Crystal structure,thermal behaviour,vibrational spectroscopy and optical properties of new compounds K$$_{}$$Ca(HAsO$$_{4}$$4)$$_{}\cdot $$·H$$_{}$$O with kröhnkite-type chain

The new kröhnkite compound called potassium calcium-bis-hydrogen arsenate dihydrate K\(_{2}\)Ca(HAsO\(_{4})_{2}\cdot \)2H\(_{2}\)O was obtained by hydrothermal method and characterized by X-ray diffraction, infrared spectroscopy, Raman scattering, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis and optical (photoluminescence and absorption) properties. It crystallizes in the triclinic space group P\(\bar{1}\) and unit cell parameters \(a = 5.971(3)\) Å, \(b =6.634(3)\) Å, \(c = 7.856(4)\) Å, \(\alpha =104.532(9)\) \(^{\circ }\), \(\beta = 105.464(9)\) \(^{\circ }\) and \(\gamma = 109.698(9)\) \(^{\circ }\). The structure of K\(_{2}\)Ca(HAsO\(_{4})_{2}\cdot \)2H\(_{2}\)O built up from this infinite, (Ca(HAsO\(_{4})_{2}\)(H\(_{2}\)O)\(_{2})^{2+}\), was oriented along an axis resulting from the association of CaO\(_{6}\) octahedra alternating with each two HAsO\(_{4}\) tetrahedra by sharing corners. Each potassium atom links two adjacent chains by three oxygen atoms of HAsO\(_{4}\) tetrahedra. TGA and DSC have shown the absence of phase transition. The existence of vibrational modes corresponding to the kröhnkite is identified by the IR and Raman spectroscopies in the frequency ranges of 400–4000 and 20–4000 cm\(^{-1}\), respectively. The photoluminescence measurement show one peak at 507 nm, which is attributed to band–band (free electron–hole transitions) and (bound electron–hole transitions) emissions within the AsO\(_{4}\) inorganic part.     

Structural,dielectric and piezoelectric study of Ca-, Zr-modified $$\hbox {BaTiO}_{3}$$ lead-free ceramics

We prepared a lead-free ceramic (\(\hbox {Ba}_{0.85}\hbox {Ca}_{0.15})(\hbox {Ti}_{1-x}\hbox {Zr}_{x})\hbox {O}_{3}\) (BCTZ) using the conventional mixed oxide technique. The samples were prepared by an ordinary mixing and sintering technique. In this study we investigated how small amounts of \(\hbox {Zr}^{4+}\) can affect the crystal structure and microstructure as well as dielectric and piezoelectric properties of \(\hbox {BaTiO}_{3}\). X-ray diffraction analysis results indicate that no secondary phase is formed in any of the BCTZ powders for \(0 \le x \le 0.1\), suggesting that \(\hbox {Zr}^{4+}\) diffuses into \(\hbox {BaTiO}_{3}\) lattices to form a solid solution. Scanning electron microscopy micrographs revealed that the average grain size gradually increased with \(\hbox {Zr}^{4+}\) content from 9.5 \(\upmu \!\hbox {m}\) for \(x = 0.02\) to 13.5 \(\upmu \!\hbox {m}\) for \(x = 0.1\); Curie temperature decreased due to the small tetragonality caused by \(\hbox {Zr}^{4+}\) addition. Owing to the polymorphic phase transition from orthorhombic to tetragonal phase around room temperature, it was found that the composition \(x = 0.09\) showed improved electrical properties and reached preferred values of \(d_{33} = 148\) pC \(\hbox {N}^{-1}\) and \(K_{\mathrm{p}} = 27\%\).     

