Study on mechanical properties and material distribution of sandwich plaques molded by co‐injection

In the sandwich injection molding process (co‐injection), two different polymer melts are sequentially injected into a mold to form a part with a skin/core structure. Sandwich molding can be used for recycling, improving barrier and electrical properties, or producing parts with tailored mechanical properties. In this study the evaluation of flexural modulus and impact strength of co‐injected plaques have been investigated. Virgin and short glass fiber reinforced (10 and 40%) polypropylene were used in six different combinations of sandwiched layers. The skin and core thicknesses were measured by optical microscopy and used to calculate the theoretical flexural modulus, which was compared to the experimentally measured modulus. Fiber orientation states were also observed by scanning electronic microscopy (SEM) at some specific locations and their effect on mechanical properties discussed. The experimental results indicate that an important improvement in transverse modulus, near the gate, is obtained when the virgin polypropylene (PP) is used as a skin and 40% short glass fiber polypropylene (PP40) as core. When both skin and core are made of PP40, the flexural moduli are slightly higher than conventionally injected PP40. POLYM. COMPOS. 26:265–275, 2005. © 2005 Society of Plastics Engineers.     

Mechanical properties of glass fiber reinforced polypropylene injection molded with a rotation mold

A special mold (Rotation, Compression, and Expansion Mold) was used to impose a controlled shear action during injection molding of short glass fiber reinforced polypropylene discs. This was achieved by superimposing an external rotation to the pressure‐driven advancing flow front during the mold filling stage. Central gated discs were molded with different cavity rotation velocities, inducing distinct levels of fiber orientation through the thickness. The mechanical behavior of the moldings was assessed, in tensile and flexural modes on specimens cut at different locations along the flow path. Complete discs were also tested in four‐point flexural and in impact tests. The respective results are analyzed and discussed in terms of relationships between the developed fiber orientation level and the mechanical properties. The experimental results confirm that mechanical properties of the moldings depend strongly on fiber orientation and can thus be tailored by the imposed rotation during molding. POLYM. ENG. SCI. 46:1598–1607, 2006. © 2006 Society of Plastics Engineers.     

Microstructure and fracture behavior of (co)injection‐molded polyamide 6 composites with short glass/carbon fiber hybrid reinforcement

The mechanical and fracture properties of injection molded short glass fiber)/short carbon fiber reinforced polyamide 6 (PA 6) hybrid composites were studied. The short fiber composites of PA 6 glass fiber, carbon fiber, and the hybrid blend were injection molded using a conventional machine whereas the two types of sandwich skin–core hybrids were coinjection molded. The fiber volume fraction for all formulations was fixed at 0.07. The overall composite density, volume, and weight fraction for each formulation was calculated after composite pyrolysis in a furnace at 600°C under nitrogen atmosphere. The tensile, flexural, and single‐edge notch‐bending tests were performed on all formulations. Microstructural characterizations involved the determination of thermal properties, skin–core thickness, and fiber length distributions. The carbon fiber/PA 6 (CF/PA 6) formulation exhibits the highest values for most tests. The sandwich skin‐core hybrid composites exhibit values lower than the CF/PA 6 and hybrid composite blends for the mechanical and fracture tests. The behaviors of all composite formulations are explained in terms of mechanical and fracture properties and its proportion to the composite strength, fiber orientation, interfacial bonding between fibers and matrix, nucleating ability of carbon fibers, and the effects of the skin and core structures. Failure mechanisms of both the matrix and the composites, assessed by fractographic studies in a scanning electron microscope, are discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 957–967, 2005     

Effect of packing pressure on fiber orientation in injection molding of fiber‐reinforced thermoplastics

Injection molding of fiber‐reinforced polymeric composites is increasing with demands of geometrically complex products possessing superior mechanical properties of high specific strength, high specific stiffness, and high impact resistance. Complex state of fiber orientation exists in injection molding of short fiber reinforced polymers. The orientation of fibers vary significantly across the thickness of injection‐molded part and can become a key feature of the finished product. Improving the mechanical properties of molded parts by managing the orientation of fibers during the process of injection molding is the basic motivation of this study. As a first step in this direction, the present results reveal the importance of packing pressure in orienting the fibers. In this study, the effects of pressure distribution and viscosity of a compressible polymeric composite melt on the state of fiber orientation after complete filling of a cavity is considered experimentally and compared with the simulation results of Moldflow analysis. POLYM. COMPOS. 28:214–223, 2007. © 2007 Society of Plastics Engineers     

