Mechanical properties of SiCf/SiC composites with alternating PyC/BN multilayer interfaces

Alternating pyrolytic carbon/boron nitride (PyC/BN)_n multilayer coatings were applied to the KD–II silicon carbide (SiC) fibres by chemical vapour deposition technique to fabricate continuous SiC fibre-reinforced SiC matrix (SiC_f/SiC) composites with improved flexural strength and fracture toughness. Three-dimensional SiC_f/SiC composites with different interfaces were fabricated by polymer infiltration and pyrolysis process. The microstructure of the coating was characterised by scanning electron microscopy, X–photoelectron spectroscopy and transmission electron microscopy. The interfacial shear strength was determined by the single-fibre push-out test. Single-edge notched beam (SENB) test and three-point bending test were used to evaluate the influence of multilayer interfaces on the mechanical properties of SiC_f/SiC composites. The results indicated that the (PyC/BN)_n multilayer interface led to optimum flexural strength and fracture toughness of 566.0?MPa and 21.5?MPa?m^1/2, respectively, thus the fracture toughness of the composites was significantly improved.     

裂解碳包覆对SiC纳米纤维增强SiC陶瓷基复合材料性能的影响

以SiC纳米纤维(SiC_nf)为增强体,通过化学气相沉积在SiC纳米纤维表面沉积裂解碳(PyC)包覆层,并与SiC粉体、Al₂O₃-Y₂O₃烧结助剂共混制备陶瓷素坯,采用热压烧结工艺制备质量分数为10%的SiC纳米纤维增强SiC陶瓷基(SiC_nf/SiC)复合材料。研究了PyC包覆层沉积时间对SiC_nf/SiC陶瓷基复合材料的致密度、断裂面微观形貌和力学性能的影响。结果表明:在1 100 ℃下沉积60 min制备的PyC包覆层厚度为10 nm,且为结晶度较好的层状石墨结构;相比于纤维表面无包覆层的复合材料,复合材料的断裂韧性提高了35%,达到最大值(19.35±1.17) MPa·m^1/2,抗弯强度为(375.5±8.5) MPa,致密度为96.68%。复合材料的断裂截面可见部分纳米纤维拔出现象,但SiC_nf/SiC陶瓷基复合材料界面结合仍较强,纳米纤维拔出短,表现为脆性断裂。     

Appropriate thickness of pyrolytic carbon coating on SiC fiber reinforcement to secure reasonable quasi-ductility on NITE SiC/SiC composites

Pyrolytic carbon (PyC) coating of silicon carbide (SiC) fibers is an important technology that creates quasi-ductility to SiC/SiC composites. Nano-infiltration and transient eutectic-phase (NITE) process is appealing for the fabrication of SiC/SiC composites for use in high temperature system structures. However, the appropriate conditions for the PyC coating of the composites have not been sufficiently tested. In this research, SiC fibers, with several thick PyC coatings prepared using a chemical vapor infiltration continuous furnace, were used in the fabrication of NITE SiC/SiC composites. Three point bending tests of the composites revealed that the thickness of the PyC coating affected the quasi-ductility of the composites. The composites reinforced by 300?nm thick coated SiC fibers showed a brittle fracture behavior; the composites reinforced 500 and 1200?nm thick PyC coated SiC fibers exhibited a better quasi-ductility. Transmission electron microscope research revealed that the surface of the as-coated PyC coating on a SiC fiber was almost smooth, but the interface between the PyC coating and SiC matrix in a NITE SiC/SiC composite was very rough. The thickness of the PyC coating was considered to be reduced maximum 400?nm during the composite fabrication procedure. The interface was possibly damaged during the composite fabrication procedure, and therefore, the thickness of the PyC coating on the SiC fibers should be thicker than 500?nm to ensure quasi-ductility of the NITE SiC/SiC composites.     

