Fracture toughness and impact strength of anhydride‐cured biobased epoxy

Biobased neat epoxy materials containing functionalized vegetable oils (FVO), such as epoxidized linseed oil (ELO) and epoxidized soybean oil (ESO), were processed with an anhydride curing agent. A percentage of diglycidyl ether of bisphenol F (DGEBF) was replaced by ELO or ESO. The selection of the DGEBF, FVO, and an anhydride‐curing agent resulted in an excellent combination to produce a new biobased epoxy material having a high elastic modulus and high glass transition temperature. Izod impact strength and fracture toughness were significantly improved dependent on FVO content, which produced a phase‐separated morphology. POLYM. ENG. SCI., 45:487–495, 2005. © 2005 Society of Plastics Engineers     

Primary recycling of anhydride‐cured engineering epoxy using alcohol solvent

Recycling of engineering thermosets is extremely difficult for conventional techniques due to their crosslinked networks. In this study, we demonstrated a new recycling approach for anhydride‐cured engineering epoxy. After soaking the epoxy networks in alcohol solvent mixed with transesterification catalyst, both solvent and catalyst molecules diffused inside, broke the ester bonds on the chain backbone through bond exchange reactions, and eventually decomposed the networks. The ester covalent bonds would be reformed as evaporating the solvent, and the dissolved polymer solution was re‐polymerized into near‐identical networks. When compared with existing recycling approaches, the proposed one is advantageous for its low cost, zero pollution, low temperature (160°C), and ambient pressure during operation. Epoxy networks with different amount of anhydride cross‐linkers were synthesized, and the influences of solvent choice, network stoichiometry, and crosslinking density on the recycling rate were studied. Specifically, the dissolution rate of epoxy samples was evaluated by their weight loss in two types of alcohol solvents, and the re‐polymerization rate was evaluated by the increment of solution viscosity and network modulus. Thermomechanical properties of recycled epoxy were compared with those of native samples. Finally, the dissolution and re‐polymerization cycles were performed for multiple times to investigate the repeatability. POLYM. ENG. SCI., 59:E111–E119, 2019. © 2018 Society of Plastics Engineers     

Mechanical properties and failure surface morphology of amine‐cured epoxy/clay nanocomposites

The tensile and impact properties of amine‐cured diglycidyl ether of bisphenol A based nanocomposites reinforced by organomontmorillonite clay nanoplatelets are reported. The sonication processing scheme involved the sonication of the constituent materials in a solvent followed by solvent extraction to generate nanocomposites with homogeneous dispersions of the organoclay nanoplatelets. The microstructure of the clay nanoplatelets in the nanocomposites was observed with transmission electron microscopy, and the clay nanoplatelets were well dispersed and were intercalated and exfoliated. The tensile modulus of epoxy at room temperature, which was above the glass‐transition temperature of the nanocomposites, increased approximately 50% with the addition of 10 wt % (6.0 vol %) clay nanoplatelets. The reinforcing effect of the organoclay nanoplatelets was examined with respect to the Tandon–Weng and Halpin–Tsai models. The tensile strength was improved only when 2.5 wt % clay nanoplatelets were added. The Izod impact strength decreased with increasing clay content. The failure surfaces of the nanocomposites were observed with environmental scanning electron microscopy and confocal laser scanning microscopy. The roughness of the failure surface was correlated with the tensile strength. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 281–287, 2005     

Synthesis of rosin‐based flexible anhydride‐type curing agents and properties of the cured epoxy

BACKGROUND: Although rosin acid derivatives have received attention in polymer synthesis in recent years, to the best of our knowledge, they have rarely been employed as epoxy curing agents. The objective of the study reported here was to synthesize rosin‐based flexible anhydride‐type curing agents and demonstrate that the flexibility of a cured epoxy resin can be manipulated by selection of rosin‐based anhydride‐type curing agents with appropriate molecular rigidity/flexibility. RESULTS: Maleopimarate‐terminated low molecular weight polycaprolactones (PCLs) were synthesized and studied as anhydride‐type curing agents for epoxy curing. The chemical structures of the products were confirmed using ¹H NMR spectroscopy and Fourier transform infrared spectroscopy. Mechanical and thermal properties of the cured epoxy resins were studied. The results indicate that both the epoxy/anhydride equivalent ratio and the molecular weight of PCL diol play important roles in the properties of cured resins. CONCLUSION: Rosin‐based anhydride‐terminated polyesters could be used as bio‐based epoxy curing agents. A broad spectrum of mechanical and thermal properties of the cured epoxy resins can be obtained by varying the molecular length of the polyester segment and the epoxy/curing agent ratio. Copyright © 2009 Society of Chemical Industry     

