A capacitor-free CMOS LDO regulator with AC-boosting and active-feedback frequency compensation

A capacitor-free CMOS low-dropout(LDO)regulator for system-on-chip(SoC)applications is presented.By adopting AC-boosting and active-feedback frequency compensation(ACB-AFFC),the proposed LDO enhancement circuit is adopted to increase the slew rate and decrease the output voltage dips when the load current is suddenly switched from low to high.The LDO regulator is designed and fabricated in a 0.6/am CMOS process.The active silicon area is only 770×472μm2.Experimental results show that the total error of the output voltage due to line variation is less than ±0.1 97%.The load regulation is only 0.35 mV/mA when the load current changes fromoto 100mA.     

CMOS low dropout linear regulator with single Miller capacitor

A 2-5V 150 mA CMOS low dropout (LDO) linear regulator with a single Miller capacitor of 4pF is presented. The proposed LDO regulator with a bandgap voltage reference has been fabricated in a 0.35 /spl mu/m CMOS process and the active chip area is 485/spl times/586 /spl mu/m. The maximum output current is 150 mA and the regulated output voltage is 1.8 V.     

A CMOS voltage reference based on weighted /spl Delta/V/sub GS/ for CMOS low-dropout linear regulators

A CMOS voltage reference, which is based on the weighted difference of the gate-source voltages of an NMOST and a PMOST operating in saturation region, is presented. The voltage reference is designed for CMOS low-dropout linear regulators and has been implemented in a standard 0.6-/spl mu/m CMOS technology (V/sub thn//spl ap/|V/sub thp/|/spl ap/0.9 V at 0/spl deg/C). The occupied chip area is 0.055 mm/sup 2/. The minimum supply voltage is 1.4 V, and the maximum supply current is 9.7 /spl mu/A. A typical mean uncalibrated temperature coefficient of 36.9 ppm//spl deg/C is achieved, and the typical mean line regulation is /spl plusmn/0.083%/V. The power-supply rejection ratio without any filtering capacitor at 100 Hz and 10 MHz are -47 and -20 dB, respectively. Moreover, the measured noise density with a 100-nF filtering capacitor at 100 Hz is 152 nV//spl radic/(Hz) and that at 100 kHz is 1.6 nV//spl radic/(Hz).     

A frequency compensation scheme for LDO voltage regulators

A stable low dropout (LDO) voltage regulator topology for low equivalent series resistance (ESR) capacitive loads is presented. The proposed scheme generates a zero internally instead of relying on the zero generated by the load capacitor and its ESR combination for stability. It is demonstrated that this scheme realizes robust frequency compensation, facilitates the use of multilayer ceramic capacitors for the load of LDO regulators, and improves transient response and noise performance. Test results from a prototype fabricated in AMI 0.5-/spl mu/m CMOS technology provide the most important parameters of the regulator viz., ground current, load regulation, line regulation, output noise, and start-up time.     

一种快速瞬态响应的无片外电容LDO的设计

基于上华0.5μm工艺,设计了输入电压范围为3.5～6.5V,输出电压为3.3V,最大输出电流为100mA的CMOS无片外电容的低压差线性稳压器.提出了一种自动检测网络用来快速感应负载电流的变化,抑制输出电压的跳变,改善了负载瞬态响应.在稳定性方面,采用miller补偿,加之第二级采用了输出电阻很小的buffer结构[1],这样主极点和次极点分离很远使得系统稳定.仿真表明,该LDO在VIN=6.5V和VIN=3.5V下under-shoot分别为156mV和135mV,overshoot分别为145mV和60mV,线性调整率和负载调整率分别为0.023%和0.5%.     