Oxidation behavior of oxidation protective coatings for PIP-C/SiC composites at 1500 °C

Three-dimensional carbon fiber reinforced silicon carbide (C/SiC) composites were fabricated by precursor infiltration and pyrolysis (PIP) with polycarbosilane as the matrix precursor, SiC coating prepared by chemical vapor deposition (CVD) and ZrB₂-SiC/SiC coating prepared by CVD with slurry painting were applied on C/SiC composites, respectively. The oxidation of three samples at 1500 °C was compared and their microstructures and mechanical properties were investigated. The results show that the C/SiC without coating is distorted quickly. The mass loss of SiC coating coated sample is 4.6% after 2 h oxidation and the sample with ZrB₂-SiC/SiC multilayer coating only has 0.4% mass loss even after oxidation. ZrB₂-SiC/SiC multilayer coating can provide longtime protection for C/SiC composites. The mode of the fracture behavior of C/SiC composites was also changed. When with coating, the fracture mode of C/SiC composites became brittle. When after oxidation, the fracture mode of C/SiC composites without and with coating also became brittle.     

SiCf/SiO2复合材料的制备及界面层对其力学性能的影响

以碳化硅(SiC)纤维为增强体,采用真空浸渍法制备了2.5维连续SiC纤维增韧的SiO2基(SiCf/SiO2)复合材料,研究了SiC纤维编织体上不同的界面层对SiCf/SiO2复合材料力学性能的影响.化学气相渗透(CVI)法制备的热解碳(PyC)和PyC/SiC双层界面层分别使材料的抗弯强度由无界面层的52.2 MPa提高至67.4 MPa和180.3 MPa,但均使材料的韧性降低.用扫描电镜观察了材料的断口形貌,结果表明,PyC和PyC/SiC层不仅提高了材料的抗弯强度,而且增加了基体同纤维间的结合力,使基体有效地将载荷传递给纤维.PyC/SiC层能有效地保护SiC纤维,防止烧结过程中释放出的结晶水对纤维的损伤,有助于提高材料的力学性能.     

Mechanical properties and strengthening mechanism of SiCf/SiC mini-composites modified by SiC nanowires

The effects of the SiC nanowires (SiCNWs) and PyC interface layers on the mechanical and anti-oxidation properties of SiC fiber (SiC_f)/SiC composites were investigated. To achieve this, the PyC layer was coated on the SiC_f using a chemical vapour infiltration (CVI) method. Then, SiCNWs were successfully coated on the surface of SiC_f/PyC using the electrophoretic deposition method. Finally, a thin PyC layer was coated on the surface of SiC_f/PyC/SiCNWs. Three mini-composites, SiC_f/PyC/SiC, SiC_f/PyC/SiCNWs/SiC, and SiC_f/PyC/SiCNWs/PyC/SiC, were fabricated using the typical precursor infiltration and pyrolysis method. The morphologies of the samples were examined using scanning electron microscopy and energy dispersive X-ray spectrometry. Tensile and single-fibre push-out tests were carried out to investigate the mechanical performance and interfacial shear strength of the composites before and after oxidization at 1200 °C. The results revealed that the SiC_f/PyC/SiCNWs/SiC composites showed the best mechanical and anti-oxidation performance among all the composites investigated. The strengthening and toughening is mainly achieved by SiCNWs optimization of the interfacial bonding strength of the composite and its own nano-toughening. On the basis of the results, the effects of SiCNWs on the oxidation process and retardation mechanism of the SiC_f/SiC mini-composites were investigated.     

Effect of SiC nanowires on the mechanical properties and thermal conductivity of 3D-SiCf/SiC composites prepared via precursor infiltration pyrolysis

In this study, SiC nanowires (SiC_NWS) were grown in situ on the surface of PyC interface through chemical vapor infiltration (CVI) to improve the mechanical characteristics and thermal conductivity of three-dimensional SiC_f/SiC composites fabricated via precursor infiltration pyrolysis (PIP). The effect of SiC_NWS on the properties of the obtained composites was investigated by comparing them with conventional SiC_f/PyC/SiC composites. After the deposition of SiC_NWS, the flexural strength of the SiC_f/SiC composites was found to increase by 46 %, and the thermal conductivity showed an obvious increase at 25?1000 °C. The energy release of the composites in the damage evolution process was analysed by acoustic emission. The results indicated that the damage evolution process was delayed owing to the decrease in porosity, the crack deflection and bridging of the SiC_NWS. Furthermore, the excellent thermal conductivity was attributed to the thermally conductive pathways formed by the SiC_NWS in the dense structure.     

