聚乳酸/聚乙烯醇纳米纤维的制备及结构

以二甲基亚砜为溶剂,制备不同配比的聚乳酸(PLLA)和聚乙烯醇(PVA)的混合溶液,静电纺丝制得PLLA/PVA纳米纤维。采用红外光谱仪、原子力显微镜等对PLLA/PVA纳米纤维结构与性能进行了表征。结果表明:PLLA/PVA纳米纤维中PVA上的羟基与PLLA上的羰基形成了氢键,PLLA与PVA之间存在一定的相互作用,但PLLA/PVA纳米纤维存在相分离现象;混合溶液的PLLA质量分数为11%,PVA质量分数为8%时可以得到较好的PLLA/PVA纳米纤维,但PVA质量分数为6%时出现液滴及珠丝,PVA质量分数为4%时,不能制得纳米纤维。     

小麦蛋白/聚乙烯醇复合纳米纤维的制备及其表征

以小麦蛋白、聚乙烯醇(PVA)为原料,采用静电纺丝法制备小麦蛋白/PVA共混复合纳米纤维,重点研究纺丝液质量分数、电压、接收距离对纤维形态的影响,利用扫描电镜、傅里叶变换红外光谱、X-射线衍射光谱对纤维的形态与结构进行表征。结果表明:在纺丝液质量分数10%、小麦蛋白与PVA质量比8∶2、电压12 kV、接收距离10 cm的条件下,可以制备平均直径为280 nm左右的均一、表面光滑的纳米纤维。小麦蛋白与PVA复合后,分子间以氢键结合。     

PVA/Au纳米复合纤维的制备及表征

以聚乙烯醇(PVA)为还原剂和保护剂,采用PVA还原氯金酸(HAuCl4)制备纳米金(Au),一步法制备PVA/Au溶液,通过静电纺丝制备了PVA/Au纳米复合纤维.利用紫外可见光谱仪、透明电镜和扫描电镜对PVA/Au纳米复合纤维进行了表征.结果表明:随着HAuCl4浓度的增加,Au纳米粒子的粒径逐渐增大;HAuCl4...     

静电纺丝法制备聚碳酸酯基聚氨酯纳米纤维的研究

以N,N-二甲基甲酰胺(DMF)和四氢呋喃(THF)为混合溶剂配制聚碳酸酯基热塑性聚氨酯(PU)纺丝溶液,通过静电纺丝法制备PU纳米纤维。重点研究了纺丝溶液浓度、混合溶剂中DMF和THF的体积比、纺丝电压和纺丝溶液流速对PU纳米纤维形态、直径及其分散性的影响。结果发现,纺丝液浓度为12%,混合溶剂中DMF与THF体积比为1∶1,纺丝电压为10 kV,纺丝溶液流速为0. 8 m L/h时,通过静电纺丝法制得的PU纳米纤维粗细均匀,表面光滑,纤维之间无粘连现象,形成的纳米纤维膜空隙率高。     

水性硝化纤维/聚乙烯醇复合乳液的制备与性能

将水性硝化纤维(WNC)乳液与聚乙烯醇(PVA)溶液共混制备了WNC/PVA复合乳液。用傅里叶变换红外光谱(FT-IR)和透射电镜(TEM)表征了材料的相容性,并通过万能材料试验机、吸水率测试和热重分析等方法研究了PVA含量对复合材料力学性能、耐水性和热性能的影响。实验结果表明:WNC与PVA之间存在分子间氢键作用,两者相容性较好。当PVA含量为15%时,复合乳液具有优异的稳定性,涂膜拉伸强度为4.0 MPa,断裂伸长率为299.0%,吸水率为18.4%。     

静电纺丝法制备聚乙烯醇纳米纤维膜及其交联处理

用化学方法和物理方法对聚乙烯醇(PVA)纳米纤维膜进行交联处理,并且用SEM、DSC和XRD分别对不同的纳米纤维膜样品进行表征。结果表明:煅烧处理的PVA纳米纤维膜的结晶度提高,抗溶解性能良好。     

