Processing conditions for electromagnetic interference shielding effectiveness and mechanical properties of acrylonitrile-butadiene-styrene based composites

A conductive plastic was compounded in a twin screw extruder by incorporating conductive carbon fiber (CF) into an acrylonitrile-butadience-styrene (ABS) copolymer. The effects of various processing parameters prior to injection molding were investigated; then, the electromagnetic interference shielding effectiveness (EMI SE), fiber length, processability, and mechanical properties of the composite were studied. Results showed that the EMI SE of the composite increased as the final fiber length increased. The longer final fiber was produced by feeding fibers into the ABS melt at 240°C and 60 rpm. A more conductive network was formed by adding lubricants to the composite to reduce fiber damage and increase fiber dispersion. The increase of the fiber content affected processability. When the fiber content was higher than 40 phr (parts per hundred resin) in the composite, the average fiber length shortened. This study shows that better shielding can be obtained by adding a fiber at a rate higher than 30 phr. The best shielding obtained is about 30 decibels (dB).     

ASA/graphite/carbon black composites with improved EMI SE,conductivity and heat resistance properties

Composites, comprised of acrylonitrile styrene acrylate copolymer (ASA)/graphite (GR) with high electromagnetic interference shielding effectiveness (EMI SE), were fabricated by the introduction of carbon black (CB). The effects of CB on properties such as EMI SE, morphology, heat resistance, rheological and mechanical performance of the composites were characterized using a scanning electron microscope (SEM), rotational rheometer, electromagnetic shielding measuring instruments. The graphite and carbon black exhibited positive synergistic action, which promoted the complete formation of conductive networks in ASA matrix. The EMI SE and electrical conductivity of the ASA/GR/CB composites increased with higher CB loadings. In the frequency range of 30–3000 MHz, the maximum EMI SE of ASA composites with 50 % fillers reached 40 dB, but with 40 % fillers this property reached its maximum value of 50 dB. The flexural strength of ASA/GR/CB composites started to decline as CB loading exceeded 5 %. The heat resistance of the composites was improved due to the addition of CB. In this respect, the vicar softening temperature (VST) of the composites with 40 % fillers increased from 115.1 to 132.7 °C, and the VST of the composites with 50 % fillers was elevated from 125.4 to 138.9 °C.     

Ti3C2Tx-coated diatom frustules-derived porous SiO2 composites with high EMI shielding and mechanical properties

Effective electromagnetic interference (EMI) shielding materials have garnered substantial interest for their efficacy in attenuating electromagnetic wave energy, ensuring data confidentiality, ensuring the operational stability of fragile electronic systems. To begin, artificially cultured diatom frustules (DF)-derived porous silica (DFPS) skeletons were constructed as templates in this study. Porous ceramics hot-pressed at 800 °C displayed a high compressive strength with a high specific surface area due to their three-dimensional (3D) multilayered and porous structures. Then, mechanically robust Ti₃C₂T_x/DFPS composites with exceptional EMI shielding performance were fabricated by immersing porous DF-based ceramics into Ti₃C₂T_x solutions and annealing in an argon environment to increase the materials’ shielding efficiency (SE). The EMI SE of composites hot-pressed at 800 °C achieved the maximum EMI SE of 43.2 dB in the X-band and a compressive strength of 67.5 MPa, establishing a hitherto unreported balance of mechanical characteristics and shielding performance. Prolonged transmission paths, multiple dissipation, scattering and reflection of electromagnetic energy were achieved using a well-maintained hierarchical porous silica framework decorated with MXene, with adsorption caused by surface MXene serving as the primary shielding mechanism for the composites. Due to their superior overall performance, MXene/DFPS EMI shielding composites have a bright future in the aircraft sector as delicate electronic device components.     

