淬火温度对添加B_4C的ASP30粉末冶金高速钢组织及力学性能的影响

采用粉末冶金方法制备添加B_4C的全致密ASP30高速钢,样品在1 040℃到1 200℃范围内淬火,并且经过560℃三次回火,研究淬火温度对其力学性能及显微组织的影响。采用扫描电子显微镜、洛氏硬度计和材料力学性能测试机研究高速钢的组织和力学性能。结果表明:添加质量分数为0.025%B_4C的ASP30粉末冶金高速钢在1 160℃下烧结2 h后会形成月牙形液相碳化物,从而获得全致密的烧结组织。随淬火温度升高,显微组织中碳化物的数量明显减少,基体中合金元素固溶含量提高,基体晶粒长大,断口形貌呈准解理断裂但断口平整度下降。随淬火温度升高,钢的硬度提高,最高值达到69 HRC。抗弯强度、断裂韧性均下降,抗弯强度最高值达4 357MPa,断裂韧性最高值为48.6 MPa/m1/2。冲击韧性先升高后下降,在1 080℃最高为18.85 J/cm2。     

包套热挤压M32粉末冶金高速钢的组织性能研究

提出了一种解决粉末冶金高速钢制备工艺繁琐、性价比低等问题的包套热挤压工艺,采用该工艺制备了M32粉末冶金高速钢,研究了不同挤压温度和热处理对M32粉末高速钢的显微组织与性能的影响。结果表明:未热处理时,随挤压温度的升高,试样相对密度及硬度变化趋势一致,均是先升高后降低,在挤压温度为1 240℃时达到峰值,分别为98.04%和45.6HRC;在淬火温度1 180℃以及回火温度560℃热处理后,M32高速钢的晶粒及碳化物颗粒尺寸较小且分布均匀,力学性能最佳,其抗弯强度及硬度分别为3 721.8 MPa和66.7HRC。     

冷处理及回火次数对刀剪用M390粉末钢组织和性能的影响

通过对M390粉末不锈钢进行淬火、冷处理和低温回火，研究了热处理对合金显微组织和力学性能的影响。结果表明：冷处理降低合金中残余奥氏体的数量，大幅度提高材料硬度和抗弯强度；1 180℃淬火试样冷处理后，随回火次数的增加，单位面积碳化物颗粒总数和平均粒径增加，硬度下降，一次回火后硬度达到61.1 HRC;1 130℃淬火试样冷处理后，随着回火次数增加，单位面积颗粒总数不断增加，平均粒径和硬度下降，一次回火后硬度达到60.0 HRC；淬火温度和回火次数对抗弯强度影响不大，合金抗弯强度为4 000 MPa左右。     

热处理工艺对30MnSi PC钢棒耐延迟断裂性能的影响

对30MnSi PC钢棒进行了淬火回火处理,分析探讨了热处理工艺对高强度钢耐延迟断裂性能的影响.采用FIP试验作为PC钢棒耐延迟断裂性能的评价方法.研究发现,相同的回火工艺下30MnSi钢的耐延迟断裂性能随淬火温度的升高呈先升高后降低的趋势,950 ℃左右淬火其耐延迟断裂性能较好;在保证强度满足要求的前提下提高回火温度可以提高钢的耐延迟断裂性能.组织观察发现,经430 ℃左右回火后,30MnSi钢棒得到的回火索(屈)氏体组织均匀细小,碳化物弥散分布在马氏体板条界上,耐延迟断裂性能较好.可见,通过改变热处理制度改变组织形态,是改善30MnSi钢的耐延迟断裂性能的一种有效途径.     

