Effects of base layer thickness on reliability of CVD Si3N4 stack gate dielectrics

Effects of the base layer in Si₃N₄/SiON stack gate dielectrics, in particular, the physical thickness of the base layer, on the dielectric reliability, MOSFET performance and process controllability are investigated. It is found that the electrical characteristics such as TDDB lifetime as well as the Si₃N₄ film property in Si₃N₄/SiON stack dielectrics with the same capacitance oxide equivalent thickness strongly depend on the SiON-base layer thickness. From the TDDB measurements for both stress polarities and from the Si₃N₄ stoichiometry by the X-ray photoelectron spectroscopy analysis, the optimum SiON-base layer thickness is determined to be approximately 1 nm, in order to obtain longer TDDB lifetime and surperior n-ch MOSFET performance. The obtained results are considered to attribute to the nitrogen profile in the Si₃N₄/SiON stack dielectrics and the strained layer thickness near SiON/Si interface.     

Thermal stability of Hfl'aON films prepared by physical vapor deposition

We investigate the thermal stability of HfTaON films prepared by physical vapor deposition using high resolution transmission electronic microscope (HRTEM) and X-ray photoelectron spectroscopy (XPS). The results indicate that the magnetron-sputtered HtTaON films on Si substrate are not stable during the post-deposition an-healing (PDA). HfTaON will react with Si and form the interfacial layer at the interface between HfTaON and Si substrate. Hf-N bonds are not stale at high temperature and easily replaced by oxygen, resulting in significant loss of nitrogen from the bulk film. SiO2 buffer layer introduction at the interface of HfTaON and Si substrate may effec-tively suppress their reaction and control the formation of thicker interfacial layer. But SiO2 is a low k gate dielectric and too thicker SiO2 buffer layer will increase the gate dielectric's equivalent oxide thickness. SiON prepared by oxidation of N-implanted Si substrate has thinner physical thickness than SiO2 and is helpful to reduce the gate dielectric's equivalent oxide thickness.     

Evidence for bulk trap generation during NBTI phenomenon in pMOSFETs with ultrathin SiON gate dielectrics

Negative bias temperature instability (NBTI) of pMOSFETs with direct-tunneling SiON gate dielectrics was studied in detail. By investigating the effects of applying positive gate bias on pMOSFETs after exposure to NBT stress, the generation of bulk charge traps in the gate dielectrics during NBTI was clearly demonstrated. In particular, it was found that a positive charge generated by negative bias temperature stress (NBT stress) can be neutralized and that the neutralized site can return to the positive state. We consider that the bulk trap is due to hydrogen atoms released from the interface between the SiON gate dielectric and the Si substrate (and this is what has conventionally been considered a positive fixed charge). Moreover, the bulk trap generation was shown to give rise to stress-induced leakage current.     

Demonstration of Low Vt Ni-FUSI N-MOSFETs With SiON Dielectrics by Using a Dy2O3 Cap Layer

This letter reports a novel approach to achieve low threshold voltage (Vt) Ni-fully-silicide (FUSI) nMOSFETs with SiON dielectrics. By using a dysprosium-oxide (Dy₂O₃) cap layer with a thickness of 5 Aring on top of the SiON host dielectrics, V_t,lin of 0.18 V for long-channel devices (L_g = 1 mum) using NiSi-FUSI electrode is obtained, satisfying the high-performance device requirements. The Vt modulation due to the Dy₂O₃ cap layer is also maintained in the short-channel devices (with an L_g,min of 90 nm as demonstrated in this letter). In particular, approximately 150times reduction in gate leakage current is seen while preserving the dielectric capacitance equivalent thickness after adding the Dy₂O₃ cap layer on SiON dielectrics, likely due to a high-k layer (DySiON) formation during device source/drain activation process. We also report that the Dy₂O₃ layer does not vitally degrade the device reliability, such as positive-bias temperature instability and time-dependant dielectrics breakdown.     

1.6 nm oxide equivalent gate dielectrics using nitride/oxide (N/O)composites prepared by RPECVD/oxidation process

Ultrathin nitride/oxide (~1.5/0.7 nm) dual layer gate dielectrics have been formed using remote plasma enhanced CVD of nitride onto plasma-grown oxide interface layers. High accumulation capacitance (1.72 μF/cm²) is measured and the equivalent oxide thickness is 1.6 nm after quantum effect corrections. Compared to 1.6 nm oxides, a tunneling current reduction of more than 100 fold is found for devices with 1.6 nm N/O dielectrics due to increased film thickness and interface nitridation. Hole channel mobility decreases by about 5%, yielding very good P-MOSFET current drive. Excellent dielectric reliability and interface robustness are also demonstrated for P-MOSFET's with N/O dielectrics     

