Protic ionic liquids for the selective absorption of H2S from CO2: Thermodynamic analysis

The solubilities of H₂S and CO₂ in four protic ionic liquids (PILs)—methyldiethanolammonium acetate, methyldiethanolammonium formate, dimethylethanolammonium acetate, and dimethylethanolammonium formate were determined at 303.2–333.2 K and 0–1.2 bar. It is shown PILs have higher absorption capacity for H₂S than normal ionic liquids (ILs) and the Henry's law constants of H₂S in PILs (3.5–11.5 bar at 303.2 K) are much lower than those in normal ILs. In contrast, the solubility of CO₂ in PILs is found to be a magnitude lower than that of H₂S, implying these PILs have both higher absorption capacity for H₂S and higher ideal selectivity of H₂S/CO₂ (8.9–19.5 at 303.2 K) in comparison with normal ILs. The behavior of H₂S and CO₂ absorption in PILs is further demonstrated based on thermodynamic analysis. The results illustrate that PILs are a kind of promising absorbents for the selective separation of H₂S/CO₂ and believed to have potential use in gas sweetening. © 2014 American Institute of Chemical Engineers AIChE J 60: 4232–4240, 2014     

Rigorous correlations for predicting the solubility of H2S in methylimidazolium-based ionic liquids

Two general and simple models, a group contribution correlation (model I) and an empirical relation (model II), were proposed to predict the solubility of H₂S in methylimidazolium based ionic liquids (ILs) over wide range of temperatures (303.15-363.15 K) and pressures (60.8-2016.8 kPa). The constants of the suggested functionality relations were found via the Nelder-Mead simplex algorithm. Both correlations were trained with 407 data points of H₂S solubility in 9 methylimidazolium based ILs and tested through 121 H₂S solubility data points of 3 different methylimidazolium based ILs to ensure generality. A comprehensive statistical evaluation showed that both suggested correlations are vigorous and have satisfactory error trends. The dataset was subjected to a statistical outlier diagnostic test and the validity of the database was confirmed. In addition, the sensitivity analysis revealed that the experimental data and both models have the same responses toward pressure and temperature, which indicates the reliability of the proposed correlations.     

Rheology of 1‐butyl‐3‐methylimidazolium chloride cellulose solutions. III. Elongational rheology

The elongational rheology of solutions of cellulose in the ionic liquid solvent 1‐butyl‐3‐methylimidazolium chloride ([Bmim]Cl) was measured at 80, 90, and 100°C; 8, 10, and 12 wt% cellulose; Hencky strains 5, 6, 7; and strain rates from 1 to 100 s^?1. Master curves were generated by shifting the elongational viscosity curves with respect to temperature and Hencky strain. Also, general master curves were generated by simultaneously shifting with respect to both temperatures and Hencky strain. From the Arrhenius plots of the temperature shift factors, the activation energy for elongational flow was determined. The elongational rheology of these solutions was elongational strain rate thinning similar to that of their shear behavior and polymer melts and they were also strain hardening. Both effects and the viscosity increased with cellulose concentration. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Hydrophobic protic ionic liquids tethered with tertiary amine group for highly efficient and selective absorption of H2S from CO2

Developing absorbents with both high absorption capacity of H₂S and large selectivity of H₂S/CO₂ is very important for natural gas sweetening process. To this end, a class of novel hydrophobic protic ionic liquids (ILs) containing free tertiary amine group as functional site for the absorption of H₂S were designed in this work. They were facilely synthesized through a simple neutralization‐metathesis methodology by utilizing diamine compounds and bis(trifluoromethylsulfonyl)imide as the building blocks for cation and anion, respectively. Impressively, the solubility of H₂S can reach 0.546 mol mol^?1 (1 bar) and 0.225 mol mol^?1 (0.1 bar), and the selectivity of H₂S/CO₂ can reach 37.2 (H₂S solubility at 1 bar vs. CO₂ solubility at 1 bar) and 15.4 (H₂S solubility at 0.1 bar vs. CO₂ solubility at 1 bar) in the hydrophobic protic ILs at 298.2 K. Comparing the hydrophobic protic ILs with other absorbents justifies their superior performance in the selective absorption of H₂S from CO₂. © 2016 American Institute of Chemical Engineers AIChE J, 62: 4480–4490, 2016     

