Reactively compatibilised polyamide6/ethylene-co-vinyl acetate blends: mechanical properties and morphology

Mechanical properties and morphological studies of compatibilised blends of PA6/EVA-g-MA and PA6/EVA/EVA-g-MA were studied as functions of maleic anhydride content (MA) and dispersed phase (EVA-g-MA) concentrations, respectively at blending composition of 20 wt% dispersed phase (EVA-g-MA or combination of EVA and EVA-g-MA). The maleic anhydride (MA) was varied from 1 to 6 wt% in the PA6/EVA-g-MA blend, whereas MA concentration was fixed at 2 wt% in the ternary compositions with varying level of EVA-g-MA. ATR-IR spectroscopy revealed the formation of in situ copolymer during reactive compatibilisation of PA6 and EVA-g-MA. It was found that notched Izod impact strength of PA6/EVA-g-MA blends increased significantly with MA content in EVA-g-MA. The brittle to tough transition temperature of reactively compatibilised blends was found to be at 23 °C. The impact fractured surface topology reveals extensive deformation in presence of EVA-g-MA whereas; uncompatibilised PA6/EVA blend shows dislodging of EVA domains from the matrix. Tensile strength of the PA6/EVA-g-MA blends increased significantly as compared to PA6/EVA blends. Analysis of the tensile data using predictive theories showed an enhanced interaction of the dispersed phase and the matrix. It is observed from the phase morphological analysis that the average domain size of the PA6/EVA-g-MA blends is found to decrease gradually with increase in MA content of EVA-g-MA. A similar decrease is also found to observe in PA6/EVA/EVA-g-MA blends with increase in EVA-g-MA content, which suggest the coalescence process is slower in presence of EVA-g-MA. An attempt has been made to correlate between impact strength and morphological parameters with regard to the compatibilised system over the uncompatibilised system.     

Compatibilization and properties of ethylene vinyl acetate copolymer (EVA) and thermoplastic polyurethane (TPU) blend based foam

Ethylene vinyl acetate copolymer/thermoplastic polyurethane (EVA/TPU) blending foams are rarely reported so far because of their poor compatibility, and addition of a compatibilizer to the blend system was our major interest, which can improve interfacial adhesion between the two phases. In this paper, TPU-grafted EVA (EVA-g-TPU), as a compatibilizer, was simply prepared using maleic anhydride-grafted EVA (EVA-g-MAH) and 4,4′ diamino diphenyl methane in the mixing process of TPU and EVA matrix. Fourier transform infrared spectroscopy and differential scanning calorimetry were used to investigate the structures of EVA-g-TPU and the interfacial reaction in the mixing process, and the effect of EVA-g-TPU on compatibilization between the two phases of EVA/TPU blends was investigated using scanning electron microscopy. Finally, EVA/EVA-g-TPU/TPU foams based on the good compatibility of the resin blends were prepared, and the physical properties directly related to the compatibility were investigated as a function of the theoretical quantity (molar mass) of EVA-g-TPU (n _EVA-g-TPU) in the foams. Moreover, the tensile strength, elongation at break, tear strength and compression set were improved by 19.0, 9.3, 43.6 and 7.5 %, respectively. Overall, EVA/EVA-g-TPU/TPU foams with excellent mechanical properties were obtained without sacrificing other important physical properties (lower density etc.) through popular and friendly means in this research.     

