Temperature dependence of the optical properties of Hg1−xCdxTe

The alloy composition of Hg_1−xCd_xTe should be controlled during growth, so that the desired band gap and the lattice-matched layer may be obtained. In-situ spectroscopic ellipsometry, now commercially available, enables one to acquire spectral data during growth. If one knows the optical dielectric function as a function of alloy composition and temperature, the technique can be fully used to monitor and control temperature, the thickness, and the alloy composition. For this purpose, we first obtained temperature dependent spectral data of Hg_1−xCd_xTe by spectroscopic ellipsometry (SE). The spectral data of Hg_1−xCd_xTe with x = 1,0.235, and 0.344 were obtained from room temperature to 800Kin the photon energy range from 1.3 to 6 eV. The spectral data revealed distinctive critical point structures at E₀, E₀+Δ₀, E₁, E₁+Δ₁, E₂(X), and E₂(Σ). Critical point energies decreased and linewidths increased monotonically as temperature increased. The model for the optical dielectric function enabled (i) the critical point parameters to be determined accurately, and (ii) the spectral data to be expressed as a function of temperature within and outside the experimental range.     

Critical thickness in the HgCdTe/CdZnTe system

We present an analysis of the critical thickness of Hg_1−xCd_xTe on Cd_1−yZn_yTe substrates as a function of x and y and show that a very tight control of the substrate composition is needed to produce dislocation-free epi-layers. Hg_1−xCd_xTe layers on relaxed underlayers of different compositions of Hg are also examined.     

Defect reduction in Hg1−xCdxTe grown by molecular beam epitaxy on Cd0.96Zn0.04Te(211)B

A study on preparation of Cd_0.96Zn_0.04Te(211)B substrates for growth of Hg_1−xCd_xTe epitaxial layers by molecular beam epitaxy (MBE) was investigated. The objective was to investigate the impact of starting substrate surface quality on surface defects such as voids and hillocks commonly observed on MBE Hg_1−xCd_xTe layers. The results of this study indicate that, when the Cd_0.96Zn_0.04Te(211)B substrates are properly prepared, surface defects on the resulting MBE Hg_1−xCd_xTe films are reduced to minimum (size, ∼0.1 m and density ∼500/cm²) so that these MBE Hg_1−xCd_x Te films have surface quality as good as that of liquid phase epitaxial (LPE) Hg_1−xCd_xTe films currently in production in this laboratory.     

Real-time control of HgCdTe growth by organometallic vapor phase epitaxy using spectroscopic ellipsometry

The use of spectroscopic ellipsometry for monitoring the vapor phase epitaxial growth of mercury cadmium telluride (Hg_1−xCd_xTe) in real-time is demonstrated. The ellipsometer is used to perform system identification of the chemical vapor deposition reactor used for the growth of CdTe and to measure the response of the reactor to different growth conditions. The dynamic behavior of the reactor is also studied by evaluating the gas transport delay. The optical constants of Hg_1−xCd_xTe are determined at the growth temperature for different compositions.In-situ real-time composition control is performed during the growth of Hg_1−xCd_xTe. The required target compositions are attained by the ellipsometer and appropriate corrections are also made by the controller when a noise input in the form of a temperature variation is introduced.     

Transient behavior of Hg1−xCdxTe films deposited on (100) CdTe substrates by chemical vapor transport

The growth history of Hg_1−xCd_xTe films deposited on (100) CdTe substrates by chemical vapor transport (CVT) has been studied, for the first time, by using a transient growth technique. The observed morphological evolution of Hg_1−xCd_xTe films deposited at 545°C shows a transition behavior from three-dimensional (3D) islands to two-dimensional (2D) layer growth. The experimental results indicate that the so-called critical time needed for the above morphological transition is about lh under present experimental conditions. Based on the chemical bonding properties of Hg_1−xCd_xTe, and on the behavior of the morphological transition, the Stranski-Krastanov growth mode is suggested for the epitaxial growth system. The time dependence of the growth thickness, of the growth rate (R₁₀₀) along the [100] direction, and of the surface composition all reveal a transient behavior. These are related to the nature of the Hg_1-xCd_xTe/ (100)CdTe heterojunction and to the surface reactions. Comparison of the growth rates and of the total mass deposited as a function of time shows the relationship between epitaxial growth and mass flux of the Hg_1−xCd_xTe-HgI₂ chemical vapor transport system.     

