Model‐based optimization of hydrogen generation by methane steam reforming in autothermal packed‐bed membrane reformer

An autothermal membrane reformer comprising two separated compartments, a methane oxidation catalytic bed and a methane steam reforming bed, which hosts hydrogen separation membranes, is optimized for hydrogen production by steam reforming of methane to power a polymer electrolyte membrane fuel cell (PEMFC) stack. Capitalizing on recent experimental demonstrations of hydrogen production in such a reactor, we develop here an appropriate model, validate it with experimental data and then use it for the hydrogen generation optimization in terms of the reformer efficiency and power output. The optimized reformer, with adequate hydrogen separation area, optimized exothermic‐to‐endothermic feed ratio and reduced heat losses, is shown to be capable to fuel kW‐range PEMFC stacks, with a methane‐to‐hydrogen conversion efficiency of up to 0.8. This is expected to provide an overall methane‐to‐electric power efficiency of a combined reformer‐fuel cell unit of ～0.5. Recycling of steam reforming effluent to the oxidation bed for combustion of unreacted and unseparated compounds is expected to provide an additional efficiency gain. © 2010 American Institute of Chemical Engineers AIChE J, 2011     

Performance Research on a Methane Compact Reformer Integrated with Catalytic Combustion

A multichannel reformer integrated with catalytic combustion was investigated for methane steam reforming to produce hydrogen. In this system, the main portion of the required heat was supplied by methane oxidation in the catalytic combustor located on two sides of the reformer. In the compact multichannel reactor, the methane conversion rate is high enough compared to the equilibrium values at different temperatures. The performance of the multichannel reformer was investigated under various operating conditions, such as the reformer temperature and the feed stream ratios in both the reformer and the catalytic combustor. The best feed flow rate ratio of reforming to combustion ranged from 1.3 to 1.5, with > 95 % methane conversion. It is anticipated that this multichannel reformer can generate enough hydrogen for a 30‐W fuel cell system, due to its small volume.     

Simulation of autothermal reforming in a staged‐separation membrane reactor for pure hydrogen production

Steam methane reforming with oxygen input is simulated in staged‐separation membrane reactors. The configuration retains the advantage of regular membrane reactors for achieving super‐equilibrium conversion, but reaction and membrane separation are carried out in two separate units. Equilibrium is assumed in the models given the excess of catalyst. The optimal pure hydrogen yield is obtained with 55% of the total membrane area allocated to the first of two modules. The performance of the process with pure oxygen input is only marginally better than with air. Oxygen must be added in split mode to reach autothermal operation for both reformer modules, and the oxygen input to each module depends on the process conditions. The effects of temperature, steam‐to‐carbon ratio and pressure of the reformer and the area of the membrane modules are investigated for various conditions. Compared with a traditional reformer with an ex situ membrane purifier downstream, the staged reactor is capable of much better pure hydrogen yield for the same autothermal reforming operating conditions.     

Analysis of hydrogen production from methane autothermal reformer with a dual catalyst-bed configuration

This paper presents a performance analysis of a dual-bed autothermal reformer for hydrogen production from methane using a non-isothermal, one dimensional reactor model. The first section of Pt/Al₂O₃ catalyst is designed for oxidation reaction, whereas the second one based on Ni/MgAl₂O₄ catalyst involves steam reforming reaction. The simulation results show that the dual-bed autothermal reactor provides higher reactor temperature and methane conversion compared with a conventional fixed-bed reformer. The H₂O/CH₄ and O₂/CH₄ feed ratios affect the methane conversion and the H₂/CO product ratio. The addition of steam at lower temperatures to the steam reforming section of the dual-bed reactor can produce the synthesis gas with a higher H₂/CO product ratio.     

