Thermo-transport properties of Zn-substituted layered Li-nickel oxide, $$\hbox {LiNiO}_{2}$$

The layered Li-TM-\(\hbox {O}_{2}\) materials have been investigated extensively due to their application as cathodes in Li batteries. The electrical properties of these oxides can be tuned or controlled either by non-stoichiometry or substitution. Hence the thermo-transport properties of Zn-substituted \(\hbox {LiNi}_{1-x}\hbox {Zn}_{x}\hbox {O}_{2}\) for \(0 \le x \le 0.16\) have been investigated in the temperature range of 300–900 K for potential application as a high-temperature thermoelectric material. For \(x < 0.08\), the compounds were of single phase belonging to the space group R-3mH while for \(x > 0.08\) an additional minority phase, ZnO forms together with the main layered phase. All the compounds exhibit a semiconducting behaviour with electrical resistivity, varying in the range of  \(\sim 10^{-4}\) to \(10^{-2}\,\,\Omega \hbox {m}\) between 300 and 900 K. The electrical resistivity is found to increase with increasing Zn-substitution predominantly due to a decrease in the charge carrier hole mobility. The activation energy remains constant, \(\sim \)10  meV, with Zn-substitution. The Seebeck coefficient of the compounds is found to decrease with increasing temperature and increase with increasing Zn-substitution. The Seebeck coefficient decreases from \(\sim \)95 to \(35\ \upmu \hbox {V K}^{-1}\) and the corresponding power factor is \(\sim \)12\(\ \upmu \hbox {W m}^{-1}\ {\hbox {K}}^{-2}\) for the \(x = 0.16\) compound.     

High-Accuracy Emissivity Data on the Coatings Nextel 811-21, Herberts 1534, Aeroglaze Z306 and Acktar Fractal Black

The Physikalisch-Technische Bundesanstalt determined the directional spectral emissivities of several widely used black coatings: Nextel 811-21, Herberts 1534, Aeroglaze Z306 and Acktar Fractal Black. These are and were often applied in different industrial and scientific applications. The measurements are taken angularly resolved over a range from \(10{^{\circ }}\) to \(70{^{\circ }}\). They cover the temperature range typical for the application of the respective coating and a wide wavelength range from \(4~\upmu \hbox {m}\) to \(100~\upmu \hbox {m}\). The respective directional total emissivities and hemispherical total emissivities are given as well. The measurements were taken under vacuum at the reduced background calibration facility to achieve low uncertainties and avoid atmospheric interferences. Additionally, some measurements were taken with the emissivity measurement setup in air.     

Hydrothermal growth of wheatear-shaped ZnO microstructures and their photocatalytic activity

A facile hydrothermal process was developed to synthesize novel wheatear-shaped ZnO microstructures at a low temperature (\(85^{\circ }\hbox {C}\)) without the assistance of any template agent. X-ray diffraction and field emission scanning electron microscopy were used to characterize the structure and morphology of the samples. Results showed that the length of the ‘wheatear’ was about \(5.8~\upmu \!\hbox {m}\) and the section width was \(1.2~\upmu \!\hbox {m}\). The particles consisted of closely packed nanorods with average diameter of 100 nm. The growth of wheatear-shaped ZnO is very rapid and can be achieved in only 5 min. \(\hbox {OH}^{-}\)-driven oriented aggregation and multistep nucleation resulted in the formation of wheatear-shaped ZnO microstructures. The product had assembled open structures and it exhibited excellent photocatalytic activity in the degradation of methyl orange under UV-light irradiation.     

