BaFe<Subscript>12</Subscript>O<Subscript>19</Subscript> films produced from BaFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> heterostructures

BaFe₁₂O₁₉ hexaferrite films have been produced on thermally oxidized single-crystal silicon (SiO₂/Si) substrates by sequential ion-beam sputtering of BaFe₂O₄ and α-Fe₂O₃ targets in an argon-oxygen atmosphere. Their crystal structure has been studied, and the origin of the impurity phases forming during heat treatment has been identified. The results show that heat treatment may lead to the formation of eutectic melts. As a result, the hexaferrite films may contain spherulites.     

Kinetics of Thermal Transformation of Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> · 8H<Subscript>2</Subscript>O to Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

The kinetics of thermal dehydration of Mg₃(PO₄)₂ · 8H₂O was investigated using thermogravimetry at four different heating rates. The activation energies of the dehydration step of Mg₃(PO₄)₂ · 8H₂O were calculated through the isoconversional Ozawa and Kissinger-Akahira-Sunose (KAS) methods and iterative methods, which were found to be consistent and indicate a single mechanism. The possible conversion function of the dehydration reaction for Mg₃(PO₄)₂ · 8H₂O has been estimated through the Coats and Redfern integral equation, and a better kinetic model such as random nucleation of the “Avrami–Erofeev equation (A _3/2 model)” was found. The thermodynamic functions (ΔH*, ΔG*, and ΔS*) of the dehydration reaction are calculated by the activated complex theory and indicate that it is a non-spontaneous process when the introduction of heat is not connected.     

Variable—Range hopping in Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-K<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript> glasses

The dc conductivity of the glasses in the Fe₂O₃-Bi₂O₃-K₂B₄O₇ system was studied at temperatures between 223 and 393 K. At temperatures from 300 to 223 K, T^–1/4 (T is temperature) dependence of the conductivity was found, however, both Mott variable-range hopping and Greaves intermediate range hopping models are found to be applicable. Mott and Greaves parameters analysis gave the density of states at Fermi level N (E_F) = 3.13 × 10²⁰–21.01 × 10²⁰ and 1.93 × 10²¹–16.39 × 10²¹ cm^–3eV^–1 at 240 K, respectively. The variable-range hopping conduction occurred in the temperature range T = 300–223 K, since W_D was found to be large (W_D = 0.08–0.14 eV for these glasses) and dominated the conduction at T < 300 K.     

Phase equilibria in the system “CaAl<Subscript>2</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript>”-Na<Subscript>2</Subscript>Al<Subscript>2</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript>-H<Subscript>2</Subscript>O

The phase equilibria in the “CaAl₂Si₃O₁₀”-Na₂Al₂Si₃O₁₀-H₂O system are analyzed using structural and thermal analysis data, and the ideal gonnardite structure is modeled. The results suggest that, to ensure a better correlation with the structures of the zeolites in this series, a new structural model of the gonnardite-based solid solution must be selected, with the structure rotated through 45° about the c axis in the ab plane.     

Phase equilibria in the Tl<Subscript>5</Subscript>Te<Subscript>3</Subscript>–Tl<Subscript>9</Subscript>BiTe<Subscript>6</Subscript>–Tl<Subscript>9</Subscript>TbTe<Subscript>6</Subscript> system

Phase equilibria in the Tl₅Te₃–Tl₉BiTe₆–Tl₉TbTe₆ system have been studied using differential thermal analysis, X-ray diffraction, and microhardness measurements. We have mapped out a number of vertical sections, the 760-K isothermal section of its phase diagram, and projections of its liquidus and solidus surfaces. The composition dependences of lattice parameters and microhardness have been obtained. The system has been shown to contain a continuous series of solid solutions, which crystallize in a tetragonal structure (Tl₅Te₃ type, sp. gr. I4/mcm).     