Novel circulating fast fluidized-bed membrane reformer for efficient production of hydrogen from steam reforming of methane

The coupling of steam reforming and oxidative reforming of methane for the efficient production of hydrogen is investigated over Ni/Al₂O₃ catalyst in a novel circulating fast fluidized-bed membrane reformer (CFFBMR) using a rigorous mathematical model. The removal of product hydrogen using palladium hydrogen membranes “breaks” the thermodynamic equilibrium barrier exists among the reversible reactions. Oxygen can be introduced into the adiabatic CFFBMR for oxidative reforming by direct oxygen (or air) feed and through dense perovskite oxygen membranes. The simulations show that high productivity of hydrogen can be obtained in the CFFBMR. The combination of these two different processes does not only enhance the hydrogen productivity but also save the energy due to the exothermicity of the oxidative reforming. Based on the preliminary investigations, four parameters (number of hydrogen membranes, number of oxygen membranes, direct oxygen feed rate and steam-to-carbon feed ratio) are carefully chosen as main variables for the process optimization. The optimized result shows that the hydrogen productivity (moles of hydrogen produced per hour per m³ of reactor) in the novel CFFBMR is about 8.2 times higher than that in typical industrial fixed-bed steam reformers.     

Pure hydrogen generation in a fluidized bed membrane reactor: Application of the generalized comprehensive reactor model

A generalized comprehensive model was developed to simulate a wide variety of fluidized-bed catalytic reactors. The model characterizes multiple phases and regions (low-density phase, high-density phase, staged membranes, freeboard region) and allows for a seamless introduction of features and/or simplifications depending on the system of interest. The model is implemented here for a fluidized-bed membrane reactor generating hydrogen. A concomitant experimental program was performed to collect detailed experimental data in a pilot scale prototype reactor operated under steam methane reforming (SMR) and auto-thermal reforming (ATR) conditions, without and with membranes of different areas under diverse operating conditions. The results of this program were published in Mahecha-Botero et al. [2008a. Pure hydrogen generation in a fluidized bed membrane reactor: experimental findings. Chem. Eng. Sci. 63(10), pp. 2752-2762]. The reactor model is tested in this second paper of the series by comparing its simulation predictions against axially distributed concentration in the pilot reactor. This leads to a better understanding of phenomena along the reactor including: mass transfer, distributed selective removal of species, interphase cross-flow, flow regime variations, changes in volumetric flow, feed distribution, and fluidization hydrodynamics. The model does not use any adjustable parameters giving reasonably good predictions for the system of study.     

Production of synthesis gas

The state-of-the-art for the production of synthesis gas from the steam reforming of methane is reviewed and discussed. Particular attention is given to the design of the tubular reformer and carbon formation on the nickel catalyst. Improvements in syngas technology are discussed, including: CO₂ reforming, autothermal reforming and heat exchange reforming, and the energy efficiencies of direct and indirect methane conversion are compared and contrasted.     

Intensified energetically enhanced steam methane reforming through the use of membrane reactors

This work focuses on the implementation of membrane reactors (MRs) in the production of hydrogen through steam–methane reforming (SMR). A novel equilibrium MR model featuring Gibbs Free Energy Minimization is introduced and applied to the SMR-MR process. In addition, the concept of “energetically enhanced steam methane reforming (EER),” which allows for the use of a hybrid (methane combustion/renewable energy) energy supply in the production of hydrogen, is intensified. The UNISIM software (Honeywell™) is used to create a range of intensified flowsheets depicting the proposed IEER-MR process as well as two baseline flowsheets depicting “a standard SMR-MR process” and “a fully exothermic EER process.” Heat integration studies are carried out on the developed flowsheets, and the baseline designs are compared to the IEER-MR designs to identify energetic intensification.     

Advances on methane steam reforming to produce hydrogen through membrane reactors technology: A review

Methane steam reforming is the most common industrial process used for almost the 50% of the world’s hydrogen production. Commonly, this reaction is performed in fixed bed reactors and several stages are needed for separating hydrogen with the desired purity. The membrane reactors represent a valid alternative to the fixed bed reactors, by combining the reforming reaction for producing hydrogen and its separation in only one stage. This article deals with the recent progress on methane steam reforming reaction, giving a short overview on catalysts utilization as well as on the fundamentals of membrane reactors, also summarizing the relevant advancements in this field.     

Novel compact steam reformer for fuel cells with heat generation by catalytic combustion augmented by induction heating

The overall objective of the project is to investigate, design and test an improved steam reformer for fuel cell power plants.

Catalytic combustion is used to minimise the disadvantages of conventional external reforming. By integrating various technologies, smaller-scale reformer, lower emission levels and reduced start-up time along with improved temperature control can be achieved.

