Microwave Characteristics of A(B3+1/2B5+1/2)O3 Ceramics (A = Ba, Ca, Sr; B3+= La, Nd, Sm, Yb; B5+= Nb, Ta)

Dielectric properties of A(B³⁺_1/2B⁵⁺_1/2)O₃ (A = Ba, Ca, Sr; B³⁺= La, Nd, Sm, Yb; B⁵⁺= Nb, Ta) ceramics have been investigated at microwave frequencies. Sr(B³⁺_1/2B⁵⁺_1/2)O₃ and Ca(B³⁺_1/2B⁵⁺_1/2)O₃ ceramics have relative dielectric constants (ε _r ) above 20 and negative temperature coefficients of resonant frequency (T _f ). In the group of Ba(B³⁺_1/2B⁵⁺_1/2)O₃ ceramics, T _f changes from + 118 ppm/° to nearly zero according to the kinds of B-site ions. Among the ceramics investigated, Sr(Sm_1/2Ta_1/2)O₃ ceramics have the highest Q values at microwave frequencies. For Sr(Sm_1/2Ta_1/2)O₃ ceramics Q = 7000, ε _r = 27.7, and T _f =−62.5 ppm/° at 8.5 GHz. The microstructure of Sr(Sm_1/2Ta_1/2)O₃ ceramics is composed of a matrix of the ternary compound (Sr-Sm-Ta-O system) and secondary phase grains of the binary compound (Sm-Ta-O system).     

Structure Evolution from Pb(Mg1/3Nb2/3)O3 to La(Mg2/3Nb1/3)O3

The crystal structure of lanthanum-modified lead magnesium niobates having composition (Pb_{1− x} La _x ) (Mg_{(1+ x )/3}-Nb_{(2− x )/3})O₃ with X = 0 to 1 was investigated by X-ray powder diffraction. It was found that the fundamental reflections from perovskite structure remain in the whole range of composition. The superlattice reflections from the A(B'_1/2-B"_1/2)O₃ ordered structure are also well preserved for La content greater than 50 at.%; however, a series of extra peaks of mixing indices appears, with intensities gradually enhanced with the increase of La content. For the complete substitution of Pb by La, a splitting of some reflections can be observed in the diffraction pattern. The results indicate that the crystal structure evolves continuously with the La content, from disordered cubic perovskite of space group Pm 3 m for X = 0, to ordered cubic perovskite of space group Fm 3 m for X = 0.5, distorted cubic perovskite of space group Pa 3 for 0.5 < X < 0.9, and finally to a rhombohedral perovskite, possibly belonging to the space group R 3 , for X ≥ 0.9. In the evolution of structure, a linear reduction of the lattice constant of the perovskite cell from 4.048 to 3.964 Å was observed.     

Porous Glass-Ceramics with a Skeleton of the Fast-Lithium-Conducting Crystal Li1+xTi2−xAlx(PO4)3

Porous glass-ceramics with a skeleton of the fast-lithium-conducting crystal Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ (where x = 0.3–0.5) were prepared by crystallization of glasses in the Li₂O─CaO─TiO₂─Al₂O₃–P₂O₅ system and subsequent acid leaching of the resulting dense glass-ceramics composed of the interlocking of Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ and β-Ca₃(PO₄)₂ phases. The median pore diameter and surface area of the resulting porous Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ glass-ceramics were approximately 0.2 μm and 50 m²/g, respectively. The electrical conductivity of the porous glass-ceramics after heating in LiNO₃ aqueous solution was 8 × 10⁻⁵ S/cm at 300 K or 2 × 10⁻² S/cm at 600 K.     

Low Temperature Coefficient of Resonance Frequency Composition in the System Pb(Zr,Ti)O3—Pb(Mn1/3 Nb2/3)O3

Pb(Zr,Ti)O₃–Pb(Mn_1/3 Nb_2/3)O₃ (PZT–PMnN) system has been studied for high-power piezoelectric applications. This study investigates this system to find out the composition with high-power density piezoelectric characteristics and low tem-perature coefficient of resonance frequency (TCF). It was found that the composition 0.9PZT–0.1PMnN (Zr/Ti = 0.51/0.49) modified with 6 mol% Sr exhibits a TCF of −8 ppm/°C (−20 to +80°C). Further, the dielectric and piezoelectric properties of this composition are as follows: k _p= 0.53; Q _m= 800; d ₃₃= 274; ε₃₃/ε₀= 1290 and tan δ=1.1%, which shows the suitability of this composition for ultrasonic devices used under fluctuating thermal environment.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Synthesis of 0.4Pb(Mg1/3Nb2/3)O3–0.3Pb(Mg1/2W1/2)O3–0.3PbTiO3 Ceramics by Metal Alkoxide Method, and Its Dielectric Properties

