Investigation of the performance and emissions of bus engine operating on butanol/diesel fuel blends

An experimental investigation is conducted to evaluate the effects of using blends of n-butanol (normal butanol) with conventional diesel fuel, with 8% and 16% (by vol.) n-butanol, on the performance and exhaust emissions of a fully instrumented, six-cylinder, water-cooled, turbocharged and after-cooled, heavy duty, direct injection (DI), Mercedes-Benz engine, installed at the authors’ laboratory, which is used to power the mini-bus diesel engines of the Athens Urban Transport Organization sub-fleet. The tests are conducted using each of the above fuel blends, with the engine working at two speeds and three loads. Fuel consumption, exhaust smokiness and exhaust regulated gas emissions such as nitrogen oxides, carbon monoxide and total unburned hydrocarbons are measured. The differences in the measured performance and exhaust emissions of the two butanol/diesel fuel blends from the baseline operation of the engine, i.e. when working with neat diesel fuel, are determined and compared. It is revealed that this fuel, which can be produced from biomass (bio-butanol), is a very promising bio-fuel for diesel engines. The differing physical and chemical properties of n-butanol against those for the diesel fuel, aided by sample cylinder pressure and heat release rate diagrams, are used to interpret the observed engine behavior.     

Emission characteristics using methyl soyate–ethanol–diesel fuel blends on a diesel engine

A blend of 20% (v/v) ethanol/methyl soyate was prepared and added to diesel fuel as an oxygenated additive at volume percent levels of 15 and 20% (denoted as BE15 and BE20). We also prepared a blend containing 20% methyl soyate in diesel fuel (denoted as B20). The fuel blends that did not have any other additive were stable for up to 3 months. Engine performance and emission characteristics of the three different fuels in a diesel engine were investigated and compared with the base diesel fuel. Observations showed that particulate matter (PM) emission decreased with increasing oxygenate content in the fuels but nitrogen oxides (NO_x) emissions increased. The diesel engine fueled by BE20 emitted significantly less PM and a lower Bosch smoke number but the highest NO_x among the fuel blends tested. All the oxygenate fuels produced moderately lower CO emissions relative to diesel fuel. The B20 blend emitted less total hydrocarbon (THC) emissions compared with base diesel fuel. This was opposite to the fuel blends containing ethanol (BE15, BE20), which produced much higher THC emission.     

Study of oxygenated biomass fuel blends on a diesel engine

Vegetable methyl ester was added in ethanol–diesel fuel to prevent separation of ethanol from diesel in this study. The ethanol blend proportion can be increased to 30% in volume by adding the vegetable methyl ester. Engine performance and emissions characteristics of the fuel blends were investigated on a diesel engine and compared with those of diesel fuel. Experimental results show that the torque of the engine is decreased by 6%–7% for every 10% (by volume) ethanol added to the diesel fuel without modification on the engine. Brake specific fuel consumption (BSFC) increases with the addition of oxygen from ethanol but equivalent brake specific fuel consumption (EBSFC) of oxygenated fuels is at the same level of that of diesel. Smoke and particulate matter (PM) emissions decrease significantly with the increase of oxygen content in the fuel. However, PM reduction is less significant than smoke reduction. In addition, PM components are affected by the oxygenated fuel. When blended fuels are used, nitrogen oxides (NO_x) emissions are almost the same as or slightly higher than the NO_x emissions when diesel fuel is used. Hydrocarbon (HC) is apparently decreased when the engine was fueled with ethanol–ester–diesel blends. Fuelling the engine with oxygenated diesel fuels showed increased carbon monoxide (CO) emissions at low and medium loads, but reduced CO emissions at high and full loads, when compared to pure diesel fuel.     