Study of Lanthanide Complexes with BTFA in Silica Gels by Photoacoustic Spectroscopy

In this work, lanthanide \(\beta \)-diketonate complexes Ln(btfa)\({}_{3} \cdot 2\hbox {H}_{2}\)O (Ln\(^{3+}\): Eu\(^{3+}\), Sm\(^{3+ }\), and Tb\(^{3+}\); btfa: 4,4,4-trifluoro-l-phenyl-1,3-butanedione) were incorporated into silica gels by a sol–gel method. Photoacoustic (PA) spectra of these complex-doped silica samples were measured and studied. The PA intensity of the \(\beta \)-diketonate ligand is nearly the same for lanthanide complexes in wet gels. After heat treatment at 150 \(^{\circ }\)C, however, the PA intensity of the ligand increases for Eu\(^{3+}\), Sm\(^{3+}\), and Tb\(^{3+}\) complexes in silica gels, respectively. Different PA intensities of the samples are interpreted by comparison with their luminescence spectra. The luminescence result is consistent with the PA spectra. The result indicates that lanthanide \(\beta \)-diketonate complexes cannot be formed in silica gels without a suitable heat treatment. Moreover, the relaxation process model is proposed based on the PA and luminescence results.     

Thermo-transport properties of Zn-substituted layered Li-nickel oxide, $$\hbox {LiNiO}_{2}$$

The layered Li-TM-\(\hbox {O}_{2}\) materials have been investigated extensively due to their application as cathodes in Li batteries. The electrical properties of these oxides can be tuned or controlled either by non-stoichiometry or substitution. Hence the thermo-transport properties of Zn-substituted \(\hbox {LiNi}_{1-x}\hbox {Zn}_{x}\hbox {O}_{2}\) for \(0 \le x \le 0.16\) have been investigated in the temperature range of 300–900 K for potential application as a high-temperature thermoelectric material. For \(x < 0.08\), the compounds were of single phase belonging to the space group R-3mH while for \(x > 0.08\) an additional minority phase, ZnO forms together with the main layered phase. All the compounds exhibit a semiconducting behaviour with electrical resistivity, varying in the range of  \(\sim 10^{-4}\) to \(10^{-2}\,\,\Omega \hbox {m}\) between 300 and 900 K. The electrical resistivity is found to increase with increasing Zn-substitution predominantly due to a decrease in the charge carrier hole mobility. The activation energy remains constant, \(\sim \)10  meV, with Zn-substitution. The Seebeck coefficient of the compounds is found to decrease with increasing temperature and increase with increasing Zn-substitution. The Seebeck coefficient decreases from \(\sim \)95 to \(35\ \upmu \hbox {V K}^{-1}\) and the corresponding power factor is \(\sim \)12\(\ \upmu \hbox {W m}^{-1}\ {\hbox {K}}^{-2}\) for the \(x = 0.16\) compound.     

Physical,optical and structural studies of copper-doped lead oxychloro borate glasses

Bluish coloured glasses are obtained from the composition PbCl\(_{2}\)–PbO–B\(_{2}\)O\(_{3}\) doped with Cu\(^{2+}\) ions. Basic physical properties and spectroscopic studies (optical absorption, electron paramagnetic resonance, Fourier transform infrared and Raman spectroscopies) were carried out on these samples. The increase in PbCl\(_{2}\) content resulted in the decrease in density and increase in molar volume. At optical frequencies, band gaps and Urbach energies were evaluated and their variation is explained. Spin-Hamiltonian parameters (SHP) obtained from the EPR spectra suggest that the ligand environment around Cu\(^{2+}\) is tetragonally distorted octahedral sites and the orbital \(d_{x^{2}-{y}^{2}} \) is the ground state. The characteristics broad bands in the optical absorption spectra are assigned to the \(^{2}\)B\(_{\mathrm{1g}}\,\rightarrow \, {}^{2}\)B\(_{\mathrm{2g}}\) transition. The bonding coefficient values were evaluated using optical data and SHP. FTIR studies suggested that the glass structure is built up of BO\(_{3}\) and BO\(_{4}\) units. The presence of diborate, pyroborate, pentaborate groups, etc. in the glass network was confirmed from Raman spectra.     

