Adsorption properties of Congo Red from aqueous solution onto surfactant-modified montmorillonite

A series of surfactant-modified montmorillonites (MMT) were prepared using octyltrimethylammonium bromide (OTAB), dodecyltrimethylammonium bromide (DTAB), cetyltrimethylammonium bromide (CTAB) and stearyltrimethylammonium bromide (STAB), and the organification of MMT was proved by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron micrographic (SEM) and transmission electron microscope (TEM). The adsorption of Congo Red (CR) anionic dye from aqueous solution onto surfactant-modified MMT was carried out. Compared with MMT, the adsorption capacity of surfactant-modified MMT for CR was greatly enhanced and MMT modified with CTAB (2.0 CEC) exhibited the higher adsorption capacity. The effects of pH value of the dye solution, adsorption temperature, adsorption time and the initial dye concentration on the adsorption capacity of CR on CTAB-MMT have been investigated. The results showed that the adsorption kinetic of CR on CTAB-MMT could be best described by the pseudo-second-order model and that the adsorption isotherm of CR was in good agreement with the Langmuir equation. The IR spectra and SEM analysis also revealed that the adsorption of CTAB-MMT was a chemical adsorption process between CTAB and the NH(2), -N=N- and SO(3) groups of CR.     

Adsorption of nickel(II) from aqueous solution onto activated carbon prepared from almond husk

Activated carbon was prepared from almond husk by activating without (MAC-I) and with (MAC-II) H(2)SO(4) at different temperatures. The ability of the activated carbon to remove nickel(II) ions from aqueous solutions by adsorption has been investigated under several conditions such as pH, carbonisation temperature of husk, initial concentration of metal ions, contact time, and adsorbent concentration. Optimal conditions were pH 5.0, the carbonisation temperature of 700 degrees C, 50 min of contact time and adsorbent concentration of 5 g/l. The results indicate that the effective uptake of Ni(II) ions was obtained by activating the carbon, prepared from almond husk at 700 degrees C, through the addition of H(2)SO(4). The removal of Ni(II) were found to be 97.8% at initial concentration of 25mg/l and the adsorbent concentration of 5 g/l. When the adsorbent concentration was increased up to 40 g/l, the adsorption density decreased from 4.89 to 0.616 mg/g for MAC-II. In the isotherm studies, the experimental adsorption data fitted reasonably well the Langmuir isotherm for both MAC-I and MAC-II.     

Removal of Basic Red 46 dye from aqueous solution by adsorption onto Moroccan clay

In this study, Moroccan crude clay of Safi, which was characterized by X-ray diffraction, is used as adsorbent for the investigation of the adsorption kinetics, isotherms and thermodynamic parameters of the Basic Red 46 (BR46) in aqueous solutions at various dye concentrations, adsorbent masses and pH values. The results showed that the adsorption capacity of the dye increased by initial dye concentration and pH values. Two kinetic models (the pseudo-first-order and the pseudo-second-order) were used to calculate the adsorption rate constants. The adsorption kinetics of the basic dye followed pseudo-second-order model. The experimental data isotherms were analyzed using the Langmuir, Freundlich and Dubinin–Radushkevish equations. The monolayer adsorption capacity for BR46 dye is 54 mg/g of crude clay. Nearly 20 min of contact time was found to be sufficient for the dye adsorption to reach equilibrium. Thermodynamical parameters were also evaluated for the dye–adsorbent system and revealed that the adsorption process is exothermic in nature.     

Adsorption of bisphenol-A from aqueous solution onto minerals and carbon adsorbents

The adsorption behaviors of bisphenol-A, which has been listed as one of endocrine disrupting chemicals, from aqueous solution onto four minerals including andesite, diatomaceous earth, titanium dioxide, and activated bleaching earth, and two activated carbons with coconut-based and coal-based virgins were examined in this work. Based on the adsorption results at the specified conditions, the adsorption capacities of activated carbons are significantly larger than those of mineral adsorbents, implying that the former is effective for removal of the highly hydrophobic adsorbate from the aqueous solution because of its high surface area and low surface polarity. The adsorption capacities of bisphenol-A onto these mineral adsorbents with different pore properties are almost similar in magnitude mainly due to the weakly electrostatic interaction between the mineral surface with negative charge and the target adsorbate with hydrophobic nature. Further, a simplified kinetic model, pseudo-second-order, was tested to investigate the adsorption behaviors of bisphenol-A onto the two common activated carbons at different solution conditions. It was found that the adsorption process could be well described with the pseudo-second-order model. The kinetic parameters of the model obtained in the present work are in line with the pore properties of the two adsorbents.     