Physico‐mechanical properties of nano‐polystyrene‐decorated graphene oxide–epoxy composites

Nano‐polystyrene (nPS)‐decorated graphene oxide (GO) hybrid nanostructures were successfully synthesized using stepwise microemulsion polymerization, and characterized using Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), field‐emission scanning electron microscopy and transmission electron microscopy. XRD and FTIR spectra revealed the existence of a strong interaction between nPS and GO, which implied that the polymer chains were successfully grafted onto the surface of the GO. The nPS‐decorated GO hybrid nanostructures were compounded with epoxy using a hand lay‐up technique, and the effect of the nPS‐decorated GO on the mechanical, thermal and surface morphological properties of the epoxy matrix was investigated using a universal tensile machine, Izod impact tester, thermogravimetric analysis and contact angle measurements with a goniometer. It was observed that in the epoxy matrix, GO improved the compatibility. © 2017 Society of Chemical Industry     

Synthesis and properties of methyl hexahydrophthalic anhydride‐cured fluorinated epoxy resin 2,2‐bisphenol hexafluoropropane diglycidyl ether

The fluorinated epoxy resin, 2,2‐bisphenol hexafluoropropane diglycidyl ether (DGEBHF) was synthesized through a two‐step procedure, and the chemical structure was confirmed by ¹H n uclear magnetic resonance (NMR), ¹³C NMR, and Fourier transform infrared (FTIR) spectra. Moreover, DGEBHF was thermally cured with methyl hexahydrophthalic anhydride (MHHPA). The results clearly indicated that the cured DGEBHF/MHHPA exhibited higher glass transition temperature (T_g 147°C) and thermal decomposition temperature at 5% weight loss (T₅ 372°C) than those (T_g 131.2°C; T₅ 362°C) of diglycidyl ether of bisphenol A (DGEBA)/MHHPA. In addition, the incorporation of bis‐trifluoromethyl groups led to enhanced dielectric properties with lower dielectric constant (D_k 2.93) of DGEBHF/MHHPA compared with cured DGEBA resins (D_k 3.25). The cured fluorinated epoxy resin also gave lower water absorption measured in two methods relative to its nonfluorinated counterparts. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2801–2808, 2013     

Viscoelastic behavior of anhydride‐cured epoxy system initiated by thermal latent catalyst

The thermal latency and viscoelastic behavior during the cure of a new catalytic (N‐benzylpyrazinium hexafluoroantimonate) anhydride‐cured epoxy system were studied with differential scanning calorimetry and a rheometer under isothermal conditions. The gelation time was obtained from the evaluation of the storage modulus, loss modulus, and damping factor. The temperature dependence on the reaction time was described by the Arrhenius expression, and the crosslinking activation energy was determined from the Arrhenius plot based on the gelation time and reaction temperature. The gelation time and crosslinking activation energy characterized from rheological behaviors increased with increasing anhydride composition and showed a maximum value with a mixing ratio of 0.65, which was due to the compact crosslinking network without a side reaction in the ratio. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 646–653, 2001     

Preparation and properties of nano‐Al2O3 particles/polyester/epoxy resin ternary composites

This article presents the results of an experimental study on the preparation and properties of new ternary composites composed of nano‐Al₂O₃ particles, polyester, and epoxy resin. The ternary composites were prepared by the addition of the nano‐Al₂O₃ particles in a binary matrix, with elevated viscosity, of the epoxy resin modified by the polyester. The nano‐Al₂O₃ particles were previously located and dispersed in the polyester phase. The study showed that the ternary system was a type of nanoscale dispersed composite with high strength and toughness as well as modulus, combined with excellent dielectric and heat‐resistance properties. All related properties of the composites were remarkably superior to those of both the binary matrix and the unmodified epoxy resin. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 70–77, 2002     

Viscoelastic properties of polypropylene/organo‐clay nano‐composites prepared using miniature lab mixing extruder from masterbatch