Transient behavior of Hg1−xCdxTe film growth on 3° off-(100) CdTe substrates by chemical vapor transport

The effects of substrate misorientation on Hg_1−xCd_xTe films, deposited on 3° off-(100) CdTe substrates by chemical vapor transport (CVT), have been studied for the first time using a transient growth technique. The morphological evolution of Hg_1−xCd_xTe films deposited on the vicinal CdTe substrates at 545°C shows a transition from three-dimensional islands to two-dimensional layer growth. The time and thickness required for the above morphological transition is about 0.75 h and 7 μm, respectively, under present experimental conditions. The pronounced long-range-terrace surface morphology of the Hg_1−xCd_xTe films illustrates the strong effects of the misorientation of the CdTe substrates and of the growth kinetics on the CVT growth of this hetero-epitaxial system. The transient behavior of the surface morphology, of the surface composition, and of the growth rate all reveal the influences of the 3° misorientation of the (100) CdTe substrates on the Hg_1−xCd_xTe epitaxy. The experimental mass flux results of the Hg_1−xCd_xTe-HgI₂ CVT system under transient and steady-state conditions can be related to the surface kinetics and to the thermodynamic properties of the system. The combined results show that the interface kinetics are not fixed in the transient regime and that they are coupled to the vapor mass transport.     

Structure investigation on Hg1−xCdxTe liquid phase epitaxial films grown by the meltetch technique

Hg_1−xCd_xTe films were grown by a modified meltetch liquid phase epitaxial (LPE) technique which includes both substrate and epilayer etchback steps. The crystal quality of epilayer has been investigated by means of transmission electron microscopy, scanning electron microscopy, and double crystal x-ray diffraction. It has been found that adequate meltetch of the substrate at the beginning of LPE provides a fresh and flat surface for epitaxial growth, while epilayer meltetch at the end of LPE may prevent spurious melt sticking.     

An improved method for Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te surface chemistry characterization

Hg_1−xCd_xTe surface chemistry has been studied extensively with well-known tools such as electron spectroscopy for chemical analysis (ESCA) and Auger electron spectroscopy (AES) in order to advance detector array operability, performance, and yield. Raytheon Vision Systems has pioneered the first application of time-of-flight secondary ion mass spectrometry (TOF-SIMS) as a Hg_1−xCd_xTe surface diagnostic tool to provide unprecedented analysis capability, including analyzing a 0.5-μm-diameter spot, high mass resolution, elemental and molecular composition scrutiny, applicability to insulators, and surface film sensitivity in the part per million range. In this study, data are presented illustrating surface chemistry geometry effects and photoresist redeposition due to common Hg_1−xCd_xTe processing steps including photolithography, bromine etching, and photoresist stripping.     

Spectroscopic ellipsometry for monitoring and control of molecular beam epitaxially grown HgCdTe heterostructures

A systematic study of the effect of measurement perturbation on in situ monitoring of the composition of molecular beam epitaxially (MBE) grown Hg_1−xCd_xTe using spectroscopic ellipsometry was carried out. Of the five variables investigated, which included angle of incidence, wavelength of the light beam, modulator rotation, analyzer rotation, and modulator amplitude, the angle of incidence and the modulator rotation had the strongest effect on the in situ Hg_1−xCd_xTe composition monitoring process. A wobble-free sample manipulator was installed to reduce the impact of these two variables. With these improvements, the spectroscopic ellipsometer is now routinely used to monitor Hg _1−xCd_xTe compositions during MBE growth of heterostructures and is a useful tool in diagnosing growth-related problems. Examples are included for both application areas, that include the control of the interface between Hg_1−xCd_xTe layers of different compositions, i.e. device engineering.     