The Influence of Impurities on the Zinc Fixed Point

Impurities are considered to be the most significant source of uncertainty for the realization of the International Temperature Scale of 1990 by means of metal fixed points. The determination and further reduction in this uncertainty require a traceable chemical analysis of dissolved impurities in the fixed-point metal and accurate knowledge of the specific temperature change caused by impurities (slope of the liquidus line). We determined the slope of the liquidus line for three binary systems and present results and conclusions from the chemical analysis of zinc with a nominal purity of 7N. For the Fe–Zn system, we determined a liquidus slope of (\(-0.91\pm 0.14\)) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)) from the evaluation of freezing plateaus and (\(-0.76~\pm 0.20\)) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)) from the evaluation of melting plateaus; for the Pb–Zn system, the corresponding results are (\(-0.27~\pm 0.05\)) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)) and (\(-0.26~\pm 0.05\)) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)). Although for the Sb–Zn system, we determined a liquidus slope of about \(-0.8\) mK / (\(\upmu \hbox {g}{\cdot }\hbox { g}^{-1}\)), our investigations showed that a correction of the influence of antimony is highly questionable because antimony can be found in zinc in a fully dissolved state or precipitated as an insoluble compound. Iron is the only impurity where a correction of the fixed-point temperature was possible. For the realization of the zinc fixed point at PTB, this correction is between 2 \(\upmu \)K and 16 \(\upmu \)K depending on the batch of zinc used. The influence of the sum of all impurities was estimated by means of the OME method. The resulting uncertainty contribution is between 12 \({\upmu }\hbox {K}\) and 48 \({\upmu }\hbox {K}\).     

Emission of Gas and $$\hbox {Al}_{2}\hbox {O}_{3}$$ Smoke in Gas–Al Particle Deflagration: Experiments and Emission Modeling for Explosive Fireballs

Emission of gas and \(\hbox {Al}_{2}\hbox {O}_{3}\) smoke within the deflagration of \(\hbox {H}_{2}{-}\hbox {O}_{2}\)–{\(\hbox {N}_{2}{-}\hbox {CO}_{2}\)}–Al particles has been studied in a closed combustion chamber at pressures of up to 18 bar and at gas temperatures of up to 3700 K. Measurements of radiance intensity were taken using a five wavelength pyrometer (0.660 \(\upmu \hbox {m}\), 0.850 \(\upmu \hbox {m}\), 1.083 \(\upmu \hbox {m}\), 1.260 \(\upmu \hbox {m}\), 1.481 \(\upmu \hbox {m}\)) and a grating spectrometer in the range (4.10 \(\upmu \hbox {m}\) to 4.30 \(\upmu \hbox {m}\)). In order to characterize the aluminum oxide smoke size and temperature, an inversion method has been developed based on the radiation transfer equation and using pyrometer measurements and thermochemical calculations of \(\hbox {Al}_{2}\hbox {O}_{3}\) smoke volume fractions. Temperatures in combustion gas have been determined using a method based on the assumed blackbody head of the 4.26 \(\upmu \hbox {m}\) \(\hbox {CO}_{2}\) emission line and on its spectral shift with pressure and temperature. For validation purpose, this method has been applied to measurements obtained when calibrated alumina particles are injected in a combustion chamber prior to gaseous deflagrations. This mathematical inversion method was developed to investigate explosive fireballs.     

Estimating the Kinematic Viscosity of Petroleum Fractions

Kinematic viscosity correlation has been developed for liquid petroleum fractions at 37.78\(\,^{\circ }\hbox {C}\) and \(98.89\,^{\circ }\hbox {C}\) (100 and \(210^{\circ }\hbox {F})\) standard temperatures using a large variety of experimental data. The only required inputs are the specific gravity and the average boiling point temperature. The accuracy of the correlation was compared with several other correlations available in the literature. The proposed correlations proved to be more accurate in predicting the viscosity at 37.78\(\,^{\circ }\hbox {C}\) and \(98.89\,^{\circ }\hbox {C}\) with average absolute deviations of 0.39 and \(0.72\hbox { mm}^{2}/\hbox {s}\), respectively. Another objective was to develop a relation for the variation of viscosity with temperature to predict the viscosity of petroleum fraction at a certain temperature from the knowledge of the viscosity for the same liquid at two other temperatures. The newly developed correlation represents a wide array of temperatures from 20 \(^{\circ }\hbox {C}\) to 150 \(^{\circ }\hbox {C}\) and viscosities from 0.14\(\hbox { mm}^{2}/\hbox {s}\) to 343.64\(\hbox { mm}^{2}/\hbox {s}\). The results have been validated with experimental data consisting of 9558 data points, yielding an overall deviation of \(0.248\hbox { mm}^{2}/\hbox {s}\) and \(\hbox {R}^{2}\) of 0.998. In addition, new formulas were developed to interconvert the viscosity of petroleum fractions from one unit of measure to another based on finding the best fit for a set of experimental data from the literature with \(R^{2}\) as high as 1.0 for many cases. Detailed analysis showed good agreement between the predicted values and the experimental data.     