Miscibility,phase behavior,and mechanical properties of ternary blends of poly(vinyl chloride)/polystyrene/chlorinated polyethylene-graft-polystyrene

The effectiveness of chlorinated polyethylene-graft-polystyrene (CPE-g-PS) as a polymeric compatibilizer for immiscible poly(vinyl chloride)/polystyrene (PVC/PS) blends was investigated. The miscibility, phase behavior, and mechanical properties were studied using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), Izod impact tests, tensile tests, and scanning electron microscopy (SEM). DSC and DMA studies showed that PVC is immiscible with chlorinated polyethylene (CPE) in CPE-g-PS, whereas the PS homopolymer is miscible with PS in CPE-g-PS. The PVC/PS/CPE-g-PS ternary blends exhibit a three-phase structure: PVC phase, CPE phase, and PS phase that consisted of a PS homopolymer and PS in CPE-g-PS. The mechanical properties showed that CPE-g-PS interacts well with both PVC and PS and can be used as a polymeric compatibilizer for PVC/PS blends. CPE-g-PS can also be used as an impact modifier for both PVC and PS. SEM observations confirmed, after the addition of CPE-g-PS, improvement of the interfacial adhesion between the phases of the PVC/PS blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 995–1003, 1998     

Mechanical properties of ethylene–vinyl acetate/polystyrene blends studied by in situ polymerization

This study examined ethylene–vinyl acetate (EVA)‐toughened polystyrene (PS). EVA is well‐known to be incompatible with PS; thus, the PS graft to the EVA backbone (EVA‐g‐PS) was used as a compatibilizer and provided good adhesion at the interface of PS and EVA. In addition, the mechanical properties and impact resistance of the PS matrix were obviously improved by EVA‐g‐PS and by EVA itself. Meanwhile, differential scanning calorimetry results showed that the grafted PS chain influenced the crystallization of EVA; for example, the melting temperature, the crystallization temperature, and the percentage crystallinity related to EVA were reduced. Moreover, the addition of 10% EVA increased the impact strength by a factor of five but reduced the modulus by the same factor. Additionally, a lower number‐average molecular weight EVA delayed phase inversion and resulted in poor mechanical properties. A fracture surface photograph revealed that the major mechanism of EVA‐toughened PS was craze and local matrix deformation. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 699–705, 2003     

Compatibilization effect of graft copolymer on immiscible polymer blends. II. LLDPE/PS/LLDPE-g-PS systems

The compatibilizing effect of graft copolymer, linear low density polyethylene-g-polystyrene (LLDPE-g-PS), on immiscible LLDPE/PS blends has been studied by means of ¹³C CPMAS NMR and DSC techniques. The results indicate that LLDPE-g-PS is an effective compatibilizer for LLDPE/PS blends, and the compatibilizing effect of LLDPE-g-PS on LLDPE/PS blends depends on the PS grafting yield and molecular structure of the compatibilizers and also on the composition of the blends. It was found that LLDPE-g-PS chains connect two immiscible components, LLDPE and PS, through solubilization of chemically identical segments of LLDPE-g-PS into the noncrystalline region of the LLDPE and PS domain, respectively. Mean while, LLDPE-g-PS chains connect the crystalline region of LLDPE by isomorphism, resulting in an obvious change in the crystallization behavior of LLDPE. © 1996 John Wiley & Sons, Inc.     

Isotactic polypropylene/polystyrene blends: Effects of the addition of a graft copolymer of propylene with styrene

