Production of biodiesel from wet activated sludge

BACKGROUND: The production of biodiesel from activated sludge obtained from Tuscaloosa, AL was optimized based on the yield of fatty acid methyl esters (FAMEs) using an in situ transesterification process. An orthogonal central composite response surface design was considered to investigate the main and interaction effects of temperature, methanol to sludge ratio, and catalyst concentration. RESULTS: The biodiesel yield can be satisfactorily described by the quadratic response surface model with R² of 0.836 and a statistically not significant lack of fit (p = 0.254). Coded regression coefficients, main effect plots and surface plots indicated that maximum biodiesel yield may be obtained at 75 °C, 30 mL g^?1 (methanol/sludge) and 10% volume (catalyst concentration). Numerical optimization showed that at this reaction condition, a biodiesel yield of 3.78% (weight) can be obtained. Experimental verification gave a biodiesel yield of 3.93 ± 0.15% (weight) giving a model error of 7.35%. This indicates high reliability of the model. CONCLUSIONS: The economic analysis showed that the in situ transesterification of wet activated sludge (84.5% weight moisture) is less economical than the in situ transesterification of dried sludge (5% weight moisture). However, sensitivity analysis indicated that the process can be made more economical by reduction of water to 50% (weight). At this level of moisture, a biodiesel break‐even price of around $7.00 per gallon is attainable, which is still more expensive than petroleum‐based diesel (～$2.95 per gallon). For the biodiesel from activated sludge to be economically competitive, a biodiesel yield of at least 10% (weight) is necessary. Copyright © 2010 Society of Chemical Industry     

Biodiesel from activated sludge through in situ transesterification

BACKGROUND: The microbial biomass present in activated sludge contains lipidic compounds that can be used as biodiesel feedstock. In this study, the production of biodiesel from activated sludge from Tuscaloosa, AL was optimized based on the yield of fatty acid methyl esters (FAMEs). In situ transesterification was used with sulfuric acid as catalyst. A general factorial design of 4 × 6 × 5 for temperature, methanol to sludge ratio and catalyst concentration, respectively, was considered for optimization. RESULTS: Biodiesel yield can be adequately described by the quadratic response surface model with R² of 0.843 and statistically insignificant lack of fit (p = 0.152). Numerical optimization showed that an optimum biodiesel yield of 4.88% can be obtained at 55 °C, 25 methanol to sludge ratio and 4% volume sulfuric acid. The optimum experimental biodiesel yield was indeed obtained at that condition but with a value of 4.79 ± 0.02%. The highest error was 2.30% which indicates good agreement between the model and the experimental data. CONCLUSIONS: Acid‐catalyzed polymerization of unsaturated fatty acids or their esters at temperature above 60 °C significantly decreased biodiesel yield. The fatty acid profile of the biodiesel produced indicates that activated sludge may be used as biodiesel feedstock. Copyright © 2009 Society of Chemical Industry     

Acid base catalyzed transesterification kinetics of waste cooking oil

The present study reports the results of kinetics study of acid base catalyzed two step transesterification process of waste cooking oil, carried out at pre-determined optimum temperature of 65 °C and 50 °C for esterification and transesterification process respectively under the optimum condition of methanol to oil ratio of 3:7 (v/v), catalyst concentration 1%(w/w) for H₂SO₄ and NaOH and 400 rpm of stirring. The optimum temperature was determined based on the yield of ME at different temperature. Simply, the optimum concentration of H₂SO₄ and NaOH was determined with respect to ME Yield. The results indicated that both esterification and transesterification reaction are of first order rate reaction with reaction rate constant of 0.0031 min^− 1 and 0.0078 min^− 1 respectively showing that the former is a slower process than the later. The maximum yield of 21.50% of ME during esterification and 90.6% from transesterification of pretreated WCO has been obtained. This is the first study of its kind which deals with simplified kinetics of two step acid-base catalyzed transesterification process carried under the above optimum conditions and took about 6 h for complete conversion of TG to ME with least amount of activation energy. Also various parameters related to experiments are optimized with respect to ME yield.     