Polypropylene (PP) was melt blended with nano organo‐clay masterbatch at different ratios; namely 5, 10, and 15 wt % of nano‐clay. The effect of organo‐clay content on the viscoelastic properties of the nano‐composite was studied. A miniature laboratory mixing extruder, LME, was used to blend the nano organo‐clay masterbatch with PP at 260°C and 250 rpm. The blend was pelletized first, and then a thin ribbon was extruded. Two viscoelastic tests were performed; frequency sweep at constant temperature of 80°C, and temperature sweep at constant frequency of 1.0 rad/s. As the loading of nano‐clay increased, the storage modulus, G', and the thermal resistance increased as well. Different viscoelastic models were tried and 3‐elements Maxwell model was found to describe well the viscoelastic properties of the nano‐composites. The ratio of the complex modulus to the corresponding matrix modulus at different frequencies was found to vary proportional to the nanoclay loading. This dependency was described reasonably well by modified Guth model using particle aspect ratio of 12.1. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Viscoelastic behavior of epoxy/carbon fiber/Zno nano‐rods hybrid composites

The insufficient viscoelastic resistance of fiber reinforced plastics can be retrofitted by the addition of more rigid nano fillers to the polymer matrix. In this study, carbon fibers plies were grafted with zinc oxide (ZnO) nano‐rods and the hybridized reinforcement was utilized in laminated composites. Flexural creep tests were carried out using dynamic mechanical analysis (DMA) and the time/temperature superposition principle was employed for accelerated testing. To verify the applicability of TTPS, prolonged stress relaxation tests were also carried out in flexural mode. Data from the DMA flexural creep tests revealed that the whiskerization of carbon fibers with ZnO nano rods reduced the creep compliance by 23% at elevated temperatures and prolonged durations. Also, the relaxation data confirmed the applicability of TTPS to these hybrid composites. The stress relaxation modulus improved by 65% in comparison to composites based on neat carbon fibers. POLYM. COMPOS., 36:1967–1972, 2015. © 2014 Society of Plastics Engineer     

Thermal and mechanical properties of anhydride‐cured epoxy resins with different contents of biobased epoxidized soybean oil

Thermosetting resins were synthesized by the partial replacement of the synthetic epoxy prepolymer based on diglycidyl ether of bisphenol A (DGEBA) with increasing amounts of epoxidized soybean oil (ESO) with methyltetrahydrophthalic anhydride as a crosslinking agent and 1‐methyl imidazole as an initiator. Calorimetric studies showed a drop in the reaction heat with ESO content; this was associated with the lower reactivity of oxirane rings in ESO due to steric constrains. The effects of the replacement of increasing amounts of synthetic DGEBA with ESO on the network properties, such as the storage modulus (E′) in the glassy and rubbery regions, glass‐transition temperature (T_g), and impact and compressive properties were examined. All formulations were transparent, although phase‐separated morphologies were evidenced by scanning electron microscopy observations. The intensity of the transmitted light passed to a minimum at a short reaction time associated with the cloud point and then increased continuously until the refractive index of the dispersed phase approximated that of the continuous phase at complete conversion. The combination of DGEBA with 40 wt % ESO resulted in a resin with an optimum set of properties; E′ in the glassy state was 93% of that of the neat DGEBA resin, T_g decreased only about 11°C, and the impact strength increased about 38% without a loss of transparency. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The structure‐property relationship of novolac cured epoxy resin/clay nanocomposites

Intercalated or exfoliated novolac cured epoxy resin nanocomposites were prepared with two different kinds of layered silicates – montmorillonite (PK‐802) and nontronite (PK‐805). The bifunctional modifiers (PI/BEN or MI/BEN) are used to modify the clays for improvement of the properties of polymer where benzalkonium chloride (BEN) acts as a compatibilizing agent and 2‐phenylimidazole (PI) or 2‐methylimidazole (MI) as the accelerators. Both the compatibilizer and accelerator are simultaneously intercalated into the gallery space of pure clays to form the modified clay. The novolac cured epoxy nanocomposites are prepared with these modified clays by crosslinking polymerization reaction. The properties of novolac cured epoxy/clay nanocomposites were characterized by wide‐angle X‐ray diffraction (WAXD), thermo‐gravimetric analysis (TGA), dynamic mechanical analysis (DMA), and transmission electron microscopy (TEM) methods. According to the measurement, these novolac cured epoxy‐clay nanocomposites have been shown the significant improvement in the thermal, mechanical, and barrier properties that may be applied to make printed circuit board. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Study of dynamically cured PP/MAH‐g‐PP/talc/epoxy composites

