Design requirements for medium-sized wind turbines for remote and hybrid power systems

This paper provides an overview of the design requirements for medium-sized wind turbines intended for use in a remote hybrid power system. The recommendations are based on first-hand experience acquired at the University of Massachusetts through the installation, operation, and upgrade of a 250-kW turbine on a mountain top with difficult access in Western Massachusetts. Experience with the operation of this turbine and the design of its control system, together with a long history in the design and analysis of hybrid power systems, has made it possible to extend the work in Western Massachusetts to remote or hybrid power systems in general. The University test site has many attributes of more remote sites and the overall wind turbine installation is typical of one that could power a hybrid wind system. For example, access to the site is limited due to steep terrain, snow, and environmental restrictions. Also, the power lines feeding the turbine exhibit voltage sags and phase imbalance, especially during start-up. This paper is based on the experience gained from the operation of this wind turbine and assesses the requirements for the design and operation of medium to large wind turbines in remote locations. The work summarizes lessons learned relative to: (1) sensors, communication, and control capabilities; (2) grid connection issues; and (3) weather-related problems. The final section of the paper focuses on design requirements to ensure successful installation and the completion of maintenance and repairs at remote sites.     

建筑密度对建筑物群内风能利用的影响

针对建筑物群内风能应用问题,采用CFD方法,对建筑密度分别为26%、20%、18%、16%、14%的5种建筑物群周围风速和湍流强度特征开展研究,分析建筑密度对建筑物群内风力机合理安装位置的影响方式。结果表明：在低于1.5H高度范围内,建筑物群的建筑密度越大,同一安装高度上适合于安装风力机的区域就越大,即越有利于建筑物群内风能的应用;在高度高于1.5H后,建筑密度对建筑物群内风力机安装位置的影响消失;无论建筑密度大小,在低于1.2H的高度范围内,建筑物群内不适合安装风力机;在高度高于1.45H后,可优先考虑将风力机安装于建筑物群内中间一排建筑物顶面,在建筑物顶面可优先将风力机安装于拐角位置;5种建筑密度的建筑物群内只考虑风速要求即可确定风力机的合理安装位置。     

Performance and viability analysis of small wind turbines in the European Union

Nowadays, wind energy plays a key role as a sustainable source of energy and wind turbines are a relevant source of power for many countries world-wide. In such a context, this paper investigates the technical and economic feasibility of small wind turbines for five of the main European Union countries (France, Germany, Italy, Spain and The Netherlands). Ten commercial turbines with rated power from 2.5 kW to 200 kW are evaluated considering their installation and operative conditions. Several parameters most affecting wind turbine performances are evaluated and the estimation of the annual cash flows during the expected plant life-time are determined as a function of both the installation location (wind speed probability distribution, national incentive scheme and tax level) and the wind turbine characteristics (rated power curve, maintenance, installation and shipping costs). The obtained data are presented and discussed through a parametric analysis based on the Net Present Value capital budget approach, showing the conditions making these systems profitable or non-profitable and explaining the relative motivations. Moreover, the analysis outcomes are further investigated highlighting the dependence of the turbine profitability from the considered parameters, including a comparative analysis among the five analyzed European countries.     

Estimation of wind energy production in various sites in Australia for different wind turbine classes: A comparative technical and economic assessment

This study examines the effect of different wind turbine classes on the electricity production of wind farms in three areas of Australia, which present low, low to medium, and medium to high wind potential: Gingin, Armidale, and Gold Coast Seaway. Wind turbine classes determine the suitability of installing a wind turbine in a particulate site. Wind turbine data from six different manufacturers have been used. For each manufacturer, at lest two wind turbines with identical rated power (in the range of 1.5 MW–3 MW) and different wind turbine classes (IEC I, IEC II and/or IEC III) are compared. The results show the superiority of wind turbines that are designed for lower wind speeds (higher IEC class) in all three locations, in terms of energy production. This improvement is higher for the locations with lower and medium wind potential (Gingin and Armidale), and varies from 5% to 55%. Moreover, this study investigates the economical feasibility of a 30 MW wind farm, for all combinations of site locations and wind turbine models.     