Temperature effects on the electrical characteristics of $$\mathrm{Al}/\mathrm{PTh}-\mathrm{SiO}_{2}/\mathrm{p\hbox {-}Si}$$ structure

The temperature-dependent current–voltage (\(I\text {--}V\)) and capacitance–voltage (\(C\text {--}V\)) characteristics of the fabricated Al/p-Si Schottky diodes with the polythiopene–SiO\(_{2}\) nanocomposite (\(\hbox {PTh--SiO}_{2}\)) interlayer were investigated. The ideality factor of \(\hbox {Al}/\hbox {PTh--SiO}_{2}/{p}\text {-Si}\) Schottky diodes has decreased with increasing temperature and the barrier height has increased with increasing temperature. The change in the barrier height and ideality factor values with temperature was attributed to inhomogeneties of the zero-bias barrier height. Richardson plot has exhibited curved behaviour due to temperature dependence of barrier height. The activation energy and effective Richardson constant were calculated as 0.16 eV and \(1.79 \times 10^{-8} \hbox {A\,cm}^{-2} \,\hbox {K}^{-2}\) from linear part of Richardson plots, respectively. The barrier height values determined from capacitance–voltage–temperature (\(C\text {--}V\text {--}T\)) measurements decrease with increasing temperature on the contrary of barrier height values obtained from \(I\text {--}V\text {--}T\) measurements.     

Microfocus Bremsstrahlung Source Based on a Narrow Internal Target of a Betatron

The paper addresses the research into the properties of bremsstrahlung generated by interaction of the internal electron beam of the 18 MeV betatron with narrow targets, 50 and \(8 \,\upmu \hbox {m}\) thick Si crystals and \(13 \,\upmu \hbox {m}\) thick Ta foil with a length of 4 mm along the electron beam, mounted in the goniometer inside the betatron chamber. The radiation beams generated in the targets were used to obtain the images of a microstructure of thin wire pairs and an object that consisted of four steel bars with \(10\, \upmu \hbox {m}\) gaps between them. The images indicate high absorption contrast of their components due to a small horizontal size of the radiation source the width of which in the cases of Si crystals and Ta foil was 30-, 187- and 115-fold smaller than the diameter of the electron beam, respectively. The edge phase-contrast was also observed due to high spatial coherency of the radiation with the linear microfocus generated in the source based on the B-18 betatron with a narrow target inside.     

Thermodynamic Temperature Measurement to the Indium Point Based on Radiance Comparison

A multi-national project (the EMRP InK project) was completed recently, which successfully determined the thermodynamic temperatures of several of the high-temperature fixed points above the copper point. The National Metrology Institute of Japan contributed to this project with its newly established absolute spectral radiance calibration capability. In the current study, we have extended the range of thermodynamic temperature measurement to below the copper point and measured the thermodynamic temperatures of the indium point (\(T_{90} =\) 429.748 5 \(\hbox {K}\)), tin point (505.078 K), zinc point (692.677 K), aluminum point (933.473 K) and the silver point (1 234.93 K) by radiance comparison against the copper point, with a set of radiation thermometers having center wavelengths ranging from \(0.65\,\upmu \hbox {m}\) to \(1.6\,\upmu \hbox {m}\). The copper-point temperature was measured by the absolute radiation thermometer which was calibrated by radiance method traceable to the electrical substitution cryogenic radiometer. The radiance of the fixed-point blackbodies was measured by standard radiation thermometers whose spectral responsivity and nonlinearity are precisely evaluated, and then the thermodynamic temperatures were determined from radiance ratios to the copper point. The values of \(T-T_{90}\) for the silver-, aluminum-, zinc-, tin- and indium-point cells were determined as ?4 mK (\(U = 104\,\hbox {mK}, k=2\)), ?99 mK (88 mK), ?76 mK (76 mK), ?68 mK (163 mK) and ?42 mK (279 mK), respectively.     