The adsorption of cationic dye from aqueous solution onto acid-activated andesite

The adsorption of cationic dye (i.e., methylene blue) onto acid-activated andesite in aqueous solution was studied in a batch system with respect to its kinetics as a function of agitation speed, initial adsorbate concentration, pH, and adsorbent mass. It was found that the resulting acid-activated adsorbent possessed a mesoporous structure with BET surface areas at around 60m(2)/g. The surface characterization of acid-activated andesite was also performed using the zeta-potential measurements, indicating that the charge sign on the surface of the andesite should be negative in a wide pH range (i.e., 3-11). Furthermore, a simplified kinetic model, pseudo-second-order, was tested to investigate the adsorption behaviors of methylene blue onto the clay samples treated under different process conditions. It was found that the adsorption process could be well described with the model. The adsorption capacity parameter of the model obtained in the present work was significantly in line with the process parameters.     

Adsorption of Acid Red 57 from aqueous solutions onto surfactant-modified sepiolite

The adsorption of Acid Red 57 (AR57) onto surfactant-modified sepiolite was investigated in aqueous solution in a batch system with respect to contact time, pH and temperature. The surface modification of surfactant-modified sepiolite was controlled using the FTIR technique. The pseudo-first-order, pseudo-second-order kinetic models and the intraparticle diffusion model were used to describe the kinetic data and the rate constants were evaluated. The experimental data fitted very well the pseudo-second-order kinetic model and also followed the intraparticle diffusion model up to 90 min, whereas diffusion is not only the rate controlling step. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were also determined. The Freundlich model agrees with experimental data well. The activation energy, change of free energy, enthalpy and entropy of adsorption were also evaluated for the adsorption of AR57 onto surfactant-modified sepiolite. The results indicate that surfactant-modified sepiolite could be employed as low-cost material for the removal of textile dyes from effluents.     

Adsorption of reactive dye from an aqueous solution by chitosan: isotherm, kinetic and thermodynamic analysis

The adsorption of Remazol black 13 (Reactive) dye onto chitosan in aqueous solutions was investigated. Experiments were carried out as function of contact time, initial dye concentration (100-300mg/L), particle size (0.177, 0.384, 1.651mm), pH (6.7-9.0), and temperature (30-60 degrees C). The equilibrium adsorption data of reactive dye on chitosan were analyzed by Langmuir and Freundlich models. The maximum adsorption capacity (qm) has been found to be 91.47-130.0mg/g. The amino group nature of the chitosan provided reasonable dye removal capability. The kinetics of reactive dye adsorption nicely followed the pseudo-first and second-order rate expression which demonstrates that intraparticle diffusion plays a significant role in the adsorption mechanism. Isotherms have also been used to obtain the thermodynamic parameters such as free energy, enthalpy and entropy of adsorption. The positive value of the enthalpy change (0.212kJ/mol) indicated that the adsorption is endothermic process. The results indicate that chitosan is suitable as adsorbent material for adsorption of reactive dye form aqueous solutions.     

Adsorption dynamics of chlorinated hydrocarbons from multi-component aqueous solution onto activated carbon

The results and a numerical simulation of studies on dynamics of the adsorption from seven-component aqueous solution of light chlorinated hydrocarbons on activated carbon have been presented. Aqueous solution of 1,2-dichloroethane (12DCE), 1,1,2,2-tetrachloroethane (S-TET), chloroform (CHCl(3)), carbon tetrachloride (CCl(4)), 1,1-dichloroethene (VDC), perchloroethene (PER) and 1,1,2-trichloroethene (TRI) was used. Concentrations of chlorohydrocarbons were similar as in wastewater from vinyl chloride plant. A cell model that incorporates the diffusion through a laminar layer of liquid around a particle was used to describe the experimental results. The applied calculation methods, which take kinetics into account, allows to well describe a phenomenon of dynamic adsorption. Mean relative deviations between the experimental and calculated values amounted 17%. The breakthrough curves become steeper along with an increase of the bed height. A consistency of the experimental results with those calculated indicates for a negligible contribution of the axial diffusion on the dynamic adsorption process of light chlorinated hydrocarbons from aqueous solution under the hydrodynamic conditions corresponding to the Reynolds number equal to 1.3. Determined optimal bed height for waste linear flow rate-15 cm/min is in the range 80-120 cm.     