405不锈钢高温组织转变研究

通过热膨胀法以及Thermo-Calc热力学计算软件对SA240-405不锈钢铁素体向奥氏体转变的温度进行了测量和计算。进一步结合淬火与回火热处理,分析了405不锈钢在高温下组织随温度与时间的变化关系。研究结果表明,405不锈钢铁素体向奥氏体开始转变的温度为795~832℃,转变终了温度为910~925℃。温度高于1 050℃,随温度升高,奥氏体逐渐向铁素体转变,淬火后的马氏体含量降低。在950及980℃淬火,得到的组织为马氏体与铁素体的双相组织,淬火时间为30~60 min得到的硬度较高;进一步延长淬火时间,硬度逐渐降低。在730℃回火后得到的组织为铁素体与回火马氏体,无明显残余奥氏体,回火后组织的硬度随时间延长逐渐降低。     

回火温度对高氮轴承钢碳化物演变及硬度的影响

对高氮马氏体不锈轴承钢进行直接淬火并重复2次深冷及不同温度的回火处理,采用光学显微镜、SEM电镜,TEM电镜和洛氏硬度计等,研究了不同回火温度下碳化物的演变规律与硬度变化的相关性,在不同回火温度下根据硬度出现先下降后上升再下降变化的趋势,对各回火温度下碳化物的尺寸区间分布频数、单位面积数量、平均尺寸及碳化物所占单位面积比进行了表征及分析,结果表明:随回火温度由150升高到500℃,碳化物的尺寸随回火温度的升高从0.39长大至0.62μm,碳化物为近球形M23C6型。150~300℃回火时硬度下降与基体脱溶有关;300~450℃回火时碳化物单位面积数量及所占面积分数都增加;回火至500℃时,细小碳化物聚集长大单位面积数量减少,碳化物所占面积分数减少。由此得出回火时硬度变化与析出碳化物的单位数量和其面积分数有关。     

热处理工艺对海洋工程用高强度耐低温H型钢组织及性能影响

摘要：以热轧耐低温H型钢为研究对象,采用光学显微镜、扫描电镜、透射电镜分析和力学性能测试等手段,研究了完全淬火和亚温淬火对试验钢微观组织和力学性能的演变规律。结果表明,试验型钢经780℃亚温淬火+600℃回火处理后,形成回火索氏体+铁素体的网状组织;试验型钢900℃淬火+600℃回火处理后,转变得到具有马氏体位向的回火索氏体,碳化物分布更加细小均匀,位错密度下降。2种热处理工艺制备H型钢综合力学性能优良,屈服强度均达到500MPa以上,900℃淬火+600℃回火处理后钢的屈服强度和抗拉强度更高。-40℃低温冲击韧性比热轧状态下出现大幅度提高,随着淬火温度升高冲击功更加稳定。     

回火温度对1500MPa级直接淬火钢组织与性能的影响

设计了一种新型1500MPa级Si-Mn-Cr-Ni-Mo多组元系低合金、超高强度工程结构钢,研究了回火温度对直接淬火钢组织与力学性能的影响.结果表明,抗拉强度随回火温度的升高而不断降低,屈服强度随回火温度升高先升高后下降,延伸率和冲击功均随回火温度升高呈现先升高、后降低、再升高的变化趋势.分析认为,回火过程组织演变的物理机制一方面包括板条马氏体和位错亚结构的回复、再结晶软化过程,另一方面包括残余奥氏体的分解与马氏体中过饱和碳的脱溶及析出第2相的强化机制综合作用.250℃回火后,板条马氏体内析出ε碳化物;400℃回火后ε碳化物明显粗化,产生回火脆性;600℃回火后部分析出相在奥氏体中形核,在马氏体基体内长大和粗化,最终形态为近似球形,另一部分析出相在马氏体内形核、生长,呈现椭球形或矩形.     

喷射成形2060高速钢的组织与性能

利用雾化沉积炉制备喷射成形2060高速钢沉积坯,经过锻造后再进行盐浴淬火和回火处理,研究喷射成形2060高速钢及其热处理后的组织与力学性能。结果表明:喷射成形2060高速钢沉积坯的表面较光洁,无明显的宏观偏析,晶粒较细小,晶粒尺寸约为20μm,沉积坯的相对密度在99.5%以上;沉积坯中主要存在M6C和MC两种碳化物相,均匀弥散分布在晶界与晶内以及基体中,氧含量只有1.6×10-7左右。2060高速钢的抗弯强度随淬火温度升高而逐渐降低,淬火温度应低于1 210℃。在1 170~1 190℃下淬火时可获得抗弯强度≥3 000MPa、硬度≥70 HRC的良好综合力学性能。     