Rheology of 1‐butyl‐3‐methylimidazolium chloride cellulose solutions. I. Shear rheology

In this article, shear rheology of solutions of different concentrations obtained by dissolution of cellulose in the ionic liquid (IL) solvent 1‐butyl‐3‐methylimidazolium chloride ([Bmim]Cl) was studied by measuring the complex viscosity and dynamic moduli at different temperatures. The obtained viscosity curves were compared with those of lyocell solutions and melt blowing grade polypropylene melts of different melt flow rates (MFR). Master curves were generated for complex viscosity and dynamic moduli by using Carreau and Cross viscosity models to fit experimental data. From the Arrhenius plots of the shift factors with respect to temperature, the activation energies for shear flow were determined. These varied between 18.99 and 24.09 kCal/mol, and were compared with values for lyocell solutions and different polymeric melts, such as polyolefins, polystyrene, and polycarbonate. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Antimicrobial properties and thermal stability of polycarbonate modified with 1‐alkyl‐3‐methylimidazolium tetrafluoroborate ionic liquids

Four water immiscible ionic liquids (ILs): 1‐hexyl‐3‐methylimidazolium tetrafluoroborate, 1‐heptyl‐3‐methylimidazolium tetrafluoroborate, 1‐octyl‐3‐methylimidazolium tetrafluoroborate and 1‐dodecyl‐3‐methylimidazolium tetrafluoroborate have been synthesized. Polycarbonate (PC) films containing ILs were prepared by solvent casting from methylene chloride solutions. Scanning electron microscopy measurements showed the high homogeneity of PC/IL films with the IL content up to 4 wt %. The tendency to IL aggregation was observed for polymeric films with higher IL content (5%). PC/IL composites were found to have the reduced thermal decomposition temperature under both an air and a nitrogen atmosphere in comparison with the neat PC. The effect of IL content on the antimicrobial activity of PC films against Escherichia coli bacteria was studied. Pronounced antimicrobial efficacy was revealed for PC/IL films for all studied ILs starting from 3 wt % of IL. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40050.     

Improved activity and stability of pseudomonas capaci lipase in a novel biocompatible ionic liquid, 1‐isobutyl‐3‐methylimidazolium hexafluorophosphate

BACKGROUND: Enzymes may exhibit enhanced activity, stability and selectivity in ionic liquids, depending on the properties of the liquid. The physical–chemical properties of ionic liquids, however, may be modified by altering the anion or cation in the ionic liquid. This feature is a key factor for realizing successful reactions. In this work, a new ionic liquid, 1‐isobutyl‐3‐methylimidazolium hexafluorophosphate (abbreviated as [i‐C₄mim][PF₆]), was synthesized and investigated as a novel medium for the transesterification reaction of 2‐phenylethanol with vinyl acetate catalyzed by pseudomonas capaci lipase. As contrasts, the reaction was also carried out in two reference solvents; the isomeric ionic liquid [i‐C₄mim][PF₆], 1‐butyl‐3‐methylimidazolium hexafluorophosphate (abbreviated as [C₄mim][PF₆]), and hexanes. RESULTS: As reaction medium, [i‐C₄mim][PF₆] was best among the three solvents. The initial reaction rate, the equilibrium conversion of 2‐phenylethanol and the half‐lifetime of the lipase in [i‐C₄mim][PF₆] medium were about 1.5, 1.2 and 3‐fold that obtained in [C₄mim][PF₆] medium, respectively. The lipase in [i‐C₄mim][PF₆] medium was recycled 10 times without substantial diminution in activity. CONCLUSION: The ionic liquid [i‐C₄mim][PF₆] has good biocompatibility, and can be used widely as green media in various biocatalysis reactions to improve the activity and stability of enzymes. Besides hydrophobicity and nucleophilicity, the spatial configuration of ionic liquids is also considered a key factor effecting the behaviour of the enzyme in ionic liquids. Copyright © 2008 Society of Chemical Industry     