Growth method,composition, and defect structure dependence of mercury diffusion in CdxHg1–xTe

Mercury radiotracer diffusion results are presented, in the range 254 to 452°C, for bulk and epitaxial Cd_xHg_1–xTe, and we believe this to be the first report for metalorganic vapor phase epitaxy (MOVPE) grown Cd_xHg_1–xTe. For all growth types studied, with compositions of x_Cd=0.2±0.04, the variation of the lattice diffusion coefficient, D_Hg, with temperature, under saturated mercury partial pressure, obeyed the equation: D_Hg=3×10⁻³ exp(−1.2 eV/kT) cm² s⁻¹. It was found to have a strong composition dependence but was insensitive to changes of substrate material or crystal orientation. Autoradiography was used to show that mercury also exploited defect structure to diffuse rapidly from the surface. Dislocation diffusion analysis is used to model defect tails in MOVPE Cd_xHg_1–xTe profiles.     

Effects of a-Si:H resist vacuum-lithography processing on HgCdTe

A vacuum-compatible process for carrying out lithography on Hg_1−xCd_xTe and CdTe films was previously demonstrated. It was shown that hydrogenated amorphous silicon (a-Si:H) could be used as a dry resist by projecting a pattern onto its surface using excimer laser irradiation and then developing that pattern by hydrogen plasma etching. Pattern transfer to an underlying Hg_1−xCd_xTe film was then carried out via Ar/H₂ plasma etching in an electron cyclotron resonance (ECR) reactor. Despite the successful demonstration of pattern transfer, the possibility of inducing harmful effects in the Hg_1−xCd_xTe film due to this vacuum lithography procedure had not been explored. Here we present structural and surface compositional analyses of Hg_1−xCd_xTe films at key stages of the a-Si:H vacuum lithography procedure. X-ray diffraction double crystal rocking curves taken before and after a-Si:H deposition and after development etching were identical, indicating that bulk structural changes in the Hg_1−xCd_xTe film are not induced by these processes. Cross-section transmission electron microscopy studies show that laser-induced heating in the 350 nm thick a-Si:H overlayer is not sufficient to cause structural damage in the underlying Hg_1−xCd_xTe surface. In vacuo surface analysis via Auger electron spectroscopy and ion scattering spectroscopy suggest that the hydrogen plasma development process produces Hg-deficient surfaces but does not introduce C contamination. However, after ECR plasma etching into the Hg_1−xCd_xTe film, the measured x value is much closer to that of the bulk.     

Observation of phase separation in Hg1−xCdxTe solid solutions by low incident angle x-ray diffraction

The low incident angle (surface analysis) and the conventional wide angle (bulk analysis) x-ray diffraction techniques were employed to investigate the existence of a miscibility gap in the Hg_1−xCd_xTe system. Samples of initial composition Hg_0.46Cd_0.54Te were annealed at 140 and 400°C, respectively, for four weeks. The diffraction planes (531) and (642) have been selected for the x-ray diffraction analysis. The results of this work provide the first, direct experimental evidence for the existence of a miscibility gap at lower temperature in the Hg_1−xCd_xTe system. The phase separation occurs primarily in a thin surface layer at 140°C and is reversible after annealing at 530°C. The compositions of the two compounds at the tie-line at 140°C are Hg_0.22Cd_0.78Te and Hg_0.63Cd_0.37Te.     

Automated compositional control of Hg1−xCdxTe during MBE, using in situ spectroscopic ellipsometry

The implementation of a feedback control system for maintaining a desired compositional value in Hg_1−xCd_xTe epilayers is reported. An 88-wavelength ellipsometer monitored the Cd content (x) of a Hg_1−xCd_xTe film during molecular beam epitaxy, and deviations from a pre-determined set-point were automatically corrected via adjustments in the CdTe effusion cell temperature. The accuracy of this system (Δx∼0.002) was confirmed by Fourier transform infrared transmission measurements made ex situ on the epilayers.     