Combustion characteristics of waste-oil produced biodiesel/diesel fuel blends

In this study, wasted cooking oil from restaurants was used to produce neat (pure) biodiesel through transesterification, and this converted biodiesel was then used to prepare biodiesel/diesel blends. The goal of this study was to compare the trace formation from the exhaust tail gas of a diesel engine when operated using the different fuel type: neat biodiesel, biodiesel/diesel blends, and normal diesel fuels. B20 produced the lowest CO concentration for all engine speeds. B50 produced higher CO₂ than other fuels for all engine speeds, except at 2000 rpm where B20 gave the highest. The biodiesel and biodiesel/diesel blend fuels produced higher NO_x for various engine speeds as expected. SO₂ formation not only showed an increasing trend with increased engine speed but also showed an increasing trend as the percentage of diesel increased in the fuels. Among the collected data, the PM concentrations from B100 engines were higher than from other fuelled engines for the tested engine speed and most biodiesel-contained fuels produced higher PM than the pure diesel fuel did. Overall, we may conclude that B20 and B50 are the optimum fuel blends. The species of trace formation in the biodiesel-contained fuelled engine exhaust were mainly C_nH_2n+2, DEP, and DPS. For the B100, B80, B50, and D fuelled engines, C₁₅H₃₂ was the dominant species for all engine speeds, while squalene (C₃₀H₅₀) was the dominant for B20. DEP was only observed in the B100, B80, and B50 fuelled engines in this study. The D fuelled engine showed a higher DPS production for engine speeds higher than 1200 rpm.     

Biodiesel from safflower oil and its application in a diesel engine

Safflower seed oil was chemically treated by the transesterification reaction in methyl alcohol environment with sodium hydroxide (NaOH) to produce biodiesel. The produced biodiesel was blended with diesel fuel by 5% (B5), 20% (B20) and 50% (B50) volumetrically. Some of important physical and chemical fuel properties of blend fuels, pure biodiesel and diesel fuel were determined. Performance and emission tests were carried out on a single cylinder diesel engine to compare biodiesel blends with petroleum diesel fuel. Average performance reductions were found as 2.2%, 6.3% and 11.2% for B5, B20 and B50 fuels, respectively, in comparison to diesel fuel. These reductions are low and can be compensated by a slight increase in brake specific fuel consumption (Bsfc). For blends, Bsfcs were increased by 2.8%, 3.9% and 7.8% as average for B5, B20 and B50, respectively. Considerable reductions were recorded in PM and smoke emissions with the use of biodiesel. CO emissions also decreased for biodiesel blends while NO_x and HC emissions increased. But the increases in HC emissions can be neglected as they have very low amounts for all test fuels. It can be concluded that the use of safflower oil biodiesel has beneficial effects both in terms of emission reductions and alternative petroleum diesel fuel.     

Fuel production from waste vehicle tires by catalytic pyrolysis and its application in a diesel engine

An alternative fuel production was performed by pyrolysis of waste vehicle tires under nitrogen (N₂) environment and with calcium hydroxide (Ca(OH)₂) as catalyst. The sulfur content of liquids obtained were reduced by using Ca(OH)₂. The liquid fuel of waste vehicle tires(TF) was then used in a diesel engine to blend with petroleum diesel fuel by 5%(TF5), 10%(TF10), 15%(TF15), 25%(TF25), 35%(TF35), 50%(TF50), and 75%(TF75) wt. and pure (TF100). Performance characteristics such as engine power, engine torque, brake specific fuel consumption (bsfc) and exhaust temperature and emission parameters such as oxides of nitrogen (NOx), carbon monoxides (CO), total unburned hydrocarbon (HC), sulfur dioxides (SO₂) and smoke opacity of the engine operation with TF and blend fuels of TF-diesel were experimentally investigated and compared with those of petroleum diesel fuel. It was concluded that the blends of pyrolysis oil of waste tires TF5, TF10, TF25 and TF35 can efficiently be used in diesel engines without any engine modifications. However, the blends of TF50, TF75 and TF100 resulted considerably to high CO, HC, SO₂ and smoke emissions.     