Improvement of toughness of reaction bonded silicon carbide composites reinforced by surface-modified SiC whiskers

To improve the reliability, especially the toughness, of the reaction bonded silicon carbide (RBSC) ceramics, silicon carbide whiskers coated with pyrolytic carbon layer (PyC-SiC_w) by chemical vapor deposition (CVD) were introduced into the RBSC ceramics to fabricate the SiC_w/RBSC composites in this study. The microstructures and properties of the PyC-SiC_w/RBSC composites under different mass fraction of nano carbon black and PyC-SiC_w were investigated methodically. As a result, a bending strength of 550 MPa was achieved for the composites with 25 wt% nano carbon black, and the residual silicon decreased to 11.01 vol% from 26.58 vol% compared with the composite of 15 vol% nano carbon black. The fracture toughness of the composites reinforced with 10 wt% PyC-SiC_w, reached a high value of 5.28 MPa m^1/2, which increased by 39% compared to the RBSC composites with 10 wt% SiC_w. The residual Si in the composites deceased below to 7 vol%, resulting from the combined actively reaction of nano carbon black and PyC with more Si. SEM and TEM results illustrated that the SiC_w were protected by PyC coating. A thin SiC layer formed of outer surface of whiskers can provide a suitable whisker-matrix interface, which is in favor of crack deflection, SiC_w bridging and pullout to improve the bending strength and toughness of the SiC_w/RBSC composites.     

Interfacial optimization of SiC nanocomposites reinforced by SiC nanowires with high volume fraction

High volume fraction SiC nanowires-reinforced SiC composites (SiCNWs/SiC) were prepared by hybrid process of chemical vapor infiltration and polymer impregnation/pyrolysis in this research. SiCNWs networks are first to be made promising a high volume fraction (20 vol%), and the pyrolytic carbon (PyC) interphase with 5 nm is designed on SiCNWs surface to optimize the bonding condition between SiCNWs and SiC matrix. Nanoindentation shows a modulus of 494 ± 14 GPa of SiCNWs/SiC composites without interphase comparing to the one with PyC interphase of 452 ± 13 GPa. However, the 3-point bending test shows a higher strength of the composite with PyC interphase (273 ± 32 MPa) comparing with the one without interphase (240 ± 38 MPa). The fracture surface is observed under SEM, which shows a longer SiCNWs pullout of the composite with PyC interphase. The energy dissipation during the 3-point bending test is calculated by the length of nanowire pull-out, it demonstrates that the SiCNWs with PyC interphase possess better performance for toughening composite. Further characterization proves that the PyC interphase can give SiCNWs/SiC composites higher fracture toughness (4.49 ± 0.44 MPa·m^1/2) than the composites without interphase (3.66 ± 0.28 MPa·m^1/2).     

Fine study of hierarchical interphase constructed by boron nitride and carbon nanotubes in SiCf/SiC composites

A fine study of the interfacial part in the silicon carbide fiber (SiC_f) reinforced silicon carbide (SiC) composites was conducted by transmission electron microscopy. The boron nitride (BN) and carbon nanotubes (CNTs) were progressively coated on the SiC_f by chemical vapor deposition method to form a hierarchical structure. Three composites with different interfaces, SiC_f–CNTs/SiC, SiC_f@BN/SiC, and SiC_f@BN–CNTs/SiC, were fabricated by polymer infiltration and pyrolysis method. The interfaces and microstructures of the three composites were carefully characterized to investigate the improvement mechanism of strength and toughness. The results showed that BN could protect the surface of SiC_f from corrosion and oxidation so that improved the possibility of debonding and pullout. CNTs could avoid the propagation of cracks in the composites so that improved the damage resistance of the matrix. The synergistic reinforcement brought by BN and CNTs interfaces made the SiC_f@BN–CNTs/SiC composites with a tensile fracture strength as high as 359 MPa, with an improvement of 23% compared to that of SiC_f@BN/SiC.     