Measurement of the Nonlinearity of Heat-Flux Sensors Employing a $$\hbox {CO}_2$$ laser

Heat-flux sensors are widely used in industry to test building products and designs for resistance to bushfire, to test the flammability of textiles and in numerous applications such as concentrated solar collectors. In Australia, such detectors are currently calibrated by the National Measurement Institute Australia (NMIA) at low flux levels of 20 W \(\cdot \) m\(^{-2}\). Estimates of the uncertainty arising from nonlinearity at industrial levels (e.g. 50 kW \(\cdot \) m\(^{-2}\) for bushfire testing) rely on literature information. NMIA has developed a facility to characterize the linearity response of these heat-flux sensors up to 110 kW \(\cdot \) m\(^{-2}\) using a low-power \(\hbox {CO}_2\) laser and a chopped quartz tungsten–halogen lamp. The facility was validated by comparison with the conventional flux-addition method, and used to characterize several Schmidt–Boelter-type sensors. A significant nonlinear response was found, ranging from (\(3.2 \pm 0.9\))% at 40 kW \(\cdot \) m\(^{-2}\) to more than 8 % at 100 kW \(\cdot \) m\(^{-2}\). Additional measurements confirm that this is not attributable to convection effects, but due to the temperature dependence of the sensor’s responsivity.     

Thickness-Dependent Properties of YBCO Films Grown on GZO/CLO-Buffered NiW Substrates

To study the role of novel Gd\(_2\)Zr\(_2\)O\(_7\)/Ce\(_{0.9}\)La\(_{0.1}\)O\(_2\) buffer layer structure on a biaxially textured NiW substrate, a set of YBa\(_2\)Cu\(_3\)O\(_{7-\delta }\) (YBCO) films with different thicknesses were prepared by pulsed laser deposition (PLD). Interface imperfections as well as thickness-dependent structural properties were observed in the YBCO thin films. The structure is also reflected into the improved superconducting properties with the highest critical current densities in films with intermediate thicknesses. Therefore, it can be concluded that the existing buffer layers need more optimization before they can be successfully used for films with various thicknesses. This issue is linked to the extremely susceptible growth method of PLD when compared to the commonly used chemical deposition methods. Nevertheless, PLD-grown films can give a hint on what to concentrate to be able to further improve the buffer layer structures for future coated conductor technologies.     

Evolution of magnetic structure of Dy(Co<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Ni<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>)<Subscript>2</Subscript>B<Subscript>2</Subscript>C

DyNi\(_{2}\)B\(_{2}\)C superconducts at \(T_{c} \approx 6\,{\text{K}}\) and orders antiferromagnetically at \(T_{N}\approx 10\,{\text{K}}.\) Its non-superconducting isomorph DyCo\(_{2}\)B\(_{2}\)C is a ferromagnet with \(T_{C}\approx 6\,{\text{K}}.\) With the aim of mapping out the magnetic properties, in particular magnetic structures, of their solid solutions, we synthesized \(^{11}\)B-enriched Dy(Co\(_{x}\)Ni\(_{1-x}\))\(_{2}\)B\(_{2}\)C (\(x=0.2,0.4,0.6,0.8\)). We investigated the evolution of their magnetic, thermal and transport properties by means of the magnetization, resistivity, specific heat and neutron diffraction techniques. Their crystal structures were confirmed to be ThCr\(_{2}\)-Si\(_{2}\)-type tetragonal (I4/mmm) phase. The magnetic structure was found to be antiferromagnetic with k_0.2 = (0, 0, 1) for x = 0.2; helicoidal with k\(_{0.4}\) = (0, 0, 0.49) and k\(_{0.6}\) = (0, 0, 0.46) for, respectively, x = 0.4 and 0.6 and ferromagnetic with k\(_{0.8}\) = (0, 0, 0) for x = 0.8. We discuss the evolution of such magnetic modes assuming a scenario of an idealized one-dimensional chain of transverse magnetic moments.     