Study on the application of DME/diesel blends in a diesel engine

In this paper fuels, based on various DME to diesel ratios are investigated. Physical and chemical properties of DME and diesel display mutual solubility at any ratio. The vapor pressure of DME/diesel blends is lower than that of pure DME at the same temperatures and it decreases with an increase of diesel mass fraction in blends, which is beneficial to the elimination of vapor lock in the fuel supply system on CI engines. Performance, emission and other features of three kinds of DME/diesel blend fuels and diesels are evaluated in a four-cylinder test engine. By taking relative advantages of DME and diesel, the DME/diesel blends could achieve satisfactory properties in lubricity and atomization, which contributed to improvements in spray and combustion characteristics. Simultaneously, smoke emission could be reduced significantly with a little penalty on CO and HC emissions for DME/diesel blended engine at high loads, in comparison to diesel engine. NO_x emissions of the engine powered by DME/diesel blends are decreased somewhat. Moreover, the power output would be improved a little and NO_x emission could be reduced further if the fuel supply advance angle is retarded appropriately.     

Experimental study of the effects of vegetable oil methyl ester on DI diesel engine performance characteristics and pollutant emissions

Vegetable oil methyl ester (VOME) is produced through the transesterification of vegetable oil and can be used as biodiesel in diesel engines as a renewable, nontoxic, and potentially environmentally friendly fossil fuel alternative in light of growing concerns regarding global warming and increasing oil prices. This study used VOME fuels produced from eight commonly seen oil bases to conduct a series of engine tests to investigate the effects of VOME on the engine performance, exhaust emissions, and combustion characteristics. The experimental results showed that using VOME in an unmodified direct injection (DI) diesel engine yielded a higher brake specific fuel consumption (BSFC) due to the VOME fuel’s lower calorific value. The high cetane number of VOME also imparted a better ignition quality and the high intrinsic oxygen content advanced the combustion process. The earlier start of combustion and the rapid combustion rate led to a drastic increase in the heat release rate (HRR) and the in-cylinder combustion pressure (ICCP) during the premixed combustion phase. A higher combustion rate resulted in higher peaks of HRR and ICCP as well as near the top dead center (TDC) position. Thus, it was found that a diesel engine fueled with VOME could potentially produce the same engine power as one fueled with petroleum diesel (PD), but with a reduction in the exhaust gas temperature (EGT), smoke and total hydrocarbon (THC) emissions, albeit with a slight increase in nitrogen oxides (NO_x) emissions. In addition, the VOME which possesses shorter carbon chains, more saturated bonds, and a higher oxygen content also yields a lower EGT as well as reduced smoke, NO_x, and THC emissions. However, this is obtained at the detriment of an increased BSFC.     

Engine performance and exhaust gas emissions of methanol and ethanol-diesel blends

In this study, the effects of methanol-diesel (M5, M10) and ethanol-diesel (E5, E10) fuel blends on the performance and exhaust emissions were experimentally investigated. For this work, a single cylinder, four-stroke, direct injection, naturally aspirated diesel engine was used. The tests were performed by varying the engine speed between 1000 and 1800 rpm while keeping the engine torque at 30 Nm. The results showed that brake specific fuel consumption and emissions of nitrogen oxides increased while brake thermal efficiency, smoke opacity, emissions of carbon monoxide and total hydrocarbon decreased with methanol-diesel and ethanol-diesel fuel blends.     

Performance and emission characteristics of an CI engine fueled with diesel–biodiesel–bioethanol blends

The paper presents the experimental results obtained concerning performances and pollution of a diesel engine fueled with diesel–biodiesel–ethanol blends compared with diesel fuel in laboratory tests. The main properties of the researched fuels are presented within this paper, in comparison with classical diesel fuel (chemical composition, density, kinematic viscosity, cold filter plugging point, flash point). Engines’ performances were evaluated by determining the brake specific fuel consumption and brake thermal efficiency. For pollution evaluation the emissions of CO, CO₂, NO_x, HC and smoke have been measured. An increasing of brake specific fuel consumption has been observed, especially at lower engines’ loads, with maximum 32.4%, reducing engine brake thermal efficiency with maximum 21.7%. CO emissions decrease, especially at high loads with maximum 59%, on the basis of CO₂ increased emissions. NO_x emissions slightly increase, especially at partial and high loads, meanwhile HC and smoke emissions decrease in all engines’ load cycles.     