Adsorption of malachite green from aqueous solution onto carbon prepared from Arundo donax root

Arundo donax root carbon (ADRC), a new adsorbent, was prepared from Arundo donax root by carbonization. The surface area of the adsorbent was determined 158 m²/g by N₂ adsorption isotherm. Batch adsorption experiments were carried out for the removal of malachite green (MG) from aqueous solution using ADRC as adsorbent. The effects of various parameters such as solution pH (3–10), carbon dose (0.15–1.0 g/100 ml) and initial MG concentration (10–100 mg/l) on the adsorption system were investigated. The effective pH was 5–7 and the optimum adsorbent dose was found to be 0.6 g/100 ml. Equilibrium experimental data at 293, 303 and 313 K were better represented by Langmuir isotherm than Freundlich isotherm using linear and non-linear methods. Thermodynamic parameters such as ΔG, ΔH and ΔS were also calculated. The negative Gibbs free energy change and the positive enthalpy change indicated the spontaneous and endothermic nature of the adsorption. The adsorption equilibrium time was 180 min. Adsorption kinetics was determined using pseudo-first-order model, pseudo-second-order model and intraparticle diffusion model. The results showed that the adsorption of MG onto ADRC followed pseudo-second-order model.     

Investigation of a basic dye removal from aqueous solution onto chemically modified Unye bentonite

The adsorption behavior of crystal violet (CV⁺) from aqueous solution onto magnesium-oxide coated bentonite (MCB) sample was investigated as a function of parameters such as initial CV⁺ concentration, contact time and temperature. The Langmuir, and Freundlich adsorption models were applied to describe the equilibrium isotherms. The Langmuir monolayer adsorption capacity of MCB were estimated as 496 mg/g. The pseudo-first-order, pseudo-second-order kinetic and the intra-particle diffusion models were used to describe the kinetic data and rate constants were evaluated. The values of the energy (E_a), enthalpy (ΔH^≠) and entropy of activation (ΔS^≠) were 56.45 kJ/mol, 53.90 kJ/mol and −117.26 J/mol K, respectively, at pH 6.5.     

Adsorption of zinc(II) from an aqueous solution onto activated carbon.

Adsorption isotherms were measured experimentally for Zn(II) adsorption from aqueous solution onto commercial activated carbons C, F-400, F-300 and Centaur HSL in a batch adsorber. The effects of carbon type and solution pH on adsorption isotherms were evaluated in this work. Nearly three times as much Zn(II) adsorbed onto C carbon as on the other three carbon types. The adsorption isotherm for Zn(II) was dependent on solution pH since Zn(II) did not adsorb to carbon below pH 2, and the adsorption isotherm increased as pH increased from 3 to 7. The adsorption isotherm of Zn(II) on C carbon was temperature independent while on F-400 the isotherm showed unusual behavior as temperature increased.     

Adsorption of bisphenol A from aqueous solution onto activated carbons with different modification treatments

Two commercial carbons (W20 and F20) had been selectively modified with nitric acid and thermal treatment under a flow of N(2) in present study to adsorb bisphenol A from aqueous solution. The results indicated that the experimental data were well described with pseudo-second-order kinetic model. W20 and its thermal modified sample (W20N) represented a better adsorption capacity, and the equilibrium adsorption amounts reached 382.12 and 432.34 mg/g, respectively. Further, effects of temperature, pH and ionic strength on bisphenol A adsorption onto W20 and W20N had been examined. It was found that the adsorbed amount of bisphenol A decreased with the increase of temperature from 288 to 318 K and changed little with the increase of pH from 5.0 to 9.0. At pH 11.0, the two activated carbons represented the weakest adsorption capacity. The adsorption capacities of bisphenol A onto W20 and W20N first decreased and then increased with the increasing of ionic strength.     

Adsorption of phenolic compounds from aqueous solution onto a macroporous polymer and its aminated derivative: isotherm analysis

Adsorption of phenolic compounds from aqueous solution to a macroporous polymeric adsorbent (CHA-111), its animated derivative (MCH-111) and a reference weakly anion exchanger (ND-900) was studied. Experimental results indicated that amino functional groups on the polymeric matrix play an important role in phenol adsorption by MCH-111 and ND-900, which was attributed to the formation of hydrogen bonding between the phenol molecule and the amino group on the polymeric matrix. The semi-empirical Freundlich isotherm equation and its reduced form were employed to interpret the adsorption behavior. A site energy distribution model based on the Polanyi adsorption potential theory can elucidate the adsorption mechanism reasonably.     