Design of a low-power 3.5-GHz broad-band CMOS transimpedance amplifier for optical transceivers

This paper describes a novel low-power low-noise CMOS voltage-current feedback transimpedance amplifier design using a low-cost Agilent 0.5-/spl mu/m 3M1P CMOS process technology. Theoretical foundations for this transimpedance amplifier by way of gain, bandwidth and noise analysis are developed. The bandwidth of the amplifier was extended using the inductive peaking technique, and, simulation results indicated a -3-dB bandwidth of 3.5 GHz with a transimpedance gain of /spl ap/60 dBohms. The dynamic range of the amplifier was wide enough to enable an output peak-to-peak voltage swing of around 400 mV for a test input current swing of 100 /spl mu/A. The output noise voltage spectral density was 12 nV//spl radic/Hz (with a peak of /spl ap/25 nV//spl radic/Hz), while the input-referred noise current spectral density was below 20 pA//spl radic/Hz within the amplifier frequency band. The amplifier consumes only around 5 mA from a 3.3-V power supply. A test chip implementing the transimpedance amplifier was also fabricated using the low-cost CMOS process.     

A fully on-chip 1-μW capacitor-free low-dropout regulator with adaptive output stage

A fully on-chip 1-μW fast-transient response capacitor-free low-dropout regulator (LDO) using adaptive output stage (AOS) is presented in this paper in standard 0.13-μm CMOS process. The AOS circuit is proposed to deliver extra four times of output current of the operational amplifier at medium to heavy load to extend the bandwidth of the LDO and enhance the slew rate at the gate of the power transistor. And the AOS circuit is shut off at light load to reduce the quiescent current and maintain the stability without requiring area-consuming on-chip capacitor. Meanwhile, the proposed AOS circuit introduces V_OUT offset at medium to heavy load to counteract the V_OUT drop, which is caused by I_LOAD increase. Hence, transient performances of LDO and V_OUT drop between light load and full load are improved significantly with 1.1-μA quiescent current at light load. From the post simulation results, the LDO regulates the output voltage at 0.7 V from a 0.9-V supply voltage with a 100-mA maximum load current. The undershoot, the overshoot and the recovery time of the proposed LDO with I_LOAD switching from 50 μA to 100 mA in 1 μs are about 130 mV, 130 mV and 1.5 μs, respectively. And the V_OUT drop between light load and full load reduces to 0.16 mV.     

CMOS voltage references using lateral bipolar transistors

Two bandgap references are presented which make use of CMOS compatible lateral bipolar transistors. The circuits are designed to be insensitive to the low beta and alpha current gains of these devices. Their accuracy is not degraded by any amplifier offset. The first reference has an intrinsic low output impedance. Experimental results yield an output voltage which is constant within 2 mV, over the commercial temperature range (0 to 70/spl deg/C), when all the circuits of the same batch are trimmed at a single temperature. The load regulation is 3.5 /spl mu/V//spl mu/A, and the power supply rejection ratio (PSRR) at 100 Hz is 60 dB. Measurements on a second reference yield a PSRR of minimum 77 dB at 100 Hz. Temperature behaviour is identical to the first circuit presented. This circuit requires a supply voltage of only 1.7 V.     

A low-voltage 40-GHz complementary VCO with 15% frequency tuning range in SOI CMOS technology

The design of a low-voltage 40-GHz complementary voltage-controlled oscillator (VCO) with 15% frequency tuning range fabricated in 0.13-/spl mu/m partially depleted silicon-on-insulator (SOI) CMOS technology is reported. Technological advantages of SOI over bulk CMOS are demonstrated, and the accumulation MOS (AMOS) varactor limitations on frequency tuning range are addressed. At 1.5-V supply, the VCO core and each output buffer consumes 11.25 mW and 3 mW of power, respectively. The measured phase noise at 40-GHz is -109.73 dBc/Hz at 4-MHz offset from the carrier, and the output power is -8 dBm. VCO performance using high resistivity substrate (/spl sim/300-/spl Omega//spl middot/cm) has the same frequency tuning range but 2 dB better phase noise compared with using low resistivity substrate (10 /spl Omega//spl middot/cm). The VCO occupies a chip area of only 100 /spl mu/m by 100 /spl mu/m (excluding pads).     