New high profitable wind turbines

To generate more quantities of electric energy from wind it is necessary to use a new type of wind turbine built in the regulable mantle's nozzle. This wind turbine type replaces the free air stream from wind by a programmed, i.e. regulated, and partially concentrated stream of air. The nozzle shell is designed as an aerodynamically shaped ring with wings with its lower pressure side pointed towards the centre so that the lift force on each part of the wing is directed radially towards the centre. This induces centrifugal reaction force in the airflow that causes the stream field to expand strongly downstream of the rotor and includes a greater number of streamlines in the active stream in front of the rotor (upstream). Thus the nozzle forces a higher mass flow rate of air through the turbine. The higher mass flow and higher velocity reduction behind the rotor result in a higher energy output from the wind turbine in the nozzle. In this way the wind turbine efficiency is multiplied. New turbines induce more power from weaker and medium winds and their lasting time, because of the relation P=f(v³) (i.e. the power corresponds to wind velocity raised to third power). Wind turbine nozzle produces three times more energy than conventional wind turbine. Short economic analysis for conditions of the island of Lastovo indicates that profit gained by new turbines is up to five times higher than by conventional turbines. The new wind turbine nozzle should generate interest and demand on an international market, even for regions with weaker winds.     

Feasibility study of harnessing wind energy for turbine installation in province of Yazd in Iran

This paper analyses the wind speed of some major cities in province of Yazd which is located in central part of Iran. Also, the feasibility study of implementing wind turbines to take advantage of wind power is reviewed and then the subject of wind speed and wind potential at different stations is considered. This paper utilized wind speed data over a period of almost 13 years between 1992 and 2005 from 11 stations, to assess the wind power potential at these sites. In this paper, the hourly measured wind speed data at 10 m, 20 m and 40 m height for Yazd province have been statically analyzed to determine the potential of wind power generation. Extrapolation of the 10 m data, using the Power Law, has been used to determine the wind data at heights of 20 m and 40 m. The results showed that most of the stations have annual average wind speed of less than 4.5 m/s which is considered as unacceptable for installation of the wind turbines. City of Herat has higher wind energy potential with annual wind speed average of 5.05 m/s and 6.86 m/s, respectively, at height of 10 m and 40 m above ground level (AGL). This site is a good candidate for remote area wind energy applications. But some more information is required, because the collected data for Herat is only for 2004. Cities of Aghda with 3.96 m/s, Gariz with 3.95 m/s, and Maybod with 3.83 m/s annual wind speed average at height of 10 m above ground level are also able to harness wind by installing small wind turbines. The Tabas and Bafgh sites wind speed data indicated that the two sites have lower annual wind speed averages between 1.56 m/s and 2.22 m/s at 10 m height. The monthly and annual wind speeds at different heights have been studied to ensure optimum selection of wind turbine installation for different stations in Yazd.     

Assessment of the wind power potential at SANAE IV base, Antarctica: a technical and economic feasibility study

This paper presents a study for the utilization of wind energy at the South African research station, SANAE IV, in Antarctica (71°40’ S 2° 50’ W). A procedure to evaluate the feasibility of utilising wind power for Antarctic stations is given. The analysis is based on the technical and economic aspects of installing and operating a wind turbine at remote locations. Special attention has been given to conditions encountered at Antarctica, like site accessibility, low temperatures, icing and snow, long transportation distances and environmental issues. The aspect of externalities is incorporated into the economic analysis. The Northern Power Systems NW100/19 wind turbine is found to be the best-suited wind turbine for use at SANAE IV, given the harsh climatic conditions, like frequent windstorms and extreme temperatures. The wind turbine features a yearly energy output of 430 MWh with a capacity factor of 0.49, at a mean wind speed of 10.8 m/s. The study shows that a wind turbine installation at SANAE IV is an attractive solution to reduce fuel consumption and therefore emissions of the diesel electric generators considerably. The use of a wind turbine at SANAE IV could lead to a savings in externalities of about R110 000, -per annum.     