Effects of molding conditions on the electromagnetic interference performance of conductive ABS parts

Polymers filled with conducting fibers to prevent electromagnetic interference (EMI) performance have recently received great attention due to the requirements of 3C (computer, communication, and consumer electronics) products. In the present article, the effect of fiber content and processing parameters, including melt temperature, mold temperature, and injection velocity, on the electromagnetic interference shielding effectiveness (SE) in injection molded ABS polymer composites filled with conductive stainless steel fiber (SSF) was investigated. The influence of fiber orientation and distribution resulting from fiber content and molding conditions on EMI performance was also examined. It was found from measured results that fiber content plays a significant role in influencing part EMI SE performance. SE value can reach the highest values of approximately 40 dB and 60 dB at 1000 MHz frequency for fiber content 7 wt % and 14 wt %, respectively, under the best choice of molding conditions. Higher melt and mold temperature would increase shielding effectiveness due to a more uniform and random fiber orientation. However, higher injection velocity leading to highly‐orientated and less uniform distribution of fiber reduces shielding effectiveness. Among all molding parameters, melt temperature affects SE performance most significantly. Its influence slightly decreases as fiber content increases. Injection speed plays a secondary importance in affecting SE values, and its influence increases as fiber content increases. Upon examination of fiber distribution via optical microscope and subsequent image analysis, it was found that the fiber becomes more densely and random distributed toward the last melt‐filled region, whereas fiber exhibits less concentration around the middle way of the flow path. This can be attributed to the combined effects of fountain flow, frozen layer thickness, and gapwise melt front velocity. The results indicate that molding conditions, instead of fiber content alone, are very important on the SE performance for injection molded SSF filled ABS composites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1072–1080, 2005     

Hybrid composites of ABS with carbonaceous fillers for electromagnetic shielding applications

This work evaluates the influence of two types of carbonaceous fillers, carbon black (CB) and carbon nanotubes (CNTs), on the electrical, electromagnetic, and rheological properties of composites based on poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) prepared by the melt mixing. Electrical conductivity, electromagnetic shielding efficiency (EMI SE) in the X‐band frequency range (8–12.4 GHz), and melt flow index (MFI) results showed that ABS/CNT composites exhibit higher electrical conductivity and EMI SE, but lower MFI when compared to ABS/CB composites. The electrical conductivity of the binary composites showed an increase of around 16 orders of magnitude, when compared to neat ABS, for both fillers. Binary composites with 5 and 15 wt % of filler showed an EMI SE of, respectively, ?44 and ?83 dB for ABS/CNT, and ?9 and ?34 dB for ABS/CB. MFI for binary composites with 5 wt % were 15.45 and 0.55 g/10 min for CB and CNT, respectively. Hybrid composites ABS/CNT.CB with 3 wt % total filler and fraction 50:50 and 75:25 showed good correlation between EMI SE and MFI. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46546.     

Electrical conductivity and thermal properties of acrylonitrile‐butadiene‐styrene filled with multiwall carbon nanotubes

Composites of Acrylonitrile‐butadiene‐styrene (ABS) and multiwall carbon nanotubes (MWNTs) have been prepared via solution‐blending. The electrical conductivity of these composites is analyzed. The MWNT‐filled ABS shows percolation point of the electrical conductivity at low filler loadings (1–2 wt%). The micro‐structure of the composites is also analyzed by scanning electron microscopy showing that the nanotubes are dispersed quite homogeneously in the polymer‐matrix. The thermogravimetric analysis is used to study the thermal degradation of ABS/MWNTs composites in nitrogen. MWNTs tend to destabilize the ABS matrix in the 220–450°C degradation regions but improve the thermal stability in the 425–850°C regions. With further addition of MWNTs, the features of the destabilization in the 220–450°C degradation region did not change much but in the 425–850°C degradation process, the MWNTs reinforced stabilization and the quality of the char residue of amorphous carbon deposition was improved. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Highly filled multilayer thermoplastic/graphene conducting composite structures with high strength and thermal stability for electromagnetic interference shielding applications