Effect of dimethoxy-methane and exhaust gas recirculation on combustion and emission characteristics of a direct injection diesel engine

The effect of fuel constituents and exhaust gas recirculation (EGR) on combustion characteristics, fuel efficiency and emissions of a direct injection diesel engine fueled with diesel-dimethoxymethane (DMM) blends was investigated experimentally. Three diesel-DMM blended fuels containing 20%, 30% and 50% by volume fraction of DMM, corresponding to 8.5%, 12.7% and 21.1% by mass of oxygen in the blends, were used. By the use of DMM, it is observed that CO and smoke emissions as well as the total number and mass concentration of particulate reduce significantly, while HC emissions and particulate number with lower geometric mean diameters (D_i < 0.039 μm) increase slightly. For each fuel, there is an increase of ignition delay whereas a decrease of cylinder pressure and heat release rate in the premixed combustion phase when the diesel engine was operated with EGR system. The brake thermal efficiency fluctuates at small EGR ratio, while decreases with the further increase of EGR ratio. With an increase of EGR ratio, NO_x emission is reduced at the cost of increased smoke, HC and CO emissions as well as the total number and mass of particulates for each fuel.     

Performance of compression ignition engine with mahua (Madhuca indica) biodiesel

The performance of biodiesel obtained from mahua oil and its blend with high speed diesel in a Ricardo E6 engine has been presented in this paper together with some of its fuel properties. These properties were found to be comparable to diesel and confirming to both the American and European standards. Engine performance (brake specific fuel consumption, brake thermal efficiency and exhaust gas temperature) and emissions (CO, smoke density and NO_x) were measured to evaluate and compute the behaviour of the diesel engine running on biodiesel. The reductions in exhaust emissions and brake specific fuel consumption together with increase brake power, brake thermal efficiency made the blend of biodiesel (B20) a suitable alternative fuel for diesel and thus could help in controlling air pollution.     

The influence of operating parameters on the performance and emissions of a DI diesel engine using methanol-blended-diesel fuel

In this study, the effects of injection pressure and timing on the performance and emission characteristics of a DI diesel engine using methanol (5%, 10% and 15%) blended-diesel fuel were investigated. The tests were conducted on three different injection pressures (180, 200 and 220 bar) and timings (15°, 20°, and 25° CA BTDC) at 20 Nm engine load and 2200 rpm. The results indicated that brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC), and nitrogen oxides (NO_x) emissions increased as brake thermal efficiency (BTE), smoke opacity, carbon monoxide (CO) and total unburned hydrocarbon (THC) decreased with increasing amount of methanol in the fuel mixture. The best results were achieved for BSFC, BSEC and BTE at the original injection pressure and timing. For the all test fuels, the increasing injection pressure and timing caused to decrease in the smoke opacity, CO, THC emissions while NO_x emissions increase.     

Experimental investigation of diesel engine performance and emission characteristics using jojoba/diesel blend and sunflower oil

Experimental study has been carried out to investigate performance parameters, emissions, cylinder pressure, exhaust gas temperature (T_exhaust) and engine wall temperatures (T_wall) for direct injection diesel engine. Tests were conducted for sunflower oil (S100) and 20% jojoba oil + 80% pure diesel fuel (B20) in comparison to pure diesel fuel with different engine speeds. S100 and B20 were selected for the study because of its being widely used in Egypt and in the world. Also, series of tests are conducted at same previous conditions with different percentage of exhaust gas recirculation (EGR) from 0% to 12% of inlet mass of air fresh charge. Results indicate that S100 or B20 gives lower brake thermal efficiency (η_B), brake power (BP), brake mean effective pressure (BMEP), and higher brake specific fuel consumption (BSFC) due to lower heating value compared to pure diesel fuel. S100 or B20 gives lower NO_X concentration due to lower gas temperature. S100 or B20 gives higher T_wall and T_exhaust due to incomplete combustion inside engine cylinder. S100 or B20 gives higher CO and CO₂ concentrations due to higher carbon/hydrogen ratio. The position of maximum pressure (P_max) change for pure diesel fuel is earlier than for S100 or B20. The results show that S100 or B20 are promising as alternative fuel for diesel engine. The utilization of vegetable oils does not require a significant modification of existing engines. This can be seen as the main advantage of vegetable oils. The main disadvantages of biodiesel fuels are high viscosity, drying with time, thickening in cold conditions, flow and atomization characteristics.     