Structural,dielectric and piezoelectric study of Ca-, Zr-modified $$\hbox {BaTiO}_{3}$$ lead-free ceramics

We prepared a lead-free ceramic (\(\hbox {Ba}_{0.85}\hbox {Ca}_{0.15})(\hbox {Ti}_{1-x}\hbox {Zr}_{x})\hbox {O}_{3}\) (BCTZ) using the conventional mixed oxide technique. The samples were prepared by an ordinary mixing and sintering technique. In this study we investigated how small amounts of \(\hbox {Zr}^{4+}\) can affect the crystal structure and microstructure as well as dielectric and piezoelectric properties of \(\hbox {BaTiO}_{3}\). X-ray diffraction analysis results indicate that no secondary phase is formed in any of the BCTZ powders for \(0 \le x \le 0.1\), suggesting that \(\hbox {Zr}^{4+}\) diffuses into \(\hbox {BaTiO}_{3}\) lattices to form a solid solution. Scanning electron microscopy micrographs revealed that the average grain size gradually increased with \(\hbox {Zr}^{4+}\) content from 9.5 \(\upmu \!\hbox {m}\) for \(x = 0.02\) to 13.5 \(\upmu \!\hbox {m}\) for \(x = 0.1\); Curie temperature decreased due to the small tetragonality caused by \(\hbox {Zr}^{4+}\) addition. Owing to the polymorphic phase transition from orthorhombic to tetragonal phase around room temperature, it was found that the composition \(x = 0.09\) showed improved electrical properties and reached preferred values of \(d_{33} = 148\) pC \(\hbox {N}^{-1}\) and \(K_{\mathrm{p}} = 27\%\).     

Radiative Properties of Ceramic $$\hbox {Al}_{2}\hbox {O}_{3}$$, AlN,and $$\hbox {Si}_{3}\hbox {N}_{4}$$Si3N4: I. Experiments

The radiative properties of dense ceramic \(\hbox {Al}_{2}\hbox {O}_{3}\), AlN, and \(\hbox {Si}_{3}\hbox {N}_{4}\) plates are investigated from the visible to the mid-infrared region at room temperature. Each specimen has different surface finishings on different sides of the laminate. A monochromator was used with an integrating sphere to measure the directional-hemispherical reflectance and transmittance of these samples at wavelengths from 0.4 \(\upmu \hbox {m}\) to 1.8 \(\upmu \hbox {m}\). The specular reflectance was obtained by a subtraction technique. A Fourier-transform infrared spectrometer was used to measure the directional-hemispherical or specular reflectance and transmittance with appropriate accessories from about 1.6 \(\upmu \hbox {m}\) to 19 \(\upmu \hbox {m}\). All measurements were performed at near-normal incidence on either the smooth side or the rough side of the sample. The experimental observations are qualitatively interpreted considering the optical constants, surface roughness, and volume scattering and absorption.     

