玻璃纤维增强煤基抗冲共聚聚丙烯的性能

采用双螺杆挤出共混法制备了短玻璃纤维(GF)改性聚丙烯(PP)2240S的共混物,通过力学性能分析测试、扫描电子显微镜表征、熔体流动速率测试和熔融结晶分析等研究了改性体系的力学性能、显微结构、加工流动性和结晶性能等。结果表明,当GF添加量为30%时,复合体系的弯曲强度、弯曲弹性模量、拉伸强度等较纯PP分别提高约112%,269%和108%,但GF与基体粘结力弱导致冲击强度没有提高;为进一步改善界面作用力,以5%马来酸酐接枝聚丙烯作相容剂,相同GF添加量下PP的弯曲强度达86.99 MPa,弯曲弹性模量达5073 MPa,拉伸强度达78.5 MPa,简支梁缺口冲击强度达14.78 kJ/m2,比纯PP的相关指标分别提高约161%,302%,190%和131%,GF与PP界面粘结力增强,PP的力学性能随GF含量的递增而大幅提高。但GF降低了PP的熔体流动速率,并且体系的结晶温度基本未变,结晶度降低,可能与未产生界面横晶有关。     

Properties enhancement of short glass fiber‐reinforced thermoplastics via sandwich injection molding

This article demonstrates using sandwich injection molding in order to improve the mechanical properties of short glass fiber‐reinforced thermoplastic parts by investigating the effect of fiber orientation, phase separation, and fiber attrition compared to conventional injection molding. In the present case, the effect of short glass fiber content (varying from 0–40 wt%) within the skin and core materials were studied. The results show that the mechanical properties strongly depend not only on the fiber concentration, but also on the fiber orientation and the fiber length distribution inside the injection‐molded part. Slight discrepancies in the findings can be assumed to be due to fiber breakage occurring during the mode of processing. POLYM. COMPOS., 26:823–831, 2005. © 2005 Society of Plastics Engineers     

注塑条件对长玻纤增强聚丙烯性能影响研究

利用熔融浸渍装置,采用长玻纤(LGF)增强双马来酰亚胺等改性的聚丙烯(PP),制备了LGF增强PP复合材料。研究了在螺杆转速为80～250 r/min、背压为8～10 MPa的注塑条件下,复合材料的纤维长度、力学性能与热变形温度的变化。在研究范围内,注塑工艺参数的变化对复合材料的弯曲强度和热变形温度没有明显的影响,但随着螺杆转速的提高,纤维长度下降,所得复合材料的冲击强度先降低后升高。     

玻纤增强聚丙烯木塑复合材料的性能研究

分别以聚丙烯(PP)、聚乙烯(PE)、玻纤增强PP/PE为基体材料,通过挤出成型制备了木塑复合材料(WPC)。研究表明,玻纤能够有效地提高WPC的性能,以玻纤增强PP/PE为基体制备的WPC的冲击强度、拉伸强度、弯曲强度、弯曲弹性模量分别达到4.58 kJ/m2,19 MPa,30.8 MPa,3520 MPa,性能优于以PP或PE为基体制备的WPC。     

Co‐injection molding of PVC with other thermoplastics: Processing,properties, and applications

Rigid poly(vinyl chloride) (PVC) was co‐injected with glass‐fiber‐reinforced PVC (GFR‐PVC), polypropylene (PP), acrylonitrile‐butadiene‐styrene copolymer (ABS), and polycarbonate (PC) by using the Mono‐sandwich co‐injection process. Up to three through‐thickness skin‐core morphologies were observed along the length of the sample. Near the gate, the core was always a single, continuous layer. In some cases, the core diverged into multiple or discontinuous layers. Farther from the gate, flow of the core ceased, leaving a skin‐only region. The skin and core layers were more uniformly distributed through the test plaque when injection speed was low. Adhesion between PVC and PP was poor. Skin and core layers delaminated, and mechanical properties were poor. The PVC adhered well to GFR‐PVC, ABS, and PC. No layer delamination occurred, and mechanical properties were intermediate between those of the skin and core components alone. Dropped dart impact energy was controlled more by the skin layer than the core. In rigid PVC/GFR‐PVC co‐injected samples, impact energy was 2.5 times greater when GFR‐PVC was the core than when GFR‐PVC was the skin.     