Fatigue performance of injection‐molded short e‐glass fiber reinforced polyamide‐6,6. II. Effects of melt temperature and hold pressure

Tensile and fatigue properties of an injection molded short E‐glass fiber reinforced polyamide‐6,6 have been studied as a function of two key injection molding parameters, namely melt temperature and hold pressure. It was observed that tensile and fatigue strengths of specimens normal to the flow direction were lower than that in the flow direction, indicating inherent anisotropy caused by injection molding. Tensile and fatigue strengths of specimens with weld line were significantly lower than that without weld lines. For specimens in the flow direction, normal to the flow direction and with weld line, tensile strength and fatigue strength increased with increasing melt temperature as well as increasing hold pressure. The effect of specimen orientation on the tensile and fatigue strengths is explained in terms of the difference in fiber orientation and skin‐core morphology of the specimens. POLYM. COMPOS., 2011. © 2010 Society of Plastics Engineers.     

A comparison of short glass fiber reinforced polypropylene plates made by conventional injection molding and using shear controlled injection molding

This paper describes a comparison of the fiber orientation structures and resulting elastic properties of samples of short glass fiber filled polypropylene made by conventional injection molding and by the SCORIM (Shear Controlled Orientation in Injection Molding) process developed at The University of Brunel. The 3D fiber orientation distributions of the composites were measured using a unique transputer based image analysis system developed at The University of Leeds. The mechanical properties of the samples were characterized using an ultrasonic velocity technique, which allows a full set of elastic constants to be determined for each material. The link between fiber orientation distributions and measured elastic properties was then investigated using theoretical models developed in this laboratory.     

Fiber orientation in divergent/convergent flows in expansion and compression injection molding

This study compares the fiber orientation patterns of short glass fiber‐reinforced polypropylene developed in conventional and nonconventional injection molding, the latter using a special mold, RCEM (rotation, compression, and expansion mold). This mold allows for a wide variety of operating modes during mold filling, which leads to a great versatility in obtaining different fiber orientation patterns. By incorporating through‐thickness convergent and divergent flows during the filling stage (compression and expansion modes, respectively), the fiber orientation can be tailored. These linear dynamics can be superimposed with a simultaneous rotational movement of one of the mold surfaces. These combined actions induce a high fiber orientation transversely to the radial flow direction, this effect being more pronounced in the expansion mode. POLYM. COMPOS. 27:539–551, 2006. © 2006 Society of Plastics Engineers     

Injection molding of glass fiber reinforced phenolic composites. 2: Study of the injection molding process

This study of injection molding of glass fiber reinforced phenolic molding compounds examines fiber breakage and fiber orientation with key material and processing variables, such as injection speed, fiber volume fraction, and the extent of resin pre-cure. The fiber orientation, forming discrete skin-core arrangements, is related to the divergent gate to mold geometrical transition, the extent of pre-cure and injection speed functions of the melt viscosity. Transient modifications to the melt viscosity during mold filling produce variations in skin/core structure along the flow path, which are correlated to the mechanical properties of injection moldings. The melting characteristics of the phenolic resin during plasticization impose a severe environment of mechanical attrition on the glass fibers, which is sequentially monitored along the screw, and during subsequent flow through runners and gates of various sizes. Differences found between the processing characteristics of thermosets and thermoplastics raise questions concerning the applicability of thermoplastic injection molding concepts for thermosets.     

Optimization of fiber prediction model coefficients in injection molding simulation based on micro computed tomography