Radiative Properties of Ceramic $$\hbox {Al}_{2}\hbox {O}_{3}$$, AlN and $$\hbox {Si}_{3}\hbox {N}_{4}$$Si3N4—II: Modeling

In Part I of this study (Cheng et al. in Int J Thermophys 37: 62, 2016), the reflectance and transmittance of dense ceramic plates were measured at wavelengths from 0.4 \(\upmu \hbox {m}\) to about 20 \(\upmu \hbox {m}\). The samples of \(\hbox {Al}_{2}\hbox {O}_{3}\) and AlN are semitransparent in the wavelength region from 0.4 \(\upmu \hbox {m}\) to about 7 \(\upmu \hbox {m}\), where volume scattering dominates the absorption and scattering behaviors. On the other hand, the \(\hbox {Si}_{3}\hbox {N}_{4}\) plate is opaque in the whole wavelength region. In the mid-infrared region, all samples show phonon vibration bands and surface reflection appears to be strong. The present study focuses on modeling the radiative properties and uses an inverse method to obtain the scattering and absorption coefficients of \(\hbox {Al}_{2}\hbox {O}_{3}\) and AlN in the semitransparent region from the measured directional-hemispherical reflectance and transmittance. The scattering coefficient is also predicted using Mie theory for comparison. The Lorentz oscillator model is applied to fit the reflectance spectra of AlN and \(\hbox {Si}_{3}\hbox {N}_{4}\) from 1.6 \(\upmu \hbox {m}\) to 20 \(\upmu \hbox {m}\) in order to obtain their optical constants. It is found that the phonon modes for \(\hbox {Si}_{3}\hbox {N}_{4}\) are much stronger in the polycrystalline sample studied here than in amorphous films reported previously.     

Phase transformation kinetics and microstructure of NiTi shape memory alloy: effect of hydrostatic pressure

The effect of hydrostatic pressure on the behaviour of reverse and forward transformation temperatures and physical properties of NiTi shape memory alloy has been investigated. The transformation temperatures and physical properties of the alloy change with applied pressure. It has been clearly seen from differential scanning calorimetry that with the increase of applied pressure, while \(A_\mathrm{s},\, A_\mathrm{f}\) and \(M_\mathrm{f}\) transformation temperatures decrease, \(M_\mathrm{s}\) value increases. Moreover, it is obvious that with the increase of applied pressure, Gibbs free energy increases by 5.2883 J, while elastic energy increases by 1.4687 J. In addition, entropy of the alloys decreases by 0.2335 J \((\hbox {g }{^{\circ }}\!\hbox { C})^{-1}\) with applied pressure. Additionally, it is evident from the scanning electron microscopy images of the samples that there is an obvious difference in the grain sizes of the unpressured sample and the samples on which pressure is applied, the sizes being 10–100 and 30–150 \(\upmu \!\hbox {m}\), respectively.     

Magnetism in Solid Oxygen Studied by High-Pressure Neutron Diffraction

A systematic modification of the entropy trajectory (\(S_\mathrm{m}(T)\)) is observed at very low temperature in magnetically frustrated systems as a consequence of the constraint (\(S_\mathrm{m}\ge 0\)) imposed by the Nernst postulate. The lack of magnetic order allows to explore and compare new thermodynamic properties by tracing the specific heat (\(C_\mathrm{m}\)) behavior down to the sub-Kelvin range. Some of the most relevant findings are: (i) a common \(C_\mathrm{m}/T|_{T\rightarrow 0} \approx 7\) J/mol K\(^2\) ‘plateau’ in at least five Yb-based very-heavy-fermions (VHF) compounds; (ii) quantitative and qualitative differences between VHF and standard non-Fermi-liquids; (iii) entropy bottlenecks governing the change of \(S_\mathrm{m}(T)\) trajectories in a continuous transition into alternative ground states. A comparative analysis of \(S_\mathrm{m}(T\rightarrow 0)\) dependencies is performed in compounds suitable for adiabatic demagnetization processes according to their \(\partial ^2 S_\mathrm{m}/\partial T^2\) derivatives.     