Electrical properties of 1.5-nm SiON gate-dielectric using radical oxygen and radical nitrogen

We have developed a low-leakage and highly reliable 1.5-nm SiON gate-dielectric by using radical oxygen and nitrogen. In this development, we introduce a new method for determining an ultrathin SiON gate-dielectric thickness based on the threshold voltage dependence on the substrate bias in MOSFETs. It was found that oxidation using radical oxygen followed by nitridation using radical nitrogen provides the 1.5-nm (oxide equivalent thickness) SiON, in which leakage current is two orders of magnitude less than that of 1.5-nm SiO/sub 2/ without degrading device performance in NMOSFETs. The 1.5-nm (oxide equivalent thickness) SiON was also found to be ten times more reliable than 1.5-nm SiO/sub 2/.     

High-k Al/sub 2/O/sub 3/ gate dielectrics prepared by oxidation of aluminum film in nitric acid followed by high-temperature annealing

A simple, cost-effective, and room temperature process was proposed to prepare high-k gate dielectrics. An aluminum oxide (Al/sub 2/O/sub 3/) gate dielectric was prepared by oxidation of ultrathin Al film in nitric acid (HNO/sub 3/) at room temperature then followed by high-temperature annealing in O/sub 2/ or N/sub 2/. The substrate injection current behavior and interface trap-induced capacitance were introduced to investigate the interfacial property between the gate dielectric and Si substrate. Al/sub 2/O/sub 3/ gate dielectric MOS capacitors with and without initial SiO/sub 2/ layers were characterized. It was shown that the Al/sub 2/O/sub 3/ gate dielectrics with initial oxide exhibit better electrical properties than those without. The 650/spl deg/C N/sub 2/-POA Al/sub 2/O/sub 3/-SiO/sub 2/ sample with an equivalent oxide thickness of 18 /spl Aring/ exhibits three orders of magnitude reduction in gate leakage current in comparison with the conventional thermal SiO/sub 2/ sample.     

Performance of current mirror with high-k gate dielectrics

This work compares the performance of the basic current mirror topology by using two different materials for gate dielectrics, the conventional SiON and an Hf-based high-k dielectrics. The impact of gate leakage and of channel length modulation on the basic current mirror operation is described. It is shown that in the case of SiON gate dielectrics with an equivalent oxide thickness (EOT) of 1.4 nm, it is not possible to find a value for the channel length which allows a good trade-off to be obtained while minimizing the gate leakage and reducing the channel length modulation. On the other hand, the study demonstrates that in the case of HfSiON gate dielectrics with similar EOT, appropriate L values can be found obtaining very high output impedance current sources with reduced power consumption owing to low leakage and most of all with better parameter predictability.     

Nitrogen profile engineering in the interfacial SiON in a HfAlO/SiON gate dielectric by NO Re-oxidation

The effects of the nitrogen profile in the SiON-interfacial layer (IL) on the mobility in FETs employing a HfAlO/SiON gate dielectric have been investigated. In order to suppress the interdiffusion between HfAlO and SiON, the nitrogen concentration in SiON should be higher than 15 at%, while the substrate interface should be oxygen-rich in order to suppress the mobility reduction. By using an NO reoxidation of NH/sub 3/ formed 0.4-nm-thick silicon nitride, the mobility reduction due to the SiON-IL was successfully suppressed, and electron and hole mobility of 92% and 88% of those for SiO/sub 2/ at V/sub g/=1.1 V were obtained for HfAlO/SiON with equivalent oxide thickness (EOT) of 1.1 nm. By using nitrogen profile engineered SiON-IL, good equvalent oxide thickness (EOT) uniformity, low EOT, low gate leakage current, low defect density, and symmetrical threshold voltage were all achieved, indicating that a poly-Si/HfAlO/SiON gate stack would be a candidate as an alternative gate structure for low standby power FETs of half-pitch (hp)65 and hp45 technology nodes.     

一种提高栅氧化物介电常数的方法

从90 nm技术节点开始,等离子氮化SiON栅氧化层被广泛用作先进的CMOS器件制造。作为传统SiO2栅氧化层的替代材料,SiON栅氧化层因其具有较高的介电常数而能有效地抑制硼等栅极掺杂原子在栅氧化层中的扩散。氮化后热退火处理(Post Nitridation Anneal,PNA)是制备等离子氮化SiON栅氧化层的一个重要步骤,主要用于修复晶格损伤并形成稳定Si-N键,同时在氧化氛围下通过界面的二次氧化反应来修复SiO2/Si界面的损伤。本文通过对传统栅氧制备工艺中PNA单一高温退火工艺的温度、气体氛围进行优化,提供了一种通过提高栅氧化物的氮含量来提其高介电常数的方法。实验数据表明,与传统的制备方法相比,采用本方法所制备的SiON栅氧化层中氮含量可以提高30%以上,栅氧界面态总电荷可减少一个数量级,PMOS器件的NBTI寿命t0.1%和t50%可分别提高15.3%和32.4%。     