Influence of interfacial adhesion on the structural and mechanical behavior of PP‐banana/glass hybrid composites

Hybrid composites of polypropylene (PP), reinforced with short banana and glass fibers were fabricated using Haake torque rheocord followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both fibers into PP matrix resulted in increase of tensile strength, flexural strength, and impact strength upto 30 wt% with an optimum strength observed at 2 wt% MAPP treated 15 wt% banana and 15 wt% glass fiber. The rate of water absorption for the hybrid composites was decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has been analyzed to investigate the interfacial properties. An increase in storage modulus (E′) of the treated‐composite indicates higher stiffness. The loss tangent (tan δ) spectra confirms a strong influence of fiber loading and coupling agent concentration on the α and β relaxation process of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out through differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA), indicated an increase in the crystallization temperature and thermal stability of PP with the incorporation of MAPP‐treated banana and glass fiber. POLYM. COMPOS., 31:1247–1257, 2010. © 2009 Society of Plastics Engineers     

Banana/Glass Fiber-Reinforced Polypropylene Hybrid Composites: Fabrication and Performance Evaluation

Hybrid composites of Polypropylene (PP) reinforced with intimately mixed short banana and glass fibers were fabricated using Haake twin screw extruder followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both the fibers into PP matrix resulted in an increase in tensile, flexural and impact strength with an increasing level of fiber content upto 30 wt% at banana: glass fiber ratio of 15:15 wt% and 2 wt% of MAPP. The rate of water absorption for the hybrid composites decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has also been analyzed to investigate the interfacial properties. An increase in the storage modulus (E′) of the treated composite indicates higher stiffness. The tan δ spectra confirms a strong influence of fiber contents and coupling agent on the α and β relaxation processes of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out employing differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA) which indicated a decrease in the crystallization temperature and thermal stability of PP with the incorporation of MAPP treated banana and Glass fiber.     

Effect of macromolecular coupling agent on the property of PP/GF composites

Silane‐grafted polypropylene manufactured by a reactive grafting process was used as the coupling agent in polypropylene/glass‐fiber composites to improve the interaction of the interfacial regions. Polypropylene reinforced with 30% by weight of short glass fibers was injection‐molded and the mechanical behaviors were investigated. The results indicate that the mechanical properties (tensile strength, tensile modulus, flexural strength, flexural modulus, and Izod impact strength) of the composite increased remarkably as compared with the noncoupled glass fiber/polypropylene. SEM of the fracture surfaces of the coupled composites shows a good adhesion at the fiber/matrix interface: The fibers are coated with matrix polymer, and a matrix transition region exists near the fibers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1537–1542, 1999     

Preparation and mechanical properties of high‐performance short ramie fiber‐reinforced polypropylene composites

Short ramie fiber (RF) was used to reinforce the polypropylene (PP). The composites were prepared in a twin‐screw extruder followed by injection molding. The experimental results showed that both the strength and the modulus of the composites increase considerably with increasing RF content. The tensile strength and flexural strength are as high as 67 and 80 MPa by the incorporation of ramie up to 30 wt %. To the best of our knowledge, this is one of the best results for short natural fiber‐reinforced PP composites. However, the preparation method in this study is more simple and economic. This short RF‐reinforced PP composites extend the application field for short‐nature fiber‐reinforced PP composites. Morphological analysis revealed that it is the high aspect ratio of the fiber and good interfacial compatibility that result in the high performance of the composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

复配增容剂增容PPO/PP/GF研究

研究复配增容剂(SEPS/PP-g-MAH)对玻璃纤维(GF)增强聚苯醚(PPO)/聚丙烯(PP)力学性能、熔体流动性以及耐热性能的影响,并用扫描电子显微镜观察了不同共混体系的形态结构.结果表明,复配增容剂改善了PPO/PP/GF共混体系的相容性,提高了共混体系的拉伸强度、弯曲强度、冲击强度和熔体流动速率,但同时降低了...     