Feasibility of Palm Oil as the Feedstock for Biodiesel Production via Heterogeneous Transesterification

The production of biodiesel has become popular recently as a result of increasing demand for a clean, safe and renewable energy. Biodiesel is made from natural renewable sources such as vegetable oils and animal fats. The conventional method of producing biodiesel is by reacting vegetable oil with alcohol in the presence of a homogenous catalyst (NaOH). However, this conventional method has some limitations such as the formation of soap, usage of significant quantities of wash water and complicated separation processes. Heterogeneous processes using solid catalysts have significant advantages over homogenous methods. Currently, more than 90 % of world biodiesel is produced using rapeseed oil. The production of biodiesel from rapeseed oil is considered uneconomical, considering the fact that palm oil is currently the world's cheapest vegetable oil. Therefore, the focus of this study is to show the feasibility of producing biodiesel from palm oil using montmorillonite KSF as a heterogeneous catalyst. The heterogeneous transesterification process was studied using design of experiment (DOE), specifically response surface methodology (RSM) based on a four‐variable central composite design (CCD) with α = 2. The transesterification process variables were reaction temperature, x₁ (50–190 °C), reaction period, x₂ (60–300 min), methanol/oil ratio, x₃ (4–12 mol mol^–1) and the amount of catalyst, x₄ (1–5 wt %). It was found that the conversion of palm oil to biodiesel can reach up to 78.7 % using the following reaction conditions: reaction temperature of 155 °C, reaction period of 120 min, ratio of methanol/oil at 10:1 mol mol^–1 and amount of catalyst at 4 wt %. From this study, it was shown that montmorillonite KSF catalyst can be used as a solid catalyst for biodiesel production from palm oil.     

Biodiesel synthesis via homogeneous Lewis acid-catalyzed transesterification

Lewis acids (AlCl₃ or ZnCl₂) were used to catalyze the transesterification of canola oil with methanol in the presence of terahydrofuran (THF) as co-solvent. The conversion of canola oil into fatty acid methyl esters was monitored by ¹H NMR. NMR analysis demonstrated that AlCl₃ catalyzes both the esterification of long chain fatty acid and the transesterification of vegetable oil with methanol suggesting that the catalyst is suitable for the preparation of biodiesel from vegetable oil containing high amounts of free fatty acids. Optimization by statistical analysis showed that the conversion of triglycerides into fatty acid methyl esters using AlCl₃ as catalyst was affected by reaction time, methanol to oil molar ratio, temperature and the presence of THF as co-solvent. The optimum conditions with AlCl₃ that achieved 98% conversion were 24:1 molar ratio at 110 °C and 18 h reaction time with THF as co-solvent. The presence of THF minimized the mass transfer problem normally encountered in heterogeneous systems. ZnCl₂ was far less effective as a catalyst compared to AlCl₃, which was attributed to its lesser acidity. Nevertheless, statistical analysis showed that the conversion with the use of ZnCl₂ differs only with reaction time but not with molar ratio.     

Synthesis of economically viable biodiesel from waste frying oils (WFO)

In present communication, waste frying oil (WFO) has been used as a feedstock for biodiesel synthesis. WFO, procured from a local Indian restaurant possessed an acid value of 0.84 mg KOH/g, which is low enough for single step transesterification reaction. Biodiesel (fatty acid methyl esters) was washed after transesterification reaction and the yield got lowered substantially (from 96% to 86.36%) after water washing owing to loss of esters. 30:100 vol% (methanol to oil), 0.6 wt% NaOCH₃, 60°C temperature and 600 rpm agitation in 1 h reaction time was found to be optimum for transesterification reaction. ¹H NMR spectrum showed a high conversion (95.19%) of fatty acids in WFO to biodiesel in 2 h reaction time. Almost complete conversion (99.68%) was attained in 2 h reaction time. © 2011 Canadian Society for Chemical Engineering     

Optimization of biodiesel production from crude palm oil using ultrasonic irradiation assistance and response surface methodology