Enhanced microwave dielectric properties of Ba<Subscript>0.40</Subscript>Sr<Subscript>0.60</Subscript>TiO<Subscript>3</Subscript>–Zr<Subscript>0.80</Subscript>Sn<Subscript>0.20</Subscript>TiO<Subscript>4</Subscript> composite ceramics

The (1−x) Ba_0.40Sr_0.60TiO₃ (BST)−xZr_0.80Sn_0.20TiO₄ (ZST) composite ceramics with x = 10, 20, 30, and 40 wt% were fabricated by conventional solid-state reaction method. With increasing of ZST content, the dielectric constant of composite ceramics was decreased and dielectric loss increases. The effect of ZnO addition to 70 wt% BST–30 wt% ZST composition on the microstructure and dielectric properties was investigated. The improvements in dielectric constant, dielectric loss, and microwave dielectric properties of composite ceramics can be achieved by ZnO addition. The sample with 98 wt% (70 wt% BST–30 wt% ZST)–2 wt%ZnO composition exhibits promising dielectric properties, with dielectric constant, loss tangent and tunability at 4 kV/mm, of 125, 0.0016 and 12%, at 10 kHz and room temperature. At ~2 GHz, it possesses a dielectric constant of 101 and a Q factor of 187, which makes it a good candidate for tunable microwave device applications.     

Microwave dielectric properties of temperature-stable (Mg<Subscript>0.95</Subscript>Co<Subscript>0.05</Subscript>)<Subscript>2</Subscript>TiO<Subscript>4</Subscript>–Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite ceramics for LTCC applications

In this paper, the effects of Li₂O–B₂O₃–Bi₂O₃–SiO₂ (LBBS) glass on the phase formation, sintering characteristic, the microstructure and microwave dielectric properties of temperature-stable (Mg_0.95Co_0.05)₂TiO₄–Li₂TiO₃ ceramics were investigated. (Mg_0.95Co_0.05)₂TiO₄–Li₂TiO₃ powders were obtained by using the traditional solid-state process. A small amount of LBBS doping can effectively reduce sintering temperature and promote the densification of the ceramics. X-ray diffraction analysis revealed not only the primary phase (Mg·Co)₂TiO₄ associated with Li₂TiO₃ minor phase but also a third phase (Mg·Co)TiO₃. The dielectric constant and Qf values vary with the doping amount of LBBS and sintering temperatures. With the compensation of the positive temperature coefficient (τ _f ) of Li₂TiO₃ and the negative τ _f of (Mg_0.95Co_0.05)₂TiO₄, the τ _f of the specimens fluctuates around zero. The (Mg_0.95Co_0.05)₂TiO₄ ceramic with 2.5 wt% LBBS addition and sintering at 900?°C for 4 h exhibited excellent microwave dielectric properties: ? _r ?=?19.076, Qf?=?126100 GHz, and τ _f ?=?0.98 ppm/°C.     

Investigation of solid solution of ZrP<Subscript>2</Subscript>O<Subscript>7</Subscript>–Sr<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

In this study, ZrP₂O₇ was synthesized by the solid state reaction of ZrO₂ and NH₄H₂PO₄ at 900 °C. Then, in set 1; 10, 5, 1, 0.5, 0.1, 0.05, 0.03% previously prepared Sr₂P₂O₇ were doped into ZrP₂O₇, and Sr₂P₂O₇ slightly affect the unit cell parameter of cubic ZrP₂O₇ (a = 8.248(6)–8.233(8) Å). The reverse of this process was also applied to Sr₂P₂O₇ system (set 2). ZrP₂O₇ changes the unit cell parameters of orthorhombic Sr₂P₂O₇ in between a = 8.909(5)–8.877(5) Å, b = 13.163(3)–13.12(1) Å, and c = 5.403(2)–5.386(4) Å. Analysis of the vibrations of the P₂O ₇ ^4? ion and approximate band assignments for IR and Raman spectra are also reported in this work. Some coincidences in infrared and Raman spectra both sets were found and strong P–O–P bands were observed. Surface morphology, EDX analysis, and thermoluminescence properties of both sets were given the first time in this paper.     