Effect of needle density on the mechanical properties of fiber-reinforced polypropylene composites

The partial impregnation textile preform consisting of chopped-strand, long glass fiber and nonwoven polypropylene (PP) has been prepared by needle-punching to improve fiber–matrix distribution before processing. These unconsolidated textile preforms were then preheated and hot-pressed for consolidation and formation. A multichannel recorder was used to determine the completion of impregnation on multilayer glass fiber-reinforced PP, which could significantly reduce the required consolidation time. The effect of needle density on their impregnation has studied by scanning electron microscopy and optical microscopy, along with mechanical analysis. The increasing needle density up to 400 st/cm² has increased the flexural modulus, but the impact strength decreased. The optimal needle density contained proper flexural and impact properties is 50–100 st/cm², consistent with the observations from scanning electron microscopy and optical microscopy. A similar phenomenon is also observed by using nonwoven maleic-anhydride-modified polypropylene (mPP) instead of unmodified PP. However, the effect of needle punching on flexural and impact properties is not significant in mPP, which is probably due to better adhesion between glass fiber and mPP matrix. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2169–2176, 1999     

Mechanical properties of injection molded long fiber polypropylene composites,Part 1: Tensile and flexural properties

Innovative polymers and composites are broadening the range of applications and commercial production of thermoplastics. Long fiber‐reinforced thermoplastics have received much attention due to their processability by conventional technologies. This study describes the development of long fiber reinforced polypropylene (LFPP) composites and the effect of fiber length and compatibilizer content on their mechanical properties. LFPP pellets of different sizes were prepared by extrusion process using a specially designed radial impregnation die and these pellets were injection molded to develop LFPP composites. Maleic‐anhydride grafted polypropylene (MA‐g‐PP) was chosen as a compatibilizer and its content was optimized by determining the interfacial properties through fiber pullout test. Critical fiber length was calculated using interfacial shear strength. Fiber length distributions were analyzed using profile projector and image analyzer software system. Fiber aspect ratio of more than 100 was achieved after injection molding. The results of the tensile and flexural properties of injection molded long glass fiber reinforced polypropylene with a glass fiber volume fraction of 0.18 are presented. It was found that the differences in pellet sizes improve the mechanical properties by 3–8%. Efforts are made to theoretically predict the tensile strength and modulus using the Kelly‐Tyson and Halpin‐Tsai model, respectively. POLYM. COMPOS., 28:259–266, 2007. © 2007 Society of Plastic Engineers     

粉末浸渍长玻璃纤维增强聚丙烯的注塑

采用粉末浸渍的方法制备连续玻璃纤维增强聚丙烯预浸料,经切割获得长纤维增强聚丙烯粒子,探索了材料的注塑工艺,研究了注塑后材料的力学性能及其影响因素。结果表明,粉末浸渍的长纤维增强聚丙烯经注塑后可获得力学性能的制品;随着预浸料切割长度的增长、纤维含量的增加,材料的力学性能提高;在基体聚丙烯中添加接枝极性基团的功能化聚丙烯,可改善体系的界面结合,提高材料的力学性能,但功能化聚丙烯的含量超过一定值后,材料的冲击强度有所下降;控制注塑时的模具温度,可以改变材料的一些力学性能。     

Mechanical,thermal and dynamic‐mechanical behavior of banana fiber reinforced polypropylene nanocomposites

Natural fiber‐reinforced nanocomposites based on polypropylene/nanoclay/banana fibers were fabricated by melt mixing in a twin‐screw extruder followed by compression molding in this current study. Maleic anhydride polypropylene copolymer (MA‐g‐PP) was used as a compatibilizer to increase the compatibility between the PP matrix, clay, and banana fiber to enhance exfoliation of organoclay and dispersion of fibers into the polymer matrix. Variation in mechanical, thermal, and physico‐mechanical properties with the addition of banana fiber into the PP nanocomposites was investigated. It was observed that 3 wt% of nanoclay and 5 wt% of MA‐g‐PP within PP matrix resulted in an increase in tensile and flexural strength by 41.3% and 45.6% as compared with virgin PP. Further, incorporation of 30 wt% banana fiber in PP nanocomposites system increases the tensile and flexural strength to the tune of 27.1% and 15.8%, respectively. The morphology of fiber reinforced PP nanocomposites has been examined by using scanning electron microscopy and transmission electron microscopy. Significant enhancement in the thermal stability of nanocomposites was also observed due to the presence of nanoclay under thermogravimetric analysis. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), conforming the strong interaction between nanoclay/banana fiberand MA‐g‐PP in the fiber‐reinforced nanocomposites systems. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Facilitating transcrystallization of polypropylene/glass fiber composites by imposed shear during injection molding

The transcrystal plays an important role in the enhancement of mechanical and thermal performances for polymer/glass fiber composites. Shear has been found to be a very effective way for the formation of transcrystal. Our purpose of this study was to explore the possibility to obtain the transcrystal in real processing such as injection molding. We will report our recent efforts on exploring the development of microstructure of polypropylene (PP)/glass fiber composite from skin to core in the injection-molded bars obtained by so-called dynamic packing injection molding which imposed oscillatory shear on the melt during solidification stage. A clear-cut shear-facilitated transcrystallization of PP on glass fibers was observed in the injection-molding bar for the first time. We suggested that shear could facilitate the transcrystalline growth through significantly improving the fiber orientation and the interfacial adhesion between fiber and matrix.     