BACKGROUND: Production of biodiesel from crude palm oil (CPO) with 6 wt% of free fatty acid (FFA) using a low‐frequency ultrasonic irradiation (40 kHz) technique was investigated in the present work. The objective of this study was to determine the relationship between various important parameters of the alkaline catalyzed transesterification process to obtain a high conversion to biodiesel. Response surface methodology (RSM) was used to statistically analyze and optimize the operating parameters of the process. A central composite design (CCD) was adopted to study the effects of the methanol to oil molar ratio, the catalyst concentration, reaction temperature, and irradiation time on conversion to biodiesel. RESULTS: The result from the RSM analysis indicated that the methanol to oil molar ratio, catalyst concentration and irradiation time have the most significant effects on the conversion to biodiesel. Moreover, a coefficient of determination (R²) value of 0.93 shows the fitness of a second‐order model for the present study. Based on this second‐order model, the optimum conditions for alkaline catalyzed transesterification of CPO were found to be a methanol to oil molar ratio of 6.44:1, catalyst concentration 1.25 wt%, reaction temperature 38.44 °C and irradiation time 25.96 min. At the calculated optimum condition, the conversion to biodiesel reached 97.85%. Under these same conditions, the experimental value was 98.02 ± 0.6%. CONCLUSIONS: The mathematical model developed has been proven to adequately describe the range of the experimental parameters studied and provide a statistically accurate prediction of the optimum conversion to biodiesel. Copyright © 2011 Society of Chemical Industry     

Kinetics of methyl ester production from mixed crude palm oil by using acid-alkali catalyst

The production of biodiesel from high free fatty acid mixed crude palm oil using a two-stage process was investigated. The kinetics of the reactions was determined in a batch reactor at various reaction temperatures. It was found that the optimum conditions for reducing high free fatty acid (FFA) in MCPO (8-12 wt.%/wt oil) using esterification was a 10:1 molar ratio of methanol to FFA and using 10 wt.%/wt of sulfuric acid (based on FFA) as catalyst. The subsequent transesterification reaction to convert triglycerides to the methyl ester was found to be optimal using 6:1 molar ratio of methanol to the triglyceride (TG) in MCPO and using 0.6 wt.%/vol_TG sodium hydroxide as catalyst. Both reactions were carried out in a stirred batch reactor over a period of 20 min at 55, 60 and 65 °C. The concentration of compounds in each sample was analyzed by Thin Layer Chromatography/Flame Ionization Detector (TLC/FID), Karl Fischer, and titration techniques. The results were used for calculating the rate coefficients by using the curve-fitting tool of MATLAB. Optimal reaction rate coefficients for the forward and reverse esterification reactions of FFA were 1.340 and 0.682 l mol⁻¹ min⁻¹, respectively. The corresponding optimal transesterification, rate coefficients for the forward reactions of TG, diglyceride (DG), and monoglyceride (MG) of transesterification were 2.600, 1.186, and 2.303 l mol⁻¹ min⁻¹, and for the reverse reactions were 0.248, 0.227, and 0.022 l mol⁻¹ min⁻¹, respectively.     

In situ production of fatty acid methyl ester from low quality rice bran: An economical route for biodiesel production

Low quality rice bran was used to produce fatty acid methyl ester (FAME) via in situ extraction, esterification and transesterification process. The effects of the acid and alkaline catalysts on the ester yield, esterification and transesterification process were studied. When 75 ml of absolute methanol, 150 ml of petroleum ether, 0.75 g of concentrated sulfuric acid and 0.71 g of sodium hydroxyl were used, 16.69% (w_FAME/w_{rice bran}) of FAME was obtained. The esterification rate and the transesterification rate reached 98.83% and 80.47%. Based on the proposed route, the production process of FAME (biodiesel) could be simplified and the production cost could be reduced.     