An investigation into the degree and rate of polymerization of poly(methyl methacrylate) in the ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate

Room‐temperature ionic liquids (ILs), including 1‐butyl‐3‐methylimidazolium hexafluorophosphate, [bmim⁺][PF₆^?], were investigated as replacements for volatile organic compounds in the free‐radical solution polymerization of poly(methyl methacrylate) (PMMA). The latter was synthesized in benzene and [bmim⁺][PF₆^?] at 70 °C via a free‐radical process and the degree and rate of polymerization were compared based on the solvent used. The degree of polymerization was found to be five times higher in [bmim⁺][PF₆^?] than in benzene, while the rate of reaction was approximately four times faster in [bmim⁺][PF₆^?]. The results indicate the potential for using ILs to produce high‐molecular‐weight polymers and block structures based on the increased free‐radical stability in ILs. Copyright © 2004 Society of Chemical Industry     

1‐Allyl‐3‐methylimidazolium halometallate ionic liquids as efficient catalysts for the glycolysis of poly(ethylene terephthalate)

Series of 1‐allyl‐3‐methylimidazolium halometallate ionic liquids (ILs) were synthesized and used to degrade poly(ethylene terephthalate) (PET) as catalysts in the solvent of ethylene glycol. One important feature of these new IL catalysts is that most of them, especially [amim][CoCl₃] and [amim][ZnCl₃], exhibit higher catalytic activity under mild reaction condition, compared to the traditional catalysts [e.g., Zn(Ac)₂], the conventional IL catalysts (e.g., [bmim]Cl), Fe‐containing magnetic IL catalysts (e.g., [bmim][FeCl₄]), and metallic acetate IL catalysts (e.g., [Deim][Zn(OAc)₃]). For example, using [amim][ZnCl₃] as catalyst, the conversion of PET and the selectivity of bis(hydroxyethyl) terephthalate (BHET) reach up to 100% and 80.1%, respectively, under atmospheric pressure at 175°C for only 1.25 h. Another important feature is that BHET can be easily separated from the catalyst and has a high purity. Finally, based on the experimental phenomena, in ‐situ infrared spectra, and experimental results, the possible mechanism of degradation with synthesized IL is proposed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Rheological characterization of concentrated cellulose solutions in 1‐allyl‐3‐methylimidazolium chloride

The rheological properties of high concentrated wood pulp cellulose 1‐allyl‐3‐methy‐limidazolium Chloride ([Amim]Cl) solutions were investigated by using steady shear and dynamic viscoelastic measurement in a large range of concentrations (10–25 wt %). The measurement reveals that cellulose may slightly degrade at 110°C in [Amim]Cl and the Cox–Merz rule is valid for 10 wt % cellulose solution. All of the cellulose solutions showed a shear thinning behavior over the shear rate at temperature from 80 to 120°C. The zero shear viscosity (η_o) was obtained by using the simplified Cross model to fit experimental data. The η_o values were used for detailed viscosity‐concentration and activation energy analysis. The exponent in the viscosity‐concentration power law was found to be 3.63 at 80°C, which is comparable with cellulose dissolved in other solvents, and to be 5.14 at 120°C. The activation energy of the cellulose solution dropped from 70.41 to 30.54 kJ/mol with an increase of concentration from 10 to 25 wt %. The effects of temperature and concentration on the storage modulus (G′), the loss modulus (G″) and the first normal stress difference (N₁) were also analyzed in this study. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Cuprous-based composite ionic liquids for the selective absorption of CO: Experimental study and thermodynamic analysis