Crystal structure of a Np(V) sesquioxalate,Na<Subscript>4</Subscript>(NpO<Subscript>2</Subscript>)<Subscript>2</Subscript>(C<Subscript>2</Subscript>O<Subscript>4</Subscript>)<Subscript>3</Subscript>·2H<Subscript>2</Subscript>O

The crystal structure of a previously unknown Np(V) sesquioxalate, Na₄(NpO₂)₂(C₂O₄)₃·2H₂O was studied. The crystal structure consists of neptunyl(V) cations, sodium cations, oxalate anions, and water molecules of crystallization. Neptunyl(V) cations and oxalate ions form anionic chains [(NpO₂)₂(C₂O₄)₃] _n ^4n? . The coordination polyhedron (CP) of Np (pentagonal bipyramid) contains two apical “yl” oxygen atoms and five equatorial O atoms of three oxalate ions. The CP of Na(1) and Na(2) cations are combined through the common edges into zigzag chains in the [010] direction. Two independent oxalate ions are tridentate and tetradentate ligands.     

System ZnO ⋅ B<Subscript>2</Subscript>O<Subscript>3</Subscript>-CuO ⋅ B<Subscript>2</Subscript>O<Subscript>3</Subscript>

Differential thermal analysis and x-ray diffraction data indicate that the ZnO B₂O₃-CuO B₂O₃ join of the ternary system CuO-B₂O₃-ZnO is pseudobinary, with eutectic phase relations and a liquid-liquid miscibility gap in the composition range 25–35 mol % CuO.Translated from Neorganicheskie Materialy, Vol. 41, No. 3, 2005, pp. 339–340.Original Russian Text Copyright © 2005 by Kasumova, Bananyarly.This revised version was published online in April 2005 with a corrected cover date.This revised version was published online in April 2005 with a corrected cover date.     

New NTC thermistors based on LaCrO<Subscript>3</Subscript>–Mg(Al<Subscript>0.7</Subscript>Cr<Subscript>0.3</Subscript>)<Subscript>2</Subscript>O<Subscript>4</Subscript> composite ceramics

In this study, the xLaCrO₃–(1?x)Mg(Al_0.7Cr_0.3)₂O₄ (x?=?0.1, 0.2, 0.3, 0.4) negative temperature coefficient composite ceramics were fabricated through conventional solid state reaction at 1650?°C. X-ray diffraction analysis has revealed that the sintered ceramics are consisted of cubic spinel Mg(Al_0.7Cr_0.3)₂O₄ phase and orthorhombic perovskite LaCrO₃ phase. The obtained values of \({{\rho }_{\text{300}}}\) and \({{B}_{400/800}}\) and \({{E}_{\text{a}}}\) are in the range of 1.55?×?10²–1.41?×?10⁸ Ωcm, 756–11317 K, 0.065–0.976 eV, respectively. The electrical properties of these ceramics can be adjusted by the LaCrO₃ contents. Such ceramics could be suitable for high temperature NTC thermistor application.     

AC Losses in YBCO-Added Bi<Subscript>1.6</Subscript>Pb<Subscript>0.4</Subscript>Sr<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript><Emphasis Type="Italic">δ</Emphasis></Subscript> Superconductors

The effect of YBCO adding on the superconducting of BPSCCO system with nominal starting composition of (Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O _δ )_1?x(YBCO) _x with x = 0.00?0.10 was studied. The preparation methods used to prepare the samples are the conventional solid-state techniques. From the XRD data, it is observed that the percentage of the Bi-2223 phase increases and Bi-2212 decreases for addition x = 0.02–0.04, respectively. The effect of YBCO addition on the BPSCCO system also has been investigated in term of AC susceptibility study. We have studied the various applied field dependence of the AC susceptibility in polycrystalline samples. The AC susceptibility measurements in the range 0.05 to 2.00 Oe show that as the applied fields increases, the intergranular AC loss peaks move to lower temperature, and also height decreases and width increases. The effect of YBCO addition for the intergranular critical current J _cm, and the presence of weak links that coupled the superconducting grains were defined.     