0.4Pb(Mg_1/3Nb_2/3)O₃–0.3Pb(Mg_1/2W_1/2)O₃–0.3PbTiO₃+ x MgO ( x = 0 to 0.04) were prepared by a metal alkoxide method. The percent of perovskite phase of the calcined powders increased with increased calcination temperatures. About 89% of perovskite phase was obtained at 1050°C. The dielectric constant of the pellets fired at 1100°C was increased by the addition of 10 wt% excess Mg(OC₂H₅)₂ and had a maximum value of 7532 at 1 kHz.     

Formation and Structural Characterization of 1:1 Ordered Perovskites in the Ba(Zn1/3Ta2/3)O3–BaZrO3 System

The phase stabilities in the(1−x)Ba(Zn_1/3Ta_2/3)O₃ (BZT)-xBaZrO₃(BZ)system have been investigated using samples prepared by the mixed oxide method. The substitution of Zr⁴⁺destabilizes the 1:2 cation ordering in BZT and pro-motes the formation of a cubic, 1:1 ordered structure with a doubled perovskite repeat. The homogeneity range of the 1:1 phase extends from x = 0.04 to approximately x = 0.25; substitutions beyond this range stabilize a disordered perovskite. The limits of stability of the 1:1 ordering coin-cide with compositions previously found to exhibit anoma-lies in their dielectric loss. The range of homogeneity is consistent with a "random layer" model for the 1:1 ordered "Ba{β';_1/2β^1/2}O₃" structure. In this model the B× positions are assumed to be occupied exclusively by Ta⁵⁺, and the b× sites by a random distribution of Zn₂₊, Zr₄₊, and the remaining Ta 5+ cations. The validity of the model, where the ordered solid solutions can be represented by Ba{[Zn_{2− y /3}Ta_{(1−2 y )/3}Zr y ]_1/2[Ta]_1/2}O₃(y =2x)was con-firmed by Rietveld refinements conducted using data col-lected with a synchrotron X-ray source.     

Piezoelectric Properties of Pb[Zr0.45Ti0.5-xLux(Mn1/3Sb2/3)0.05]O3 Ceramics

The piezoelectric properties of Pb[Zr_0.45Ti_{0.5- x} Lu _x (Mn_1/3-Sb_2/3)_0.05]O₃ ceramics, with 0 lessthan equal to x lessthan equal to 0.03, have been investigated. The partial substitution of Ti⁴⁺ with Lu³⁺ permitted improvement of the electromechanical coupling factor ( k _p), the dielectric constant (epsilon^T₃₃), and the piezoelectric constant ( d ₃₃), while the dielectric loss (tan delta) increased and the mechanical quality factor ( Q _m) decreased with an increase of x . A pertinent piezoelectric material for actuator applications was Pb[Zr_0.45Ti_0.48Lu_0.02(Mn_1/3Sb_2/3)_0.05]O₃, and the piezoelectric properties were k _p = (58.5 ± 0.5)%, epsilon^T₃₃ = 32 ± 25, d ₃₃ = (373 ± 6) 10^-12 C/N, Q _m = 714 ± 22, and tan delta = (0.98 ± 0.03)%.     

Phase Relations in the Na0.5Bi0.5TiO3–Li3xLa(2/3)−x□(1/3)−2xTiO3 System

The phase relations and the mechanism of solid-state synthesis for the Na_0.5Bi_0.5TiO₃–Li_{3 x} La_{(2/3)− x} □_{(1/3)−2 x} TiO₃ system were investigated using X-ray powder diffraction, scanning electron microscopy, and thermal analysis. The study revealed that the extent of the homogeneity range—which is related to the A-site substitution between (Na_0.5Bi_0.5)²⁺ and (Li_{3 x} La_{(2/3)− x} □_{(1/3)−2 x} )²⁺ pseudo cations of a perovskite structure—depends strongly on the ordering of the (Li_{3 x} La_{(2/3)− x} □_{(1/3)−2 x} )²⁺ species. The solid-state reaction of the compounds in the homogeneity range is completed only after multiple high-temperature firings. However, the system is also subjected to a slow thermal decomposition; this is particularly so for the compounds with a high × value and an increased Li_{3 x} La_{(2/3)− x} □_{(1/3)−2 x} TiO₃ concentration.     

