Effect of interface state trap density on the characteristics of n-type,enhancement-mode,implant-free In0.3Ga0.7As MOSFETs

The effect of interface state trap density, D_it, on the device characteristics of n-type, enhancement-mode, implant-free (IF) In_0.3Ga_0.7As MOSFETs [1], [2] has been investigated using a commercial drift-diffusion (DD) device simulation tool. Methodology has been developed to include arbitrary D_it distributions in the input simulation decks to more accurately fit the measured subthreshold characteristics of recently reported 1.0 μm gate length IF In_0.3Ga_0.7As MOSFETs [3]. The impact of interface states on a scaled 30 nm gate length IF MOSFET is also reported.     

Analysis of nanometer-scale InGaAs/InAs/InGaAs composite channel MOSFETs using high-K dielectrics for high speed applications

The outstanding electron transport properties of InGaAs and InAs semiconductor materials, makes them attractive candidates for future nano-scale CMOS. In this paper, the ON state and OFF state performance of 30 nm gate length InGaAs/InAs/InGaAs buried composite channel MOSFETs using various high-K dielectric materials is analyzed using Synopsys TCAD tool. The device features a composite channel to enhance the mobility, an InP spacer layer to minimize the defect density and a heavily doped multilayer cap. The simulation results show that MOSFETs with Al₂O₃/ZrO₂ bilayer gate oxide exhibits higher gm/I_D ratio and lower sub threshold swing than with the other dielectric materials. The measured values of threshold voltage (V_T), on resistance (R_ON) and DIBL for Lg = 30 nm In_0.53Ga_0.47As/InAs/In_0.53Ga_0.47As composite channel MOSFET having Al₂O₃/ZrO₂ (EOT = 1.2 nm) bilayer dielectric as gate oxide are 0.17 V, 290 Ω-µm, and 65 mV/V respectively. The device displays a transconductance of 2 mS/µm.     

Challenges and performance limitations of high-k and oxynitride gate dielectrics for 90/65 nm CMOS technology

For low power applications, the increase of gate leakage current, caused by direct tunneling in ultra-thin oxide films, is the crucial factor eliminating conventional SiO₂-based gate dielectrics in sub-90 nm CMOS technology development. Recently, promising performance has been demonstrated for poly-Si/high-k and poly-Si/SiON gate stacks in addressing gate leakage requirements for low power applications. However, the use of poly-Si gate electrodes on high-k created additional issues such as channel mobility and reliability degradations, as well as Fermi level pinning of the effective gate work function. Therefore, oxynitride gate dielectrics are being proposed as an intermediate solution toward the sub-65/45 nm nodes. Apparently, an enhanced SiON gate dielectric stack was developed and reported to achieve high dielectric constant and good interfacial properties. The purpose of this paper is to provide a comprehensive review some of the device performance and limitation that high-k and oxynitride as dielectric materials are facing for sub-65/45 nm node.     

A methodology for projecting SiO2 thick gate oxide reliability on trench power MOSFETs and its application on MOSFETs VGS rating

In this work, a methodology based on the E-model for the reliability projection of a thick (> 20 nm) SiO₂ gate oxide on a vertical trench power MOSFET, is presented. Experimental results suggest that a Logic Level (LL) trench MOSFET with 35 nm of gate oxide can be rated at V_GS = + 12 V if one assumes continuous DC Gate-Source bias of V_GS = + 12 V at T = 175 °C for 10 years at a defect level of 1 Part Per Million (PPM). We will demonstrate that if we take into account MOSFET device lifetime as dictated by the Automotive Electronics Council (AEC Q101) mission profile, then devices can be rated higher to V_GS = + 14.7 V at T = 175 °C for the same PPM level (1 PPM). The application of the methodology for establishing the oxide thickness, t_ox, for any required voltage rating, is discussed.     