Effects of the single layer CVD SiC interphases on the mechanical properties of the SiCf/SiC composites fabricated by PIP process

Owing to the degradation of the mechanical properties of the SiC fiber reinforced SiC matrix (SiCf/SiC) composites with the pyrocarbon (PyC) and BN interphases under oxidation environment and neutron irradiation, single layer SiC interphases prepared by chemical vapor deposition (CVD) process were employed to substitute for them. Effects of the CVD SiC interphases on the mechanical properties and interfacial characteristics of the SiCf/SiC composites fabricated by precursor infiltration and pyrolysis (PIP) process were investigated. Compared with the as-received SiCf/SiC composites, the SiCf/SiC composites with the single layer CVD SiC interphases exhibit an obvious toughened fracture behavior, the flexural strength of which is about 4 times that of the as-received SiCf/SiC composites. From the microstructural analysis, it can be confirmed that the SiC interphases play a key part in protecting the fibers from damage during composite preparation and weakening interfacial bonding, which can provide high in situ fiber strength and appropriate interfacial bonding strength for the SiCf/SiC composites.     

Fabrication of a 3D4d braided SiCf/SiC composite via PIP process assisted with an EPD method

In order to improve the thermal conductivity and full-fill the gaps between the fiber bundles for three-dimensional four-directional (3D4d) braided SiC_f/SiC composites, 500?nm submicron-sized β-SiC particles were introduced into the 3D4d preform by an electrophoretic deposition (EPD) method. ζ-potential of the KD-Ⅱ SiC fibers and the aqueous suspension of the β-SiC particles were analyzed, as well as the efficiency of the deposition. After densified via PIP process, microstructure, three-point bending strength and thermal conductivity of the composite were investigated. The results showed that, SiC particles filled the gaps between the SiC fiber bundles efficiently, and thermal conductivity of the composites fabricated through PIP process assisted by EPD was 2.3 times that of the composites fabricated via PIP only. The bending strength of the EPD-composites was 647.08?±?69.53?MPa, which decreased to 2/3 of that of the composites manufactured only by PIP, owing to the reduction of fiber volume fraction and the damages to the interface coatings and fibers under the action of the electric field.     

Ring compression properties of SiCf/SiC composites prepared by chemical vapor infiltration

SiC fiber reinforced SiC matrix (SiC_f/SiC) composites prepared by chemical vapor infiltration are one of promising materials for nuclear fuel cladding tube due to pronounced low radioactivity and excellent corrosion resistance. As a structure component, mechanical properties of the composites tubes are extremely important. In this study, three kinds of SiC_f preform with 2D fiber wound structure, 2D plain weave structure and 2.5D shallow bend-joint structure were deposited with PyC interlayer of about 150–200?nm, and then densified with SiC matrix by chemical vapor infiltration at 1050?°C or 1100?°C. The influence of preform structure and deposition temperature of SiC matrix on microstructure and ring compression properties of SiC_f/SiC composites tubes were evaluated, and the results showed that these factors have a significant influence on ring compression strength. The compressive strength of SiC_f/SiC composites with 2D plain weave structure and 2.5D shallow bend-joint structure are 377.75?MPa and 482.96?MPa respectively, which are significantly higher than that of the composites with 2D fiber wound structure (92.84?MPa). SiC_f/SiC composites deposited at 1100?°C looks like a more porous structure with SiC whiskers appeared when compared with the composites deposited at 1050?°C. Correspondingly, the ring compression strength of the composites deposited at 1100?°C (566.44?MPa) is higher than that of the composites deposited at 1050?°C (482.96?MPa), with a better fracture behavior. Finally, the fracture mechanism of SiC_f/SiC composites with O-ring shape was discussed in detail.     