Biodiesel production by direct methanolysis of oleaginous microbial biomass

Biodiesel is a renewable fuel conventionally prepared by transesterification of pre‐extracted vegetable oils and animal fats of all resources with methanol, catalyzed by strong acids or bases. This paper reports on a novel biodiesel production method that features acid‐promoted direct methanolysis of cellular biomass of oleaginous yeasts and filamentous fungi. The process was optimized for tuning operation parameters, such as methanol dosage, catalyst concentration, reaction temperature and time. Up to 98% yield was reached with reaction conditions of 70 °C, under ambient pressure for 20 h and a dried biomass to methanol ratio 1:20 (w/v) catalyzed by either 0.2 mol L^?1 H₂SO₄ or 0.4 mol L^?1 HCl. Cetane numbers for these products were estimated to range from 56 to 59. This integrated method is thus effective and technically attractive, as dried microbial biomass as feedstocks omits otherwise tedious and time‐consuming oil extraction processes. Copyright © 2007 Society of Chemical Industry     

两步法催化高酸价微藻油脂制备生物柴油

研究了两步法催化高酸价微藻油脂制备生物柴油的工艺条件。测定从产油栅藻培养物中提取的油脂的化学成分,发现油脂的游离脂肪酸含量分布在10%~32%,极性脂含量分布在21%~46%。以此高酸价、高极性脂含量油脂,经过酸预酯化-碱催化转酯化两步法制备生物柴油。其最优反应条件为:30%的醇加入量,1%油质量的硫酸催化反应2 h,其油脂酸价可从初始酸值的17~46 mg/g降低至2 mg/g以下;随后,在醇油物质的量之比为12:1,催化剂氢氧化钾用量为油质量的2%,65℃条件下反应30min,制备所得生物柴油中脂肪酸甲酯的质量分数可达96.6%,甘油三酯的转化效率接近100%。根据《柴油机燃料调合用生物柴油》国家标准,测定了微藻生物柴油产品的品质指标,发现其密度、运动黏度、酸价、氧化安定性等各项指标均符合国家标准(GB/T 20828-2007);热值为39.76 MJ/kg,符合欧盟生物柴油标准(EN 14214)。     

Calcium oxide as a solid base catalyst for transesterification of soybean oil and its application to biodiesel production

In order to study solid base catalyst for biodiesel production with environmental benignity, transesterification of edible soybean oil with refluxing methanol was carried out in the presence of calcium oxide (CaO), -hydroxide (Ca(OH)₂), or -carbonate (CaCO₃). At 1 h of reaction time, yield of FAME was 93% for CaO, 12% for Ca(OH)₂, and 0% for CaCO₃. Under the same reacting condition, sodium hydroxide with the homogeneous catalysis brought about the complete conversion into FAME. Also, CaO was used for the further tests transesterifying waste cooking oil (WCO) with acid value of 5.1 mg-KOH/g. The yield of FAME was above 99% at 2 h of reaction time, but a portion of catalyst changed into calcium soap by reacting with free fatty acids included in WCO at initial stage of the transesterification. Owing to the neutralizing reaction of the catalyst, concentration of calcium in FAME increased from 187 ppm to 3065 ppm. By processing WCO at reflux of methanol in the presence of cation-exchange resin, only the free fatty acids could be converted into FAME. The transesterification of the processed WCO with acid value of 0.3 mg-KOH/g resulted in the production of FAME including calcium of 565 ppm.     

RETRACTED ARTICLE: Optimization of Biodiesel Production Using a Magnetically Stabilized Fluidized Bed Reactor

A biodiesel production process using magnetically stabilized fluidized bed reactor (MSFBR) has been developed based on the refined cottonseed oil. The reactant flow rate and magnetic field intensity effects on the nanometer magnetic catalyst behavior in the column were investigated. Orthogonal experiments (L₄(2)³) were applied to optimize the best transesterification reaction conditions. Reaction temperature, methanol to oil molar ratio, and reactant flow rate were the main factors to influence transesterification conversion efficiency. These three factors chosen for the present investigation were based on the results of single-factor tests. The optimum transesterification reaction conditions of cottonseed oil were determined in MSFBR as follows: methanol to oil molar ratio 8:1, 40 cm³ min⁻¹ reactant flow rate, 225 Oe magnetic field intensity and reaction temperature of 65 °C, the conversion efficiency reached 97% in 100 min. The cold filter plugging point and kinematic viscosity of cottonseed oil biodiesel were higher than that described by Chinese specifications of biodiesel because of the special fatty acid profiles of cottonseed oil. The activity stability of the nanometer magnetic solid catalyst in MSFBR was much better than that in the autoclave stirred reactor (ASR).     