Fiber‐reinforced thermoplastic for low weight application become increasingly important for many industrial branches. During the injection molding of short fiber‐reinforced thermoplastic parts the fibers become orientated. This orientation is determined on the one hand by the geometry of the part, and on the other hand by the injection molding parameters, and influence the mechanical behavior of the part. The determination of the fiber properties that is, the orientation distribution of the fibers, is therefore of considerable interest. Since a more accurate fiber orientation prediction of the injection molding simulation will lead to a more precise structural simulation the objective of the present work is to achieve a preferably accurate orientation distribution. To describe the orientation distribution of the fibers, the fiber orientation tensor defined by Advani and Tucker (Advani and Tucker, Journal of Rheology, 31, 751 (1987)) was used. To determine the entries of this tensor micro computed tomography scans (μCT‐scans) of an injection‐molded plate, as well as an injection‐molded specimen with different cross section and shape were performed. Injection molding simulation using Autodesk Moldflow Insight were carried out. The residual strain closure (RSC) model was the underlying model to depict the fiber orientation distribution, or rather the orientation tensors. The two model parameters, the fiber interaction coefficient Ci and the scalar factor κ , were adapted by an optimization procedure, in such a way that the orientation distributions of the simulations fit the results of the μCT‐analysis at its best. POLYM. ENG. SCI., 59:E152–E160, 2019. © 2018 Society of Plastics Engineers     

不饱和聚酯片状模塑料力学性能的研究

研究了玻纤布、短切玻纤及碳酸钙对不饱和聚酯片状模塑料力学性能的影响,实验发现:玻纤布增强不饱和聚酯片状模塑料的力学性能比短切玻纤好,随着玻纤含量的增加,不饱和聚酯片状模塑料的拉伸强度先增加,达到一极大值之后减少。碳酸钙填充不饱和聚酯片状模塑料,随着碳酸钙含量的增加,不饱和聚酯片状模塑料的拉伸强度明显降低,弯曲强度增加。     

Mechanical Properties of Carbon Epoxy Prepreg Insert Phenolic Resin Injection Moldings

This study focuses on the insert-injection molding process. The thermoset composite inserts in this study were carbon fiber/epoxy(CF/Epoxy) prepreg sheets. The injected molded part was glass fiber contained phenolic resin(GF/PF). The CF/Epoxy was placed in the mold cavity prior to injecting GF/PF onto the inserted injection molded CF/Epoxy specimens. The role of adhesion between the inserted part and injected resin on the mechanical properties was evaluated by 3 point bending and impact tests. In addition, the effect of prepreg orientation on the mechanical properties of the prepreg inserted-injection molding system was investigated. It was found that the prepreg with unidirectional orientation significantly improved flexural and impact strength of the inserted injection molding composites, providing better support and resistance to bending and impact loading. The main failure modes of the specimens were structural and adhesive failure.     

动态注射成型短玻纤增强高密度聚乙烯力学性能的研究

在不同的振动条件下注射成型短玻纤增强高密度聚乙烯复合材料。实验表明,振动可以有效地改善玻纤在树脂基体中的分散取向状况,提高复合材料的力学性能。与稳态注射成型的复合材料相比,动态注射成型复合材料的拉伸强度最大可提高11.1%,冲击强度最大可提高11.4%。     

Mechanical properties of injection‐molded short‐fiber thermoplastic composites. Part 1: The elastic moduli and strengths of glass‐filled poly(butylene terephthalate)

The effects of processing and part geometry on the local mechanical properties of injection‐molded, 30 wt% short‐fiber‐reinforced filled poly(butylene terephthalate) (PBT) are characterized by mechanical tests on specimens cut from rectangular plaques of different thicknesses injection molded at several different processing conditions. Stiffness data from tensile tests at 12.7‐mm intervals on 12.7‐mm‐wide strips cut from injection‐molded plaques—both along the flow and cross‐flow directions—and flexural tests on these strips show consistency of plaque‐to‐plaque local properties. Also, in addition to the well‐known anisotropic properties caused by flow‐induced fiber orientation, injection‐molded short fiber composites exhibit in‐plane and through‐thickness nonhomogeneity—as indicated by in‐plane property variations, by differences between tensile and flexural properties, and by the flexural strength being significantly higher than the tensile strength. The sensitivity of these mechanical properties to process conditions and plaque geometry have also been determined: the flow‐direction tensile modulus increases with fill time, the differences between flow and cross‐flow properties decrease with increasing thickness, and both the flow and cross‐flow flexural moduli decrease with increasing plaque thickness. While the flexural modulus is comparable to the tensile modulus, the flexural strength is significantly higher than the tensile strength. POLYM. COMPOS., 26:428–447, 2005. © 2005 Society of Plastics Engineers     