HgCdZnTe quaternary materials for lattice-matched two-color detectors

As the number of bands and the complexity of HgCdTe multicolor structures increases, it is desirable to minimize the lattice mismatch at growth interfaces within the device structure in order to reduce or eliminate mismatch dislocations at these interfaces and potential threading dislocations that can degrade device performance. To achieve this we are investigating the use of Hg_1−x−yCd_xZn_yTe quaternary alloys which have an independently tunable lattice constant and bandgap. Lattice matching in Hg_1−x−yCd_xZn_yTe structures can be achieved using small additions of Zn (y<0.015) to HgCdTe ternary alloys. We have investigated some of the basic properties of Hg_1−x−yCd_xZn_yTe materials with x≈0.31 and 0≤y≤0.015. The quaternary layers were grown on (112)CdZnTe substrates using MBE and the amount of Zn in the layers was determined from calibrated SIMS measurements. As expected, the lattice constant decreased and the bandgap increased as Zn was added to HgCdTe to form Hg_1−x−yCd_xZn_yTe. Hall-effect results for both n-type (In) and p-type (As) Hg_1−x−yCd_xZn_yTe layers were very similar to HgCdTe control samples. We have also utilized x-ray rocking curve measurements with (246) asymmetric reflections as a novel sensitive technique to determine the correct amount of Zn needed to achieve lattice matching at an interface. MWIR/LWIR n-p-n two-color triple-layer heterojunction structures were grown to evaluate the effects of minimizing the lattice mismatch between the widest bandgap p-type collector layer, using Hg_1−x−yCd_xZn_yTe, and the HgCdTe MWIR and LWIR collector layers and compared to structures that did not incorporate the quaternary. Sequential mode two-color detectors were fabricated using a 256 × 256, 30 μm unit cell design. There were several interesting findings. Macro defects predominantly affected the LWIR band (Band 2) operability and had little effect on the MWIR band (Band 1). The incorporation of Hg_1−x−yCd_xZn_yTe p-type collector layers had little effect on MWIR detector performance, but overall the LWIR performance was generally better. These initial detector results indicate that the use of Hg_1−x−yCd_xZn_yTe alloys in multicolor detector structures are potentially promising and should be pursued further.     

Physico-chemical properties of Ga and In dopants during liquid phase epitaxy of CdxHg1−xTe

This work deals with the study by means of radioactive tracers and autoradiography, as well as measuring of galvanomagnetic properties, of Ga and In doping of epitaxial Cd_xHg_1−xTe layers during their crystallization from a Te-rich melt. Ga and In were introduced in the form of Ga⁷² and In¹¹⁴ master alloys with Te. The effective distribution coefficients of Ga and In during the crystallization of the Cd_xHg_1−xTe solid solutions with x=0.20 to 0.23 were determined by cooling the Te-base melt to 515–470°C. Depending on the concentration of the dopants and the time-temperature conditions of Cd_xHg_1−xTe growth, these ratios for Ga and In were 1.5–2.0 and 1.0–1.5, respectively. The electrical activity of Ga and In was determined after annealing of the Cd_xHg_1−xTe layers in saturated Hg vapor at 270–300°C. In doping of the epitaxial layers to (3–8)×10¹⁴ cm⁻³ with subsequent annealing in saturated Hg vapor at ∼270°C increases the carrier lifetime approximately by a factor of two as compared with the undoped material annealed under the same conditions.     

Experimental determination of tie-lines in the Hg-Cd-Te system

Starting with powdered Hg_1−xCd_xTe, several tie-lines at 500 and 560°C were established using an energy dispersive spectrometer on a scanning electron microscope for the quantitative analysis. After holding at 500 or 560°C for time periods based upon the powder size and the published interdiffusion constant, then water quenching to room temperature, the primary grains were found to be uniform in composition and covered with a 5-6 μ layer of HgTe or low x Hg_1−xCd_xTe. The primary grain and overall compositions establish directions for tie-lines that are in good agreement with published experimental and theoreti-cal results.     