Polyvinyl chloride (PVC)/graphene and poly(methyl methacrylate) (PMMA)/graphene nanocomposites were made by solution casting technique with graphene weight fractions of 1, 5, 10, 15, and 20%. Multilayer structures of the composites were made by hot compression technique to study their electromagnetic interference shielding effectiveness (EMI SE). Tensile strength, hardness, and storage modulus of the nanocomposites were studied in relation with graphene weight fraction. There has been a substantial increase in the electrical conductivity and EMI SE of the composites with 15–20% filler loading. Differential thermal analysis of the composites shows improved thermal stability with an increase in graphene loading. PMMA/graphene composites have better thermal stability, whereas PVC/graphene composites have superior mechanical properties. About 2 mm thick multilayer structures of PMMA/graphene and PVC/graphene composites show a maximum EMI SE of 21 dB and 31 dB, respectively, in the X band at 20 wt % graphene loading. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47792.     

Mechanical,thermal, and dielectric properties of SiCf/SiC composites reinforced with electrospun SiC fibers by PIP

Electrospun unidirectional SiC fibers reinforced SiC_f/SiC composites (e-SiC_f/SiC) were prepared with ∼10% volume fraction by polymer infiltration and pyrolysis (PIP) process. Pyrolysis temperature was varied to investigate the changes in microstructures, mechanical, thermal, and dielectric properties of e-SiC_f/SiC composites. The composites prepared at 1100 °C exhibit the highest flexural strength of 286.0 ± 33.9 MPa, then reduced at 1300 °C, mainly due to the degradation of electrospun SiC fibers, increased porosity, and reaction-controlled interfacial bonding. The thermal conductivity of e-SiC_f/SiC prepared at 1300 °C reached 2.663 W/(m∙K). The dielectric properties of e-SiC_f/SiC composites were also investigated and the complex permittivities increase with raising pyrolysis temperature. The e-SiC_f/SiC composites prepared at 1300 °C exhibited EMI shielding effectiveness exceeding 24 dB over the whole X band. The electrospun SiC fibers reinforced SiC_f/SiC composites can serve as a potential material for structural components and EMI shielding applications in the future.     

Graphene nanoplate and multiwall carbon nanotube–embedded polycarbonate hybrid composites: High electromagnetic interference shielding with low percolation threshold

This study has reported the preparation of polycarbonate (PC)/graphene nanoplate (GNP)/multiwall carbon nanotube (MWCNT) hybrid composite by simple melt mixing method of PC with GNP and MWCNT at 330°C above the processing temperature of the PC (processing temperature is 280°C) followed by compression molding. Through optimizing the ratio of (GNP/MWCNT) in the composites, high electromagnetic interference shielding effectiveness (EMI SE) value (∼21.6 dB) was achieved at low (4 wt%) loading of (GNP/MWCNT) and electrical conductivity of ≈6.84 × 10⁻⁵ S.cm⁻¹ was achieved at 0.3 wt% (GNP/MWCNT) loading with low percolation threshold (≈0.072 wt%). The high temperature melt mixing of PC with nanofillers lowers the melt viscosity of the PC that has helped for better dispersion of the GNPs and MWCNTs in the PC matrix and plays a key factor for achieving high EMI shielding value and high electrical conductivity with low percolation threshold than ever reported in PC/MWCNT or PC/graphene composites. With this method, the formation of continuous conducting interconnected GNP‐CNT‐GNP or CNT‐GNP‐CNT network structure in the matrix polymer and strong π–π interaction between the electron rich phenyl rings and oxygen atom of PC chain, GNP, and MWCNT could be possible throughout the composites. POLYM. COMPOS., 37:2058–2069, 2016. © 2015 Society of Plastics Engineers     

Electrical,rheological and electromagnetic interference shielding properties of thermoplastic polyurethane/carbon nanotube composites