Microwave performance of field-plate 0.13-μm MOS transistors with varying field-plate extension

Si-based field-plate 0.13 μm gate length metal-oxide-semiconductor field effect transistor (Si MOSFET) with field-plate (FP) lengths of 0.1 μm, 0.2 μm, and 0.3 μm have been fabricated and investigated. The field-plate metals were connected to gate electrode in this study to improve device gate resistance (R_g) resulting in the better microwave performance. By increasing the length of field-plate metal extension (L_FPE), the off-state drain-to-source surface leakage current can be suppressed. Besides, low surface traps in FP NMOS also leads to a higher drain-to-source current (I_ds) especially at high current regime compared to standard device. The power added efficiency (PAE) was 56.3% for L_FPE of 0.3 μm device, and these values where 54.7% and 53.8% for L_FPE of 0.2 μm and 0.1 μm devices, respectively. Wider field-plate metal extension exhibits highly potential for low noise amplifier and high efficiency power amplifier applications.     

Impact of gate material engineering(GME) on analog/RF performance of nanowire Schottky-barrier gate all around (GAA) MOSFET for low power wireless applications: 3D T-CAD simulation

In this paper Gate Material Engineered (GME) Gate-Stack (GS) silicon nanowire Schottky-Barrier (SB) Gate All Around (GAA) MOSFET and Single Material Gate Stack Schottky-Barrier Source/Drain Gate All Around (SM-GS-SB-S/D GAA) structures are proposed for low- power wireless applications. The Analog/RF performance for wireless applications of these devices are demonstrated. The effect of Schottky-Barrier (Metal) S/D is studied for Single Metal (SM)–SB-GAA, (Dual Metal) DM-SB-GAA, SM-GS-SB-GAA and GME-GS-SB-GAA MOSFETs, and it is found that GME-GS-SB-GAA MOSFET with metal drain source shows much improved performance in terms of transconductance (g_m), output conductance (g_d), Early Voltage (V_EA), Maximum Transducer Power Gain, cut-off frequency (f_T), and I_on/I_off ratio. Further, harmonic distortion for wireless applications is also studied using ATLAS-3D device simulator. Due to low parasitic S/D resistance the metal Source/Drain DM-GS-SB-S/D-GAA MOSFET demonstrates remarkable I_on of~31.8 μA/μm and saturation transconductance g_m of~68.2 μS with improved third order derivative of transconductance g_m3.     

Simulation study of Insulated Shallow Extension Silicon On Nothing (ISESON) MOSFET for high temperature applications

This paper analyzes the effect of temperature variation on various device architectures i.e. Insulated Shallow Extension Silicon On Nothing (ISESON), ISE and SON MOSFET using ATLAS 3D device simulator for 45 nm gate length. The simulation results obtained with the ATLAS has been validated by comparing it with reported experimental data of SON MOSFET. The simulation results demonstrate that out of three device designs, the ISESON MOSFET is the most suitable device for high speed, low voltage and high temperature applications. The integration of ISE and SON onto the conventional bulk MOSFET leads to the enhancement in analog device performance in terms of device efficiency (g_m/I_ds), device gain (g_m/g_d), output resistance (R_out) and early voltage (V_ea).     

Scaling the MOSFET gate dielectric: From high-k to higher-k? (Invited Paper)

We discuss options for metal–oxide-semiconductor field-effect transistor (MOSFET) gate stack scaling with thin titanium nitride metal gate electrodes and high-permittivity (‘high-k’) gate dielectrics, aimed at gate-first integration schemes. Both options are based on further increasing permittivity of the dielectric stack. First, we show that hafnium-based stacks such as TiN/HfO₂ can be scaled to capacitance equivalent thickness in inversion (T_inv) of 10 Å and equivalent oxide thickness (EOT) of 6 Å by using silicon nitride instead of silicon oxide as a high-k/channel interfacial layer. This is based on the higher dielectric constant of Si₃N₄ and on its resistance to oxidation. Although the nitrogen introduces positive fixed charges, carrier mobility is not degraded. Secondly, we investigate whether Ti-based ‘higher-k’ dielectrics have the potential to ultimately replace Hf. We discuss oxygen loss from TiO₂ as a main challenge, and identify two migration pathways for such oxygen atoms: In addition to well-known down-diffusion and channel Si oxidation, we have newly observed oxygen up-diffusion through the TiN metal gate, forming SiO₂ at the poly-Si contact. We further address the performance of Si₃N₄ and HfO₂ as oxygen barrier layers.     