Optimization of Bomaplex Red CR-L dye removal from aqueous solution by electrocoagulation using aluminum electrodes

In this paper, Taguchi method was applied to determine the optimum dye removal from aqueous solution by electrocoagulation using aluminum electrodes. An orthogonal array (OA(16)) experimental design that allows to investigate the simultaneous variations of five parameters (initial dye concentration, initial pH of the solution, supporting electrolyte concentration, supporting electrolyte type and current density) having four levels was employed to evaluate the effects of experimental parameters. Performance measure analysis was followed by performing a variance analysis, in order to determine the optimum levels and relative magnitude of the effect of parameters. Because the desired characteristic for response has been maximum decolorization, Taguchi's 'the larger the better' performance formula was used. While the optimum conditions were found to be initial dye concentration of 100 mg/L, initial pH of the solution of 3, supporting electrolyte concentration of 0.0 mM, supporting electrolyte type of CaCl(2) and current density of 0.50 mA/cm(2). Under these optimum conditions, energy consumption is 0.607 kWh/kg dye, when the system evaluated also based on the energy consumptions it can be said that optimum conditions should be modified as follows: supporting electrolyte concentration of 2.5 mM; supporting electrolyte type NaCl, for 100 mg/L initial dye concentration; initial pH of the solution of 3; current density of 0.50 mA/cm(2).     

Adsorption of reactive dye onto carbon nanotubes: equilibrium, kinetics and thermodynamics

The adsorption efficiency of carbon nanotubes for Procion Red MX-5B at various pHs and temperatures was examined. The amount adsorbed increased with the CNTs dosage; however, the adsorption capacity initially increased with the CNTs dosage (<0.25 g/l) and then declined as the CNTs dosage increased further (>0.25 g/l). The linear correlation coefficients and standard deviations of Langmuir and Freundlich isotherms were determined and the results revealed that Langmuir isotherm fitted the experimental results well. Kinetic analyses were conducted using pseudo first- and second-order models and the intraparticle diffusion model. The regression results showed that the adsorption kinetics were more accurately represented by a pseudo second-order model. Changes in the free energy of adsorption (DeltaG degrees ), enthalpy (DeltaH degrees ) and entropy (DeltaS degrees), as well as the activation energy (E(a)) were determined. DeltaH degrees and DeltaS degrees were 31.55 kJ/mol and 216.99J/molK, respectively, at pH 6.5 and 41.47 kJ/mol and 244.64 J/molK at pH 10. The activation energy was 33.35 kJ/mol at pH 6.5. DeltaH degrees, DeltaG degrees and E(a) all suggested that the adsorption of Procion Red MX-5B onto CNTs was by physisorption.     

Biosorption of chromium(VI) ion from aqueous solutions using walnut, hazelnut and almond shell

The potential to remove Cr(VI) ion from aqueous solutions through biosorption using, the shells of Walnut (WNS) (Juglans regia), Hazelnut (HNS) (Corylus avellana) and Almond (AS) (Prunus dulcis) was investigated in batch experiments. The equilibrium adsorption level was determined to be a function of the solution contact time and concentration. Kinetic experiments revealed that the dilute chromium solutions reached equilibrium within 100 min. The biosorptive capacity of the shells was dependent on the pH of the chromium solution, with pH 3.5 being optimal. Adsorption of Cr(VI) ion uptake is in all cases pH-dependent showing a maximum at equilibrium pH values between 2.0 and 3.5, depending on the biomaterial, that correspond to equilibrium pH values of 3.5 for (WNS), 3.5 for (HNS) and 3.2 for (AS). The adsorption data fit well with the Langmuir isotherm model. The sorption process conformed to the Langmuir isotherm with maximum Cr(VI) ion sorption capacities of 8.01, 8.28, and 3.40 mg/g for WNS, HNS and AS, respectively. Percentage removal by WNS, HNS and AS was 85.32, 88.46 and 55.00%, respectively at a concentration of 0.5 mM. HNS presented the highest adsorption capacities for the Cr(VI) ion.     