Fabrication of long glass fiber reinforced polyacetal composites: Mechanical performance,microstructures, and isothermal crystallization kinetics

A thermoplastic pultrusion was carried out to prepare the long fiber reinforced thermoplastic (LFT) composites based on polyacetal (POM) matrix on the custom‐designed pultrusion equipment. The investigation on mechanical performance revealed that the POM‐based LFT composites achieved much higher tensile, flexural, and impact strength than the short glass fiber reinforced ones at the same fiber loadings. Such a promising reinforcement effect is attributed to the feature that the residual fiber length in the injection‐molded LFT products is greatly superior to that in short fiber reinforced ones. This takes full advantage of the strength of the reinforcing fiber itself. The scanning electronic microscopy demonstrated that the fiber fracture and fiber pull‐out concurred on the tensile and impact fracture surfaces, and the former preceded the latter. The isothermal crystallization kinetics of the POM‐based LFT composites was also intensively studied, and the results indicated that the crystallinity of POM domain was enhanced by the heterogeneous nucleation of glass fiber, but the crystallization rate was postponed due to the interspace restriction toward crystalline growth caused by long glass fiber. These kinetic parameters provided information on the processing conditions of POM‐based LFT composites for the injection and compression molding. POLYM. COMPOS., 36:1826–1839, 2015. © 2014 Society of Plastics Engineers     

基于Mori⁃Tanaka方法的短纤维复合材料开孔板分析

基于Mori?Tanaka均匀化方法,对短纤维复合材料开孔板力学性能进行研究。首先,使用Mori?Tanaka方法预测单向和二维2种分布形式的短纤维复合材料应力?应变曲线曲线。其次,通过试验方法分析不同区域纤维取向对开孔板力学性能的影响。最后,使用多尺度方法研究不同注塑位置和不同开孔方式对开孔板力学性能的影响,该部分在宏观有限元分析中耦合了注塑模拟的纤维方向分布以及Mori?Tanaka均匀化方法得到的复合材料参数。结果表明,短边注塑开孔板综合力学性能更好;孔周围纤维分布是影响应力集中的主要因素;整体的纤维取向分布影响开孔板的刚度;单向纤维材料的角度对材料性能的影响不是单调的。     

Mechanical properties of injection molded long fiber polypropylene composites,Part 1: Tensile and flexural properties

Innovative polymers and composites are broadening the range of applications and commercial production of thermoplastics. Long fiber‐reinforced thermoplastics have received much attention due to their processability by conventional technologies. This study describes the development of long fiber reinforced polypropylene (LFPP) composites and the effect of fiber length and compatibilizer content on their mechanical properties. LFPP pellets of different sizes were prepared by extrusion process using a specially designed radial impregnation die and these pellets were injection molded to develop LFPP composites. Maleic‐anhydride grafted polypropylene (MA‐g‐PP) was chosen as a compatibilizer and its content was optimized by determining the interfacial properties through fiber pullout test. Critical fiber length was calculated using interfacial shear strength. Fiber length distributions were analyzed using profile projector and image analyzer software system. Fiber aspect ratio of more than 100 was achieved after injection molding. The results of the tensile and flexural properties of injection molded long glass fiber reinforced polypropylene with a glass fiber volume fraction of 0.18 are presented. It was found that the differences in pellet sizes improve the mechanical properties by 3–8%. Efforts are made to theoretically predict the tensile strength and modulus using the Kelly‐Tyson and Halpin‐Tsai model, respectively. POLYM. COMPOS., 28:259–266, 2007. © 2007 Society of Plastic Engineers     

Formation mechanism of high-pressure water penetration induced fiber orientation in overflow water-assisted injection molded short glass fiber-reinforced polypropylene

Recently, there has been growing interest in water-assisted injection molding (WAIM) not only for its advantages over gas-assisted molding (GAIM) and conventional injection molding (CIM), but also for its great potential advantages in industrial applications. To understand the formation mechanism of water penetration induced fiber orientation in overflow water-assisted injection molding (OWAIM) parts of short glass fiber-reinforced polypropylene (SGF/PP), in this work, the external fields and water penetration process within the mold cavity were investigated by experiments and numerical simulations. The results showed that the difference of fiber orientation distribution in thickness direction between WAIM moldings and CIM moldings was mainly ascribed to the great external fields generated by water penetration. Besides, fiber orientation depended on the position both across the part thickness and along the flow direction. Especially in the radial direction, fiber orientation varied considerably. The results also showed that the melt temperature is the principal parameter affecting the fiber orientation along the flow direction, and a higher melt temperature significantly facilitated more fibers to be oriented along the flow direction, which is quite different from the results as previously reported in short-shot water-assisted injection molding (SSWAIM). A higher water pressure, shorter water injection delay time, and higher melt temperature significantly induced more fibers to be orderly oriented in OWAIM moldings, which may improve their mechanical performances and broaden their application scope.     