A full on-chip CMOS low-dropout voltage regulator with VCCS compensation

A full on-chip CMOS low-dropout(LDO) voltage regulator with high PSR is presented.Instead of relying on the zero generated by the load capacitor and its equivalent series resistance,the proposed LDO generates a zero by voltage-controlled current sources for stability.The compensating capacitor for the proposed scheme is only 0.18 pF,which is much smaller than the capacitor of the conventional compensation scheme.The full on-chip LDO was fabricated in commercial 0.35μm CMOS technology.The active chip area...     

交流提升与有源反馈补偿的无片外电容CMOS低压差稳压器

A capacitor-free CMOS low-dropout （LDO） regulator for system-on-chip （SoC） applications is presented. By adopting AC-boosting and active-feedback frequency compensation （ACB-AFFC）, the proposed LDO regulator, which is independent of an off-chip capacitor, provides high closed-loop stability. Moreover, a slew rate enhancement circuit is adopted to increase the slew rate and decrease the output voltage dips when the load current is suddenly switched from low to high. The LDO regulator is designed and fabricated in a 0.6 μm CMOS process. The active silicon area is only 770 × 472 μm2. Experimental results show that the total error of the output voltage due to line variation is less than ±0.197%. The load regulation is only 0.35 mV/mA when the load current changes from 0 to 100 mA.     

192 GHz push-push VCO in 0.13 /spl mu/m CMOS

A 192 GHz cross-coupled push-push voltage controlled oscillator (VCO) is fabricated using the UMC 0.13 /spl mu/m CMOS logic process. The VCO can be tuned from 191.4 to 192.7 GHz. The VCO provides output power of /spl sim/-20 dBm and phase noise of /spl sim/-100 dBc/Hz at 10 MHz offset, while consuming 11 mA from a 1.5 V supply.     

Piezoelectric micro-power generation interface circuits

New power conversion circuits to interface to a piezoelectric micro-power generator have been fabricated and tested. Circuit designs and measurement results are presented for a half-wave synchronous rectifier with voltage doubler, a full-wave synchronous rectifier and a passive full-wave rectifier circuit connected to the piezoelectric micro-power generator. The measured power efficiency of the synchronous rectifier and voltage doubler circuit fabricated in a 0.35-/spl mu/m CMOS process is 88% and the output power exceeds 2.5 /spl mu/W with a 100-k/spl Omega/, 100-nF load. The two full-wave rectifiers (passive and synchronous) were fabricated in a 0.25-/spl mu/m CMOS process. The measured peak power efficiency for the passive full-wave rectifier circuit is 66% with a 220-k/spl Omega/ load and supplies a peak output power of 16 /spl mu/W with a 68-k/spl Omega/ load. Although the active full-wave synchronous rectifier requires quiescent current for operation, it has a higher peak efficiency of 86% with an 82-k/spl Omega/ load, and also exhibits a higher peak power of 22 /spl mu/W with a 68-k/spl Omega/ load which is 37% higher than the passive full-wave rectifier.     

A dual-path bandwidth extension amplifier topology with dual-loop parallel compensation

A dual-path amplifier topology with dual-loop parallel compensation technique is proposed for low-power three-stage amplifiers. By using two parallel high-speed paths for high-frequency signal propagation, there is no passive capacitive feedback network loaded at the amplifier output. Both the bandwidth and slew rate are thus significantly improved. Implemented in a 0.6-/spl mu/m CMOS process, the proposed three-stage amplifier has over 100-dB gain, 7-MHz gain-bandwidth product, and 3.3-V//spl mu/s average slew rate while only dissipating 330 /spl mu/W at 1.5 V, when driving a 25-k/spl Omega///120-pF load. The proposed amplifier achieves at least two times improvement in bandwidth-to-power and slew-rate-to-power efficiencies than all other reported multistage amplifiers using different compensation topologies.     