Phase equilibria in the Tl<Subscript>2</Subscript>Te–Tl<Subscript>5</Subscript>Te<Subscript>3</Subscript>–Tl<Subscript>9</Subscript>TbTe<Subscript>6</Subscript> system

The Tl₂Te–Tl₅Te₃–Tl₉TbTe₆ system has been studied using differential thermal analysis, X-ray diffraction, and microhardness measurements. We have mapped out a number of vertical sections, the 680 K isothermal section of its phase diagram, and projections of its polythermal projections of its liquidus and solidus surfaces. The field of solid solutions with the Tl₅Te₃ structure (δ-phase) has been shown to account for more than 90% of the area of the composition triangle. Tl₂Te-based solid solutions (α-phase) exist in a narrow composition region.     

Growth and structure of Mg(Fe<Subscript>0.8</Subscript>Ga<Subscript>0.2</Subscript>)<Subscript>2</Subscript>O<Subscript>4 − δ</Subscript> films

Films 150–200 nm in thickness, with the nominal composition Mg(Fe_0.8Ga_0.2)₂O_{4 − δ} have been grown on (100) single-crystal silicon substrates by ion-beam sputtering in vacuum. The effect of growth and annealing conditions on the crystal structure and morphology of the films has been studied, and the thermal conditions for the growth of spinel-structure films have been optimized.     

Dual relaxation behaviors and large electrostrictive properties of Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>–Sr<Subscript>0.85</Subscript>Bi<Subscript>0.1</Subscript>TiO<Subscript>3</Subscript> ceramics

Lead-free ceramics (1???x)Bi_0.5Na_0.5TiO₃–xSr_0.85Bi_0.1TiO₃ (BNT–xSBT, x?=?0.4, 0.5, 0.6 and 0.7) were prepared by a solid-state reaction process. Coexistence of ferroelectric relaxation at low temperature and Maxwell–Wagner dielectric relaxation at high temperature was revealed for the first time in this system. Meanwhile, hysteresis-free P–E loops combined with a very high piezoelectric strain coefficient (d₃₃) of 1658 pC/N concurrently with large electrostrictive coefficient Q?=?0.287 m⁴C^?2 were achieved. The ferroelectric relaxor behavior and large electrostrictive strain might be linked to easy reorientation and reversal of ergodic PNRs and the combined effect of Bi off-center position and lone pair electrons.     

Spectroscopic characterisation of local structure in Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses doped with gadolinium

Gadolinium doped bismuth borate glasses containing up to 30 mol% Y₂O₃ were prepared by fast melt quenching method. The effect of yttrium on the local order in 3B₂O₃ · Bi₂O₃ and B₂O₃ · Bi₂O₃ glass matrices, particularly on the bismuth sites, was investigated by infrared (IR) spectroscopy and electron paramagnetic resonance (EPR) of Gd³⁺ ions. The IR results show that the local structure is more ordered in the glass system with higher bismuth content and the progressive addition of yttrium increases the local disorder in both bismuth–borate glass matrices. The EPR results indicate that Gd³⁺ ions occupy both bismuth and yttrium sites and reflect the same structural disorder like that suggested by IR results.     

Crystallization and microstructural evolution of MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript>–La<Subscript>2</Subscript>O<Subscript>3</Subscript> glass-ceramics

Crystallization and microstructure of glasses with the molar compositions 1MgO·1.2Al₂O₃·2.8SiO₂·1.2TiO₂·xLa₂O₃ (x = 0.1 and 0.4) were thermally treated at different temperatures in the range from 950 to 1250 °C and then analyzed by X-ray diffraction and scanning electron microscopy, in combination with energy-dispersive X-ray spectroscopy and electron backscatter diffraction. It was found that the microstructure is first homogeneous with the precipitation of randomly distributed crystals and then indialite domains with embedded perrierite and rutile crystals are formed. For higher temperatures or prolonged times, more domains appear and expand into the bulk of the sample. Finally, the entire sample consists of the indialite domains and the boundaries that are enriched in rutile, perrierite, and magnesium aluminotitanate. Nevertheless, very distinct differences are observed between the samples with different La₂O₃ concentrations. For the sample with x = 0.4, the domains were detected at lower temperatures, while the quantity and size of the domains increase faster due to the promoted precipitation of indialite. For the sample with x = 0.1, in addition to the domain boundaries, secondary boundaries between the “regions” (assemblages of the domains) are observed in a larger length scale. The average size of the crystalline phases found between the “regions” is larger than that typically observed at the domain boundaries. The sizes of the crystals at the boundaries decrease with higher concentrations of La₂O₃, and the crystals (especially perrierite) within the domains become larger, resulting in a more homogeneous microstructure. This results in better dielectric properties, i.e., much higher quality factor for the sample with x = 0.4 in comparison to that with x = 0.1 after heat-treatment at 1150 or 1250 °C.     

