Porous Organic Field‐Effect Transistors for Enhanced Chemical Sensing Performances

The thin‐film structures of chemical sensors based on conventional organic field‐effect transistors (OFETs) can limit the sensitivity of the devices toward chemical vapors, because charge carriers in OFETs are usually concentrated within a few molecular layers at the bottom of the organic semiconductor (OSC) film near the dielectric/semiconductor interface. Chemical vapor molecules have to diffuse through the OSC films before they can interact with charge carriers in the OFET conduction channel. It has been demonstrated that OFET ammonia sensors with porous OSC films can be fabricated by a simple vacuum freeze‐drying template method. The resulted devices can have ammonia sensitivity not only much higher than the pristine OFETs with thin‐film structure but also better than any previously reported OFET sensors, to the best of our knowledge. The porous OFETs show a relative sensitivity as high as 340% ppm^?1 upon exposure to 10 parts per billion (ppb) NH₃. In addition, the devices also exhibit decent selectivity and stability. This general and simple strategy can be applied to a wide range of OFET chemical sensors to improve the device sensitivity.     

Hydrocarbons‐Driven Crystallization of Polymer Semiconductors for Low‐Temperature Fabrication of High‐Performance Organic Field‐Effect Transistors

While many high‐performance polymer semiconductors are reported for organic field‐effect transistors (OFETs), most require a high‐temperature postdeposition annealing of channel semiconductors to achieve high performance. This negates the fundamental attribute of OFETs being a low‐cost alternative to conventional high‐cost silicon technologies. A facile solution process is developed through which high‐performance OFETs can be fabricated without thermal annealing. The process involves incorporation of an incompatible hydrocarbon binder or wax into the channel semiconductor composition to drive rapid phase separation and instantaneous crystallization of polymer semiconductor at room temperature. The resulting composite channel semiconductor film manifests a nano/microporous surface morphology with a continuous semiconductor nanowire network. OFET mobility of up to about 5 cm² V^?1 s^?1 and on/off ratio ≥ 10⁶ are attained. These are hitherto benchmark performance characteristics for room‐temperature, solution‐processed polymer OFETs, which are functionally useful for many impactful applications.     

High‐Speed Organic Single‐Crystal Transistor Responding to Very High Frequency Band

Although high carrier mobility organic field‐effect transistors (OFETs) are required for high‐speed device applications, improving the carrier mobility alone does not lead to high‐speed operation. Because the cut‐off frequency is determined predominantly by the total resistance and parasitic capacitance of a transistor, it is necessary to miniaturize OFETs while reducing these factors. Depositing a dopant layer only at the metal/semiconductor interface is an effective technique to reduce the contact resistance. However, fine‐patterning techniques for a dopant layer are still challenging especially for a top‐contact solution‐processed OFET geometry because organic semiconductors are vulnerable to chemical damage by solvents. In this work, high‐resolution, damage‐free patterning of a dopant layer is developed to fabricate short‐channel OFETs with a dopant interlayer inserted at the contacts. The fabricated OFETs exhibit high mobility exceeding 10 cm² V^?1 s^?1 together with a reasonably low contact resistance, allowing for high frequency operation at 38 MHz. In addition, a diode‐connected OFET shows a rectifying capability of up to 78 MHz at an applied voltage of 5 V. This shows that an OFET can respond to the very high frequency band, which is beneficial for long‐distance wireless communication.     

High‐Performance,Low‐Operating‐Voltage Organic Field‐Effect Transistors with Low Pinch‐Off Voltages

Organic field‐effect transistors suffer from ultra‐high operating voltages in addition to their relative low mobility. A general approach to low‐operating‐voltage organic field‐effect transistors (OFETs) using donor/acceptor buffer layers is demonstrated. P‐type OFETs with acceptor molecule buffer layers show reduced operating voltages (from 60–100 V to 10–20 V), with mobility up to 0.19 cm² V^?1 s^?1 and an on/off ratio of 3 × 10⁶. The subthreshold slopes of the devices are greatly reduced from 5–12 V/decade to 1.68–3 V/decade. This favorable combination of properties means that such OFETs can be operated successfully at voltages below 20 V (|V_DS| ≤ 20 V, |V_GS| ≤ 20 V). This method also works for n‐type semiconductors. The reduced operating voltage and low pinch‐off voltage contribute to the improved ordering of the polycrystalline films, reduced grain boundary resistance, and steeper subthreshold slopes.     