Three cuprous-based composite ionic liquids (ILs) [EimH][OAc]–xCuOAc (x = 0.5, 0.6, 0.7) were prepared and employed for efficient absorption of CO. It is shown that the cuprous composite IL [EimH][OAc]–0.6CuOAc exhibited the largest absorption capacity for CO (0.031 g/g at 293.15 K and 1 bar) and had a record CO/N₂ selectivity of 967, which is better than most of common ILs and solvents reported in the literature. The results of Fourier transform infrared (FTIR) spectra, electrospray ionization mass spectrometry (ESI-MS) analysis, and theoretical calculations reveal that such superior CO capacity mainly resulted from two kinds of chemical interaction between CO and the active anionic species [Cu(OAc)₂]⁻ in [EimH][OAc]–0.6CuOAc. Furthermore, a “deactivated IL model” was further proposed to accurately describe the absorption behavior of CO in [EimH][OAc]–0.6CuOAc, in which the thermodynamic parameters including Henry's law constants, reaction equilibrium constants, and absorption enthalpies were estimated by the correlation of the experimental solubilities of CO.     

Evaluation of 1‐ethyl‐3‐methylimidazolium acetate based ionic liquid systems as a suitable solvent for collagen

Collagen, a prominent biopolymer, which is famous for its excellent biological activity, has been used extensively for tissue engineering applications. In this study, a novel solvent system for collagen was developed with an ionic liquid, 1‐ethyl‐3‐methylimidazolium acetate ([EMIM][Ac]), solvent system. A series of sodium salts were introduced into this solvent system to enhance collagen's dissolution procedure. The results show that the solubility of collagen was significantly influenced by the temperature and sodium salts. The solubility reached up to approximately 11% in the [EMIM][Ac]/Na₂HPO₄ system at 45°C. However, the structure of the regenerated collagen (Col‐regenerated) may have been damaged. Hence, we focused on the structural integrity of the collagen regenerated from the [EMIM][Ac] solvent system by the methods of sodium dodecyl sulfate–polyacrylamide gel electrophoresis, Fourier transform infrared spectroscopy, ultrasensitive differential scanning calorimetry, atomic force microscopy, X‐ray diffraction, and circular dichroism because its signature biological and physicochemical properties were based on its structural integrity. Meanwhile, a possible dissolution mechanism was proposed. The results show that the triple‐helical structure of collagen regenerated from the [EMIM][Ac] solvent system below 35°C was retained to a large extent. The biocompatibility of Col‐regenerated was first characterized with a fibroblast adhesion and proliferation model. It showed that the Col‐regenerated had almost the same good biological activity as nature collagen, and this indicated the potential application of [EMIM][Ac] in tissue engineering. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2245–2256, 2013     

Gas–liquid mass‐transfer properties in CO2 absorption system with ionic liquids

The deficiency of mass‐transfer properties in ionic liquids (ILs) has become a bottleneck in developing the novel IL‐based CO₂ capture processes. In this study, the liquid‐side mass‐transfer coefficients (k_L) were measured systematically in a stirred cell reactor by the decreasing pressure method at temperatures ranging from 303 to 323 K and over a wide range of IL concentrations from 0 to 100 wt %. Based on the data of k_L, the kinetics of chemical absorption of CO₂ with mixed solvents containing 30 wt % monoethanolamine (MEA) and 0–70 wt % ILs were investigated. The k_L in IL systems is influenced not only by the viscosity but also the molecular structures of ILs. The enhancement factors and the reaction activation energy were quantified. Considering both the mass‐transfer rates and the stability of IL in CO₂ absorption system, the new IL‐based system MEA + [bmim][NO₃] + H₂O is recommended. © 2014 American Institute of Chemical Engineers AIChE J, 60: 2929–2939, 2014     

Transition Metal‐Free Synthesis of 3‐Alkynylpyrrole‐2‐carboxylates via Michael Addition/Intramolecular Cyclodehydration

A transition metal‐free and efficient method for the synthesis of 3‐alkynylpyrrole‐2‐carboxylates from diynones and glycine esters or 2‐aminoacetophenone hydrochloride has been developed. This transformation provides a large range of substituted pyrroles in good to excellent yields with the elimination of water as the only by‐product. The detailed mechanistic studies elucidated that this transformation involves a Michael addition/intramolecular cyclodehydration process.