静电纺丝制备复合纳米纤维方法的研究进展

近年来,复合纳米纤维因其具有优异的特性而引起国内外广泛关注.简要阐述了静电纺丝制备纯纳米纤维的方法,重点综述了静电纺丝构建复合纳米纤维方法的研究进展。     

光致变色PVA/PEI纳米纤维膜制备及性能

针对传统光致变色纤维膜受酸碱等外界影响易导致变色效率低,以及稳定性不高的问题,提出在传统静电纺丝制备PVA/PEI纳米纤维膜的基础上,负载光致变色纳米微球,然后与戊二醛交联,得到性能稳定的光致变色纤维膜,并考察了PVA/PEI质量比、戊二醛交联以及光致变色纳米微球含量对光致变色纤维膜性能的影响。结果表明：在PVA/PEI的质量比为75∶25,光致变色微球的含量为10%时,经过戊二醛交联的光致变色纤维膜表面光滑,串珠连续且均匀;随着紫外光照的增加,纤维膜的颜色逐步加深,但当光致变色微球的含量大于10%时,颜色不再发生变化;将光致变色纤维膜浸水24h,纤维膜仍保持连续且均匀的多孔纤维结构。根据以上试验看出,纤维膜材料可用于环境领域中,以达到美化环境的目的。     

再生丝素蛋白/聚乙烯醇共混纳米纤维的静电纺丝研究

以静电纺丝方法制备再生丝素蛋白/聚乙烯醇共混纳米纤维。研究了共混配比、溶液浓度、添加剂含量及电纺电压、喷丝距离等因素对纤维成形及纤维有关性能的影响。研究表明:与聚乙烯醇共混后再生丝素纤维的柔韧性有一定改善,适当增加PVA在共混物中的含量、提高纺丝液浓度以及纺丝电压有利于改善共混溶液的可纺性。另外,加入丙三醇虽可使纤维直径的均匀性有所提高,但却不利于纤维成形。     

聚乳酸/肉桂醛复合纳米纤维膜的制备及表征

采用水溶液饱和法制备了肉桂醛/β环糊精包合物,将其添加到聚乳酸（PLA）溶液中,利用静电纺丝技术制备PLA/肉桂醛复合纳米纤维膜。利用扫描电子显微镜(SEM)探讨了静电纺丝条件对PLA纳米纤维膜纤维直径及表面形貌的影响,通过傅里叶变换红外光谱(FTIR)对PLA/肉桂醛复合纳米纤维膜做了特征官能团分析,并对其热力学性能、力学性能及抗菌性能进行了表征。结果表明,制备的PLA/肉桂醛复合纳米纤维膜纤维形态良好,平均直径为175 nm,FT IR研究显示肉桂醛与PLA之间属于物理混合。该复合纳米纤维膜热分解温度265.52 ℃,拉伸强度为2.45 MPa,对大肠杆菌、金黄色葡萄球菌和枯草芽孢杆菌都具有抑菌性,其中对金黄色葡萄球菌的抑菌性最强。     

Electrospinning fabrication and characterization of poly(vinyl alcohol)/waterborne polyurethane nanofiber membranes in aqueous solution

Poly(vinyl alcohol) (PVA)/waterborne polyurethane (WBPU) nanofiber mats were prepared using electrospinning method with aqueous solutions. Scanning electron microscopy (SEM), X‐ray diffraction (XRD), thermal gravimetric analyzer (TGA), and tensile strength testing machine (ZWICK) were used to characterize the morphology and properties of the PVA/WBPU nanofiber mats. The results showed that the morphologies of PVA/WBPU nanofiber mats changed with the total solid concentration and the mass ratio of PVA/WBPU in the spinning solution. The tensile strength and thermal stability of the fibers could be significantly affected by the WBPU contents. The electrospun PVA/WBPU membranes showed higher water uptake, which would have potential applications in wound dressings. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

聚乙烯醇降解酶发酵过程模拟

应用Matlab软件对聚乙烯醇降解酶发酵过程数学模型进行最优参数估计和非线性曲线拟合,得到了假单胞菌Pseudomonas sp XT11-Z90S发酵生产聚乙烯醇(PVA)降解酶的菌体生长、底物PVA消耗和聚乙烯醇降解酶合成的数学模型.结果表明,模型计算值和实验结果非常接近,其平均相对误差绝大部分小于10％,说明所建数学模型能较好地对聚乙烯醇降解酶发酵过程进行模拟.     