Electrically conducting rubbery composites based on thermoplastic polyurethane (TPU) and carbon nanotubes (CNTs) were prepared through melt blending using a torque rheometer equipped with a mixing chamber. The electrical conductivity, morphology, rheological properties and electromagnetic interference shielding effectiveness (EMI SE) of the TPU/CNT composites were evaluated and also compared with those of carbon black (CB)‐filled TPU composites prepared under the same processing conditions. For both polymer systems, the insulator–conductor transition was very sharp and the electrical percolation threshold at room temperature was at CNT and CB contents of about 1.0 and 1.7 wt%, respectively. The EMI SE over the X‐band frequency range (8–12 GHz) for TPU/CNT and TPU/CB composites was investigated as a function of filler content. EMI SE and electrical conductivity increased with increasing amount of conductive filler, due to the formation of conductive pathways in the TPU matrix. TPU/CNT composites displayed higher electrical conductivity and EMI SE than TPU/CB composites with similar conductive filler content. EMI SE values found for TPU/CNT and TPU/CB composites containing 10 and 15 wt% conductive fillers, respectively, were in the range ?22 to ?20 dB, indicating that these composites are promising candidates for shielding applications. © 2013 Society of Chemical Industry     

Conducting polyaniline composite for ESD and EMI at 101 GHz

Conducting polyaniline forms an important family of electronic polymers with a developed potential application for a number of areas because of their flexible chemistry, processibility, environmental stability and ease of forming composites. The electromagnetic interference shielding effectiveness of conducting polyaniline (PANI)–ABS composites was studied at 101 GHz. It was observed that shielding effectiveness of the PANI–ABS composites increases with the increase in the loading levels of the conducting polymer doped with hybrid dopants. The lower loading of PANI doped with hybrid dopants in the moulded conducting composites can be effectively used for the dissipation of electrostatic charge. However, with higher loadings, a shielding effectiveness of 60 dB has been achieved which makes the conducting composites a potential EMI shielding material for its application in encapsulation of electronic equipments in electronic and in high tech applications.     

Electromagnetic interference shielding properties of graphene quantum-dots reinforced poly(vinyl alcohol)/polypyrrole blend nanocomposites

Graphene quantum dots (GQDs) reinforced poly(vinyl alcohol) (PVA)/polypyrrole (WPPy) nanocomposite films with various GQDs loadings were synthesized using the versatile solvent casting method. The structural and morphological properties of PVA/WPPy/GQDs nanocomposite films were investigated by employing Fourier transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. The thermogravimetric analysis revealed enhanced thermal stability of synthesized nanocomposites while enhanced dielectric properties were also observed. The maximum dielectric constant value for PVA/WPPy/GQDs nanocomposite films was observed to be ε = 6,311.85 (50 Hz, 150°C). The electromagnetic interference (EMI) shielding effectiveness (SE) of nanocomposite films was determined in the X-band (8–12 GHz) and Ku-band (12–18 GHz) frequency region. The EMI SE was found to be increased from 0.8 dB for the pure PVA film to 9.8 dB for the PVA/WPPy/GQDs nanocomposite film containing 10 wt% GQDs loading. The enhanced EMI shielding efficiency of nanocomposite films has resulted from the homogenous dispersion of GQDs in PVA/WPPy blend nanocomposites. Thus, the prepared nanocomposites are envisioned to utilize as a lightweight, flexible, and low-cost material for EMI shielding applications.     

Investigation of the Effects of Injection Molding Processing Parameters on Conductive Polymeric Composites for Electromagnetic Interference Shielding Effectiveness

Polycarbonate (PC) composites filled with conductive nickel-coated carbon fibers (NCFs) were injection-molded under different injection process conditions. They were then used to investigate the influence of the injection processing parameters of melt temperature, mold temperature, injection velocity and packing pressure on the electromagnetic interference (EMI) shielding effectiveness (SE). In order to study the effect of the molding variables using the minimum number of experiments, the Taguchi method was employed. The aim of the Taguchi method was to optimize the injection processing parameters for better EMI shielding of the conductive polycarbonate composites. It is found out that the packing pressure and mold temperature affect the EMI shielding efficiency most significantly.     

Microwave Absorbing Performances of Silica Matrix Composites Reinforced by Carbon Nanotubes and Carbon Fiber

Multilayered composites consisting of silica, carbon nanotubes (CNTs), and continuous carbon fibers (C_f) were prepared by hot‐pressing technique. Microstructures of different layer presented few pores of the composites. The thermal stability of the composites was analyzed by TG/DTA measurement. After being heat treated at 400°C for 10 h, the composites retained the equivalent shielding property compared to room temperature, and the impedance matching property at material/wave interface was improved slightly. The multilayer CNTs/C_f/silica composites have not only the excellent absorbing properties but also the outstanding thermal stability, and it can be a promising candidate for high‐temperature electromagnetic interference shielding applications.     