Influences of Detection Pinhole and Sample Flow on Thermal Lens Detection in Microfluidic Systems

Thermal lens microscopy (TLM), due to its high temporal (\({\sim }\mathrm{ms}\)) and spatial resolution (\({\sim }\upmu \mathrm{m}\)), has been coupled to lab-on-chip chemistry for detection of a variety of compounds in chemical or biological fields. Due to the very short optical path length (usually below 100 \(\upmu \mathrm{m}\)) in a microchip, the sensitivity of TLM is unfortunately still 10 to 100 times lower than conventional TLS with 1 cm sample length. Optimization of the TLM optical configuration was made with respect to different pinhole aperture-to-beam size ratios for the best signal-to-noise ratio. In the static mode, the instrumental noise comes mainly from the shot noise of the probe beam when the chopper frequency is over 1 kHz or from the flicker noise of the probe beam at low frequencies. In the flowing mode, the flow-induced noise becomes dominant when the flow rate is high. At a given flow rate, fluids with a higher density and/or a higher viscosity will cause larger flow-induced noise. As an application, a combined microfluidic flow injection analysis (\(\upmu \mathrm{FIA}\))–TLM device was developed for rapid determination of pollutants by colorimetric reactions. Hexavalent chromium [Cr(VI)] was measured as a model analyte. Analytical signals for 12 sample injections in 1 min have been recorded by the \({\upmu }\)FIA–TLM. For injections of sub-\(\upmu \)L samples into the microfluidic stream in a \(50\,\upmu \mathrm{m}\) deep microchannel, a limit of detection of \(4\,\mathrm{ng}{\cdot }\mathrm{mL}^{-1}\) was achieved for Cr(VI) in water at 60 mW excitation power.     

Effects of electrolyte concentration and current density on the properties of electro-deposited NiFeW alloy coatings

NiWP alloy coatings were prepared by electrodeposition, and the effects of ferrous chloride (\(\hbox {FeCl}_{2})\), sodium tungstate (\(\hbox {Na}_{2}\hbox {WO}_{4})\) and current density (\(D_{\mathrm{K}}\)) on the properties of the coatings were studied. The results show that upon increasing the concentration of \(\hbox {FeCl}_{2}\), initially the Fe content of the coating increased and then tended to be stable; the deposition rate and microhardness of coating decreased when the cathodic current efficiency (\(\eta \)) initially increased and then decreased; and for a \(\hbox {FeCl}_{2}\) concentration of \(3.6\, \hbox {g\,l}^{-1}\), the cathodic current efficiency reached its maximum of 74.23%. Upon increasing the concentration of \(\hbox {Na}_{2}\hbox {WO}_{4}\), the W content and microhardness of the coatings increased; the deposition rate and the cathode current efficiency initially increased and then decreased. The cathodic current efficiency reached the maximum value of 70.33% with a \(\hbox {Na}_{2}\hbox {WO}_{4}\) concentration of 50 g \(\hbox {l}^{-1}\), whereas the deposition rate is maximum at 8.67 \(\upmu \hbox {m}\,\hbox {h}^{-1}\) with a \(\hbox {Na}_{2}\hbox {WO}_{4}\) concentration of \(40\, \hbox {g\,l}^{-1}\). Upon increasing the \(D_{\mathrm{K}}\), the deposition rate, microhardness, Fe and W content of the coatings increased, the cathodic current efficiency increases first increased and then decreased. When \(D_{\mathrm{K}}\) was 4 A dm\(^{-2}\), the current efficiency reached the maximum of 73.64%.     

Nonlinear Ultrasound Propagation in Solid $$^4\hbox {He}$$ Compared with Shear Modulus Experiments

Ultrasound attenuation (\(\alpha \)) and velocity (V) at 9.6 MHz are measured in polycrystalline hcp \(^4\hbox {He}\). The ultrasound signal above 200 mK is linear and understood in terms of resonant vibration of dislocation segments pinned between network nodes with an average pinning length of 3.7 \(\mu \hbox {m}\), much shorter than 59 \(\mu \hbox {m}\) estimated from a shear modulus measurement. Dramatic changes in \(\alpha \) and V are observed below 200 mK. The changes are strongly dependent on temperature and are nonlinear and hysteretic. These effects result from pinning of dislocations by \(^3\hbox {He}\) impurities (nominal concentration of 0.3 ppm). The dislocation damping constant due to thermal phonons, the binding energy between dislocation and \(^3\hbox {He}\), and the average network pinning length obtained from the ultrasound data are compared with those from the shear modulus experiments.     