Ambient‐Stable,Annealing‐Free,and Ambipolar Organic Field‐Effect Transistors Based on Solution‐Processable Poly(2,2′‐bis(trifluoromethyl)biphenyl‐alt‐2,5‐divinylthiophene) without Long Alkyl Side Chains

An ambipolar conjugated polymer CF₃‐PBTV, poly(2,2′‐bis(trifluoromethyl)biphenyl‐alt‐2,5‐divinylthiophene), consisting of thienylenevinylene as the donor and trifluoromethyl‐substituted biphenyl as the acceptor has been successfully synthesized. CF₃‐PBTV shows solution‐processability without electrically insulating long alkyl side chains. Grazing incidence X‐ray diffraction results suggest a nearly equal population of flat‐on and end‐on domains in CF₃‐PBTV thin film. The excellent ambipolarity of CF₃‐PBTV is demonstrated by well‐equivalent charge mobilities of 0.065 and 0.078 cm² V^?1 s^?1 for p‐ and n‐channel, respectively. The organic field‐effect transistors (OFET) also shows very high on/off ratio (≈10⁷) which is attributed to the relatively large bandgap and low‐lying highest occupied molecular orbital (HOMO) of CF₃‐PBTV. The OFET performance barely changes after the device is stored in ambient conditions for 90 days. The ambient‐stability is attributed to the enhanced oxidative stability from its low‐lying HOMO and the better moisture resistance from its fluorine contents. The performance of CF₃‐PBTV based OFET is annealing independent. It is noteworthy that the solution‐processable, ambipolar, and thienylenevinylene‐containing conjugated polymer without any long alkyl side chains is reported for the first time. And to the best of our knowledge, it is the first ambient‐stable, annealing‐free OFET with well‐equivalent ambipolarity.     

High‐Mobility Air‐Stable Naphthalene Diimide‐Based Copolymer Containing Extended π‐Conjugation for n‐Channel Organic Field Effect Transistors

A high‐performance naphthalene diimide (NDI)‐based conjugated polymer for use as the active layer of n‐channel organic field‐effect transistors (OFETs) is reported. The solution‐processable n‐channel polymer is systematically designed and synthesized with an alternating structure of long alkyl substituted‐NDI and thienylene–vinylene–thienylene units (PNDI‐TVT). The material has a well‐controlled molecular structure with an extended π‐conjugated backbone, with no increase in the LUMO level, achieving a high mobility and highly ambient stable n‐type OFET. The top‐gate, bottom‐contact device shows remarkably high electron charge‐carrier mobility of up to 1.8 cm² V^?1 s^?1 (I_on/I_off = 10⁶) with the commonly used polymer dielectric, poly(methyl methacrylate) (PMMA). Moreover, PNDI‐TVT OFETs exhibit excellent air and operation stability. Such high device performance is attributed to improved π–π intermolecular interactions owing to the extended π‐conjugation, apart from the improved crystallinity and highly interdigitated lamellar structure caused by the extended π–π backbone and long alkyl groups.     

Fully Integrated Microscale Quasi‐2D Crystalline Molecular Field‐Effect Transistors

Monolithic integration of microscale organic field‐effect transistors (micro‐OFETs) is the only and inevitable path toward low‐cost large‐area electronics and displays. However, to date, such an ultimate technology has not yet evolved due to challenges in positioning and patterning highly crystalline microscale molecular layers as well as in developing micrometer scale integration schemes. In this work, by mastering the local growth of molecular semiconductors on pre‐defined terraces, single‐crystal quasi‐2D molecular layers tens of square micrometers in size are created in dense periodic arrays on a Si substrate. Nondestructive photolithographic processes are developed to pattern micro‐OFETs with mobilities up to 34.6 cm² V^?1 s^?1. This work demonstrates the feasibility to integrate arrays of short‐channel micro‐OFETs into electronic circuitry by highly parallel and size scalable fabrication technologies.     