Effect of fluorinated silicate glass passivation layer on electrical characteristics and dielectric reliabilities for the HfO2/SiON gate stacked nMOSFET

The superior characteristics of the fluorinated hafnium oxide/oxynitride (HfO₂/SiON) gate dielectric are investigated comprehensively. Fluorine is incorporated into the gate dielectric through fluorinated silicate glass (FSG) passivation layer to form fluorinated HfO₂/SiON dielectric. Fluorine incorporation has been proven to eliminate both bulk and interface trap densities due to Hf-F and Si-F bonds formation, which can strongly reduce trap generation as well as trap-assisted tunneling during subsequently constant voltage stress, and results in improved electrical characteristics and dielectric reliabilities. The results clearly indicate that the fluorinated HfO₂/SiON gate dielectric using FSG passivation layer becomes a feasible technology for future ultrathin gate dielectrics applications.     

Challenges and performance limitations of high-k and oxynitride gate dielectrics for 90/65 nm CMOS technology

For low power applications, the increase of gate leakage current, caused by direct tunneling in ultra-thin oxide films, is the crucial factor eliminating conventional SiO₂-based gate dielectrics in sub-90 nm CMOS technology development. Recently, promising performance has been demonstrated for poly-Si/high-k and poly-Si/SiON gate stacks in addressing gate leakage requirements for low power applications. However, the use of poly-Si gate electrodes on high-k created additional issues such as channel mobility and reliability degradations, as well as Fermi level pinning of the effective gate work function. Therefore, oxynitride gate dielectrics are being proposed as an intermediate solution toward the sub-65/45 nm nodes. Apparently, an enhanced SiON gate dielectric stack was developed and reported to achieve high dielectric constant and good interfacial properties. The purpose of this paper is to provide a comprehensive review some of the device performance and limitation that high-k and oxynitride as dielectric materials are facing for sub-65/45 nm node.     

Leakage current comparison between ultra-thin Ta2O5 films and conventional gate dielectrics

Capacitors with ultra-thin (6.0-12.0 nm) CVD Ta₂O₅ film were fabricated on lightly doped Si substrates and their leakage current (I_g-V_g) and capacitance (C-V) characteristics were studied. For the first time, samples with stack equivalent oxide thickness around 2.0 nm were compared with ultra-thin silicon dioxide and silicon oxynitride. The Ta₂O₅ samples showed remarkably lower leakage current, which not only verified the advantages of ultra-thin Ta₂O₅ as dielectrics for high density DRAM's, but also suggested the possibility of its application as the gate dielectric material in MOSFET's     

Top Contact Pentacene Organic Thin Film Field Effect Transistors

Using pentacene as an active material, the organic thin film transistors were fabricated on Si_(3)N_(4)/p-Si substrates by using RF-magnetron sputtered amorphous aluminium as the gate electrode contact, and using highly doped Si as the gate electrode and substrate with plasma-enhanced chemical vapor deposited (PECVD) silicon nitride as gate dielectric. Pentacene thin films were deposited by thermal evaporation on dielectrics as the active layer, then RF-magnetron sputtered amorphous aluminium was used as the source and drain contacts. Measurement results show that field effect mobility and threshold voltage are 0.043 cm~2/(V·s) and 12.6 V, respectively, and on-off current ratio is nearly 1×10~(3).     

The performance and reliability of PMOSFET's with ultrathin siliconnitride/oxide stacked gate dielectrics with nitrided Si-SiO2interfaces prepared by remote plasma enhanced CVD and post-depositionrapid thermal annealing

Ultrathin (~1.9 nm) nitride/oxide (N/O) dual layer gate dielectrics have been prepared by the remote plasma enhanced chemical vapor deposition (RPECVD) of Si₃N₄ onto oxides. Compared to PMOSFET's with heavily doped p⁺-poly-Si gates and oxide dielectrics, devices incorporating the RPECVD stacked nitrides display reduced tunneling current, effectively no boron penetration and improved interface characteristics. By preventing boron penetration into the bulk oxide and channel region, gate dielectric reliability and short channel effects are significantly improved. The hole mobility in devices with N/O dielectrics with equivalent oxide thickness between 1.8 nm and 3.0 nm is not significantly degraded. Because nitrogen is transported to the substrate/dielectric interface during post-deposition annealing, degradation of mobility during hot carrier stressing is significantly reduced for N/O devices. Compared with oxide, the tunneling current for N/O films with ~1.9 nm equivalent oxide thickness is lower by about an order of magnitude due to the larger physical thickness. Suppression of boron transport in nitride layers is explained by a percolation model in which boron transport is blocked in sufficiently thick nitrides, and is proportional to the oxide fraction in oxynitride alloys     

Abrupt breakdown in dielectric/metal gate stacks: a potential reliability limitation?