Performance and safety of rooftop wind turbines: Use of CFD to gain insight into inflow conditions

The installation of small and medium-size wind turbines on the rooftops of high buildings has been often suggested by architects and project developers as a potential solution for achieving sustainable energy in building design. In such locations, however, because of the presence of buildings and other adjacent obstructions, wind is normally turbulent, unstable and weak, in terms of direction and speed. The use of wind turbines in the built environment poses challenges to overcome, including energy yield reduction due to lower mean wind speeds in urban areas, and environmental impacts because of their close vicinity to people and property.There is a need to understand the inflow wind conditions for a small wind turbine in the built-environment. A resource assessment of the potential wind turbine site in the built environment can determine the wind characteristics including zones of wind acceleration, recirculation, blocking and channelling. This knowledge is crucial for input into the design process of a small wind turbine to accurately predict blade fatigue loads and ensure that it operates safely, and performs optimally in the environment.Computational Fluid Dynamics (CFD) is a useful method to model wind flows in order to perform a resource assessment for the application of small wind turbines in a manner that requires less time and investment than a measurement campaign. This paper presents the results of research using a CFD code to model wind flows over the roof of a building and assesses the possibility of combining a CFD package with wind atlas software to form a wind energy resource assessment tool for the application of small wind turbines on the roof of a building. Experimentation with the model shows that the results are particularly sensitive to building height and shape, roof shape, wind direction, and turbine installation height and location. The results will be used to help develop a recommended practice of wind resource assessment in the built environment, in an international collaborative effort via the International Energy Agency Task 27.     

Optimal placement of wind turbines in a wind park using Monte Carlo simulation

In the present study, a novel procedure is introduced for the optimal placement and arrangement of wind turbines in a wind park. In this approach a statistical and mathematical method is used, which is called ‘Monte Carlo simulation method’. The optimization is made by the mean of maximum energy production and minimum cost installation criteria. As a test case, a square site is subdivided into 100 square cells that can be possible turbine locations and as a result, the program presents us the optimal arrangement of the wind turbines in the wind park, based on the Monte Carlo simulation method. The results of this study are compared to the results of previous studies that handle the same issue.     

Technical potential of on-site wind powered hydrogen producing refuelling stations in the Netherlands

This study assesses the technical potential of wind turbines to be installed next to existing fuelling stations in order to produce hydrogen. Hydrogen will be used for Fuel Cell Vehicle refuelling and feed-in existing local gas grids. The suitable fuelling stations are selected through a GIS assessment applying buffer zones and taking into account risks associated with wind turbine installation next to built-up areas, critical infrastructures and ecological networks. It was found that 4.6% of existing fuelling stations are suitable. Further, a hydrogen production potential assessment was made using weather station datasets, land cover data and was expressed as potential future Fuel Cell Electric Vehicle demand coverage. It was found that for a 30% FCEV drivetrain scenario, these stations can produce 2.3% of this demand. Finally, a case study was made for the proximity of those stations in existing gas distribution grids.     

Wind energy development and its environmental impact: A review

Wind energy, commonly recognized to be a clean and environmentally friendly renewable energy resource that can reduce our dependency on fossil fuels, has developed rapidly in recent years. Its mature technology and comparatively low cost make it promising as an important primary energy source in the future. However, there are potential environmental impacts due to the installation and operation of the wind turbines that cannot be ignored. This paper aims to provide an overview of world wind energy scenarios, the current status of wind turbine development, development trends of offshore wind farms, and the environmental and climatic impact of wind farms. The wake effect of wind turbines and modeling studies regarding this effect are also reviewed.     

Design and implementation of wind energy system in Saudi Arabia

This paper introduces an accurate procedure to choose the best site from many sites and suitable wind turbines for these sites depending on the minimum price of kWh generated (Energy Cost Figure (ECF)) from wind energy system. In this paper a new proposed computer program has been introduced to perform all the calculations and optimization required to accurately design the wind energy system and matching between sites and wind turbines. Some of cost calculations of energy methods have been introduced and compared to choose the most suitable method. The data for five sites in Saudi Arabia and hundred wind turbines have been used to choose the best site and the optimum wind turbine for each site. These sites are Yanbo, Dhahran, Dhulom, Riyadh, and Qaisumah. One hundred wind turbines have been used to choose the best one for each site. This program is built in a generic form which allows it to be used with unlimited number of sites and wind turbines in all over the world. The program is written by using Visual Fortran and it is verified with simple calculation in Excel. The paper showed that the best site is Dhahran and the suitable wind turbine for this site is KMW-ERNO with 5.85 Cents/kWh. The worst site to install wind energy system is Riyadh with minimum price of kWh of 12.81 Cents/kWh in case of using GE Energy 2 wind turbine.     