Electrical properties and EMI shielding characteristics of polypyrrole–nylon 6 composite fabrics

Polypyrrole (PPy) was polymerized both chemically and electrochemically in sequence on nylon 6 woven fabrics, giving rise to polypyrrole–nylon 6 composite fabrics (PPy–N) with a high electric conductivity. The stability of the composite prepared by electrochemical polymerization (ECP) on chemical oxidative polymerization (COP) fabric was better than that of the composite prepared solely by the COP process, since the AQSA dopant was able to strongly interact with the PPy main chain and had a large molecular structure. The temperature dependence of the conductivity of the composites was verified over four heating and cooling cycles. The change in conductivity over these four repeated heating and cooling cycles was affected by the interaction between the thermal stability of the dopant and the rearrangement of the PPy main chain. The electromagnetic interference shielding efficiency (EMI SE) values were in the range 5–40 dB and depended on the conductivity and the layer array sequence of the conductive fabric. The composites with a high conductivity represented reflection‐dominant EMI shielding characteristics, which are typical of the EMI shielding characteristics of metals. However, composites with low conductivity showed absorption‐dominant EMI shielding characteristics. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1969–1974, 2003     

Efficient fabrication of carbon/silicon carbide composite for electromagnetic interference shielding applications

Ceramic matrix composites are typically prepared by a costly, time-consuming process under severe conditions. Herein, a cost-effective C/SiC composite was fabricated from a silicon gel-derived source by Joule heating. The β-SiC phase was generated via carbothermal reduction, and the carbon fabric showed a well-developed graphitic structure, promoting its thermal and anti-oxidation stabilities. Owing to the excellent dielectric loss in carbon fabric, SiC and SiO₂ as well as the micropore structure of the ceramic matrix, the absolute electromagnetic interference shielding (EMI) effectiveness (SSE/t) reached 948.18 dB?cm²?g^-1 in the X-band, exhibiting an excellent EMI SE. After oxidation at 1000 °C for 10 h in the air, the SSE/t of the composite was only reduced to 846.02 dB?cm²?g^-1. The C/SiC composite promises the efficient fabrication of high-temperature resistant materials for electromagnetic shielding applications.     

Synergistically improved thermal stability and electromagnetic interference shielding effectiveness (EMI SE) of in-situ synthesized polyaniline/sulphur doped reduced graphene oxide (PANI/S-RGO) nanocomposites

Polyaniline (PANI) and its composite with sulphur doped reduced graphene oxide (S-RGO) have been successively synthesized via in-situ chemical oxidative polymerization of aniline in presence of 10 wt. % S-RGO nanosheets. Physico-chemical analyses of the synthesized nanomaterial was performed with various characterization techniques such as X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS), Atomic Force Microscopy (AFM) and Thermogravimetric analysis/Differential Scanning Calorimetry (TGA/DSC). The results interpreted from the various characterizations confirm the doping of RGO with sulphur as well as strong interaction of PANI nanofibers and S-RGO nanosheets. TG/DSC curves confirm the enhanced thermal stability of polyaniline/sulphur doped reduced graphene oxide (PANI/S-RGO) nanocomposites with heat resistance index (T_HRI) of 155.2 °C in comparision to pure PANI (T_HRI = 145.3 °C) at a filler loading of 10 wt. %. TGA validates that thermal stability of PANI/S-RGO nanocomposite improves by 6–7 °C than pure PANI in terms of weight loss percentage at a temperature of 1117 °C. However DSC analysis confirms that PANI/S-RGO retains its structural integrity and conformity to temperatures as high as 900 °C beyond which the polymer composite starts to degrade. The electromagnetic interference shielding effectiveness (EMI SE) of PANI and PANI/S-RGO nanocomposites were measured via open-ended coaxial probe set-up connected to a Vector Network Analyser (VNA) at a broadband frequency range of 1–20 GHz (1000–20000 MHz). For EMI SE measurements the various nanomaterials were incorporated into paraffin wax and made into composite pellets of thickness 5 mm by solution casting technique. The dielectric properties, electrical conductivity and EMI SE were all greatly enhanced for the PANI/S-RGO/Paraffin composite pellets. The as synthesized PANI/S-RGO/Paraffin composite pellets exhibited highest EMI SE of ?22.5 dB (>99%) as compared to ?15.89 dB of PANI/Paraffin composite pellets. The prepared composite pellets revealed an absorption dominant mechanism of shielding with highest SE_A of ?14.6 dB for PANI/S-RGO/Paraffin composite pellets.     