Effects of ethyl tert-butyl ether addition to diesel fuel on characteristics of combustion and exhaust emissions of diesel engines

The effects of ethyl tert-butyl ether (ETBE) addition to diesel fuel on the characteristics of combustion and exhaust emissions of a common rail direct injection diesel engine with high rates of cooled exhaust gas recirculation (EGR) were investigated. Test fuels were prepared by blending 0, 10, 20, 30 and 40 vol% ETBE to a commercial diesel fuel. Increasing ETBE fraction in the fuel helps to suppress the smoke emission increasing with EGR, but a too high fraction of ETBE leads to misfiring at higher EGR rates. While the combustion noise and NO_x emissions increase with increases in ETBE fraction at relatively low EGR rates, they can be suppressed to low levels by increasing EGR. Though there are no significant increases in THC and CO emissions due to ETBE addition to diesel fuel in a wide range of EGR rates, the ETBE blended fuel results in higher aldehyde emissions than the pure diesel fuel at relatively low EGR rates. With the 30% ETBE blended fuel, the operating load range of smokeless, ultra-low NO_x (<0.5 g/kWi h), and efficient diesel combustion with high rates of cooled EGR is extended to higher loads than with the pure diesel fuel.     

Performance and emission study of waste anchovy fish biodiesel in a diesel engine

Waste anchovy fish oils transesterification was studied with the purpose of achieving the conditions for biodiesel usage in a single cylinder, direct injection compression ignition. With this purpose, the pure biodiesel produced from anchovy fish oil, biodiesel-diesel fuel blends of 25%:75% biodiesel-diesel (B25), 50%:50% biodiesel-diesel (B50), 75%:25% biodiesel-diesel (B75) and petroleum diesel fuels were used in the engine to specify how the engine performance and exhaust emission parameters changed. The fuel properties of test fuels were analyzed. Tests were performed at full load engine operation with variable speeds of 1000, 1500, 2000 and 2500 rpm engine speeds. As results of investigations on comparison of fuels with each other, there has been a decrease with 4.14% in fish oil methyl ester (FOME) and its blends' engine torque, averagely 5.16% reduction in engine power, while 4.96% increase in specific fuel consumption have been observed. On one hand there has been average reduction as 4.576%, 21.3%, 33.42% in CO₂, CO, HC, respectively; on the other hand, there has been increase as 9.63%, 29.37% and 7.54% in O₂, NO_x and exhaust gas temperature has been observed. It was also found that biodiesel from anchovy fish oil contains 37.93 wt.% saturated fatty acids which helps to improve cetane number and lower NO_x emissions. Besides, for biodiesel and its blends, average smoke opacity was reduces about 16% in comparison to D2. It can be concluded that waste anchovy fish obtained from biodiesel can be used as a substitute for petroleum diesel in diesel engines.     

Regulated and unregulated emissions from a light-duty diesel engine with different sulfur content fuels

Five different sulfur content fuels were used on a light-duty diesel engine to study the effect of fuel sulfur on emissions. Four regulated emissions: smoke, nitrogen oxide (NO_x), unburned hydrocarbon (HC) and carbon monoxide (CO) emissions of the engine were investigated, as well as three unregulated emissions: formaldehyde (HCHO), acetaldehyde (MECHO) and sulfur dioxide (SO₂). The smoke emission decreases continuously and remarkably with the fuel sulfur content, and the fuel sulfur has more influence on smoke emission at lower engine load. The concentration of NO_x emissions did not change significantly with the different sulfur content fuels. As the fuel sulfur content decreases, the concentrations of HC and CO emissions have distinct reduction. The HCHO emission values are very low. The MECHO emission decreases with increasing engine load, and it continuously decreases with the fuel sulfur content and it could not be detected at higher engine load with 50 ppm sulfur fuel. The SO₂ emission increases continuously with the engine load, and obviously decreases with the fuel sulfur contents.     