Understanding the Meniscus‐Guided Coating Parameters in Organic Field‐Effect‐Transistor Fabrications

Meniscus‐guided coating (MGC) is mainly applicable on the soluble organic semiconductors with strong π–π overlap for achieving single‐crystalline organic thin films and high‐performance organic field‐effect‐transistors (OFETs). In this work, four elementary factors including shearing speed (v), solute concentration (c), deposition temperature (T), and solvent boiling point (T_b) are unified to analyze crystal growth behavior in the meniscus‐guided coating. By carefully varying and studying these four key factors, it is confirmed that v is the thickness regulation factor, while c is proportional to crystal growth rate. The MGC crystal growth rate is also correlated to latent heat (L) of solvents and deposition temperature in an Arrhenius form. The latent heat of solvents is proportional to T_b. The OFET channels grown by the optimized MGC parameters show uniform crystal morphology (Roughness R_q < 0.25 nm) with decent carrier mobilities (average µ = 5.88 cm² V^?1 s^?1 and highest µ = 7.68 cm² V^?1 s^?1). The studies provide a generalized formula to estimate the effects of these fabrication parameters, which can serve as crystal growth guidelines for the MGC approach. It is also an important cornerstone towards scaling up the OFETs for the sophisticated organic circuits or mass production.     

Polymer‐Based Organic Field‐Effect Transistors with Active Layers Aligned by Highly Hydrophobic Nanogrooved Surfaces

In this study, polymer‐based organic field‐effect transistors (OFETs) that exhibit alignment‐induced mobility enhancement, very small device‐to‐device variation, and high operational stability are successfully fabricated by a simple coating method of semiconductor solutions on highly hydrophobic nanogrooved surfaces. The highly hydrophobic nanogrooved surfaces (water contact angle >110°) are effective at inducing unidirectional alignment of polymer backbone structures with edge‐on orientation and are advantageous for realizing high operational stability because of their water‐repellent nature. The dewetting of the semiconductor solution is a critical problem in the thin film formation on highly hydrophobic surfaces. Dewetting during spin coating is suppressed by surrounding the hydrophobic regions with hydrophilic ones under appropriate designs. For the OFET array with an aligned terrace‐phase active layer of poly(2,5‐bis(3‐hexadecylthiophene‐2‐yl)thieno[3,2‐b]thiophene), the hole mobility in the saturation regime of 30 OFETs with channel current direction parallel to the nanogrooves is 0.513 ± 0.018 cm² V^?1 s^?1, which is approximately double that of the OFETs without nanogrooves, and the intrinsic operational stability is comparable to the operational stability of amorphous‐silicon field‐effect transistors. In other words, alignment‐induced mobility enhancement and high operational stability are successfully achieved with very small device‐to‐device variation. This coating method should be a promising means of fabricating high‐performance OFETs.     

Tuning Interfacial Properties by Spontaneously Generated Organic Interlayers in Top‐Contact‐Structured Organic Transistors

Controlling the interfacial properties between the electrode and active layer in organic field‐effect transistors (OFETs) can significantly affect their contact properties, resulting in improvements in device performance. However, it is difficult to apply to top‐contact‐structured OFETs (one of the most useful device structures) because of serious damage to the organic active layer by exposing solvent. Here, a spontaneously controlled approach is explored for optimizing the interface between the top‐contacted source/drain electrode and the polymer active layer to improve the contact resistance (R_C). To achieve this goal, a small amount of interface‐functionalizing species is blended with the p‐type polymer semiconductor and functionalized at the interface region at once through a thermal process. The R_C values dramatically decrease after introduction of the interfacial functionalization to 15.9 kΩ cm, compared to the 113.4 kΩ cm for the pristine case. In addition, the average field‐effect mobilities of the OFET devices increase more than three times, to a maximum value of 0.25 cm² V^?1 s^?1 compared to the pristine case (0.041 cm² V^?1 s^?1), and the threshold voltages also converge to zero. This study overcomes all the shortcomings observed in the existing results related to controlling the interface of top‐contact OFETs by solving the discomfort of the interface optimization process.     