细菌纤维素/聚乙烯醇复合材料的制备及性能

采用浸渍法向细菌纤维素(BC)中引入聚乙烯醇(PVA),对BC/PVA复合材料的结构、光学性能及力学性能进行研究。当浸渍液中PVA浓度为20 g/L时,力学性能及光学性能测试表明,复合材料在保持BC超高力学强度的同时光学性能较纯BC显著提高,透光率最高可达90.74%,可见光区最多提高24.26%。扫描电子显微镜及X射线衍射表明,大量自由PVA渗入BC网络结构,复合材料层状结构淡化,结晶度下降。     

Electrospinning fabrication and characterization of poly(vinyl alcohol)/montmorillonite nanofiber mats

Poly(vinyl alcohol) (PVA)/montmorillonite clay (MMT) nanofiber mats have been fabricated by the electrospinning technique. The PVA/MMT nanofiber mats were characterized by X‐ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), Fourier transform infrared (FTIR), and mechanical measurements. The study showed that the introduction of MMT results in improvement in tensile strength, and thermal stability of the PVA matrix. XRD patterns and SEM micrographs suggest the coexistence of exfoliated MMT layers over the studied MMT contents. FTIR revealed that there might be possible interaction occurred between the MMT clay and PVA matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

添加不同物质的聚乙烯醇/海藻酸钠静电纺丝研究

分别添加少量NaCl、乙酸、表面活性剂十二烷基硫酸钠(SDS),研究少量添加物对海藻酸钠/聚乙烯醇(PVA)溶液性质和静电纺纤维的影响,并初步探讨了溶液静电纺丝机制。结果表明:NaCl改变了溶液的电导率和黏度,乙酸降低了溶液的黏度、提高了溶剂挥发性,SDS降低了溶液的表面张力;适量的添加物可使纤维形貌得到改善;添加物对电纺纤维化学结构无本质影响;无机盐离子加剧了纤维拉伸作用,结晶性有所提高;处于泰勒锥处液滴表面受到静电排斥力、表面张力、同种聚合物分子间的氢键作用力、不同聚合物分子间的氢键作用力以及聚合物同水等溶剂形成的氢键作用力。     

Mechanical and Dynamic Analysis of Poly (Vinyl Alcohol)-Modified Inorganic Filler Composite

A study of polymer-acid-modified Red mud composite (PRC) was done using a polymer matrix of poly (vinyl alcohol) (PVA) and layered Red mud as reinforcing agent. Composite materials were prepared by effectively dispersing the PVA matrix into the inorganic layered modified Red mud via a conventional solvent-casting technique. The PRC materials, as synthesized, were typically characterized by Fourier-Transformation infrared (FTIR) spectroscopy. The nature of the PRC films was investigated by means of X-ray diffraction. The dispersion of modified filler in the polymer matrix was investigated by TEM analysis. To study the temperature dependencies of the dynamic modulii, stress relaxation, mechanical loss, and damping phenomena of the composite material, dynamic mechanical analysis (DMA) was done. The tensile behavior of the composite films was analyzed by comparing their tensile strength and their modulus of elasticity with change in filler content.     

Preparation and characterization of graphene oxide/poly(vinyl alcohol) composite nanofibers via electrospinning

Graphene oxide (GO) was well dispersed in poly(vinyl alcohol) (PVA) diluted aqueous solution, and then the mixture was electrospun into GO/PVA composite nanofibers. Electron microscopy and Raman spectroscopy on the as‐prepared and calcined samples confirm the uniform distribution of GO sheets in the nanofibers. The thermal and mechanical properties of the nanofibers vary considerably with different GO filler contents. The decomposition temperatures of the GO/PVA composite nanofiber dropped by 38–50°C compared with pure PVA. A very small loading of 0.02 wt % GO increases the tensile strength of the nanofibers by 42 times. A porous 3D structure was realized by postcalcining nanofibers in H₂. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Studies On The Crosslinking Of Poly (Vinyl Alcohol)

This paper is concerned with the cross-linking of poly(vinyl alcohol) (PVA) using maleic acid as the cross-linker. The curative (maleic acid) dose and the curing temperature and time were varied between 2.5 and 60% (w/w), 120 and 160 °C and 30 and 120 min, respectively. From a thorough swelling study in both hot and cold water (percentage swelling, gel content, swelling ratio, etc-) the optimum curative dose and curing conditions have been evaluated. The molecular weight between the cross-links exhibited a sharp fall up to a maleic acid dose of 20% (w/w). A comparative evaluation of maleic acid cross-linked and heat-treated PVA films has been done. Better heat stability for maleic acid cross-linked PVA was observed from thermogravimetric analysis. A shift in glass transition temperature was observed for both heat-treated and maleic acid treated PVA compared with the virgin one. IR spectroscopic study indicated the presence of an ester linkage and an olefinic double bond in maleic acid treated and heat-treated PVA films, respectively. Maleic acid cross-linked PVA is quite stable in different polar and nonpolar solvents. A definite structural pattern has been observed in maleic acid cross-linked PVA films through scanning electron microscopy.