Degradation of pMOSFETs due to hot electron induced punchthrough

This paper proposes a method which can separate the parasitic effect from the drain current I_d vs. gate voltage V_g curves of MOSFETs, then uses this method to analyze degradation of experimental pMOSFETs due to hot-electron-induced punchthrough (HEIP). An I_d vs. V_g curve of the parasitic MOSFET formed by a shallow trench isolation (STI) is obtained by extrapolating the line of I_d vs. channel width W at each V_g to W = 0 μm. The I_d vs. V_g curves of the parasitic MOSFET indicate that HEIP caused electron trapping at the interface between SiN and the sidewall oxide of STI, but the curves of the main MOSFET indicate that HEIP caused negative oxide charges and positive interface traps in the channel region. These charges and traps decreased the threshold voltage V_th of the parasitic MOSFET but increased V_th of the main MOSFET. These two opposite behaviors of V_th resulted in little HEIP-induced shift of V_th at W = 2.5 μm. | V_d | to secure ten-year HEIP lifetime of 10% shift of V_th was ≤ 2.2 V at W = 0.3 μm, ≤ 3.5 V at W = 1.0 μm, and ≤ 3.6 V at W = 10 μm; these changes indicate that degradation of parasitic MOSFET influences the HEIP lifetime of narrow pMOSFET significantly.     

Drivability improvement in Schottky barrier source/drain MOSFETs with strained-Si channel by Schottky barrier height reduction

Due to an extra barrier between source and channel, the drivability of Schottky barrier source/drain MOSFETs (SBMOSFETs) is smaller than that of conventional transistors. To reach the drivability comparable to the conventional MOSFET, the Schottky barrier height (SBH) should be lower than a critical value. It is expected that SBH can be effectively reduced by a bi-axially strain on Si. In this letter, p-channel MOSFETs with PtSi Schottky barrier source/drain, HfAlO gate dielectric, HfN/TaN metal gate and strained-Si channel are demonstrated for the first time using a simplified low temperature process. Devices with the channel length of 4 μm have the drain current of 9.5 μA/μm and the transconductance of 14 μS/μm at V_gs − V_th = V_ds = −1 V. Compared to the cubic Si counterpart, the drain current and the transconductance are improved up to 2.7 and 3.1 times respectively. The improvement is believed to arising from the reduced barrier height of the PtSi/strained-Si contact and the enhanced hole mobility in the strained-Si channel.     

Underlap channel metal source/drain SOI MOSFET for thermally efficient low-power mixed-signal circuits

In this paper it has been shown that employing an underlap channel created by varying the lateral doping straggle in dopant-segregated Schottky barrier SOI MOSFET not only improves the scalability but also suppresses the self-heating effect of this device. Although in strong inversion region the reduced effective gate voltage due to voltage drop across the underlap lengths reduces the drive current, in weak/moderate inversion region defined at I_D=5 μA/μm and V_DS=0.5 V the analog figures of merit such as transconductance, transconductance generation factor and intrinsic gain of the proposed underlap device are improved by 15%, 35% and 20%, respectively over the conventional overlap channel structure. In addition to this, at V_DD=0.5 V the gain-bandwidth product in a common-source amplifier based on proposed underlap device is improved by ～20% over an amplifier based on the conventional overlap channel device. The mixed-mode device/circuit simulation results of CMOS inverter, NAND and the NOR gates based on these devices also show that at V_DD=0.5 V the switching energy, static power dissipation and the propagation delay in the case of proposed underlap device are reduced by ～10%, ～35% and ～25%, respectively, over the conventional overlap device. Thus, significant improvement in analog figures of merit and the reduction in digital design metrics at lower supply voltage show the suitability of the proposed underlap device for low-power mixed-signal circuits.     

Analysis of the electrical characteristics of power LDMOSFETs having different design parameters under various temperature

In this paper, we have investigated the electrical characteristics of power lateral double-diffused MOSFETs (LDMOSFETs) having different gate lengths (2.1–3 μm) and drift lengths (6.6–12.6 μm) in the temperature range 100–500 K. The results of this study indicate that gate length and drift region length have a great effect on electrical characteristics, but they have little effect on temperature dependence. The specific on-resistance and the off-state breakdown voltage increase with temperature. The result shows that the specific on-resistance increases exponentially with the exponent 2.2 and, by contrast, the off-state breakdown voltage increases linearly with a slope of 100 mV/K (drift region concentration of measured device: 2×10¹⁵ cm⁻³). As a result, R_on/BV, known for a figure of merit of power device, increases with temperature.     