A novel graft copolymer of unsaturated propylene with styrene (uPP-g-PS) was added to binary blends of isotactic polypropylene (iPP) and atactic polystyrene (aPS) with a view to using such a copolymer as compatibilizer for iPP/aPS materials. Differential scanning calorimetry, optical microscopy, scanning electron microscopy (SEM), wide angle X-ray scattering, and small angle X-ray scattering (SAXS) techniques have been carried out to investigate the phase morphology and structure developed in solution-cast samples of iPP/aPS/uPP-g-PS ternary blends. It was found that the uPP-g-PS addition can provide iPP/aPS-compatibilized materials and that the extent of the achieved compatibilization is composition-dependent. Blends of iPP and aPS exhibited a coarse domain morphology that is characteristic of immiscible polymer systems. By adding 2% (wt/wt) of uPP-g-PS copolymer a very broad particle-size distribution was obtained, even though the particles appeared coated by a smooth interfacial layer, as expected according to a core–shell interfacial model. With increasing uPP-g-PS content (5% wt/wt), a finer dispersion degree of particles, together with morphological evidence of interfacial adhesion, was found. With further increase of uPP-g-PS amount (10% wt/wt) the material showed such a homogeneous texture that neither domains of dispersed phase nor holes could be clearly detected by SEM. The type of interface developed in such iPP/aPS/uPP-g-PS blends was accounted for by an interfacial interpenetration model. The iPP crystalline texture, size, neatness, and regularity of iPP spherulites crystallized from iPP/aPS/uPP-g-PS blends were found to decrease when the copolymer content was slightly increased. Assuming, for the iPP spherulite fibrillae, a two-phase model constituted by alternating parallel crystalline lamellae and amorphous layers, it was shown by SAXS that the phase structure generated in iPP/aPS/uPP-g-PS blends is characterized by crystalline lamellar thickness (L_c) and interlamellar amorphous layer thickness (L_a) higher than that shown by plain iPP; the higher the copolymer content, the higher the L_c and L_a. It should be remarked that considerably larger increases have been found in L_a values. Such SAXS results have been accounted for by assuming that a cocrystallization phenomenon between propylenic sequences of the uPP-g-PS copolymer and iPP occurs and that during such a process PS chains grafted into copolymer sequences remain entrapped in iPP interlamellar amorphous layers, where they form their own separate domains. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:1539–1553, 1997     

Properties of uncompatibilized and compatibilized poly(butylene terephthalate)–LLDPE blends

In this work, blends of poly(butylene terephthalate) (PBT) and linear low‐density polyethylene (LLDPE) were prepared. LLDPE was used as an impact modifier. Since the system was found to be incompatible, compatibilization was sought for by the addition of the following two types of functionalized polyethylene: ethylene vinylacetate copolymer (EVA) and maleic anhydride‐grafted EVA copolymer (EVA‐g‐MAH). The effects of the compatibilizers on the rheological and mechanical properties of the blends have been also quantitatively investigated. The impact strength of the PBT–LLDPE binary blends slightly increased at a lower concentration of LLDPE but increased remarkably above a concentration of 60 wt % of LLDPE. The morphology of the blends showed that the LLDPE particles had dispersed in the PBT matrix below 40 wt % of LLDPE, while, at 60 wt % of LLDPE, a co‐continuous morphology was obtained, which could explain the increase of the impact strength of the blend. Generally, the mechanical strength was decreased by adding LLDPE to PBT. Addition of EVA or EVA‐g‐MAH as a compatibilizer to PBT–LLDPE (70/30) blend considerably improved the impact strength of the blend without significantly sacrificing the tensile and the flexural strength. More improvement in those mechanical properties was observed in the case of the EVA‐g‐MAH system than for the EVA system. A larger viscosity increase was also observed in the case of the EVA‐g‐MAH than EVA. This may be due to interaction of the EVA‐g‐MAH with PBT. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 989–997, 1999     

Compatibility of waste rubber powder/polystyrene blends by the addition of styrene grafted styrene butadiene rubber copolymer: effect on morphology and properties

Waste rubber powder/polystyrene (WRP/PS) blends with different weight ratio were prepared with styrene grafted styrene butadiene rubber copolymer (PS-g-SBR) as a compatibilizer. The graft copolymer of PS-g-SBR was synthesized by emulsion polymerization method and confirmed through Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC). The copolymer at different weight ratio was subsequently added into the blends. The effects of weight ratio of WRP/PS and compatibilizer loading on mechanical properties were investigated. PS/WRP blends in a weight ratio of 80/20 showed higher impact strength. Moreover, the impact strength of the blend materials increased with the addition of SBR-g-PS, however, decreased at a high loading of the copolymer. The morphology and thermal properties of WRP/PS blends were examined by DSC, scanning electron microscopy (SEM), thermogravimetry (TG). DSC indicated that compared with PS/WRP blend, the glass transition temperature (T _g) of PS matrix phase in PS/WRP/SBR-g-PS blend shifted to low temperature because of the formation of chemical crosslinks or boundary layer between PS and WRP, and the T _g of WRP phase of both the PS/WRP and PS/WRP/SBR-g-PS blends did not appear. SEM results showed that interfacial adhesion in the blends with the PS-g-SBR copolymer was improved. The morphology was a typical continuous–discontinuous structure. PS and WRP presented continuous phase and discontinuous phase, respectively, indicating the moderate interface adhesion between WRP and PS matrix. TG illustrated that the onset of degradation temperature in the PS/WRP/PS-g-SBR blend decreased slightly by contrast with PS/WRP blend and the degradation of PS/WRP blends with and without SBR-g-PS was completed about at the same values.     