Reusable Cellulose‐Based Hydrogel Sticker Film Applied as Gate Dielectric in Paper Electrolyte‐Gated Transistors

A new concept for reusable eco‐friendly hydrogel electrolytes based on cellulose is introduced. The reported electrolytes are designed and engineered through a simple, fast, low‐cost, and eco‐friendly dissolution method of microcrystalline cellulose at low temperature using an aqueous LiOH/urea solvent system. The cellulose solution is combined with carboxymethyl cellulose, followed by the regeneration and simultaneous ion incorporation. The produced free standing cellulose‐based electrolyte films exhibit interesting properties for application in flexible electrochemical devices, such as biosensors or electrolyte‐gated transistors (EGTs), because of their high specific capacitances (4–5 µF cm^?2), transparency, and flexibility. Indium–gallium–zinc‐oxide EGTs on glass with laminated cellulose‐based hydrogel electrolytes (CHEs) as the gate dielectric are produced presenting a low working voltage (<2 V), showing an on–off current ratio (I _on/off) of 10⁶, a subthreshold swing lower than 0.2 V dec^?1, and saturation mobility (μ_Sat) reaching 26 cm² V^?1 s^?1. The flexible CHE‐gated transistors on paper are also demonstrated, which operate at switching frequencies up to 100 Hz. Combining the flexibility of the EGTs on paper with the reusability of the developed CHEs is a breakthrough toward biodegradable advanced functional materials allied with disposable/recyclable and low‐cost electronic devices.     

Layer‐by‐Layer Conjugated Extension of a Semiconducting Polymer for High‐Performance Organic Field‐Effect Transistor

A donor–acceptor (D–A) semiconducting copolymer, PDPP‐TVT‐29, comprising a diketopyrrolopyrrole (DPP) derivative with long, linear, space‐separated alkyl side‐chains and thiophene vinylene thiophene (TVT) for organic field‐effect transistors (OFETs) can form highly π‐conjugated structures with an edge‐on molecular orientation in an as‐spun film. In particular, the layer‐like conjugated film morphologies can be developed via short‐term thermal annealing above 150 °C for 10 min. The strong intermolecular interaction, originating from the fused DPP and D–A interaction, leads to the spontaneous self‐assembly of polymer chains within close proximity (with π‐overlap distance of 3.55 Å) and forms unexpectedly long‐range π‐conjugation, which is favorable for both intra‐ and intermolecular charge transport. Unlike intergranular nanorods in the as‐spun film, well‐conjugated layers in the 200 °C‐annealed film can yield more efficient charge‐transport pathways. The granular morphology of the as‐spun PDPP‐TVT‐29 film produces a field‐effect mobility (μ _FET) of 1.39 cm² V^?1 s^?1 in an OFET based on a polymer‐treated SiO₂ dielectric, while the 27‐Å‐step layered morphology in the 200 °C‐annealed films shows high μ _FET values of up to 3.7 cm² V^?1 s^?1.     

Stable Delocalized Singlet Biradical Hydrocarbon for Organic Field‐Effect Transistors

Delocalized singlet biradical hydrocarbons hold promise as new semiconducting materials for high‐performance organic devices. However, to date biradical organic molecules have attracted little attention as a material for organic electronic devices. Here, this work shows that films of a crystallized diphenyl derivative of s‐indacenodiphenalene (Ph₂‐IDPL) exhibit high ambipolar mobilities in organic field‐effect transistors (OFETs). Furthermore, OFETs fabricated using Ph₂‐IDPL single crystals show high hole mobility (μ_h = 7.2 × 10^?1 cm² V^?1 s^?1) comparable to that of amorphous Si. Additionally, high on/off ratios are achieved for Ph₂‐IDPL by inserting self‐assembled mono­layer of alkanethiol between the semiconducting layer and the Au electrodes. These findings open a door to the application of ambipolar OFETs to organic electronics such as complementary metal oxide semiconductor logic circuits.     

High Tg Cyclic Olefin Copolymer Gate Dielectrics for N,N′‐Ditridecyl Perylene Diimide Based Field‐Effect Transistors: Improving Performance and Stability with Thermal Treatment

A novel application of ethylene‐norbornene cyclic olefin copolymers (COC) as gate dielectric layers in organic field‐effect transistors (OFETs) that require thermal annealing as a strategy for improving the OFET performance and stability is reported. The thermally‐treated N,N′‐ditridecyl perylene diimide (PTCDI‐C13)‐based n‐type FETs using a COC/SiO₂ gate dielectric show remarkably enhanced atmospheric performance and stability. The COC gate dielectric layer displays a hydrophobic surface (water contact angle = 95° ± 1°) and high thermal stability (glass transition temperature = 181 °C) without producing crosslinking. After thermal annealing, the crystallinity improves and the grain size of PTCDI‐C13 domains grown on the COC/SiO₂ gate dielectric increases significantly. The resulting n‐type FETs exhibit high atmospheric field‐effect mobilities, up to 0.90 cm² V^?1 s^?1 in the 20 V saturation regime and long‐term stability with respect to H₂O/O₂ degradation, hysteresis, or sweep‐stress over 110 days. By integrating the n‐type FETs with p‐type pentacene‐based FETs in a single device, high performance organic complementary inverters that exhibit high gain (exceeding 45 in ambient air) are realized.     