A quad CMOS single-supply op amp with rail-to-rail output swing

The realization of a commercially viable, general-purpose quad CMOS amplifier is presented, along with discussions of the tradeoffs involved in such a design. The amplifier features an output swing that extends to either supply rail, together with an input common-mode range that includes ground. The device is especially well suited for single-supply operation and is fully specified for operation from 5 to 15 V over a temperature range of -55 to +125/spl deg/C. In the areas of input offset voltage, offset voltage drift, input noise voltage, voltage gain, and load driving capability, this implementation offers performance that equals or exceeds that of popular general-purpose quads or bipolar of Bi-FET construction. On a 5-V supply the typical V/SUB os/ is 1 Mv, V/SUB os/ drift is 1.3 /spl mu/V//spl deg/C, 1-kHz noise is 36 nV//spl radic/Hz, and gain is one million into a 600-/spl Omega/ load. This device achieves its performance through circuit design and layout techniques as opposed to special analog CMOS processing, thus lending itself to use on system chips built with digital CMOS technology.     

基于高摆率误差放大器的无片外电容LDO设计

为了解决无片外电容低压差线性稳压器(LDO)的瞬态响应性能较差的问题,采用跨导提高技术设计了一种高摆率的误差放大器.在误差放大器的基础上,通过电容将LDO的输出端耦合至电流镜构建瞬态增强电路,提升LDO的瞬态响应能力,且瞬态增强电路可以引入两个左半平面零点,改善环路的稳定性.同时,误差放大器采用动态偏置结构,进一步减小...     

一种动态补偿、高稳定性的LDO设计

设计并实现了一种动态补偿、高稳定性的LDO.针对LDO控制环路稳定性随负载电流变化的特点,给出一种新颖的动态补偿电路.这种补偿电路能很好地跟踪负载电流的变化,从而使控制环路的稳定性几乎与负载电流无关.设计采用CSMC 0.5μm标准CMOS工艺,利用Cadence的EDA工具完成电路设计、版图绘制和流片测试,最终芯片面...     

50 Gbit/s 2:1 multiplexer in 0.13 /spl mu/m CMOS technology

A fully integrated 2:1 multiplexer IC which operates at up to 50 Gbit/s data rate is presented. The MUX uses inductive shunt peaking and an output series inductor for higher bandwidth. The MUX directly drives the 50 /spl Omega/ load. The IC is fabricated in a 0.13 /spl mu/m bulk CMOS technology and draws 65 mA at 1.5 V supply voltage. The output voltage swing is 2/spl times/100 mV.     

A low phase-noise CMOS VCO with harmonic tuned LC tank

This paper presents a phase-noise reduction technique for voltage-controlled oscillators (VCOs) using a harmonic tuned (HT) LC tank. The phase-noise suppression is achieved through almost rectangular-shaped voltage at the switching differential cell, which effectively maximizes the slope of the switching cell output voltage at a zero crossing point. In addition, the proposed technique also suppresses the down-conversion of the noise around the second harmonic frequency by the second harmonic short of the tank. One second HT VCO and two third HT VCOs are designed and implemented to evaluate the concept using a 0.35- and 0.13-/spl mu/m CMOS process. The figure-of-merit (FOM) of the second HT VCO, third HT VCO1, and third HT VCO2 are -180.7, -183.7, and -189.5, respectively. The best FOM performance of the VCO has phase noises of -100.4, -132.0, and -140.8dBc/Hz at 100-kHz, 1-MHz, and 3-MHz offset frequencies at the 2-GHz carrier, respectively. This VCO consumes 3.29 mA from a 1.8-V supply with the silicon area of 500 /spl mu/m/spl times/750 /spl mu/m.     

A 1.76-GHz 22.6-mW /spl Delta//spl Sigma/ fractional-n frequency synthesizer

A /spl Delta//spl Sigma/ fractional-N frequency synthesizer for the 2-GHz-range wireless communication applications is implemented in a 0.35-/spl mu/m BiCMOS process, using only CMOS components. The synthesizer achieves a close-in phase noise of -81 dBc/Hz, while the spurious tones are at -85 dBc. The synthesizer features a multiple-modulus prescaler employing the phase-switching architecture to minimize the power dissipation. The entire prescaler, including the gigahertz-speed first stages, is implemented using full-swing logic. The current source structure employed in the charge pump provides a constant output current over a wide, almost rail-to-rail output voltage range. The power dissipation of the synthesizer chip is 22.6 mW from a 2.7-V supply.