UV nanoimprint lithography process optimization for electron device manufacturing on nanosized scale

Imprint specific process parameters like the residual layer thickness and the etch resistance of the UV polymers for the substrate etch process have to be optimized to introduce UV nanoimprint lithography (UV NIL) as a high-resolution, low-cost patterning technique for research and industry into electron device manufacturing. Additionally, UV NIL processes have to be compatible with conventional silicon (Si) semiconductor processing. Within this work, the minimization of the residual layer thickness by using a multi-drop ink-jet system, which was integrated into the imprint stepper NPS300 from S-E-T-(formerly SUSS MicroTec), in combination with a low viscous UV polymer from Asahi Glass Company is shown. The etch resistance of different UV polymers against the poly-Si etch process was increased by 50% with an appropriate post-exposure bake. A poly-Si dry etch process was used to pattern the gates of short channel MOSFETs. After optimizing the poly-Si etch, properly working short channel MOSFETs with a minimum gate length of about 90 nm were fabricated demonstrating successfully the compatibility of UV NIL with conventional Si semiconductor processing on nanosized scale.     

Effect of gate length in InAs/AlSb HEMTs biased for low power or high gain

The effect of gate-length variation on DC and RF performance of InAs/AlSb HEMTs, biased for low DC power consumption or high gain, is reported. Simultaneously fabricated devices, with gate lengths between 225 nm and 335 nm, have been compared. DC measurements revealed higher output conductance g_ds and slightly increased impact ionization with reduced gate length. When reducing the gate length from 335 nm to 225 nm, the DC power consumption was reduced by approximately 80% at an f_T of 120 GHz. Furthermore, a 225 nm gate-length HEMT biased for high gain exhibited an extrinsic f_T of 165 GHz and an extrinsic f_max of 115 GHz, at a DC power consumption of 100 mW/mm. When biased for low DC power consumption of 20 mW/mm the same HEMT exhibited an extrinsic f_T and f_max of 120 GHz and 110 GHz, respectively.     

Electrical properties of Π-conjugated Fe-TPP molecular solar cell device

A heterojunction device of Au/Fe-TPP/n-Si/Al was assembled by thermally evaporated deposition. The dark current density–voltage characteristics of device were investigated. Results showed a rectification behavior. Measurements of thermo electric power confirm that Fe-TPP thin film behaves as p-type semiconductors. Electronic parameters such as barrier height, diode ideality factor, series resistance, shunt resistance were found to be 0.83 eV, 1.5, 7 × 10⁵ Ω and 2 × 10¹⁰ Ω, respectively. The Au/Fe-TPP/n-Si/Al device indicates a photovoltaic behavior with an open circuit voltage V_oc of 0.52 V, short circuit current I_sc of 2.22 × 10^?6 A, fill factor FF of 0.49 and conversion efficiency 1.13% under white light illumination power 50 W/m².     

Strain sensitivity of gate leakage in strained-SOI nMOSFETs: A benefit for the performance trade-off and a novel way to extract the strain-induced band offset

The impact of biaxial stress on gate leakage is investigated on fully-depleted silicon-on-insulator (FD-SOI) nMOS transistors, integrating either a standard gate stack or an advanced high-κ/metal gate stack. It is demonstrated that strained devices exhibit significantly reduced leakage currents (up to ?90% at E_ox = 11 MV/cm for σ_tensile = 2.5 GPa). This specific effect is used to extract the conduction band offset ΔEc induced by strain and is shown to be accurate enough to monitor stress in MOSFETs. This new technique is much less sensitive to gate oxide defects than the method based on the threshold voltage shift ΔV_T. This accurate experimental extraction allowed us to pick out realistic values for the deformation potentials in silicon (Ξ_u = 8.5 eV and Ξ_d = ?5.2 eV), among the published values.     