Feasibility of blending karanja vegetable oil in petro-diesel and utilization in a direct injection diesel engine

Karanja (Pongamia pinnata) oil, a non-edible high viscosity (27.84 cSt at 40 °C) straight vegetable oil, was blended with conventional diesel in various proportions to evaluate the performance and emission characteristics of a single cylinder direct injection constant speed diesel engine. Diesel and karanja oil fuel blends (5%, 10%, 15%, and 20%) were used to conduct short-term engine performance and emission tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over the entire range of engine operation and engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature, and exhaust emissions (smoke, CO, CO₂, HC, NO_x, and O₂) were recorded. The brake specific energy consumption (BSEC), brake thermal efficiency (BTE), and exhaust emissions were evaluated to determine the optimum fuel blend. Higher BSEC was observed at full load for neat petro-diesel. A fuel blend of 10% karanja oil (KVO10) showed higher BTE at a 60% load. Similarly, the overall emission characteristics were found to be best for the case of KVO10 over the entire range of engine operation.     

Combustion and emissions of a DI diesel engine fuelled with diesel-oxygenate blends

Combustion and emissions of a DI diesel engine fuelled with diesel-oxygenate blends were investigated. The results show that there exist the different behaviors in the combustion between the diesel-diglyme blends and the other five diesel-oxygenate blends as the diglyme has the higher cetane number than that of diesel fuel while the other five oxygenates have the lower cetane number than that of diesel fuel. The smoke concentration decreases regardless of the types of oxygenate additives, and the smoke decreases with the increase of the oxygen mass fraction in the blends without increasing the NO_x and engine thermal efficiency. The reduction of smoke is strongly related to the oxygen-content of blends. CO and HC concentrations decrease with the increase of oxygen mass fraction in the blends. Unlike conventional diesel engines fueled with pure diesel fuel, engine operating on the diesel-oxygenate blends presents a flat NO_x/Smoke tradeoff curve versus oxygen mass fraction.     

Experimental study on performance and emissions of a high speed diesel engine fuelled with n-butanol diesel blends under premixed low temperature combustion

In the present paper, results of an experimental investigation carried out in a modern diesel engine running at different operative conditions and fuelled with blends of diesel and n-butanol, are reported. The exploration strategy was focused on the management of the timing and injection pressure to achieve a condition in which the whole amount of fuel was delivered before ignition. The aim of the paper was to evaluate the potential to employ fuel blends having low cetane number and high resistance to auto-ignition to reduce engine out emissions of NOx and smoke without significant penalty on engine performance. Fuel blends were mixed by the baseline diesel (BU00) with 20% and 40% of n-butanol by volume. The n-butanol was taken by commercial production that is largely produced through petrochemical pathways although the molecule is substantially unchanged for butanol produced through biological mechanisms.The experimental activity was performed on a turbocharged, water cooled, DI diesel engine, equipped with a common rail injection system. The engine equipment includes an exhaust gas recirculation system controlled by an external driver, a piezo-quartz pressure transducer to detect the in-cylinder pressure signal and a current probe to acquire the energizing current to the injectors. Engine tests were carried out at 2500 rpm and 0.8 MPa of BMEP exploring the effect of start of injection, O₂ concentration at intake and injection pressure on combustion behavior and engine out emissions. The in-cylinder pressure and rate of heat release were investigated for the neat diesel and the two blends to evaluate engine performance and exhaust emissions both for the conventional diesel and the advanced premixed combustion processes.The management of injection pressure, O₂ concentration at intake and injection timing allowed to realize a partial premixed combustion by extending the ignition delay, particularly for blends. The main results of the investigation made reach smoke and NOx emissions due to the longer ignition delay and a better mixing control before combustion. The joint effect of higher resistance to auto ignition and higher volatility of n-butanol blends improved emissions compared to the neat diesel fuel with a low penalty on fuel consumption.