Manufacturing and testing of long basalt fiber reinforced thermoplastic matrix composites

In this work, long basalt fiber reinforced composites were investigated and compared with short basalt fiber reinforced compounds. The results show that long fiber reinforced thermoplastic composites are particularly advantageous in the respects of dynamic mechanical properties and injection molding shrinkage. The fiber orientation in long basalt fiber reinforced products fundamentally differs from short basalt fiber reinforced ones. This results in more isotropic molding shrinkage in case of long basalt fiber reinforced composites. The main advantage of the used long fiber thermoplastic technology is that the special long fiber reinforced pellet can be processed by most conventional injection molding machines. During extrusion compounding the fibers in the compound containing 30 wt% fibers are fragmented to an average length of 0.48 mm (typical of short fiber reinforced thermoplastic compounds), this length decreases further during injection molding to 0.20 mm. Contrarily using long fiber reinforced pellets and cautious injection molding parameters, an average fiber length of 1.8 mm can be achieved with a conventional injection molding machine, which increased the average length/diameter ratio from 14 to 130. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Fiber orientation in injection molding with rotating flow

The development of fiber orientation in injection molding was manipulated by a special molding tool, the RCEM mold, which imposes a rotation action by one of the cavity surfaces during the filling stage. Center‐gated disc moldings were produced from glass fiber reinforced polypropylene with different cavity rotation velocities, inducing distinct distributions and levels of fiber orientation. The morphologies of the moldings were characterized by optical and electronic microscopy. The through‐thickness profiles of fiber orientation were assessed by means of the orientation tensor, and the relationship between the processing thermo‐mechanical environment and the fiber orientation was established. At high rotation velocities, the resulting fiber orientation pattern is mainly controlled by the rotational motion, inducing a much more homogeneous through‐the‐thickness fiber orientation distribution, with a preferential alignment on the circumferential direction. POLYM. ENG. SCI., 2008. © 2007 Society of Plastics Engineers     

Fiber orientation structures and mechanical properties of injection molded short glass fiber reinforced ribbed plates

In this paper we describe a study of the fiber orientation structures present within a model ribbed injection molded plate. The details of the fiber orientation at each chosen location on the injection molded parts were measured using an in-house developed image analysis system, which enabled large areas to be scanned (up to 200 mm²) up to a limit of 1 million fiber images. Two materials were used for these experiments, short glass fiber filled PBT and short glass fiber filled nylon 66. First, a comparison was made between the fiber orientation at an identical position, 28 mm from the injection gate on a transverse rib, on two plates made from glass fiber filled PBT. It was found that the fiber orientation in these two separately manufactured components was virtually identical when comparing the whole scanned area, but the differences became more significant when comparing areas on the length scale of an individual fiber (∼ 200 μm). Second, the fiber orientation at the same position was compared for two plates made using the glass/PBT and glass/nylon 66 materials. The differences for the complete scanned areas were small, confirming that mold geometry plays a crucial role in determining fiber orientation structures, and that matrix properties are secondary. Third, the fiber orientation structures at various positions across one of the glass/PBT plates were examined in greater detail, in particular across a number of the transverse ribs: the chosen ribs were of various widths and heights. Differences in structure were found depending on the local rib geometry. Finally, the effect of the measured fiber orientation structures in determining the mechanical properties of the ribbed plate was investigated using simple modeling schemes. While the stiffness of the rib/web assembly was found to depend on the average fiber orientation of the two parts, the different thermal expansions of the web and the rib, caused by the different fiber orientation in the two regions, led to significant warpage of the rib/web assembly. Polym. Compos. 25:237–254, 2004. © 2004 Society of Plastics Engineers.