Producing biodiesel from high free fatty acids waste cooking oil assisted by radio frequency heating

Efficient biodiesel conversion from waste cooking oil with high free fatty acids (FFAs) was achieved via a two-stage procedure (an acid-catalyzed esterification followed by an alkali-catalyzed transesterification) assisted by radio frequency (RF) heating. In the first stage, with only 8-min RF heating the acid number of the waste cooking oil was reduced from 68.2 to 1.64 mg KOH/g by reacting with 3.0% H₂SO₄ (w/w, based on oil) and 0.8:1 methanol (weight ratio to waste oil). Then, in the second stage, the esterification product (primarily consisting of triglycerides and fatty acid methyl esters) reacted with 0.91% NaOH (w/w, based on triglycerides) and 14.2:1 methanol (molar ratio to triglycerides) under RF heating for 5 min, and an overall conversion rate of 98.8 ± 0.1% was achieved. Response surface methodology was employed to evaluate the effects of RF heating time, H₂SO₄ dose and methanol/oil weight ratio on the acid-catalyzed esterification. A significant positive interaction between RF heating time and H₂SO₄ concentration on the esterification was observed.     

A Transesterification Double Step Process — TDSP for biodiesel preparation from fatty acids triglycerides

This study introduces a two consecutive steps basic–acid transesterification process, (denominated Transesterification Double Step Process — TDSP) for biodiesel production from vegetable oils. The process involves homogeneous consecutive basic–acid catalysis steps and is characterized by formation of well-defined phases, easy separation procedures, high reaction velocity and high conversion efficiency. The proposed TDSP is different in relation to other traditional two-step procedures which normally include acid esterification followed by basic transesterification, or enzymatic or even supercritical transesterification conditions. The biodiesel (fatty acid methyl esters) was analyzed by standard biodiesel techniques in addition to ¹H-NMR, indicating high quality and purity biodiesel products. The transesterification of sunflower and linseed oils resulted in oil conversions higher than 97% corresponding to yields of 85%. A probable reaction mechanism responsible for the process is presented.     

Transesterification double step process modification for ethyl ester biodiesel production from vegetable and waste oils

In this study, the transesterification double step process (TDSP) was modified to enable the usage of ethanol as a transesterification agent in the production of biodiesel from vegetable and waste oils. The TDSP comprises a two-step transesterification procedure, which is initiated by a homogeneous basic catalysis step and followed by an acidic catalysis step. To optimize the transesterification parameters, different reaction mixtures and conditions were tested. Compared with methanol transesterification, larger ethanol and catalyst amounts as well as higher reaction times and temperatures were required. However, the results were consistent with those usually reported for ethanol transesterification. The obtained biodiesels (i.e., fatty acid ethyl esters (FAEEs)) were analyzed by standard physico-chemical techniques in addition to ¹H NMR, ¹³C NMR and FTIR spectroscopies, indicating high quality and purity biodiesel products. The obtained conversions were evaluated by ¹H NMR spectroscopy. For the optimized process, the triglyceride conversion to biodiesel was ?97% for all oils used. The overall process yields are considerably high when compared to the single basic catalysis yields.     

Study of the acid pretreatment and biodiesel production from olive pomace oil

The objective of this work was to study the two‐step acid base homogenous catalyzed transesterification of olive pomace oil, with the ultimate purpose of producing biodiesel under mild reaction conditions by optimizing the process. Optimization of the experimental procedure was conducted by a factorial design of 2³ under the acidic pretreatment step and during the basic transesterification. The optimal production of methyl esters (97.8%) was achieved for the experimental conditions H₂SO₄ = 20 wt%/CH₃OH = 35:1/T = 40^°C and KOH = 0.6+ fatty acid value /CH₃OH = 9:1/ T = 60^°C, in the acidic and basic stage of the process, respectively. Finally, to properly assess the quality of the biofuel produced, it was tested for all the European Standard properties.     