In downscaled poly-Si gate MOSFET devices reliability margin is gained by progressive wearout. When the poly-Si gate is replaced with a metal gate, the slow wearout phase observed in ultrathin SiON and HfSiON dielectrics with poly-Si gate disappears, and with it, the reliability margin. We demonstrate for several combinations of dielectric and gate materials that the large abrupt current increase (/spl Delta/I) as compared to poly-Si is not likely due to process issues, but is an intrinsic property of the dielectric/metal gate stack. The occurrence of large /spl Delta/I is a potential limitation for the reliability of metal gate devices.     

Low frequency noise in nMOSFETs with subnanometer EOT hafnium-based gate dielectrics

This paper focuses on the noise behavior of nMOSFETs with high-k gate dielectrics (SiON/HfO₂) with an equivalent oxide thickness of 0.92 nm and using metal (TiN/TaN) as gate material. From the linear dependence of the normalized drain noise on the gate voltage overdrive we conclude that the 1/f noise is dictated by mobility fluctuations. This behavior is mainly ascribed to the reduced mobility due to the low interfacial thickness of 0.4 nm and the Hf-related defects. The gate current is more sensitive to RTS noise with respect to the drain current noise. Cross-correlation measurements between drain and gate noise are used as a tool for discriminating between noise mechanisms which generate different fluctuation levels at the gate and drain terminal.     

高k纳米MOSFET的关态泄漏电流的研究

对纳米MOSFET关断态的栅电流、漏电流和衬底电流进行了模拟,指出边缘直接隧穿电流(IEDT)远远大于传统的栅诱导泄漏电流(IGIDL)、亚阈区泄漏电流(ISUB)及带间隧穿电流(IBTBT)。对50 nm和90 nm MOSFET器件的Id-Vg特性进行了比较,发现在高Vdd下,关态泄漏电流(Ioff)随IEDT的增加而不断增大,并且器件尺寸越小,Ioff越大。高k栅介质能够减小IEDT,进而减小了Ioff,其中HfSiON、HfLaO可以使边缘隧穿电流减小2～5个数量级且边缘诱导的势垒降低(FIBL)效应很小。但当栅介质的k>25以后,由于FIBL效应,关态泄漏电流反而增大。     

Investigation of hole-tunneling current through ultrathinoxynitride/oxide stack gate dielectrics in p-MOSFETs

The systematic investigation of hole tunneling current through ultrathin oxide, oxynitride, oxynitride/oxide (N/O) and oxide/oxynitride/oxide (ONO) gate dielectrics in p-MOSFETs using a physical model is reported for the first time. The validity of the model is corroborated by the good agreement between the simulated and experimental results. Under typical inversion biases (|VG|<2 V), hole tunneling current is lower through oxynitride and oxynitride/oxide with about 33 at.% N than through pure oxide and nitride gate dielectrics. This is attributed to the competitive effects of the increase in the dielectric constant, and hence dielectric thickness, and decrease in the hole barrier height at the dielectric/Si interface with increasing with N concentration for a given electrical oxide thickness (EOT). For a N/O stack film with the same N concentration in the oxynitride, the hole tunneling current decreases monotonically with oxynitride thickness under the typical inversion biases. For minimum gate leakage current and maintaining an acceptable dielectric/Si interfacial quality, an N/O stack structure consisting of an oxynitride layer with 33 at.% N and a 3 Å oxide layer is proposed. For a p-MOSFET at an operating voltage of -0.9 V, which is applicable to the 0.7 μm technology node, this structure could be scaled to EOT=12 Å if the maximum allowed gate leakage current is 1 A/cm² and EOT=9 Å if the maximum allowed gate leakage current is 100 A/cm²     

Two silicon nitride technologies for post-SiO2 MOSFETgate dielectric

P-MOSFETs with 14 Å equivalent oxide thickness (EOT) were fabricated using both JVD Si₃N₄ and RTCVD Si₃ N₄/SiO_xN_y gate dielectric technologies. With gate length down to 80 nm, the two technologies produced very similar device performances, such as drive current and gate tunneling current. The low gate leakage current, good device characteristics and compatibility with conventional CMOS processing technology make both nitride gate dielectrics attractive candidates for post-SiO₂ scaling. The fact that two significantly different technologies produced identical results suggests that the process window should be quite large