Oxidation resistance and thermal cycling properties of the SiCnws–SiC coating on the C/SiC composites

SiC coatings reinforced with SiC nanowires were prepared on carbon/silicon carbide (C/SiC) composites through chemical vapor reaction route and chemical vapor deposition (CVD). The SiC nanowires were introduced to mainly improve the interface bonding properties of the coating and C/SiC composites. The microstructure, phase composition, thermal cycling, and bonding strength of the SiCnws–SiC coating were investigated. After nine thermal cycles, the weight loss of the SiCnws–SiC-coated C/SiC composites was only 4.6 wt.%. Tensile test results show that the tensile strength of the SiCnws–SiC-coated C/SiC composites was more than 4.5–4.6 MPa. The introduction of SiC nanowires effectively improved interface bonding strength, thus enhancing the thermal cycling and mechanical properties of the coating.     

Fabrication and properties of SiCnw-reinforced SiC composites by reactive melt infiltration with BN and PyC interface

To tailor the fiber–matrix interface of SiC nanowires-reinforced SiC (SiC_nw/SiC) ceramic matrix composites (CMCs) for improved mechanical properties, SiC nanowires were coated with BN and pyrolytic carbon (PyC) compound coatings prepared by the dip-coating process in boric acid and urea solution and the pyrolysis of phenolic resin. SiC_nw/SiC CMC with PyC/BN interfaces were fabricated by reactive melt infiltration (RMI) at 1680°C for 1 h. The influences of phenolic resin content on the microstructure and mechanical properties of the CMC were investigated. The results showed that the flexural strength and fracture toughness reach the maximum values of 294 MPa and 4.74 MPa m^1/2 as the phenolic resin content was 16 and 12 wt%, respectively. The displacement–load curve of the sample exhibited a gradient drop with increasing phenolic resin content up to 12 wt%. The results demonstrated that the PyC/BN compound coatings could play the role of protecting the SiC_nw from degradation as well as improving the more moderate interfacial bonding strengths during the RMI.     

High-temperature flexural strength of I-CVI processed Cf/SiC composites with variable interphases

The effect of single-layer pyrocarbon (PyC) and multilayered (PyC/SiC)_n=4 interphases on the flexural strength of un-coated and SiC seal-coated stitched 2D carbon fiber reinforced silicon carbide (C_f/SiC) composites was investigated. The composites were prepared by I-CVI process. Flexural strength of the composites was measured at 1200 °C in air atmosphere. It was observed that irrespective of the type of interphase, the seal coated samples showed a higher value of flexural strength as compared to the uncoated samples. The flexural strength of 470 ± 12 MPa was observed for the seal coated C_f/SiC composite samples with multilayered interphase. The seal coated samples with single layer PyC interphase showed flexural strength of 370 ± 20 MPa. The fractured surfaces of tested samples were analyzed in detail to study the fracture phenomena. Based on microstructure-property relations, a mechanism has been proposed for the increase of flexural properties of C_f/SiC composites having multilayered interphase.     

Improved thermal shock resistance of SiCnw/PyC core-shell structure-toughened CVD-SiC coating

In-situ SiC nanowire (SiCnw)/pyrolytic carbon (PyC) core-shell structures were introduced to mainly improve the thermal shock performance of chemical vapor deposition (CVD)-SiC coating on carbon/carbon (C/C) composites. The microstructure, phase composition, and mechanical properties of the CVD-SiC coating toughened by SiCnw/PyC core-shell structures were studied as well. The results show that the introduction of SiCnw/PyC core-shell structures can effectively alleviate the mismatch of coefficient of thermal expansion (CTE) between SiC coating and C/C substrate, thus enhancing the thermal shock resistance of the coating. Furthermore, the increased numbers of interfaces in the SiC coating owing to the addition of core-shell structures are beneficial to the mechanical properties of the coating after thermal shock test.     