In the present study, an epoxy resin was dynamically cured in a polypropylene (PP)/maleic anhydride–grafted PP (MAH‐g‐PP)/talc matrix to prepare dynamically cured PP/MAH‐g‐PP/talc/epoxy composites. An increase in the torque at equilibrium showed that epoxy resin in the PP/MAH‐g‐PP/talc composites had been cured by 2‐ethylene‐4‐methane‐imidazole. Scanning electron microscopy analysis showed that MAH‐g‐PP and an epoxy resin had effectively increased the interaction adhesion between PP and the talc in the PP/talc composites. Dynamic curing of the epoxy resin further increased the interaction adhesion. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had higher crystallization peaks than did the PP/talc composites. Thermogravimetric analysis showed that the addition of MAH‐g‐PP and the epoxy resin into the PP/talc composites caused an obvious improvement in the thermal stability. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best thermal stability of all the PP/talc composites. The PP/MAH‐g‐PP/talc/epoxy composites had better mechanical properties than did the PP/MAH‐g‐PP/talc composites, and the dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best mechanical properties of all the PP/talc composites, which can be attributed to the better interaction adhesion between the PP and the talc. The suitable content of epoxy resin in the composites was about 5 wt %. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Processing and properties of polymeric nano‐composites

Polymeric nano‐composites are prepared by melt intercalation in this study. Nano‐clay is mixed with either a polymer or a polymer blend by twin‐screw extrusion. The clay‐spacing in the composites is measured by X‐ray diffraction (XRD). The morphology of the composites and its development during the extrusion process are observed by scanning electron microscopy (SEM). Melt viscosity and mechanical properties of the composites and the blends are also measured. It is found that the clay spacing in the composites is influenced greatly by the type of polymer used. The addition of the nano‐clay can greatly increase the viscosity of the polymer when there is a strong interaction between the polymer and the nano‐clay. It can also change the morphology and morphology development of nylon 6/PP blends. The mechanical test shows that the presence of 5–10 wt.% nano‐clay largely increases the elastic modulus of the composites and blends, while significantly decreases the impact strength. The water absorption of nylon 6 is decreased with the presence of nano‐clay. The effect of nano‐clay on polymers and polymer blends is also compared with Kaolin clay under the same experimental conditions.     

Morphologies and properties of cured epoxy/brominated‐phenoxy blends

Morphologies of cured epoxy/brominated‐phenoxy blends were observed by scanning transmission electron microscopy (STEM) and energy dispersive X‐ray fluorescence spectroscopy (EDX). When brominated‐phenoxy content was 30 wt %, cocontinuous phase structures between cured epoxy and brominated‐phenoxy were found. Since every loss tangent (tan δ) curve as a function of temperature on dynamic mechanical analysis (DMA) showed 2 peaks at 128°C and 155°C respectively, cured epoxy phases and brominated‐phenoxy phases were incompatible together and T_gs of cured epoxy phases were not decreased. Tensile strength and tensile elongation of the cured blends were increased together. T‐peel adhesion strength and the lap‐shear adhesion strength were also increased together. These phenomena could be due to the cocontinuous structures consisted by the rigid cured epoxy phases of thermosets and ductile the brominated‐phenoxy phases of thermoplastics. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1702–1713, 2007     

Fabrication of functionally graded nano‐TiO2‐reinforced epoxy matrix composites

Functionally graded nano‐TiO₂ epoxy matrix composites were successfully fabricated using a centrifugal method. In the preparation of the composite, the aggregation of nano‐TiO₂ occurred during curing, which had a negative effect on the composite performance. To solve this problem, we introduced a silane coupling agent to modify the surface of the nano‐TiO₂, thereby improving the performance and mechanical properties simultaneously. The modified nano‐TiO₂ (s‐TiO₂) had better dispersion in the epoxy resin, making it possible to produce depth gradients of the mechanical properties of functionally graded materials (FGMs). The s‐TiO₂ was characterized with respect to functional groups, morphology, and chemical elements using transmission electron microscopy, X‐ray photoelectron spectroscopy, and Fourier‐transform infrared spectroscopy. The results show that a silane layer was successfully coated on the surface. Also, the gradients of the mechanical and permittivity properties of the FGM indicated that by modifying the surface of the nano‐filler, it is possible to fabricate nano‐filler‐reinforced epoxy matrix FGMs using a centrifugal method. POLYM. COMPOS., 35:557–563, 2014. © 2013 Society of Plastics Engineers     

Preparation and properties of nano‐CaCO3/acrylonitrile‐butadiene‐styrene composites