Polyolefin/polystyrene in situ compatibilization using Friedel–Crafts alkylation

Polyolefin/polystyrene (PS) blends are difficult to compatibilize using in situ reactive compatibilization techniques, because neither of these polymers has any functional groups that one can use in the formation of a copolymer from these polymer components. In this study, the Friedel–Crafts alkylation was realized in a polyethylene/PS (PE/PS) melt blend, which resulted in improved compatibility between PE and PS. A number of Lewis acid compounds were tested as catalysts, among which the AlCl₃ was the most efficient. It was found in this study that the presence of a cocatalyst, such as a cationically polymerizable monomer or a halogenated alkane, significantly enhances the formation of PE-g-PS copolymer. The effects of blending parameters, such as temperature and blending time, on the in situ copolymer formation were investigated. The mechanical properties of compatibilized PE/PS blends were improved considerably. Such an in situ compatibilization technique has potential in the recycling of mixed polymer wastes. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 1385–1393, 1997     

Effect of in situ synthesized macroactivator on morphology of PA6/PS blends via successive polymerization

In situ polymerization and in situ compatibilization was adopted for preparation of ternary PA6/PS‐g‐PA6/PS blends by means of successive polymerization of styrene, with TMI and ε‐caprolactam, via free radical copolymerization and anionic ring‐opening polymerization, respectively. Copolymer poly(St‐g‐TMI), the chain of which bears isocyanate (? NCO), acts as a macroactivator to initiate PA6 chain growth from the PS chain and graft copolymer of PS‐g‐PA6 and pure PA6 form, simultaneously. The effect of the macroactivator poly(St‐g‐TMI) on the phase morphology was investigated in detail, using scanning electron microscopy. In case of blends with higher content of PS‐g‐PA6 copolymer, copolymer nanoparticles coexisting with the PS formed the matrix, in which PA6 microspheres were dispersed evenly as minor phase. The content of the compositions (homopolystyrene, homopolyamide 6, and PS‐g‐PA6) of the blends were determined by selective solvent extraction technique. The mechanical properties of PA6/PS‐g‐PA6/PS blends were better than that of PA6/PS blends. Especially for the blends T10 with lower PS‐g‐PA6 copolymer content, both the flexural strength and flexural modulus showed significantly improving because of the improved interfacial adhesion between PS and PA6. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Improvement of mechanical properties for PP/PS blends by in situ compatibilization

The effect of the in situ compatibilization on the mechanical properties of PP/PS blends was investigated. The application of Friedel-Crafts alkylation reaction to the PP/PS-blend compatibilization was assessed. Styrene/AlCl₃ was used as catalyst system. The graft copolymer (PP-g-PS) formed at the interphase showed relatively high emulsifying strength. Scission reactions, occurring in parallel with grafting, were verified for PP and PS at high catalyst concentration, but no crosslinking reactions were detected. Tensile tests were performed on dog-bone specimens of the blends. Both elongation at break and toughness increased with catalyst concentration. At 0.7% AlCl₃, a maximum was reached, which amounted to five times the value of the property for the uncompatibilized blend. At higher catalyst concentrations these properties decreased along with the PP molecular weight due to chain-scission reactions. On the other hand, the tensile strength did not change with the catalyst concentration. The in situ compatibilized blends showed considerable improvement in mechanical properties, but were adversely affected by chain scissions at high catalyst contents.     