界面类型对三维Nextel 720纤维增韧莫来石陶瓷基复合材料力学性能的影响

采用化学气相渗透工艺在Nextel 720纤维表面制备PyC和PyC／SiC两种涂层，然后以正硅酸乙酯和异丙醇铝作为先驱体，以先驱体浸渗热解法制备三维Nextd 720纤维增韧莫来石陶瓷基复合材料，比较分析了两种涂层复合材料的力学性能和断裂模式。结果表明：具预先涂覆PyC的复合材料中纤维与基体直接接触，发生烧结形成强结合界面，复合材料脆性断裂，三点抗弯强度仅56MPa。PyC／SiC涂层则演化为间隙／SiC复合界面层，SiC成为阻滞纤维与基体接触的阻挡层，间隙保证了纤维拔出，复合材料韧性断裂且三点抗弯强度高达267．2MPa。     

Microstructure and damage evolution of SiCf/PyC/SiC and SiCf/BN/SiC mini-composites: A synchrotron X-ray computed microtomography study

SiC_f/PyC/SiC and SiC_f/BN/SiC mini-composites comprising single tow SiC fibre-reinforced SiC with chemical vapor deposited PyC or BN interface layers are fabricated. The microstructure evolutions of the mini-composite samples as the oxidation temperature increases (oxidation at 1000, 1200, 1400, and 1600?°C in air for 2?h) are observed by scanning electron microscopy, energy dispersive spectrometry, and X-ray diffraction characterization methods. The damage evolution for each component of the as-fabricated SiC_f/SiC composites (SiC fibre, PyC/BN interface, SiC matrix, and mesophase) is mapped as a three-dimensional (3D) image and quantified with X-ray computed tomography. The mechanical performance of the composites is investigated via tensile tests.The results reveal that tensile failure occurs after the delamination and fibre pull-out in the SiC_f/PyC/SiC composites due to the volatilization of the PyC interface at high temperatures in the air environment. Meanwhile, the gaps between the fibres and matrix lead to rapid oxidation and crack propagation from the SiC matrix to SiC fibre, resulting in the failure of the SiC_f/PyC/SiC composites as the oxidation temperature increases to 1600?°C. On the other hand, the oxidation products of B₂O₃ molten compounds (reacted from the BN interface) fill up the fracture, cracks, and voids in the SiC matrix, providing excellent strength retention at elevated oxidation temperatures. Moreover, under the protection of B₂O₃, the SiC_f/BN/SiC mini-composites show a nearly intact microstructure of the SiC fibre, a low void growth rate from the matrix to fibre, and inhibition of new void formation and the SiO₂ grain growth from room to high temperatures. This work provides guidance for predicting the service life of SiC_f/PyC/SiC and SiC_f/BN/SiC composite materials, and is fundamental for establishing multiscale damage models on a local scale.     

Microstructure and properties of 2D-Cf/SiC composite fabricated by combination of CVI and PIP process with SiC particle as inert fillers

2D-C_f/SiC composite was manufactured by chemical vapor inflation (CVI) combined with polymer impregnation and pyrolysis (PIP) with SiC particle as inert fillers. The effects of CVI processes on SiC morphologies and the properties of composite were investigated. The composites were characterized by XRD, flexural strength test and SEM. The results revealed that uniform SiC coatings and nanowires were prepared when MTS/H₂ ratio of 1:8 was employed, while gradient thick coatings were fabricated as MTS/H₂ ratio of 1:1 was employed. The flexural strength of composites varied from 156 MPa at MTS/H₂ ratio of 1:1 to 233 MPa at MTS/H₂ ratio of 1:8. All of composites exhibited toughness due to significant debonding and pullout of fibers. The laminated structure of coatings on the fibers and nanowires were manufactured by combination of above different CVI process, and the obtained composites showed flexural strength of as high as 248 MPa and impressive toughness.