Evaluation of hydrogen production by wind energy for agricultural and industrial sectors

Wind power potential by itself is not a good indicator of the suitability of a region for wind power generation for different purposes. Economic attractiveness is a better indicator in this regard as it stimulates the involvement of private businesses in this sector. Naturally, the shorter is the payback period or the time required to reach profitability, the more attractive will be the project. Considering the high wind energy potential of some regions of Iran, this study evaluates the wind energy available for generating electricity as well as hydrogen by industrial and agricultural sectors in four cities of Ardebil province, namely Ardebil, Khalkhal, Namin, and Meshkinshahr, and then conducts an econometric analysis accordingly. Wind power potentials are evaluated using the energy pattern factor and Weibull distribution function based on 5-year meteorological data of the studied regions. Economic evaluations are performed based on the present worth of incomes and costs, which are estimated for two models of wind turbines with 3.5 and 100 KW rated power. Results indicate that the cities of Namin and Ardebil with wind power densities of respectively 261.68 and 258.99 W/m² have the best condition. The economic analysis conducted for turbines shows that for Ardebil, installation of the 3.5 KW and 100 KW turbines will have a payback period of 13 and 5 years, respectively. For Khalkhal, Namin, and Meshkinshahr, the only feasible option is installation of the 100 KW turbine, which would result in a payback period of respectively 10.2, 6.1 and 8.7 years. Then it is investigated how much hydrogen can be gained if these private sectors invest in producing hydrogen using nominated wind turbines.     

Can road traffic mask sound from wind turbines? Response to wind turbine sound at different levels of road traffic sound

Wind turbines are favoured in the switch-over to renewable energy. Suitable sites for further developments could be difficult to find as the sound emitted from the rotor blades calls for a sufficient distance to residents to avoid negative effects. The aim of this study was to explore if road traffic sound could mask wind turbine sound or, in contrast, increases annoyance due to wind turbine noise. Annoyance of road traffic and wind turbine noise was measured in the WINDFARMperception survey in the Netherlands in 2007 (n=725) and related to calculated levels of sound. The presence of road traffic sound did not in general decrease annoyance with wind turbine noise, except when levels of wind turbine sound were moderate (35–40 dB(A) Lden) and road traffic sound level exceeded that level with at least 20 dB(A). Annoyance with both noises was intercorrelated but this correlation was probably due to the influence of individual factors. Furthermore, visibility and attitude towards wind turbines were significantly related to noise annoyance of modern wind turbines. The results can be used for the selection of suitable sites, possibly favouring already noise exposed areas if wind turbine sound levels are sufficiently low.     

Research on a power quality monitoring technique for individual wind turbines

The extensive deployment of megawatt-scale wind turbines is bringing more challenges to the safety and stability of electric grid than ever before. This is not only because of the unstable wind over time but the increased risk of power quality pollution by defective wind turbines particularly when the turbines today are still experiencing various reliability issues. To prevent the power quality pollution by defective turbines, a new power quality monitoring technique dedicated for individual wind turbines is developed in this paper, so that the quality of the power generated by an individual turbine can be monitored by the wind turbine condition monitoring system. Through simulated and physical experiments on a specially designed test rig, some encouraging results have been achieved. It has been shown that the proposed technique is not only valid for monitoring the power quality of an individual wind turbine, but helpful in detecting the mechanical and electrical faults occurring in the wind turbines.     

建筑外形对建筑顶面风力机微观选址的影响

针对城市建筑环境内的风能应用问题,利用CFD方法对4种不同建筑外形的高层建筑物顶面风场湍流特征进行研究,开展建筑外形对风向变化的敏感性分析,并分析4种建筑物顶面风速、湍流强度随高度的变化规律,确定4种建筑外形的建筑顶面风力机的合理安装位置和高度,结果表明：具有圆润曲线外形的2类建筑更利于风力机的安装,风力机的安装高度可更低;建筑物的长轴和短轴越接近,顶面越有利于风力机的安装;4种建筑外形的建筑顶面安装风力机时仅考虑U/U₀≥1的有利安装高度H_u即可保证风力机的有效输出功率和运行安全;无盛行风向情况下,4种建筑物的中心区域更有利于风力机安装,风力机的安装高度最低,圆柱体、椭圆体、正方体及长方体建筑物顶面中心区域风力机最低安装高度分别为1.05H、1.09H、1.11H及1.14H。     

