This performance is calculated using an empirical correlation. Thermodynamic properties of functioning fluids are obtained with a package REFPROP7. It appears that the refrigerant R717 offers the highest coefficient of performance (COP). For generator temperature T_B = 90°C, condenser temperature T_C = 35°C and evaporator temperature T_E = 15°C and with R717, the COP of ejector air‐conditioning system is 0.408. Using a meteorological data for the city of Tunis, the system performance is computed for three collector types. The air‐conditioning season and period were taken for six months from April to September. The daily period is between 8 and 17 h. For the solar air‐conditioning application, the COP of the overall system varied from 0.21 to 0.28 and the exergy efficiency varied from 0.14 to 0.19 with the same working conditions and total solar radiation (351–875 Wm^?2) in July. Copyright © 2008 John Wiley & Sons, Ltd.     

太阳能喷射式制冷系统的(火用)分析

针对太阳能喷射式制冷系统,利用分析的方法,得到系统各部件的损分布,分析其原因。分别改变发生温度及蒸发温度,探讨了参数变化对系统损的影响。     

First and second law analysis of an ejector expansion Joule–Thomson cryogenic refrigeration cycle

In this paper, a combined first and second law approach is applied to study an ejector expansion Joule–Thomson cryogenic refrigeration cycle. The effects of the evaporator temperature, ejector pressure ratio and compressor function on the coefficient of performance (COP), exergy destruction and the exergetic efficiency have been investigated. The present study has been conducted for the evaporator and compressor temperature in the range of 75–135 and 270–330 K, respectively. The ejector pressure ratio is varied from 1.5 to 5.5. Simulation results show that COP and exergy efficiency increase with increasing evaporator temperature and ejector pressure ratio. In addition, it was found that the increase in the compressor temperature leads to the reduction in the first and second law efficiencies. Copyright © 2010 John Wiley & Sons, Ltd.     

太阳能喷射/压缩复合制冷循环性能研究

研究了一种太阳能喷射/压缩复合制冷循环,由太阳能集热子系统、喷射制冷子系统及压缩制冷子系统组成,系统充分利用热电两种能源以及两种制冷方法各自的优点,优化喷射制冷子系统工作性能的同时,改善压缩式子系统的工作条件,从而提高复合制冷循环性能的同时节约高品位电能。采用性能较好的高蒸发温度式喷射制冷带走压缩机排气余热具有实际意义。通过数值模拟的手段分析系统性能及其主要影响因素,并优化工作条件。研究表明,与相同工作条件下的单压缩制冷循环相比,复合制冷循环工作日全天候运行时电力性能系数提升约为31.5%,节电优势显著。存在一个最佳的喷射子系统蒸发温度使得复合制冷循环性能系数达到运行工况的最大值。     

An exergy analysis of a solar-driven ejector refrigeration system

Exergy analysis is used as a tool to analyse the performance of an ejector refrigeration cycle driven by solar energy. The analysis is based on the following conditions: a solar radiation of 700 W/m², an evaporator temperature of 10 °C, a cooling capacity of 5 kW, butane as the refrigerant in the refrigeration cycle and ambient temperature of 30 °C as the reference temperature. Irreversibilities occur among components and depend on the operating temperatures. The most significant losses in the system are in the solar collector and the ejector. The latter decreases inversely proportional to the evaporation temperature and dominates the total losses within the system. The optimum generating temperature for a specific evaporation temperature is obtained when the total losses in the system are minimized. For the above operating conditions, the optimum generating temperature is about 80 °C.     

A combined power and ejector refrigeration cycle for low temperature heat sources

A combined power and ejector refrigeration cycle for low temperature heat sources is under investigation in this paper. The proposed cycle combines the organic Rankine cycle and the ejector refrigeration cycle. The ejector is driven by the exhausts from the turbine to produce power and refrigeration simultaneously. A simulation was carried out to analyze the cycle performance using R245fa as the working fluid. A thermal efficiency of 34.1%, an effective efficiency of 18.7% and an exergy efficiency of 56.8% can be obtained at a generating temperature of 395 K, a condensing temperature of 298 K and an evaporating temperature of 280 K. Simulation results show that the proposed cycle has a big potential to produce refrigeration and most exergy losses take place in the ejector.     

A novel approach to improve the performance of solar-driven Stirling engine using solar-driven ejector cooling cycle

In this paper, a novel system to enhance the performance of a solar-driven finite speed alpha-type Stirling engine is proposed and evaluated. Part of the concentrated solar energy is used to drive an ejector refrigeration system. The cooling produced in the ejector cooling cycle is used to cool the Stirling engine to enhance its efficiency. Model equations to describe the systems are proposed and solved numerically. The results indicate that the new system produces averagely 3.3 times electrical power more than the conventional one. Moreover, the proposed system improves the Stirling engine efficiency by up to 46% in comparison with 19.15% for the conventional Stirling engine under solar radiation intensity of (1 kW/m²). Also, the results showed that the solar radiation intensity and wind speed are the most influential parameters that affect the proposed system efficiency. The new system is recommended to use in desert climates where high average daily solar radiation intensity, low wind speeds, and water shortage exist. Economic analysis is carried out to determine the feasibility of the proposed system under different economic parameters. It is found that, for instance, the simple payback period is 4.64 years for the new system when the selling price of electricity is 0.35 $/kWh.     

CFD modelling and experimental investigation of an ejector refrigeration system using methanol as the working fluid

This paper presents results of computational fluid dynamic (CFD) analysis and experimental investigation of an ejector refrigeration system using methanol as the working fluid. The CFD modelling was used to investigate the effect of the relative position of the primary nozzle exit within the mixing chamber on the performance of the ejector. The results of the CFD were used to obtain the optimum geometry of the ejector, which was then used to design, construct and test a small‐scale experimental ejector refrigeration system. Methanol was used as the working fluid, as it has the advantage of being an ‘environmentally friendly’ refrigerant that does not contribute to global warming and ozone layer depletion. In addition, use of methanol allows the ejector refrigeration system to produce cooling at temperatures below the freezing point of the water, which of course would not be possible with a water ejector refrigeration system. CFD results showed that positioning the nozzle exit at least 0.21 length of the mixing chamber throat's diameter upstream of the entrance of the mixing chamber gave better performance than pushing it into the mixing chamber. Experimental values of coefficient of performance (COP) between 0.2 and 0.4 were obtained at operating conditions achievable using low‐grade heat such as solar energy and waste heat. Copyright © 2001 John Wiley & Sons, Ltd.