CO2 process intensification of algae oil extraction to biodiesel

Algae-to-biodiesel processes are hindered by high costs and low energy return on investment.^1,2. Herein, three foci in research improve algae-to-biodiesel processes by: (1) reducing high installation and energy costs in the CO₂ sequestration, cultivation, and harvesting stages; (2) improving oil extraction and biodiesel generation; and (3) increasing utilization of the proteins in lipid-extracted biomass (e.g., for animal feed), as well as the omega-3 fatty acids for nutraceuticals and food supplements. A process is introduced that uses carbon dioxide to aid in all three of these foci. CO₂ is used first in the form of microbubbles to lyse algae cell walls, releasing triglyceride oils. CO₂ also aids with transesterification of these triglycerides using methanol. At low temperatures (353.15–368.15 K) and intermediate pressures (5–10 MMPa), carbon dioxide causes methanol to dissolve partially in the triglyceride phase and triglyceride to dissolve partially in the methanol phase, increasing the transesterification reaction rate. Due to the nondestructive nature of these processes, other metabolites can also be harvested providing improvements in both mass and economic efficiency with an overall sharp reduction in the modeled price of biodiesel.     

Biodiesel Production from Soybean Oil Catalyzed by Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>

In the present study, we synthesized biodiesel from soybean oil through a transesterification reaction catalyzed by lithium carbonate. Under the optimal reaction conditions of methanol/oil molar ratio 32:1, 12 % (wt/wt oil) catalyst amount, and a reaction temperature of 65 °C for 2 h, there was a 97.2 % conversion to biodiesel from soybean oil. The present study also evaluated the effects of methanol/oil ratio, catalyst amount, and reaction time on conversion. The catalytic activity of solid base catalysts was insensitive to exposure to air prior to use in the transesterification reaction. Results from ICP-OES exhibited non-significant leaching of the Li₂CO₃ active species into the reaction medium, and reusability of the catalyst was tested successfully in ten subsequent cycles. Free fatty acid in the feedstock for biodiesel production should not be higher than 0.12 % to afford a product that passes the EN biodiesel standard. Product quality, ester content, free glycerol, total glycerol, density, flash point, sulfur content, kinematic viscosity, copper corrosion, cetane number, iodine value, and acid value fulfilled ASTM and EN standards. Commercially available Li₂CO₃ is suitable for direct use in biodiesel production without further drying or thermal pretreatment, avoiding the usual solid catalyst need for activation at high temperature.     

Biolubricant Production of 2‐Ethylhexyl Palmitate by Transesterification Over Unsupported Potassium Carbonate

Owing to the decrease of global oil price, development of downstream value‐added products is important to biodiesel industry. In this study, we used palmitic acid methyl ester (PAME) as a starting material to produce 2‐ethylhexyl palmitate (2‐EHP), an environmentally friendly biolubricant product, which was derived from the transesterification of fatty acid methyl esters and long chain fatty alcohols. Conventional synthetic routes of 2‐EHP have disadvantages, including high catalyst price, low conversion efficiency, and pollution issues. To solve these problems, in situ transesterification of PAME with 2‐ethylhexanol (2‐EH) was conducted over unsupported potassium carbonate as heterogeneous catalyst. The optimal reaction temperature, 2‐EH to PAME molar ratio, and catalyst to PAME mass ratio were 180 °C, 3:1, and 3.0 wt%, respectively. The PAME conversion reached up to 100% within 1 hour under the optimal conditions. In addition, a kinetic model describing the experimental data over a temperature range of 160–180 °C was developed. The dependence of kinetic rate constant (k) on temperature was evaluated, and the activation energy (E_a) for the transesterification of PAME with 2‐EH was calculated to be 57.04 kJ mol^?1.