The Influence of Impurities on the Zinc Fixed Point

Impurities are considered to be the most significant source of uncertainty for the realization of the International Temperature Scale of 1990 by means of metal fixed points. The determination and further reduction in this uncertainty require a traceable chemical analysis of dissolved impurities in the fixed-point metal and accurate knowledge of the specific temperature change caused by impurities (slope of the liquidus line). We determined the slope of the liquidus line for three binary systems and present results and conclusions from the chemical analysis of zinc with a nominal purity of 7N. For the Fe–Zn system, we determined a liquidus slope of (\(-0.91\pm 0.14\)) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)) from the evaluation of freezing plateaus and (\(-0.76~\pm 0.20\)) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)) from the evaluation of melting plateaus; for the Pb–Zn system, the corresponding results are (\(-0.27~\pm 0.05\)) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)) and (\(-0.26~\pm 0.05\)) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)). Although for the Sb–Zn system, we determined a liquidus slope of about \(-0.8\) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)), our investigations showed that a correction of the influence of antimony is highly questionable because antimony can be found in zinc in a fully dissolved state or precipitated as an insoluble compound. Iron is the only impurity where a correction of the fixed-point temperature was possible. For the realization of the zinc fixed point at PTB, this correction is between 2 \(\upmu \)K and 16 \(\upmu \)K depending on the batch of zinc used. The influence of the sum of all impurities was estimated by means of the OME method. The resulting uncertainty contribution is between 12 \({\upmu }\hbox {K}\) and 48 \({\upmu }\hbox {K}\).     

Further Estimates of $$(T-T_{90})$$ Close to the Triple Point of Water

Recent advances in primary acoustic gas thermometry (AGT) have revealed significant differences between temperature measurements using the International Temperature Scale of 1990, \(T_{90}\), and thermodynamic temperature, T. In 2015, we published estimates of the differences \((T-T_{90})\) from 118 K to 303 K, which showed interesting behavior in the region around the triple point of water, \(T_\mathrm{TPW}=273.16\) K. In that work, the \(T_{90}\) measurements below \(T_\mathrm{TPW}\) used a different ensemble of capsule standard platinum resistance thermometers (SPRTs) than the \(T_{90}\) measurements above \(T_\mathrm{TPW}\). In this work, we extend our earlier measurements using the same ensemble of SPRTs above and below \(T_\mathrm{TPW}\), enabling a deeper analysis of the slope \(\mathrm{d}(T-T_{90})/\mathrm{d}T\) around \(T_\mathrm{TPW}\). In this article, we present the results of seven AGT isotherms in the temperature range 258 K to 323 K. The derived values of \((T-T_{90})\) have exceptionally low uncertainties and are in good agreement with our previous data and other AGT results. We present the values \((T-T_{90})\) alongside our previous estimates, with the resistance ratios W(T) from two SPRTs which have been used across the full range 118 K to 323 K. Additionally, our measurements show discontinuities in \(\mathrm{d}(T-T_{90})/\mathrm{d}T\) at \(T_\mathrm{TPW}\) which are consistent with the slope discontinuity in the SPRT deviation functions. Since this discontinuity is by definition non-unique, and can take a range of values including zero, we suggest that mathematical representations of \((T-T_{90})\), such as those in the mise en pratique for the kelvin (Fellmuth et al. in Philos Trans R Soc A 374:20150037, 2016. doi: 10.1098/rsta.2015.0037), should have continuity of \(\mathrm{d}(T-T_{90})/\mathrm{d}T\) at \(T_\mathrm{TPW}\).     