Catalytic combustion is used to generate the heat required for the reforming reaction, thus avoiding NO_x formation. The heat can be generated locally and made available for the reforming reaction using a thermally conductive substrate.

The first results of the catalytic test reactor show good conversion rates for both the combustion and the reforming reaction. Based on the hydrogen production rate, the initial objectives for the volume of the reformer have proven to be feasible.

The results are used to build a 20 kW integrated test reactor.     

化学链干重整联合制氢热力学分析及实验

提出了一种化学链甲烷干重整联合制氢工艺。该工艺由还原反应器、干重整反应器、蒸汽反应器和空气反应器组成，在实现制氢的同时获得可变H₂/CO比的合成气。借助ASPEN plus软件和小型流化床实验台，在等温条件下，温度900℃，采用Fe₂O₃/Al₂O₃载氧体，对该工艺进行热力学分析和实验验证。结果显示，当铁氧化物被还原至FeO/Fe时，干重整反应器内甲烷转化率可以达到98%，CO产率可以达到94%。干重整反应器中同时发生甲烷干重整和部分氧化反应，载氧体内部晶格氧可以有效降低积炭并提高合成气H₂/CO比。积炭发生于晶格氧消耗殆尽时。积炭进入蒸汽反应器，发生气化反应，降低氢气纯度。     

Theoretical investigation of aromatics production enhancement in thermal coupling of naphtha reforming and hydrodealkylation of toluene

In the current research, an exothermic reaction is proposed to be coupled with naphtha reforming reactions. Hydrodealkylation (HDA) of toluene, which is a well-known petrochemical reaction, is discussed and is suggested as a potential exothermic reaction to be coupled with the endothermic naphtha reforming reactions. The first, the second, and the third reactor of the conventional naphtha reforming process have been substituted in three different cases by thermally coupled reactors and optimized parameters of the final case have been investigated. Considering lower operational costs due to the elimination of inter stage heaters, investigation of thermally coupled reactors has been the first priority of this research. The investigation shows that substitution of the first two reactors and, in the final case, all conventional reactors by the new configuration can improve the production yield of the aromatics by 14% and 21%, respectively compared with conventional naphtha reforming process. The final case has been optimized as well, and 45% and 11% improvement in aromatics and hydrogen production has been observed.     

Modeling of synthesis gas and hydrogen production in a thermally coupling of steam and tri-reforming of methane with membranes

In this novel study, tri-reforming process was used as a heat source to proceed steam reforming of methane in a two membrane hydrogen perm-selective Pd/Ag thermally coupled reactor. Results illustrated that H₂/CO ratio at the output of steam and tri-reforming sides reached to 6.1 and 0.9, respectively. Additionally the results showed that methane conversion at the output of steam and tri-reforming sides reached to 31% and 96%, respectively. By increasing the feed flow rate of tri-reforming side from 28,120 to 140,600 kmol h⁻¹, methane conversion and H₂ molar flow rate enhanced 40% and 28.64%, respectively.     

A hybrid adsorbent-membrane reactor (HAMR) system for hydrogen production

Design characteristics and performance of a novel reactor system, termed a hybrid adsorbent-membrane reactor (HAMR), have been investigated for hydrogen production. The recently proposed HAMR concept couples reactions and membrane separation steps with adsorption on the membrane feed-side or permeate-side. Performance of conventional reactors has been significantly improved by this integrated system. In this paper, an HAMR system has been studied involving a hybrid-type packed-bed catalytic membrane reactor undergoing methane steam reforming through a porous ceramic membrane with a CO₂ adsorption system. This HAMR system is of potential interest to pure hydrogen production for fuel cells for various mobile and stationary applications. Reactor behaviors have been investigated for a range of temperature and pressure conditions. The HAMR system shows enhanced methane conversion, hydrogen yield, and product purity, and provides good promise for reducing the hostile operating conditions of conventional reformers, and for meeting the product purity requirements.     