Compatibilizing effects of poly(styrene-graft-ethylene oxide) in blends of polystyrene and butyl acrylate polymers

The compatibilizing effect of poly(styrene-graft-ethylene oxide) in polystyrene (PS) blends with poly(n-butyl acrylate) (PBA) and poly(n-butyl acrylate-co-acrylic acid) (PBAAA) was investigated. No significant effects of the graft copolymer on the domain size were found in the PBA blends. By functionalizing PBA with acrylic acid, the average size of the polyacrylate domains was reduced considerably by the graft copolymer. Thermal and dynamic mechanical analysis of the PS/PBAAA blends revealed that the PBAAA glass transition temperature (T_g) decreased with increasing graft copolymer content. The effect of the graft copolymer in the PS/PBAAA blends can be explained by interactions across the interface due to the formation of hydrogen bonds between the poly(ethylene oxide) (PEO) side chains in the graft copolymer and the acrylic acid segments in the PBAAA phase. Hydrogen bonding was confirmed by IR analysis of binary blends of PEO and PBAAA. Partial miscibility in the PEO/PBAAA blends was indicated by a PEO melting point depression and by a T_g reduction of the PBAAA phase. The thermal properties of the PEO/PBA blends indicated only very limited miscibility. © 1996 John Wiley & Sons, Inc.     

Effect of the molecular architecture of graft copolymers on the phase morphology and tensile properties of PS/EVA blends

Graft copolymers of poly(ethylene‐co‐vinyl acetate) (EVA) grafted with polystyrene (PS) with different molecular weight and different EVA/PS ratio were prepared by coupling reaction between acyl chloride functionalized PS (PS‐COCl) and hydrolyzed EVA. PS‐COCl with controlled molecular weight was prepared by anionic polymerization of styrene, followed by end capping with phosgene. The effect of the molecular architecture of the graft copolymer on the compatibilization of PS/EVA blends was investigated. Substantial improvement in the elongation at break and ductility was observed using the graft copolymer with PS segments with molecular weight as high as 66,000 g/mol and with a PS proportion equal or higher than EVA. The effect of the compatibilization on the morphology was also investigated by scanning electron microscopy and atomic force microscopy. The blend that presented the highest value of elongation at break also displayed dispersed phase constituted by inclusions of the PS phase inside the EVA particle forming a cocontinuous structure, as observed by AFM. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Relationship between structure and properties in high‐performance PA6/SEBS‐g‐MA/(PPO/PS) blends: The role of PPO and PS

This work aimed at studying the role of poly(phenylene oxide) (PPO) and polystyrene (PS) in toughening polyamide‐6 (PA6)/styrene‐ethylene‐butadiene‐styrene block copolymer grafted with maleic anhydride (SEBS‐g‐MA) blends. The effects of weight ratio and content of PPO/PS on the morphology and mechanical behaviors of PA6/SEBS‐g‐MA/(PPO/PS) blends were studied by scanning electron microscope and mechanical tests. Driving by the interfacial tension and the spreading coefficient, the “core–shell” particles formed by PPO/PS (core) and SEBS‐g‐MA (shell) played the key role in toughening the PA6 blends. As PS improved the distribution of the “core–shell” particles due to its low viscosity, and PPO guaranteed the entanglement density of the PPO/PS phase, the 3/1 weight ratio of PPO/PS supplied the blends optimal mechanical properties. Within certain range, the increased content of PPO/PS could supply more efficient toughening particles and bring better mechanical properties. Thus, by adjusting the weight ratio and content of PPO and PS, the PA6/SEBS‐g‐MA/(PPO/PS) blends with excellent impact strength, high tensile strength, and good heat deflection temperature were obtained. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45281.     