Mesoscale evolution of non-graphitizing pyrolytic carbon in aligned carbon nanotube carbon matrix nanocomposites

Polymer-derived pyrolytic carbons (PyCs) are highly desirable building blocks for high-strength low-density ceramic meta-materials, and reinforcement with nanofibers is of interest to address brittleness and tailor multi-functional properties. The properties of carbon nanotubes (CNTs) make them leading candidates for nanocomposite reinforcement, but how CNT confinement influences the structural evolution of the PyC matrix is unknown. Here, the influence of aligned CNT proximity interactions on nano- and mesoscale structural evolution of phenol-formaldehyde-derived PyCs is established as a function of pyrolysis temperature (\(T_{\mathrm {p}}\)) using X-ray diffraction, Raman spectroscopy, and Fourier transform infrared spectroscopy. Aligned CNT PyC matrix nanocomposites are found to evolve faster at the mesoscale by plateauing in crystallite size at \(T_{\mathrm {p}}\) \(\sim\)800 \(^{\circ }\hbox {C}\), which is more than \(200\,\,^{\circ }\hbox {C}\) below that of unconfined PyCs. Since the aligned CNTs used here exhibit \(\sim\)80 nm average separations and \(\sim\)8 nm diameters, confinement effects are surprisingly not found to influence PyC structure on the atomic-scale at \(T_{\mathrm {p}}\) \(\le \)1400 \(^{\circ }\hbox {C}\). Since CNT confinement could lead to anisotropic crystallite growth in PyCs synthesized below \(\sim\)1000 \(^{\circ }\hbox {C}\), and recent modeling indicates that more slender crystallites increase PyC hardness, these results inform fabrication of PyC-based meta-materials with unrivaled specific mechanical properties.     

Study of $$\upbeta $$-phase development in spin-coated PVDF thick films

A study was conducted to ascertain the effect of variation in spin speed and baking temperature on \(\upbeta \)-phase content in the spin-coated poly(vinylidene fluoride) (PVDF) thick films (\({\sim }4{-}25\,\upmu \hbox {m}\)). Development of \(\upbeta \)-phase is dependent on film stretching and crystallization temperature. Therefore, to study the development of \(\upbeta \)-phase in films, stretching is achieved by spinning and crystallization temperature is adjusted by means of baking. PVDF films are characterized using Fourier transform infrared spectroscopy, X-ray diffraction, differential scanning calorimetry, and scanning electron microscopy. It is observed that crystallization temperature lower than \(60^{\circ }\hbox {C}\) and increase in spin speed increases the \(\upbeta \)-phase content in PVDF films. Crystallization temperature above \(60^{\circ }\hbox {C}\) reduces \(\upbeta \)-phase content and increases \(\upalpha \)-phase content. It was also observed that viscosity of the PVDF solution affects the \(\upbeta \)-phase development in films at a particular spin speed.     

Temperature effects on the electrical characteristics of $$\mathrm{Al}/\mathrm{PTh}-\mathrm{SiO}_{2}/\mathrm{p\hbox {-}Si}$$ structure

The temperature-dependent current–voltage (\(I\text {--}V\)) and capacitance–voltage (\(C\text {--}V\)) characteristics of the fabricated Al/p-Si Schottky diodes with the polythiopene–SiO\(_{2}\) nanocomposite (\(\hbox {PTh--SiO}_{2}\)) interlayer were investigated. The ideality factor of \(\hbox {Al}/\hbox {PTh--SiO}_{2}/{p}\text {-Si}\) Schottky diodes has decreased with increasing temperature and the barrier height has increased with increasing temperature. The change in the barrier height and ideality factor values with temperature was attributed to inhomogeneties of the zero-bias barrier height. Richardson plot has exhibited curved behaviour due to temperature dependence of barrier height. The activation energy and effective Richardson constant were calculated as 0.16 eV and \(1.79 \times 10^{-8} \hbox {A\,cm}^{-2} \,\hbox {K}^{-2}\) from linear part of Richardson plots, respectively. The barrier height values determined from capacitance–voltage–temperature (\(C\text {--}V\text {--}T\)) measurements decrease with increasing temperature on the contrary of barrier height values obtained from \(I\text {--}V\text {--}T\) measurements.     