Performance of long glass fiber‐reinforced polypropylene composites at different injection temperature

Long glass fiber‐reinforced polypropylene composites were prepared using self‐designed impregnation device. Effects of the different injection temperature on mechanical properties, crystallization, thermal, and dynamic mechanical properties of long glass fiber‐reinforced polypropylene composites were discussed. The differential scanning calorimetry (DSC) results indicate that the melting peak temperature of PP/LGF composites gradually reduced, however, the crystallinity of PP/LGF composites gradually increased with increasing injection temperature. Thermo‐gravimetric analyzer (TGA) results demonstrate that with increasing injection temperature, the temperature of the PP/LGF composites melt increased, the viscosity of the PP/LGF composites melt lowered, the mold filling of the PP/LGF composites melt was easy, the shear force of glass fiber was relatively low, which made the residual length of glass fiber in products increase. Dynamic thermal mechanical analyzer (DMA) results show that the storage modulus of PP/LGF composites is the highest while the injection temperature is at 290°C, and the peak value of tan σ of PP /LGF composites at 290°C is minimal, which indicates that the mechanical properties of PP /LGF composites at 290°C is the best. What' more, the injection temperature at 290°C significantly ameliorated “glass fiber rich skin” of products of glass fiber‐reinforced composites. J. VINYL ADDIT. TECHNOL., 24:233–238, 2018. © 2016 Society of Plastics Engineers     

Polypropylene–glass fiber/basalt fiber hybrid composites fabricated by direct fiber feeding injection molding process

Hybrid composites of polypropylene reinforced with glass fibers and basalt fibers were fabricated by vented injection molding machine which is named the direct fiber feeding injection molding (DFFIM) process. Polyamide 6 and maleic anhydride‐grafted polypropylene has been used as a coupling agent to improve the interfacial bonding between the fibers and matrix. Two types of vented injection molding machines with a different check ring and mold were used for making specimens. The fiber lengths were analyzed to identify the most suitable check ring and mold for the DFFIM process. The mechanical properties of the hybrid composites were investigated by tensile, flexural and Izod impact tests. The interfacial morphology of the fractured tensile specimens was studied by using scanning electron microscopy and showed that there is a fiber agglomeration phenomenon that occurs in the hybrid composites, and it has a significant effect on the mechanical properties of hybrid composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45472.     

连续玻纤增强聚丙烯混纤纱织物层压成型工艺研究

采用两种不同形式的混纤纱机织物为原料,利用层压成型的方法制备了连续玻璃纤维(GF)增强的聚丙烯(PP)板材。研究了层压温度、压力、保压时间和混纤纱机织物形式对层压板材的弯曲性能和层间剪切强度(ILSS)的影响。结果表明,当层压温度为230℃,层压压力为8.5 MPa,保压时间为30 min,降温过程冷却速度为0.5℃/min时,层压板材的力学性能最佳。弯曲强度和模量分别达到352.58 MPa、23.09 GPa,ILSS达到27.37 MPa。此时,纤维含量和空隙率分别为72.25%、2.03%。在最优工艺条件下制备的两种不同织物形式层压板材弯曲强度和弯曲模量以及ILSS:2/2斜纹织物平纹织物。两种织物层压板材的空隙率:2/2斜纹织物平纹织物。     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

长玻璃纤维增强热塑性塑料的开发应用

通过对玻璃纤维（GF）增强聚丙烯（PP）改性、长GF的表面浸润与分散性的研究,开发出与PP相容、充分适应长纤维增强热塑性塑料（LFT）加工要求的专用无捻粗纱,并通过长纤维造粒技术和注塑工艺制备性能优良的制品．其力学性能明显优于短GF增强PP。最后介绍了长GF增强热塑性塑料的应用前景。