Phase relations in the K<Subscript>2</Subscript>MoO<Subscript>4</Subscript>–Ln<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>–Zr(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript> (Ln = La–Lu,Y) systems

We have studied phase relations in the K₂MoO₄–Ln₂(MoO₄)₃–Zr(MoO₄)₂ (Ln = La–Lu, Y) systems by the method of “intersecting cuts,” identified pseudobinary joins in their composition triangles, and constructed their phase compatibility diagrams. The systems have been shown to contain new ternary molybdates with the general formula K₅LnZr(MoO₄)₆ (Ln = Dy–Lu and Y). The thermal characteristics of the synthesized compounds have been studied by differential scanning calorimetry in the temperature range 25–700°C. The new ternary molybdates crystallize in a trigonal structure (sp. gr. R\(\bar 3\)c, Z = 6).     

Preparation and properties of Bi<Subscript>6</Subscript>Ti<Subscript>5</Subscript>WO<Subscript>22</Subscript>: a new phase in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> system

In a recent report, the evaluation of the phase relations in the Bi₂O₃–TiO₂–WO₃ ternary system has shown the existence of a new phase with nominal composition close to Bi₆Ti₅WO₂₂. In the present contribution we attempt to prepare this single phase by using a solid state route. Although XRD analyses also show traces of two minority Aurivillius-type phases in the synthesized materials, the crystal structure of the Bi₆Ti₅WO₂₂ phase has been determined by Rietveld analyses revealing a complex structure similar to that of Bi₃(AlSb₂)O₁₁ and PbHoAl₃O₈ related compounds. The electrical response of this new phase was characterized as well. Three peaks are observed in its dielectric response: two of them positioned around 0 °C and can be assigned to this Bi₆Ti₅WO₂₂ structure. The third one rises up to 665 °C and confirms the presence of the Aurivillius-type phases.     

Evaluation of CaO–SiO<Subscript>2</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–Na<Subscript>2</Subscript>O–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> bioglass-ceramics for hyperthermia application

Magnetic bioglass ceramics (MBC) are being considered for use as thermoseeds in hyperthermia treatment of cancer. While the bioactivity in MBCs is attributed to the formation of the bone minerals such as crystalline apatite, wollastonite, etc. in a physiological environment, the magnetic property arises from the magnetite [Fe₃O₄] present in these implant materials. A new set of bioglasses with compositions 41CaO · (52 ? x)SiO₂ · 4P₂O₅  · xFe₂O₃ · 3Na₂O (2 ≤ x ≤ 10 mol% Fe₂O₃) have been prepared by melt quenching method. The as-quenched glasses were then heat treated at 1050°C for 3 h to obtain the glass-ceramics. The structure and microstructure of the samples were characterized using X-ray diffraction and microscopy techniques. X-ray diffraction data revealed the presence of magnetite in the heat treated samples with x ≥ 2 mol% Fe₂O₃. Room temperature magnetic property of the heat treated samples was investigated using a Vibrating Sample Magnetometer. Field scans up to 20 kOe revealed that the glass ceramic samples had a high saturation magnetization and low coercivity. Room temperature hysteresis cycles were also recorded at 500 Oe to ascertain the magnetic properties at clinically amenable field strengths. The area under the magnetic hysteresis loop is a measure of the heat generated by the MBC. The coercivity of the samples is another important factor for hyperthermia applications. The area under the loop increases with an increase in Fe₂O₃ molar concentration and the. coercivity decreases with an increase in Fe₂O₃ molar concentration The evolution of magnetic properties in these MBCs as a function of Fe₂O₃ molar concentration is discussed and correlated with the amount of magnetite present in them.