Electrical properties and compositional distributions of CVT and PVT grown Hg1−xCdxTe epilayers

Epitaxial layers of Hg_1−xCd_x Te were grown on CdTe substrates by the chemical vapor transport technique using Hgl₂ as a transport agent. The epilayers were of nearly uniform composition both laterally and to a depth of about one-half of the layer thickness. By comparison, the composition varied continuously throughout the depth of the layer for epilayers grown by the physical vapor transport technique. Layers were grown both p- and n-type with carrier concentrations on the order of 10¹⁷ cm⁻³. Low-temperature annealing was used to convert the p-type layers into n-type. The room-temperature carrier mobilities of as-grown and converted n-type layers ranged from 10³ to 10⁴ cm²/V-s depending on the composition and are comparable to previous literature values for undoped Hg_1−xCd_xTe crystals.     

Origin of void defects in Hg1−xCdxTe grown by molecular beam epitaxy

Characterization of defects in Hg_1−xCd_xTe compound semiconductor is essential to reduce intrinsic and the growth-induced extended defects which adversely affect the performance of devices fabricated in this material system. It is shown here that particulates at the substrate surface act as sites where void defects nucleate during Hg_1−xCd_xTe epitaxial growth by molecular beam epitaxy. In this study, we have investigated the effect of substrate surface preparation on formation of void defects and established a one-to-one correlation. A wafer cleaning procedure was developed to reduce the density of such defects to values below 200 cm⁻². Focal plane arrays fabricated on low void density materials grown using this new substrate etching and cleaning procedure were found to have pixel operability above 98.0%.     

Molecular beam epitaxial growth of HgCdTe on CdZnTe(311)B

A series of n-type, indium-doped Hg_1−xCd_xTe (x∼0.225) layers were grown on Cd_0.96Zn_0.04Te(311)B substrates by molecular beam epitaxy (MBE). The Cd_0.96Zn_0.04Te(311)B substrates (2 cm × 3 cm) were prepared in this laboratory by the horizontal Bridgman method using double-zone-refined 6N source materials. The Hg_1−xCd_xTe(311)B epitaxial films were examined by optical microscopy, defect etching, and Hall measurements. Preliminary results indicate that the n-type Hg_1−xCd_xTe(311)B and Hg_1−xCd_xTe(211)B films (x ∼ 0.225) grown by MBE have comparable morphological, structural, and electrical quality, with the best 77 K Hall mobility being 112,000 cm²/V·sec at carrier concentration of 1.9×10⁺¹⁵ cm⁻³.     

Characterization of a new planar process for implementation of p-on-n HgCdTe heterostructure infrared photodiodes

We report on a new, simple process to fabricate planar Hg_1−yCd_yTe/Hg_1−xCd_xTe (x<y) heterostructure photodiodes with p-on-n configuration. The material used for this demonstration was a double-layer p-on-n heterostructure that was grown by a liquid-phase-epitaxy technique. The p-on-n planar devices consisted of an arsenic-doped p-type epilayer (y=0.28) on top of a long-wavelength infrared n-type epilayer (x=0.225, =10 m). The ion-beam-milling p-type to n-type conversion effect was used to delineate the active device element, and to isolate the planar device. Detailed analysis of the current-voltage characteristics of these diodes as a function of temperature show that they have high performance, and that their dark current is diffusion-limited down to 60 K. The results show that over a wide range of cut-off wavelengths, the R₀A product values are close to the theoretical limit. Electro-optic properties of a 2-D array of small diodes with a 60- m pitch are presented, and demonstrate the potential of the new process for implementation of 2-D arrays. The electrical properties of the photodiodes are stable following long-term annealing at 80°C for 48 hours.