     

A Simple Copper‐Catalyzed Cascade Synthesis of 2‐Amino‐1H‐indole‐3‐carboxylate Derivatives

We have developed a simple and efficient copper‐catalyzed method for the synthesis of 2‐amino‐1H‐indole‐3‐carboxylate derivatives via cascade reactions of substituted N‐(2‐halophenyl)‐2,2,2‐trifluoroacetamide with alkyl 2‐cyanoacetate or malononitrile under mild conditions, and the method is of wide practical application.     

Dissolution and utilization of chitosan in a 1‐carboxymethyl‐3‐methylimidazolium hydrochloride ionic salt aqueous solution

1‐Carboxymethyl‐3‐methylimidazolium hydrochloride ([IMIM–COOH]Cl), a new ionic salt, is proposed as a green, promising solvent for dissolving chitosan. However, because of the optimal dosage of chitosan dissolved in [IMIM–COOH]Cl, a 12 wt % [IMIM–COOH]Cl aqueous solution was selected as an optimum solvent system for dissolving chitosan. The structures of the original and regenerated chitosan were characterized by Fourier transform infrared spectroscopy and X‐ray diffraction analysis. Scanning electron microscopy was used to visualize the morphological features of the reconstituted chitosan membranes. Meanwhile, the absorbance, tensile strength, and breaking elongation of the chitosan membranes were measured. The results reveal that 10–11 wt % was an optimal chitosan concentration for preparing membranes. Furthermore, the adsorption capacity for Cu(II) ion of the chitosan membranes was increased with the chitosan concentration decreased from 12 to 8 wt %. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41965.     

Michael Reaction of Nitroalkanes with β‐Nitroacrylates under a Solid Promoter: Advanced Regio‐ and Diastereoselective Synthesis of Nitro‐Functionalized α,β‐Unsaturated Esters and 1,3‐Butadiene‐2‐carboxylates

A new class of nitro‐functionalized α,β‐unsaturated esters has been prepared by a regio‐ and diastereoselective Michael addition of nitroalkanes to β‐nitroacrylates, performed at room temperature, under carbonate on polymer as promoter, and in the presence of ethyl acetate as eco‐friendly solvent. Moreover, by the modular choice of the reaction conditions the method allows the synthesis of 1,3‐butadiene‐2‐carboxylates.     

Molecularly imprinted polymers for the selective recognition of l‐phenylalanine based on 1‐buty‐3‐methylimidazolium ionic liquid

To enhance the affinity of 4‐vinyl pyridine to l ‐phenylalanine (l ‐Phe) and convert the imprinting process from the aqueous phase to the organic phase, an oil‐soluble amino acid ionic liquid was introduced as a template. In this study, 1‐butyl‐3‐methylimidazolium α‐aminohydrocinnamic acid salt was first applied to prepared surface molecularly imprinted polymers (MIPs) in acetonitrile for the selective recognition of l ‐Phe. Fluorescence quenching analysis of the functional monomer on the template was investigated under different conditions to study the imprinting mechanism. Several binding studies, such as the sorption kinetics, sorption thermodynamics, and solid‐phase extraction application, and the chiral resolution of racemic phenylalanine were investigated. The binding isotherms were fitted by nonlinear regression to the Freundlich model to investigate the recognition mechanism. The affinity distribution analysis revealed that polymers imprinted by ionic liquid showed higher homogeneous binding sites than those imprinted by l ‐Phe. The competition tests were conducted by a molecularly imprinting solid‐phase extraction procedure to estimate the selective separation properties of the MIPs for l ‐Phe. The target MIP was shown to be successfully for the separation of l ‐Phe from an amino acid mixture. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42485.