Blends of poly(vinyl chloride) (PVC)/natural rubber‐g‐(styrene‐co‐methyl methacrylate) for improved impact resistance of PVC

To improve the mechanical properties of poly(vinyl chloride) (PVC), the possibility of combining PVC with elastomers was considered. Modification of natural rubber (NR) by graft copolymerization with methyl methacrylate (MMA) and styrene (St) was carried out by emulsion polymerization by using redox initiator to provide an impact modifier for PVC. The impact resistance, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM) of St and MMA grafted NR [NR‐g‐(St‐co‐MMA)]/PVC (graft copolymer product contents of 5, 10, and 15%) blends were investigated as a function of the amount of graft copolymer product. It was found that the impact strength of blends was increased with an increase of the graft copolymer product content. DMA studies showed that NR‐g‐(St‐co‐MMA) has partial compatibility with PVC. SEM confirmed a shift from brittle failure to ductility with an increase graft copolymer content in the blends. The mechanical properties showed that NR‐g‐(St‐co‐MMA) interacts well with PVC and can also be used as an impact modifier for PVC. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1666–1672, 2004     

Toughening effects of ethylene–vinyl acetate copolymers with different vinyl acetate content and viscosity on nylon 1010 blends

Nylon 1010 blends with ethylene–vinyl acetate copolymer (EVA) and maleated ethylene–vinyl acetate (EVA‐g‐MAH) were prepared through melt blending. The vinyl acetate (VA) content and viscosity of EVA significantly affected the notched impact strength of nylon/EVA/EVA‐g‐MAH (80/15/5) blends. The nylon/EVA/EVA‐g‐MAH blends with high notched impact strength (over 60 kJ/m²) were obtained when the VA content in EVA ranged from 28 to 60 wt%. The effect of VA content on the notched impact strength of blends was related to the glass transition temperature for EVA with high VA content and crystallinity for EVA with low VA content. For nylon blends with EVA with the same VA content, low viscosity of EVA led to high notched impact strength. Fracture morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends showed that blends with ductile fracture behavior usually had large matrix plastic deformation, which was the main energy dissipation mechanism. A relationship between the notched impact strength and the morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends was well correlated by the interparticle distance model. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Reactively formed block and graft copolymers as compatibilizers for polyamide 66/PS blends

Phthalic anhydride terminated polystyrene (PS-An) and styrene-maleic anhydride copolymer (SMA) were compared as a compatibilizer at low loadings (<10 wt%) in 70/30 polyamide 66 (PA66)/polystyrene (PS) blends. Compatibilization efficiency was judged by morphology of the blends and the extent of interfacial coupling to copolymer. Fluorescent labels of functional PS's (anthracene and pyrene for PS-An and SMA, respectively) allowed the detection of small amounts of reactively formed block (PA66-b-PS) or graft copolymer (SMA-g-PA66) in the blends via gel permeation chromatography with a fluorescence detector. Extremely fast reactions giving >60% conversion in 0.5 min mixing were observed regardless of the molecular weight, the structure, and the amount of the functional PS's. Interfacial stability of the reactively formed copolymers was estimated by micelle formation in the bulk phases and the interfacial coverage, Σ. PS-An with higher molecular weight (37 kg/mol) was most effective as a compatibilizer at the interface, showing less tendency to form microemulsions by suppressing interfacial roughening. However, a large portion of PA66-b-PS from low molecular weight PS-An (10 kg/mol) and SMA-g-PA66 from random functional SMA (16 kg/mol) migrated to the bulk phase to form micelles even at <2 wt% loadings. Blends of PA66 with syndiotactic PS compatibilized with PS-An gave very similar morphology to the PA66/PS blends indicating that these conclusions apply also to PA66/sPS blends.     