Bootstrap in semi-functional partial linear regression under dependence

This paper deals with the semi-functional partial linear regression model \(Y={{\varvec{X}}}^\mathrm{T}{\varvec{\beta }}+m({\varvec{\chi }})+\varepsilon \) under \(\alpha \)-mixing conditions. \({\varvec{\beta }} \in \mathbb {R}^{p}\) and \(m(\cdot )\) denote an unknown vector and an unknown smooth real-valued operator, respectively. The covariates \({{\varvec{X}}}\) and \({\varvec{\chi }}\) are valued in \(\mathbb {R}^{p}\) and some infinite-dimensional space, respectively, and the random error \(\varepsilon \) verifies \(\mathbb {E}(\varepsilon |{{\varvec{X}}},{\varvec{\chi }})=0\). Naïve and wild bootstrap procedures are proposed to approximate the distribution of kernel-based estimators of \({\varvec{\beta }}\) and \(m(\chi )\), and their asymptotic validities are obtained. A simulation study shows the behavior (on finite sample sizes) of the proposed bootstrap methodology when applied to construct confidence intervals, while an application to real data concerning electricity market illustrates its usefulness in practice.     

Effect of Pressure on Deep-Ocean Thermometers

A laboratory experiment was devised and performed to investigate the pressure dependence of Sea-Bird Electronics SBE35 and SBE3 deep-ocean thermometers. The thermometers were mounted in a massive brass comparator together with a calibrated standard platinum resistance thermometer. The measurements were performed in a pressure chamber in the pressure range 0.1 MPa to 60 MPa. The results showed that both the investigated SBE35 and SBE3 thermometers are pressure dependent, with a pressure sensitivity of +41 \(\upmu \)K\(\cdot \)MPa\(^{-1}\) and \(-77\) \(\upmu \)K\(\cdot \)MPa\(^{-1}\), respectively. Nevertheless, the results obtained in only one individual device per model (one SBE35 and one SBE3) cannot be generalized and further investigations of a larger number of devices per model are needed.     

Microwave-hydrothermal synthesis of mesoporous $$\upgamma $$-$$\hbox {Al}_{2}\hbox {O}_{3}$$Al2O3 and its impregnation with AgNPs for excellent catalytic oxidation of CO

Mesoporous \(\upgamma \)-alumina was synthesized by the microwave-hydrothermal process with a shorter duration time at 150\({^{\circ }}\)C/2 h followed by calcination at 550\({^{\circ }}\)C/1 h. Ag nanoparticles (AgNPs) were impregnated into \(\upgamma \)-alumina under a reducing atmosphere at 450\({^{\circ }}\)C. The synthesized product was characterized by X-ray diffraction (XRD), thermogravimetric (TG)/differential thermal analysis (DTA), X-ray photoelectron spectroscopy (XPS), \(\hbox {N}_{2}\) adsorption–desorption study, field-emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). The BET surface area values of \(\upgamma \)-alumina and Ag-impregnated \(\upgamma \)-alumina were found to be 258 and 230 m\(^{2}\) g\(^{-1}\), respectively. FESEM images showed the formation of grain-like particles of 50–70 nm in size with a flake-like microstructure. The XRD, XPS and TEM studies confirmed the presence of Ag in the synthesized product. Catalytic properties of the product for CO oxidation was studied with the \(T_{50}\) (50% conversion) and \(T_{100}\) (100% conversion) values of 118 and 135\({^{\circ }}\)C, respectively; the enhanced values were compared with the literature reported values.     