A High‐k Fluorinated P(VDF‐TrFE)‐g‐PMMA Gate Dielectric for High‐Performance Flexible Field‐Effect Transistors

A newly synthesized high‐k polymeric insulator for use as gate dielectric layer for organic field‐effect transistors (OFETs) obtained by grafting poly(methyl methacrylate) (PMMA) in poly(vinylidene fluoride‐trifluoroethylene) (P(VDF‐TrFE)) via atom transfer radical polymerization transfer is reported. This material design concept intents to tune the electrical properties of the gate insulating layer (capacitance, leakage current, breakdown voltage, and operational stability) of the high‐k fluorinated polymer dielectric without a large increase in operating voltage by incorporating an amorphous PMMA as an insulator. By controlling the grafted PMMA percentage, an optimized P(VDF‐TrFE)‐g‐PMMA with 7 mol% grafted PMMA showing reasonably high capacitance (23–30 nF cm^?2) with low voltage operation and negligible current hysteresis is achieved. High‐performance low‐voltage‐operated top‐gate/bottom‐contact OFETs with widely used high mobility polymer semiconductors, poly[[2,5‐bis(2‐octyldodecyl)‐2,3,5,6‐tetrahydro‐3,6‐dioxopyrrolo [3,4‐c]pyrrole‐1,4‐diyl]‐alt‐[[2,2′‐(2,5‐thiophene)bis‐thieno(3,2‐b)thiophene]‐5,5′‐diyl]] (DPPT‐TT), and poly([N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)) are demonstrated here. DPPT‐TT OFETs with P(VDF‐TrFE)‐g‐PMMA gate dielectrics exhibit a reasonably high field‐effect mobility of over 1 cm² V^?1 s^?1 with excellent operational stability.     

Boosting the Charge Transport Property of Indeno[1,2‐b]fluorene‐6,12‐dione though Incorporation of Sulfur‐ or Nitrogen‐Linked Side Chains

Alkyl chains are basic units in the design of organic semiconductors for purposes of enhancing solubility, tuning electronic energy levels, and tailoring molecular packing. This work demonstrates that the carrier mobilities of indeno[1,2‐b ]fluorene‐6,12‐dione ( IFD )‐based semiconductors can be dramatically enhanced by the incorporation of sulfur‐ or nitrogen‐linked side chains. Three IFD derivatives possessing butyl, butylthio, and dibutylamino substituents are synthesized, and their organic field‐effect transistors (OFET) are fabricated and characterized. The IFD possessing butyl substituents exhibits a very poor charge transport property with mobility lower than 10^?7 cm² V^?1 s^?1. In contrast, the hole mobility is dramatically increased to 1.03 cm² V^?1 s^?1 by replacing the butyl units with dibutylamino groups ( DBA‐IFD ), while the butylthio‐modified IFD ( BT‐IFD ) derivative exhibits a high and balanced ambipolar charge transport property with the maximum hole and electron mobilities up to 0.71 and 0.65 cm² V^?1 s^?1, respectively. Moreover, the complementary metal–oxide–semiconductor‐like inverters incorporated with the ambipolar OFETs shows sharp inversions with a maximum gain value up to 173. This work reveals that modification of the aromatic core with heteroatom‐linked side chains, such as alkylthio or dialkylamino, can be an efficient strategy for the design of high‐performance organic semiconductors.     