HYW3高速钢热处理工艺与性能研究

对HYW3高速钢选择了1 110～1 200℃不同淬火温度,530℃、550℃、570℃不同回火温度的正交热处理工艺试验,测定了各工艺制度下试样的抗弯强度、无缺口冲击韧性、淬火硬度、晶粒度、淬回火硬度等参数,对试验结果进行了分析,选择了适合的热处理工艺。     

转炉炉壳热应力分析

根据实际转炉建立实体模型。以有限元为手段,考虑了炉衬和炉壳材料的物性参数随温度变化的特点和炉衬与炉壳之间膨胀间隙,计算了转炉炉壳在温度载荷和炉衬膨胀压力同时作用下的热应力。所得结果可为转炉炉壳设计提供依据。     

Results of treatment of cancer of the cardia

Cancer of the cardia is traditionally discussed with cardiac cancer of the lower portion of the esophagus and upper gastric cancer invading the esophagus, and the specific characteristics of cancer of the cardia have never been clearly defined. We reviewed the outcome of 172 patients with adenocarcinoma of the cardia who had undergone radical surgery between 1949 and 1994 in the Division of Gastrointestinal Surgery of the Cancer Institute Hospital. The centers of the tumors were located within 2 cm above and below the boundary between the esophagus and the stomach, and their longitudinal diameter was less than 8 cm. We divided the patients into an early period (1949-1979; n = 79) and a late period (1980-1994; n = 93), and focused on the historical transition. There were no differences in patient gender or histology between the two periods. However, the late period was associated with fewer cases of esophageal invasion and shorter longitudinal diameter, as the age of the population advanced. The number of advanced cancers such as the localized and infiltrative type had decreased, and early cancer and early clinical stage had become more common, but despite the fact that the number of early cancers had increased, extended dissection, such as thoracic and paraaortic lymph node dissection, was performed more frequently. By clinical stage, the long-term outcome markedly improved in Stage I patient in the late period, and tended to improve in Stage II and III patients. This appears to have been attributable to the prevention of micrometastasis by extended dissection, although the number of early cancers is another major potential cause. There were no differences in the outcome of Stage IV patients between the two periods, and further advances in multimodality therapy must be awaited. The range of resection is basically proximal gastrectomy, and if there are adequate indications, the prognosis is favorable. In view of the status of lymphatic flow and lymph node metastasis, and long-term results, lateroaortic lymph node dissection is important. Since the number of early cancer patients has been increasing, if intraabdominal recurrence is prevented, intrathoracic lymph node dissection will contribute greatly to the outcome of such patients.     

焦炭热性能指标意义浅析

通过对焦炭在高炉内的历程及其变化规律的剖析,阐述焦炭热性能指标的意义,形象地把焦炭在高炉内的损耗分为三部分(M1,M2,M3)。指出M2对焦比及焦炭价格有一定的指导作用。     

Effect of antibiotics of chemotaxis of human leukocytes

The effect of 20 different antibiotics on chemotaxis by human neutrophils was studied. Human leukocytes incubated with chloramphenicol, rifampin, sodium fusidate, and tetracyclines in vitro showed markedly depressed migration. The mechanisms by which these antibiotics affect leukotaxis are discussed.     

Quality of life of relatives of mental patients

Usage of quality of life of psychiatric patients' relatives as the parameter of estimation of the quality of psychiatric care is considered. By means of standard questionnaire elaborated by the authors as well as by means of both individual and group conversations the quality of life was analyzed in 40 relatives which lived together with psychiatric patients. Different spheres of their life and difficulties (financial, social-psychologic, production) were examined in families with such patients. The defects of psychiatric care that had direct influence on the quality of life of the psychiatric patients' relatives are outlined.     

The effect of amount of possession of the trait of hostility on accuracy of perception of hostility in others.

Some theories of personality hold that an individual's perception of others is influenced by his own personality characteristics; more specifically, that a trait of low social value will be projected more into others, and that insight into the possession of these characteristics reduces this distortion. These 2 hypotheses were tested by having a group of college students rate each other (including themselves) on degree of friendliness or hostility. Agreement with group rating about self yielded the insight score. In general, the hypotheses were supported; the "friendly" Ss were most accurate in their perception of others, and insight was positively associated with accurate perception. From Psyc Abstracts 36:04:4HL16M. (PsycINFO Database Record (c) 2010 APA, all rights reserved)