On the energy output estimation of wind turbines

During the operation of the German test field for small Wind Energy Conversion Systems (WECS) on the island of Pellworm five wind turbines were tested following recommendations of the International Energy Agency (IEA) expert group. Possible errors in the estimation of a tested wind turbine's total energy output at a potential installation site are investigated. Different wind speed frequency distributions (the measured one, the Rayleigh and the two-parameter Weibull distribution) are used to calculate the total energy output. The differences between the various distributions are mostly below 10 per cent. An improvement of the energy output estimate by a Weibull-instead of a Rayleigh distribution was not found. It is also shown that the use of the recommended 10 min averages or any other average overestimates the WECS' efficiency, up to 14 per cent on average depending on turbulence intensity. Wind power instead of wind speed is the appropriate parameter for power performance testing. Spectra of wind power and electrical power output show three areas of different correlation. A resistance length for wind turbines is shown to be dependent on the WECS operation status.     

A multicriteria approach to evaluate wind energy plants on an Italian island

The decision-making process regarding the choice of alternative energy is multidimensional, made up of a number of aspects at different levels—economic, technical, environmental, and social. In this respect multicriteria analysis appears to be the most appropriate tool to understand all the different perspectives involved and to support those concerned with the decision making process by creating a set of relationships between the various alternatives. The main aim of this paper is to make a preliminary assessment regarding the feasibility of installing some wind energy turbines in a site on the island of Salina (Aeolian islands—Italy). Thus, a multicriteria method will be applied in order to support the selection and evaluation of one or more of the solutions proposed. Having analysed the local environmental conditions and its energy profile, four wind turbine configurations were postulated as options. These options were then appraised by comparison against a family of criteria and calculations were performed using a multicriteria algorithm to rank the solutions, from the best to worst. The option at the top of the ranking refers to the installation of a plant of 150 kW and this emerged as the right compromise between the costs of realization, local energy requirements and the need to conserve the area and the environment especially in view of the high/medium-bracket tourism business on the island. The sensitivity analysis performed subsequently backed up the findings. As this work demonstrates, multicriteria analysis can provide a valid tool to aid decision making for achieving targets relating to more sustainable green energy.     

Analysis of a pumped storage system to increase the penetration level of renewable energy in isolated power systems. Gran Canaria: A case study

A significant number of islands have been forced to restrict the penetration level of renewable energy sources (RES) in their conventional electrical power systems. These limitations attempt to prevent problems that might affect the stability and security of the electrical system. Restrictions that may apply to the penetration of wind energy can also be an obstacle when meeting European Union renewable energy objectives. As a partial solution to the problem, this paper proposes the installation of a properly managed, wind-powered, pumped hydro energy storage system (PHES) on the island of Gran Canaria (Canary Islands). Results from a dynamic model of the island’s power system show that the installation of a pumped storage system is fully supported in all circumstances. They also show that the level of wind penetration in the network can be increased. These results have been obtained assuming that two of the largest existing reservoirs on the island (with a difference in altitude of 281 m and a capacity of aprox. 5,000,000 m³ each) are used as storage reservoirs with three 54 MW generators. Likewise, the ability of such facilities to contribute to the stability of the system is shown. This type of installation can reduce fossil fuel consumption, reducing CO₂ emissions. Moreover, not only can the PHES improve wind penetration level, but it also allows the number of wind farms installed to be increased. Regions with geographically suitable sites and energy problems similar to those on the Canary Islands are encouraged to analyze the technical and economic feasibility of installing similar power systems to the one in this paper. Such systems have an enormous, unexplored potential within the general guiding framework of policies promoting clean, renewable energy.     

Aggregated dynamic model for wind farms with doubly fed induction generator wind turbines

As a result of increasing wind farms penetration in power systems, the wind farms begin to influence power system, and thus the modelling of wind farms has become an interesting research topic. Nowadays, doubly fed induction generator based on wind turbine is the most widely used technology for wind farms due to its main advantages such as high-energy efficiency and controllability, and improved power quality. When the impact of a wind farm on power systems is studied, the behavior of the wind farm at the point common coupling to grid can be represented by an equivalent model derived from the aggregation of wind turbines into an equivalent wind turbine, instead of the complete model including the modelling of all the wind turbines. In this paper, a new equivalent model of wind farms with doubly fed induction generator wind turbines is proposed to represent the collective response of the wind farm by one single equivalent wind turbine, even although the aggregated wind turbines operate receiving different incoming winds. The effectiveness of the equivalent model to represent the collective response of the wind farm is demonstrated by comparing the simulation results of equivalent and complete models both during normal operation and grid disturbances.