Structure and Dielectric Properties of Pb(Sc2/3W1/3)O3–Pb(Zr/Ti)O3 Relaxors

The structure and dielectric properties of (1− x )Pb(Sc_2/3W_1/3)O₃–( x )Pb(Zr/Ti)O₃ ceramics have been investigated over a full substitution range. All compositions with x < 0.5 adopt a cubic perovskite structure; however, for x ≤ 0.25 a doubled cell results from a 1:1 ordered distribution of the B-site cations. The structural order in Pb(Sc_2/3W_1/3)O₃ (PSW) can be described by a random-site model with one cation site occupied by Sc³⁺ and the other by a random distribution of (Sc_1/3³⁺W_2/3⁶⁺). The ordering is destabilized in solid solutions of PSW with PbZrO₃ (PSW–PZ), but stabilized by PbTiO₃ in the (1− x )PSW–( x )PT system. The changes in order are accompanied by alterations in the dielectric response of the two systems. For PSW–PZ the temperature of the permittivity maximum ( T _ɛ,max) increases linearly with x ; however, for PSW–PT T _ɛ,max decreases in the ordered region (up to x = 0.25) and then increases rapidly as the order is lost. Similar effects were produced by modifying the degree of order of (0.75)PSW–(0.25)PT; when the order parameter was reduced from ∼1.0 to ∼0.65, T _ɛ,max increased by more than 60°C.     

Electromechanical Properties of Pb(Yb1/2Nb1/2)O3-PbZrO3-PbTiO3 Ceramics

The electromechanical and electric-field-induced strain properties of x Pb(Yb_1/2Nb_1/2)O₃· y PbZrO₃·(1− x − y )PbTiO₃ ( x = 0.12, 0.25, 0.37; y = 0.10–0.40) ceramics have been studied systematically as a function of Pb(Yb_1/2Nb_1/2)O₃ (PYN) content and PbZrO₃/PbTiO₃ (PZ/PT) ratio. In addition, the effect of MnO₂ on the electromechanical properties of 0.12Pb(Yb_1/2Nb_1/2)O₃·0.40PbZrO₃·0.48PbTiO₃ was also investigated. The maximum transverse strain values of 1.6 × 10⁻³ for x = 0.12, 1.45 × 10⁻³ for x = 0.25, and 1.36 × 10⁻³ for x = 0.37 were obtained at the compositions which were regarded as the morphotropic phase boundary (MPB). The transverse strain was maximized at the MPB composition. The value of the maximum electromechanical coupling coefficient was 0.69 for y = 0.40 and x = 0.12 composition. In the 0.12Pb(Yb_1/2Nb_1/2)O₃·0.40PbZrO₃·0.48PbTiO₃ composition, the temperature of the maximum dielectric constant decreased and the grain size increased with an addition of MnO₂. The electromechanical coupling coefficient decreased while the mechanical quality factor rapidly increased with an addition of MnO₂. These resulted mainly from the acceptor effect of manganese ions that were produced by doping MnO₂ into the perovskite structure.     

Adhesive-Bonded Ca(Mg1/3Nb2/3)O3/Ba(Zn1/3Nb2/3)O3 Layered Dielectric Resonators with Tunable Temperature Coefficient of Resonant Frequency

Ca(Mg_1/3Nb_2/3)O₃ and Ba(Zn_1/3Nb_2/3)O₃ ceramic cylinders with the same diameter were bonded by adhesive with low dielectric loss to yield the layered dielectric resonators, and the microwave dielectric characteristics were evaluated with TE_01δ mode. With increasing the Ba(Zn_1/3Nb_2/3)O₃ thickness fraction, the resonant frequency ( f ₀) decreased, while the effective dielectric constant (ɛ _{r ,eff}) and temperature coefficient of resonant frequency (τ _f ) increased. Good microwave dielectric characteristics were attained for the samples with the Ba(Zn_1/3Nb_2/3)O₃ thickness fraction of 0.5: ɛ _{r ,eff}=34.33, Q × f =57 930 GHz and τ _f =2.6 ppm/°C. Finite-element method was used to predict the microwave dielectric characteristics of the layered resonators and good agreements were attained between the experimental results and predicted ones. Also, both experiment and finite-element analysis indicated that the effects of the adhesive on f ₀, ɛ _{r ,eff}, and τ _f were slight, while that on Q × f value was significant.     

Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Perovskite Phase Formation in the Relaxor System [Pb(Fe1/2Nb1/2)O3]1-x–[Pb(Zn1/3Nb2/3)O3]x

Phase formation and dielectric properties of the compositions in the system [Pb(Fe_1/2Nb_1/2)O₃]₁_ _x –[Pb(Zn_1/3Nb_2/3)O₃] _x were investigated as possible materials for multilayer ceramic capacitors. The formation of the phase with perovskite structure and dielectric properties of ceramics at room temperature in the entire composition range are presented. The undesirable pyrochlore phase can be suppressed up to x = 0.6 by adopting calcination of B-site oxides, followed by reaction with PbO. Compositions in the single-phase range can be sintered at less than 1000°C.     

Studies in Lithium Oxide Systems: II, Li2O Al2O3–Al2 O 3

Solid-state reactions between Li₂O and Al₂ O₃ were studied in the region between Li₂O.Al₂ O ₃ and Al₂ O ₃. The compound Li₂ O Al₂ O ₃ melts at 1610°± 15°C. and undergoes a rapid reversible inversion between 1200° and 1300°C. Vaporization of Li₂ O from compositions in the system proceeds at an appreciable rate at 1400°C, as shown by fluorescence. Lithium spinel, Li₂ O -5Al₂O₃, was the only other compound observed. The effect of Li₂ O on the sintering of alumina was investigated.     

High Piezoelectric and Dielectric Properties of La-Doped 0.3Pb(Zn1/3Nb2/3)O3–0.7Pb(ZrxTi1−x)O3 Ceramics Near Morphotropic Phase Boundary

La-doped 0.3Pb(Zn_1/3Nb_2/3)O₃–0.7Pb(Zr _x Ti_{1− x} )O₃ ( x =0.5–0.53) piezoelectric ceramics with pure perovskite phase were synthesized by a two-step hot-pressing route. The piezoelectric properties of various compositions near the morphotropic phase boundary (MPB) were systematically investigated. Not only was the exact MPB of this system determined via X-ray diffractometry analysis, but also the peak of piezoelectric properties was found near the MPB. The optimum piezoelectric properties of this series were observed in the specimen with Zr/Ti=51/49. The piezoelectric coefficient ( d ₃₃) and electromechanical coupling factor ( k _p) were 845 pC/N and 0.70, respectively, which have not been reported in this system so far. Large permittivity (ɛ_r=4088) and permittivity maximum (ɛ_m=29 500) were also obtained for the poled specimens. The temperatures ( T _max) of the permittivity maxima ranged from 206° to 213°C with various Zr/Ti ratios.     

Processing and Electrical Properties in Lead-Based (Pb(Mg1/3Nb2/3)O3, Pb(Yb1/2Nb1/2)O3, PbTiO3) Systems

Lead-based ferroelectric (FE) ceramics exhibit superior electromechanical properties; therefore, there has been an increased focus on developing new lead-based FE materials with high Curie temperature ( T _c) and enhanced properties. The aim of this study was to investigate new compositions in the Pb(Mg_1/3Nb_2/3)O₃–Pb(Yb_1/2Nb_1/2)O₃–PbTiO₃ ( PMN–PYbN–PT) system to enhance the electromechanical properties while increasing the T _c and lowering the sintering temperature. The 0.575[0.5PMN–0.5PYbN]–0.425PT composition at PMN/PYbN (50/50) mole ratio were prepared by reactive sintering PMNT and PYbNT powder mixtures at 950°–1200°C for 4 h. PMNT and PYbNT powders were calcined via the columbite method. Samples were prepared by cold isostatic pressing at 80 MPa. Dense and fully perovskite 0.575[0.5PMN–0.5PYbN]–0.425PT ceramics were fabricated at 975°C for 4 h, and these samples displayed a remnant polarization ( P _r) of 32 μ C/cm², coercive field ( E _c) of 17 kV/cm, and a piezoelectric charge coefficient ( d ₃₃) of 475 pC/N. It is proposed that this ternary system can be tailored for various applications.     

Ferroelectric 90° Domain Evaluation in Tetragonal Pb(Mg1/3Nb2/3)O3–PbTiO3 Ceramics

The domain structure of ferroelectrics changes during poling has a direct influence on the macroscopic properties of the materials. The intensity variation of the different X-ray diffraction (XRD) pattern profiles was used to identify the percentage of 90° domain reorientation in the tetragonal phase of Pb(Mg_1/3Nb_2/3)O₃–PbTiO₃ (PMN–PT) ceramics after poling. The results are consistent with the change of piezoelectric properties. In addition, by using XRD patterns, a spatial distribution of polarization in a well-poled 0.62PMN–0.38PT ceramics has been determined and was found to be best described by the Cauchy function W _00l (φ)=1/(1+0.023φ²).