CaCO₃/acrylonitrile‐butadiene‐styrene (ABS) and CaCO₃/ethylene‐vinyl acetate copolymer (EVA)/ABS nanocomposites were prepared by melting‐blend with a single‐screw extruder. Mechanical properties of the nanocomposites and the dispersion state of CaCO₃ particles in ABS matrix were investigated. The results showed that in CaCO₃/EVA/ABS nanocomposites, CaCO₃ nanoparticles could increase flexural modulus of the composites and maintain or increase their impact strength for a certain nano‐CaCO₃ loading range. The tensile strength of the nanocomposites, however, was appreciably decreased by adding CaCO₃ nanoparticles. The microstructure of neat ABS, CaCO₃/ABS nanocomposites, and CaCO₃/EVA/ABS nanocomposites was observed by scanning electron microscopy. It can be found that CaCO₃ nanoparticles were well‐dispersed in ABS matrix at nanoscale. The morphology of the fracture surfaces of the nanocomposites revealed that when CaCO₃/EVA/ABS nanocomposites were exposed to external force, nano‐CaCO₃ particles initiated and terminated crazing (silver streak), which can absorb more impact energy than neat ABS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fabrication and properties of nano‐ZnO/glass‐fiber‐reinforced polypropylene composites

Polypropylene (PP) is widely used in many fields, such as automobiles, medical devices, office equipment, pipe, and architecture. However, its high brittle transformation temperature, low mechanical strength, dyeing properties, antistatic properties, and poor impact resistance, considerably limit its further applications. Nano‐ZnO treated by KH550 coupling agent and glass fibers (GFs) were introduced in order to improve the mechanical performance and flowability of PP in this research. The crystallization behavior and microstructure of nano‐ZnO/GFs/PP hybrid composites were analyzed by differential scanning calorimetry, transmission electron microscopy, and scanning electron microscopy. The effect of crystallization behavior on the mechanical properties of the nanocomposites was investigated and analyzed. The results indicated that nano‐ZnO surface‐coupled by KH550 could be uniformly dispersed in the PP matrix. The incorporation of nano‐ZnO and GFs resulted in increases of the crystallization temperature and crystallization rate of PP and a decrease of the crystallization degree. The introduction of nano‐ZnO and GFs also enhanced the tensile strength and impact toughness of the hybrid composites and improved their fluidity. Composites containing 2% of nano‐ZnO and 40% of GFs possessed the optimum mechanical properties. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Thermomechanical and barrier properties of UV‐cured epoxy/O‐montmorillonite nanocomposites

Mixtures of an epoxy resin and organophilic montmorillonites were subjected to ultraviolet (UV)‐induced photopolymerization. Two types of commercially available nanoclays, namely Cloisite 30B and Cloisite Na⁺, were modified through interaction with organic compatibilizers (dodecylsuccinic anhydride, octadecylamine, octadecyl alcohol, and octadecanoic acid). The modified nanoclays, dispersed in the liquid epoxy resin at 5 wt%, were photopolymerized to get nanocomposite films. The kinetics of the photopolymerization was evaluated by means of real‐time Fourier transform infrared spectroscopy. The modified nanoclays and their nanocomposites were characterized through X‐ray diffractometry; transmission electron microscopy showed the presence of intercalated and partially exfoliated morphologies in the nanocomposites. Thermogravimetric and dynamic‐mechanical analyses showed an increase of the thermal properties and an increase of the glass transition temperatures of the nanocomposites compared with that of the neat UV‐cured resin. Finally, the oxygen barrier properties of nanocomposite films, coated on a polyethyleneterephtalate substrate, were evaluated; the decrease of permeability was correlated with the degree of exfoliation of the nanocomposites. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Plasticization of nano‐CaCO3 in polystyrene/nano‐CaCO3 composites

The shear rheological properties of polystyrene (PS)/nano‐CaCO₃ composites were studied to determine the plasticization of nano‐CaCO₃ to PS. The composites were prepared by melt extrusion. A poly(styrene–butadiene–styrene) triblock copolymer (SBS), a poly(styrene–isoprene–styrene) triblock copolymer (SIS), SBS‐grafted maleic anhydride (SBS–MAH), and SIS‐grafted maleic anhydride were used as modifiers or compatibilizers. Because of the weak interaction between CaCO₃ and the PS matrix, the composites with 1 and 3 phr CaCO₃ loadings exhibited apparently higher melt shear rates under the same shear stress with respect to the matrix polymer. The storage moduli for the composites increased with low CaCO₃ concentrations. The results showed that CaCO₃ had some effects on the compatibility of PS/SBS (or SBS–MAH)/CaCO₃ composites, in which SBS could effectively retard the movement of PS chain segments. The improvement of compatibility, due to the chemical interaction between CaCO₃ and the grafted maleic anhydride, had obvious effects on the rheological behavior of the composites, the melt shear rate of the composites decreased greatly, and the results showed that nano‐CaCO₃ could plasticize the PS matrix to some extent. Rheological methods provided an indirect but useful characterization of the composite structure. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006