Adsorption of methylene blue onto hazelnut shell: Kinetics, mechanism and activation parameters

The adsorption kinetics of methylene blue (MB) on the hazelnut shell with respect to the initial dye concentration, pH, ionic strength, particle size and temperature were investigated. The rate and the transport/kinetic processes of MB adsorption were described by applying the first-order Lagergren, the pseudo-second-order, mass transfer coefficient and the intraparticle diffusion models. Kinetic studies showed that the kinetic data were well described by the pseudo-second-order kinetic model. Significant increases in initial adsorption rate were observed with the increase in temperature followed by pH and initial MB concentration. The intraparticle diffusion was found to be the rate-limiting step in the adsorption process. Adsorption activation energy was calculated to be 45.6kJmol(-1). The values of activation parameters such as free energy (DeltaG(*)), enthalpy (DeltaH(*)) and entropy (DeltaS(*)) were also determined as 83.4kJmol(-1), 42.9kJmol(-1) and -133.5Jmol(-1)K(-1), respectively.     

Adsorption characteristics of Cu(II) and Pb(II) onto expanded perlite from aqueous solution

The adsorption characteristics of Cu(II) and Pb(II) onto expanded perlite (EP) from aqueous solution were investigated with respect to the changes in pH of solution, adsorbent dosage, contact time and temperature of solution. For the adsorption of both metal ions, the Langmuir isotherm model fitted to equilibrium data better than the Freundlich isotherm model. Using the Langmuir model equation, the monolayer adsorption capacity of EP was found to be 8.62 and 13.39 mg/g for Cu(II) and Pb(II) ions, respectively. Dubinin-Radushkevich (D-R) isotherm model was also applied to the equilibrium data and the mean free energies of adsorption were found as 10.82 kJ/mol for Cu(II) and 9.12 kJ/mol for Pb(II) indicating that the adsorption of both metal ions onto EP was taken place by chemical ion-exchange. Thermodynamic functions, the change of free energy (DeltaG degrees ), enthalpy (DeltaH degrees ) and entropy (DeltaS degrees ) of adsorption were also calculated for each metal ions. These parameters showed that the adsorption of Cu(II) and Pb(II) ions onto EP was feasible, spontaneous and exothermic at 20-50 degrees C. Experimental data were also evaluated in terms of kinetic characteristics of adsorption and it was found that adsorption process for both metal ions followed well pseudo-second-order kinetics.     

The adsorption of basic dye (Astrazon Blue FGRL) from aqueous solutions onto sepiolite, fly ash and apricot shell activated carbon: kinetic and equilibrium studies

In this study, sepiolite, fly ash and apricot stone activated carbon (ASAC) were used as adsorbents for the investigation of the adsorption kinetics, isotherms and thermodynamic parameters of the basic dye (Astrazon Blue FGRL) from aqueous solutions at various concentrations (100-300 mg/L), adsorbent doses (3-12 g/L) and temperatures (303-323 K). The result showed that the adsorption capacity of the dye increased with increasing initial dye concentration, adsorbent dose and temperature. Three kinetic models, the pseudo-first-order, second-order, intraparticle diffusion, were used to predict the adsorption rate constants. The kinetics of adsorption of the basic dye followed pseudo-second-order kinetics. Equations were developed using the pseudo-second-order model which predicts the amount of the basic dye adsorbed at any contact time, initial dye concentration and adsorbent dose within the given range accurately. The adsorption equilibrium data obeyed Langmuir isotherm. The adsorption capacities (Q0) calculated from the Langmuir isotherm were 181.5 mg/g for ASAC, 155.5 mg/g for sepiolite and 128.2 mg/g for fly ash at 303 K. Thermodynamical parameters were also evaluated for the dye-adsorbent systems and revealed that the adsorption process was endothermic in nature.     

Adsorption of acid dye from water onto pristine and acid-activated clays in fixed beds

The adsorption of an acid dye from water onto pristine and HCl-activated montmorillonites in fixed beds was investigated. Experiments were carried out as a function of liquid flow rate, initial dye concentration, and bed height. The adsorption capacity of acid dye onto pristine clay could be largely improved when the clay was activated by HCl. A mass transfer model that involves only two parameters, tau (50% breakthrough time) and kappa (adsorption rate constant), was proposed. This model could satisfactorily describe the measured breakthrough curves of acid dye in fixed beds (standard deviation <6%). It was shown that the value of tau decreased with increasing liquid flow rate. The effect of the type of clay (pristine, acid-activated) on the values of kappa, tau, and adsorption capacity was discussed, and the application potential of acid-activated clay for adsorption removal of acid dye from water was also demonstrated.