Fracture of pre-cracked thin metallic conductors due to electric current induced electromagnetic force

We investigated propagation of a sharp crack in a thin metallic conductor with an edge crack due to electric current induced electromagnetic forces. Finite element method (FEM) simulations showed mode I crack opening in the edge-cracked conductor due to the aforementioned (i.e., self-induced) electromagnetic forces. Mode I stress intensity factor due to the self-induced electromagnetic forces, \(K_{\mathrm{IE},}\) was evaluated numerically as \(K_{\mathrm{IE}}=\upmu l^{2}j^{2}(\uppi a)^{0.5}f(a/w)\), where \(\upmu \) is the magnetic permeability, l is the length of the conductor, a is the crack length, j is the current density, w is the width of the sample and f(a / w) is a geometric factor. Effect of dynamic electric current loading on edge-cracked conductor, incorporating the effects of induced currents, was also studied numerically, and dynamic stress intensity factor, \(K_{\mathrm{IE,d}}\), was observed to vary as \(K_{\mathrm{IE,d}} \sim f_{d}(a/w)j^{2}(\uppi a)^{1.5}\). Consistent with the FEM simulation, experiments conducted using \(12\,\upmu \hbox {m}\) thick Al foil with an edge crack showed propagation of sharp crack due to the self-induced electromagnetic forces at pulsed current densities of \(\ge \) \(1.85\times 10^{9}\,\hbox {A/m}^{2}\) for \(a/w = 0.5\). Further, effects of current density, pulse-width and ambient temperature on the fracture behavior of the Al foil were observed experimentally and corroborated with FEM simulations.     

Effect of CTAB coating on structural,magnetic and peroxidase mimic activity of ferric oxide nanoparticles

In the present work, pristine and cetyl trimethyl ammonium bromide (CTAB)-coated ferric oxide nanoparticles \((\hbox {CTAB@Fe}_{2}\hbox {O}_{3} \hbox { NPs})\) were synthesized and studied as enzyme mimics. The w/w ratio of \(\hbox {Fe}_{2}\hbox {O}_{3}\) to CTAB was varied as 1:1 and 1:2. Transmission electron microscopic analysis revealed that pristine NPs had an average size of 50 nm, whereas the presence of CTAB resulted in the formation of nanorods with length of 130 nm. BET studies confirmed enhancement of surface area on CTAB coating, which was maximum for w/w ratio 1:1. The synthesized pristine NPs and CTAB-coated NPs were evaluated for their peroxidase mimic activity using o-dianisidine dihydrochloride as substrate. Optimum pH, temperature, substrate and NPs concentration for the reaction were 1, \(25^{\circ }{\mathrm{C}}\), \(0.16~\hbox {mg}~\hbox {ml}^{-1}\) and \(1~\hbox {mg}~\hbox {ml}^{-1}\), respectively. Peroxidase mimic activity of \(\hbox {CTAB@Fe}_{2}\hbox {O}_{3}\hbox { NPs}\) (w/w 1:1) was higher than that of pristine NPs. However, further increase in CTAB coating (w/w 1:2) resulted in lowering of peroxidase mimic activity. Kinetic analysis was carried out at optimized conditions; maximum velocity (\(V_{\mathrm{max}})\) and Michaelis constant (\(K_{\mathrm{m}})\) value of \(\hbox {CTAB@Fe}_{2}\hbox {O}_{3}\hbox { NPs}\) at 1:1 w/w ratio were 7.69 mM and \(1.12~\upmu \hbox {mol}~\hbox {s}^{-1}\), respectively.