Electromagnetic interference shielding mechanisms of CNT/polymer composites

The electromagnetic interference (EMI) shielding mechanisms of multi-walled carbon nanotube (MWCNT)/polymer composites were analyzed experimentally and theoretically. For the experimental analysis, EMI shielding effectiveness (SE) of MWCNT/polypropylene (PP) composite plates made in three different thicknesses and at four different concentrations were studied. A model based on the shielding of electromagnetic plane wave was used to theoretically study the EMI shielding mechanisms. The experimental results showed that absorption is the major shielding mechanism and reflection is the secondary shielding mechanism. The modeling results demonstrated that multiple-reflection within MWCNT internal surfaces and between MWCNT external surfaces decrease the overall EMI SE. The EMI SE of MWCNT/PP composites increased with increase in MWCNT content and shielding plate thickness.     

Epoxy composite foams with excellent electromagnetic interference shielding and heat‐resistance performance

Epoxy composite foams with improved heat‐resistant property and efficient electromagnetic interference shielding effectiveness (EMI SE) were fabricated through a two‐step foaming technique. A sort of novel and untraditional expandable microspheres was adopted to reduce the density of prepared materials. A multiscale conductive network system composed of multiwalled carbon nanotubes (MWCNTs) and nickel‐plated carbon fibers (NiCFs) was introduced in these foams. Benefitting from the synergistic effect between NiCFs and MWCNTs, the multiscale epoxy foam with best comprehensive performance achieved a greatly enhanced T_g at 178.3 °C and an exceptional specific EMI SE ranging from 52.8 to 72.6 dB cm³ g^?1 in X band (8.2–12.4 GHz) at low filler loading. These properties are greatly better than original epoxy foam with a T_g of 157.8 °C and specific EMI SE of 1.0–6.4 dB cm³ g^?1. Their shielding mechanisms were discussed and the results showed that reflection is dominating. The effects of microspheres content, foaming temperature, NiCFs content, and length were investigated. In general, we provided a feasible, convenient and cost‐effective method to fabricate light‐weight, heat‐resistant thermosetting epoxy foams with sufficient EMI shielding performance which has a potential to be applied in aerospace or electronic devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46013.     

Multiwalled carbon nanotubes–BaTiO3/silica composites with high complex permittivity and improved electromagnetic interference shielding at elevated temperature

Composites with silica matrix and mixed filler of multiwalled carbon nanotubes (MWCNTs) and BaTiO₃ powder were fabricated. Excellent uniform dispersion of MWCNTs can be obtained using a two-step mixing method. Both of the real and imaginary parts of complex permittivity increased with increasing MWCNT content and measured temperature. The electromagnetic interference (EMI) shielding results showed that the absorption mechanism is the main contribution to the total EMI shielding effectiveness (SE). Compared with the EMI SE resulting from reflection, the absorption showed more dependence on the MWCNT content, measured temperature and frequency. The total EMI SE is greater than 20 dB at 25 °C and 50 dB at 600 °C in the whole frequency range of 12.4–18 GHz with a 1.5 mm composite thickness, which suggests that the MWCNT–BaTiO₃/silica composites could be good candidates for the EMI shielding materials in the measured frequency and temperature region.