Characterization and optical properties of $$\hbox {Pr}_{2}\hbox {O}_{3}$$-doped molybdenum lead-borate glasses

\(\hbox {Pr}^{3+}\) doped molybdenum lead-borate glasses with the chemical composition 75PbO?[25–(x \(+\) y)\(\hbox {B}_{2}\hbox {O}_{3}]\)–\(y\hbox {MoO}_{3}\)–\(x\hbox {Pr}_{2}\hbox {O}_{3}\) (where \(x = 0.5\) and 1.0 mol% and \(y = 0\) and 5 mol%) were prepared by conventional melt-quenching technique. Thermal, optical and structural analyses are carried out using DSC, UV and FTIR spectra. The physical parameters, like glass transition \((T_{\mathrm{g}})\), stability factor \((\Delta T)\), optical energy band gap \((E_{\mathrm{gopt}})\), of these glasses have been determined as a function of dopant concentration. The \({T}_{\mathrm{g}}\) and optical energy gaps of these glasses were found to be in the range of 290–350\({^{\circ }}\hbox {C}\) and 2.45–2.7 eV, respectively. Stability of the glass doped with \(\hbox {Pr}^{3+}\) is found to be moderate (\(\sim \)40). The results are discussed using the structural model of Mo–lead-borate glass.     

Density Functional Study of the Carbon Dependence of the Structural,Mechanic, Thermodynamic,and Dynamic Properties of SiC Alloys

Using a density functional scheme, for the first time the carbon dependence on the structural, dynamic, thermodynamic, and dynamic properties of \(\hbox {Si}_{1-x}\hbox {C}_{x} \) alloys (\(x=0.0\) to 1.0 in steps of 0.125) has been investigated. The structural properties of these materials, in particular, the composition dependence of the lattice parameter and bulk modulus, are in excellent agreement with experimental data and follow a quadratic law in (x). A nonlinear relationship is found between the elastic constants \(C_{11}\), \(C_{12}\), and \(C_{44}\) and the carbon concentration (x). The behavior of the acoustical and optical phonon frequencies at high-symmetry points \(\varGamma \), X, and L is predicted. Through the quasi-harmonic Debye model, in which the photonic effects are taken into account, the Debye temperature, the heat capacity, the Helmholtz free energy, the internal energy, and the entropy are determined for the \(\hbox {Si}_{1-x}\hbox {C}_{x }\) compounds.     

Thermal Conductivity of Pyroclastic Soil (<Emphasis Type="BoldItalic">Pozzolana</Emphasis>) from the Environs of Rome

The paper reveals the experimental procedure and thermo-physical characteristics of a coarse pyroclastic soil (Pozzolana), from the neighborhoods of Rome, Italy. The tested samples are comprised of 70.7 % sand, 25.9 % silt, and 3.4 % clay. Their mineral composition contained 38 % pyroxene, 33 % analcime, 20 % leucite, 6 % illite/muscovite, 3 % magnetite, and no quartz content was noted. The effective thermal conductivity of minerals was assessed to be about \(2.14\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\). A transient thermal probe method was applied to measure the thermal conductivity (\(\lambda \)) over a full range of the degree of saturation \((S_{\mathrm{r}})\), at two porosities (n) of 0.44 and 0.50, and at room temperature of about \(25\,^{\circ }\hbox {C}\). The \(\lambda \) data obtained were consistent between tests and showed an increasing trend with increasing \(S_{\mathrm{r}}\) and decreasing n. At full saturation (\(S_{\mathrm{r}}=1\)), a nearly quintuple \(\lambda \) increase was observed with respect to full dryness (\(S_{\mathrm{r}}=0\)). In general, the measured data closely followed the natural trend of \(\lambda \) versus \(S_{\mathrm{r}}\) exhibited by published data at room temperature for other unsaturated soils and sands. The measured \(\lambda \) data had an average root-mean-squared error (RMSE) of \(0.007\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\) and \(0.008\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\) for n of 0.50 and 0.44, respectively, as well as an average relative standard deviation of the mean at the 95 % confidence level \((\hbox {RSDM}_{0.95})\) of 2.21 % and 2.72  % for n of 0.50 and 0.44, respectively.