Punch-through impact ionization MOSFET (PIMOS): From device principle to applications

In the present work a punch-through impact ionization MOSFET (PIMOS) is presented, which exploits impact ionization in low-doped body-tied Ω- and tri-gate structures to obtain abrupt switching (3–10 mV/decade) combined with a hysteresis in the I_D(V_DS) and I_D(V_GS) characteristics. The PIMOS device shows an extraordinary temperature stability up to 125 °C. The influence of various parameters on device performance as abrupt switch or memory cell is investigated. Reduction of the electrical channel length, i.e. of gate length and/or substrate doping, reduces the breakdown voltage and hence the DRAM operating voltage, but also increase the I_off. Two architectures for a capacitor-less DRAM cell are demonstrated and evaluated. In addition, a PIMOS n-type hysteretic inverter is demonstrated, which may serve as a 1T SRAM cell.     

Effects of the post nitridation anneal temperature on performances of the nano MOSFET with ultra-thin (<2.5 nm) plasma nitrided gate dielectric

A post nitridation annealing (PNA) is used to improve performances of the metal oxide semiconductor field effect transistor (MOSFETs) with nano scale channel and pulsed radio frequency decoupled plasma nitrided ultra-thin (<50 Å) gate dielectric. Effects of the PNA temperature on the gate leakage and the device performances are investigated in details. For a n-type MOSFET, as the PNA temperature rises from 1000 to 1050 °C, the saturation current and gate leakage are increased and reduced 7.9% and 3.81%, respectively. For a p-type MOSFET, the improvement is more significant i.e., 16.7% and 4.31% in saturation current increase and gate leakage reduction, respectively. The significant improvements in performance are attributed to the higher PNA temperature caused Si/SiON interface improvement and increase of EOT. Most of all, the high temperature PNA does not degrade the gate oxide integrity.     

Charge trapping related channel modulation instability in P-GaN gate HEMTs

In this paper, a study of the channel modulation instability of commercial p-GaN gate HEMTs is presented. During the gate-voltage stress test, substantial R_DS(ON) variations up to 78 mΩ (93.8%) were observed. It is found that the p-GaN/AlGaN/GaN gate structure enables the injection of holes and electrons, which can be captured by the donor/acceptor-like traps located in the AlGaN layer. Therefore, the trapped holes and electrons concurrently modulate the channel conductivity, resulting in R_DS(ON) variations. Device simulation was performed to help explain the mechanism from the perspective of energy band. In addition, results reveal that with the recommended working gate-voltage stress V_GS = 7 V, the on-state resistance, the threshold voltage and the off-state drain to source leakage current vary up to 8 mΩ (16.3%), 0.2 V (14.8%) and 12.8 μA (42.66%) within 1 h, respectively, which could raise reliability issues for the power electronics applications of p-GaN gate HEMTs.     

The effect of gate overlap lightly doped drains on low temperature poly-Si thin film transistors

Low temperature polycrystalline silicon (LTPS) thin-film transistors (TFTs) have a high carrier mobility that enables the design of small devices that offer large currents and fast switching speeds. However, the electrical characteristics of the conventional self-aligned polycrystalline silicon (poly-Si) TFTs are known to present several undesired effects, such as large leakage currents, the kink effect, and the hot-carrier effect. For this paper, LTPS TFTs were fabricated, and the SiN_x/SiO₂ gate dielectrics and the effect of the gate-overlap lightly doped drain (GOLDD) were analyzed in order to minimize these undesired effects. GOLDD lengths of 1, 1.5 and 2 μm were used, while the thickness of the gate dielectrics (SiN_x/SiO₂) was fixed at 65 nm (40 nm/25 nm). The electrical characteristics show that the kink effect is reduced in the LTPS TFTs using a more than 1.5 μm of GOLDD length. The TFTs with the GOLDD structure have more stable characteristics than the TFTs without the GOLDD structure under bias stress. The degradation from the hot-carrier effect was also decreased by increasing the GOLDD length. After applying the hot-carrier stress test, the threshold voltage variation (ΔV_TH) was decreased from 0.2 V to 0.06 V by the increase of the GOLDD length. The results indicate that the TFTs with the GOLDD structure were protected from the degradation of the device due to the decreased drain field. From these results it can be seen that the TFTs with the GOLDD structure can be applied to achieve high stability and high performance in driving circuit applications for flat-panel displays.