Sorbent-enhanced/membrane-assisted steam-methane reforming

Thermodynamic equilibrium and kinetic reactor models are used to simulate a fluidized bed membrane reactor with in situ or ex situ hydrogen and/or CO₂ removal for production of pure hydrogen by steam methane reforming. In the equilibrium model, the membranes and CO₂ removal are located in separate vessels downstream of the reformer. As the recycle ratio increases, the overall performance approaches that where membranes are located inside the reactor. Whether located in situ or ex situ, hydrogen removal by membranes and CO₂ capture by sorbents both enhance hydrogen production. In the kinetic reactor model, a circulating fluidized bed membrane reformer is coupled with a catalyst/sorbent regenerator. Sorbent enhancement combined with membranes could provide very high hydrogen yields. In addition, since carbonation is exothermic, with its heat of reaction similar in magnitude to the endothermic heat of reaction of the net reforming reactions, sorbent enhancement can provide much of the heat needed in the reformer. The overall heat needed for the process would then be provided in a separate calciner, acting as a sorbent regenerator. While the technology is promising, several practical issues need to be examined.     

Optimal design of a thermally coupled fluidised bed heat exchanger reactor for hydrogen production and octane improvement in the catalytic naphtha reformers

The present study combines simultaneously the definition of fluidisation and process intensification (thermally coupled heat exchanger reactor) concept and determines the optimum operational conditions in both sides of the reactor, using Differential Evolution (DE) optimisation approach. The exothermic hydrogenation of nitrobenzene to aniline takes place in a set of tubular reactors which is placed inside the naphtha reactors and thermally handle the endothermic reaction of reforming. A single objective function consists of four terms including aromatic mole fraction of the reformate and hydrogen production from each reactor in the endothermic side as well as the total molar flow rate of aniline and nitrobenzene conversion in the exothermic side is defined. Seven decision variables such as inlet temperature of exothermic and endothermic sides, exothermic molar flow rates for the first and the second reactors and the number of tubes are considered during the optimisation procedure. Temperature constraints have been considered in both sides during the optimisation in order to reduce the possibility of rapid catalyst deactivation by sintering. Results show approximately 464.4 and 598.9 kg/h increase in aromatic and aniline production rates in optimised thermally coupled fluidised bed naphtha reactor (OTCFBNR) compared with non‐optimised case (TCFBNR), respectively. Such a theoretical study is necessary prior to designing new pilot plants and revamping industrial units. © 2011 Canadian Society for Chemical Engineering     

核能制氢与高温气冷堆

氢是环境友好的能源载体,利用核能制氢引起了广泛的研究兴趣。本文对核能制氢的工艺,包括甲烷蒸气重整、高温电解和热化学循环进行了综述;提出了制氢过程对反应堆的要求,并介绍了高温气冷堆用于核能制氢的优势。     

Development of a Combined Plasma-Matrix Reformer for Solid Oxide Fuel Cell Application

A novel plasma-matrix reformer (PMR) was suggested for methane conversion into hydrogen-rich fuel. To demonstrate the possibility of reforming performance, characteristics of product gas and CH₄ conversion were identified according to O₂/C ratio, water vapor supply, reformed gas recirculation, and water feed in the recirculation gas affecting energy conversion and hydrogen production. When the reformed gas recirculation and water feed to the recirculation pipe were performed at the same time, hydrogen production and energy conversion efficiency were superior compared to the conventional reforming method. The optimal operating conditions of the PMR were determined. The obtained high energy conversion efficiency and hydrogen selectivity indicated the applicability to solid oxide fuel cell stacks for residential power generation.     

Highly active and stable Rh/MgOAl2O3 catalysts for methane steam reforming

Highly active and coke-resistant Rh catalysts were developed for methane steam reforming in microchannel chemical reactors. Rh loading was optimized on a stable MgOAl₂O₃ support to improve the volumetric productivity for methane conversion. Catalyst activities were stable over a wide range of steam/carbon ratios. In particular, experimental results demonstrated that Rh/MgOAl₂O₃ catalysts are extremely active for methane steam reforming and are resistant to coke formation at stoichiometric steam/carbon ratio of 1 for over 14 h time-on-stream with no sign of deactivation. Methane steam reforming activities on this catalyst is compared in both a microchannel reactor and a conventional micro-tubular reactor. Significant performance enhancement was observed in microchannel reactors owing to improved heat and mass transfer.