High‐Mobility n‐Type Organic Transistors Based on a Crystallized Diketopyrrolopyrrole Derivative

A new high‐performing small molecule n‐channel semiconductor based on diketopyrrolopyrrole (DPP), 2,2′‐(5,5′‐(2,5‐bis(2‐ethylhexyl)‐3,6‐dioxo‐2,3,5,6‐tetrahydropyrrolo[3,4‐c]pyrrole‐1,4‐diyl)bis(thiophene‐5,2‐diyl))bis(methan‐1‐yl‐1‐ylidene)dimalononitrile (DPP‐T‐DCV), is successfully synthesized. The frontier molecular orbitals in this designed structure are elaborately tuned by introducing a strong electron‐accepting functionality (dicyanovinyl). The well‐defined lamellar structures of the crystals display a uniform terrace step height corresponding to a molecular monolayer in the solid‐state. As a result of this tuning and the remarkable crystallinity derived from the conformational planarity, organic field‐effect transistors (OFETs) based on dense‐packed solution‐processed single‐crystals of DPP‐T‐DCV exhibit an electron mobility (μ_e) up to 0.96 cm² V^?1 s^?1, one of the highest values yet obtained for DPP derivative‐based n‐channel OFETs. Polycrystalline OFETs show promise (with an μ_e up to 0.64 cm² V^?1 s^?1) for practical utility in organic device applications.     

Effects of P3HT concentration on the performance of organic field effect transistors

Top-contact organic field effect transistors(OFETs) based on poly(3-hexylthiophene)(P3HT) with different concentrations in chloroform(CHCl3) are fabricated.The output characteristics indicate that the P3HT concentration has significant influence on the OFET devices.The performance of the devices firstly is enhanced with increasing the P3HT concentration,and then decreases.The optimized devices with the P3HT concentration of 2 mg/mL show the best performance.The fieldeffect mobility is up to 1.4×10-2 cm2/Vs,...     

Organic Electronics: High Tg Cyclic Olefin Copolymer Gate Dielectrics for N,N′‐Ditridecyl Perylene Diimide Based Field‐Effect Transistors: Improving Performance and Stability with Thermal Treatment (Adv. Funct. Mater. 16/2010)

A novel application of ethylene‐norbornene cyclic olefin copolymers (COC) as gate dielectric layers in organic field‐effect transistors (OFETs) that require thermal annealing as a strategy for improving the OFET performance and stability is reported. The thermally‐treated N,N′‐ditridecyl perylene diimide (PTCDI‐C13)‐based n‐type FETs using a COC/SiO₂ gate dielectric show remarkably enhanced atmospheric performance and stability. The COC gate dielectric layer displays a hydrophobic surface (water contact angle = 95° ± 1°) and high thermal stability (glass transition temperature = 181 °C) without producing crosslinking. After thermal annealing, the crystallinity improves and the grain size of PTCDI‐C13 domains grown on the COC/SiO₂ gate dielectric increases significantly. The resulting n‐type FETs exhibit high atmospheric field‐effect mobilities, up to 0.90 cm² V^?1 s^?1 in the 20 V saturation regime and long‐term stability with respect to H₂O/O₂ degradation, hysteresis, or sweep‐stress over 110 days. By integrating the n‐type FETs with p‐type pentacene‐based FETs in a single device, high performance organic complementary inverters that exhibit high gain (exceeding 45 in ambient air) are realized.     

Synergistic Use of Pyridine and Selenophene in a Diketopyrrolopyrrole‐Based Conjugated Polymer Enhances the Electron Mobility in Organic Transistors

To achieve semiconducting materials with high electron mobility in organic field‐effect transistors (OFETs), low‐lying energy levels (the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO)) and favorable molecular packing and ordering are two crucial factors. Here, it is reported that the incorporation of pyridine and selenophene into the backbone of a diketopyrrolopyrrole (DPP)‐based copolymer produces a high‐electron‐mobility semiconductor, PDPPy‐Se. Compared with analogous polymers based on other DPP derivatives and selenophene, PDPPy‐Se features a lower LUMO that can decrease the electron transfer barrier for more effective electron injection, and simultaneously a lower HOMO that, however, can increase the hole transfer barrier to suppress the hole injection. Combined with thermal annealing at 240 °C for thin film morphology optimization to achieve large‐scale crystallite domains with tight molecular packing for effective charge transport along the conducting channel, OFET devices fabricated with PDPPy‐Se exhibit an n‐type‐dominant performance with an electron mobility (μ_e) as high as 2.22 cm² V^?1 s^?1 and a hole/electron mobility ratio (μ_h/μ_e) of 0.26. Overall, this study demonstrates a simple yet effective approach to boost the electron mobility in organic transistors by synergistic use of pyridine and selenophene in the backbone of a DPP‐based copolymer.