Relationship between branch length and the compatibilizing effect of polypropylene‐g‐polystyrene graft copolymer on polypropylene/polystyrene blends

Three polypropylene‐g‐polystyrene (PP‐g‐PS) graft copolymers with the same branch density but different branch lengths were evaluated as compatibilizing agents for PP/PS blends. The morphological and rheological results revealed that the addition of PP‐g‐PS graft copolymers significantly reduced the PS particle size and enhanced the interfacial adhesion between PP and PS phases. Furthermore, it is verified that the branch length of PP‐g‐PS graft copolymer had opposite effects on its compatibilizing effect: on one hand, increasing the branch length could improve the compatibilizing effect of graft copolymer on PP/PS blends, demonstrated by the reduction of PS particle size and the enhancement of interfacial adhesion; on the other hand, increasing the branch length would increase the melt viscosity of PP‐g‐PS graft copolymer, which prevented it from migrating effectively to the interface of blend components. Additionally, the crystallization and melting behaviors of PP and PP/PS blends were compared. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40126.     

A new method in designing compatibility and adhesion of EVA/PMMA blend by using EVA-<Emphasis Type="Italic">g</Emphasis>-PMMA with controlled graft chain length

Atom transfer free radical polymerization (ATRP) was employed in a synthesis of graft polymer EVA-g-PMMA with controlled length of side PMMA chains. Three steps of synthesis: partial hydrolysis of EVA, esterification with chloroacetyl chloride and ATRP grafting were performed to produce EVAOH, macroinitiator EVACl and grafted polymers G8020 (EVA/PMMA?=?80/20 wt%) and G6040 (EVA/PMMA?=?60/40 wt%). FTIR, Raman and NMR spectroscopy were used in the determination of the chemical structure and modification of EVA. Transmitted light and dark field microscopy showed higher affinity for coil formation of EVA-g-PMMA with longer PMMA side chains, i.e. G6040 compatibilizer. Morphological, thermal and adhesive properties of optical fiber adhesives of graft polymers and polymer blends poly(ethylene-co-vinyl acetate)-blend-poly(methyl methacrylate) (EVA/PMMA) compatibilized with 1 wt% of EVA-g-PMMA, were studied. Image analysis of SEM micrographs showed effective compatibilization with short grafted chains (G8020) that was indicated by lower porosity characteristics. TG/DTG analysis enabled determination of degree of hydrolysis and amount of chloro-functionalized groups. DSC analysis showed higher thermal stability of G8020 polymer. Single lap joint of adhesives/optical fibers were subjected to adhesive testing and obtained results for maximal force applied and adhesive failure suggested the visible influence of the length of graft chains on adhesion.     

Controllable Synthesis of Submicrometer Core–Shell Modifier and Its Effect on Toughening Polypheylene Ether/Polystyrene Blends

Core–shell polybutadiene-graft-polystyrene (PB-g-PS) graft copolymers with different ratios of PB to PS are synthesized by emulsion polymerization. Further, the PB-g-PS copolymers are blended with polypheylene ether (PPE) and PS to prepare PPE/PS/PB-g-PS blends. The effects of PB-g-PS copolymer structure and matrix composition on the morphological, mechanical properties, and deformation mechanism of the blends are studied. The results show that the synthesized submicrometer-sized PB-g-PS copolymer has an excellent toughening efficiency, both the copolymer and PS are introduced into PPE resin to produce a ternary blend which is combined with high toughness and processing properties. The optimum toughening effect on PPE/PS matrix is observed at the core–shell weight ratio of 70/30 in PB-g-PS copolymer, and the impact strength of the blends increased from 101 to 550 J m⁻¹. In addition, the dispersion pattern of rubber particles in the matrix gradually changes from uniform dispersion to aggregation as the core–shell ratio of PB-g-PS copolymers increases. On the other hand, with the increase of PPE content, the dispersion of rubber particles in PPE/PS matrix is improved, and the deformation mechanism is changed from cracking to a combination of crazing and shear yielding, which can lead to absorb more energy to achieve better toughness.