Highly optical transparency and thermally stable polyimides containing pyridine and phenyl pendant

In order to obtain highly optical transparency polyimides, two novel aromatic diamine monomers containing pyridine and kinky structures, 1,1-bis[4-(5-amino-2-pyridinoxy)phenyl]diphenylmethane (BAPDBP) and 1,1-bis[4-(5-amino-2-pyridinoxy)phenyl]-1-phenylethane (BAPDAP), were designed and synthesized. Polyimides based on BAPDBP, BAPDAP, 2,2-bis[4-(5-amino-2-pyridinoxy)phenyl]propane (BAPDP) with various commercial dianhydrides were prepared for comparison and structure-property relationships study. The structures of the polyimides were characterized by Fourier transform infrared (FT-IR) spectrometer, wide-angle X-ray diffractograms (XRD) and elemental analysis. Film properties including solubility, optical transparency, water uptake, thermal and mechanical properties were also evaluated. The introduction of pyridine and kinky structure into the backbones that polyimides presented good optical properties with 91–97% transparent at 500 nm and a low cut-off wavelength at 353–398 nm. Moreover, phenyl pendant groups of the polyimides showed high glass transition temperatures (T_g) in the range of 257–281 °C. These results suggest that the incorporating pyridine, kinky and bulky substituents to polymer backbone can improve the optical transparency effectively without sacrificing the thermal properties.     

Organosoluble and light‐colored fluorinated polyimides based on 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]propane and aromatic dianhydrides

A novel fluorinated diamine monomer, 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]propane (2), was prepared through the nucleophilic substitution reaction of 2‐chloro‐5‐nitrobenzotrifluoride with 2,2‐bis(4‐hydroxyphenyl)propane in the presence of potassium carbonate, followed by catalytic reduction with hydrazine and Pd/C. Polyimides were synthesized from diamine 2 and various aromatic dianhydrides 3a–f via thermal imidization. These polymers had inherent viscosities ranging from 0.73 to 1.29 dL/g. Polyimides 5a–f were soluble in amide polar solvents and even in less polar solvents. These films had tensile strengths of 87–100 MPa, elongations to break of 8–29%, and initial moduli of 1.7–2.2 GPa. The glass transition temperatures (T_g) of 5a–f were in the range of 222–271°C, and the 10% weight loss temperatures (T₁₀) of them were all above 493°C. Compared with polyimides 6 series based on 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane (BAPP) and polyimides 7 based on 2,2‐Bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane (6FBAPP), the 5 series showed better solubility and lower color intensity, dielectric constant, and lower moisture absorption. Their films had cutoff wavelengths between 363 and 404 nm, b* values ranging from 8 to 62, dielectric constants of 2.68–3.16 (1 MHz), and moisture absorptions in the range of 0.04–0.35 wt %. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 922–935, 2005     

Preparation and characterization of organosoluble polyimides based on 1,1-bis[4-(3,4-aminophenoxy)phenyl]cyclohexane and commercial aromatic dianhydrides

A bis(ether amine) III-A containing a cyclohexane cardo group, 1,1-bis[4-(4-aminophenoxy)phenyl]cyclohexane, was synthesized and used as a monomer to prepare polyimides VI-A with six commercial dianhydrides via three different procedures. The intermediate poly(amic acid)s had inherent viscosities of 0.83–1.69 dL g⁻¹ and were thermally or chemically converted into polyimides. Polyimides were also prepared by high-temperature direct polymerization in m-cresol and had inherent viscosities higher than the thermally or chemically cyclodehydrated ones. To improve the solubility of polyimides, six copolyimides were also synthesized from bis(ether amine) III-A with a pair of dianhydrides, which contained 3,3′,4,4′-diphenylsulfonetetracarboxylic dianhydride or 4,4′-hexafluoroisopropylidenediphthalic anhydride. Series VI-A polyimides were characterized by the good physical properties of their film-forming ability, thermal stability, and tensile properties. A comparative study of the properties, with the corresponding polyimides derived from 2,2-bis[4-(4-aminophenoxy)phenyl]propane, is also presented. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2750–2759, 2001     

Synthesis and characterization of soluble random copolyimides

Random copolyimides with different proportions of a diamine component were prepared by polymerizing different compositions of diamines with various dianhydrides and imidized thermally to 260°C. The imidization percent of poly(amic acid) was characterized at various temperatures by infrared spectroscopy. The homopolyimide based on bis[4‐(3‐aminophenoxy)phenyl]sulfone and pyromellitic dianhydride was the only one soluble. By changing the compositions of bis[4‐(3‐aminophenoxy)phenyl]sulfone and other diamines with pyromellitic dianhydride in N‐methyl‐2‐pyrrolidone, soluble random copolyimides could be prepared. By random copolymerization, the thermal properties and viscosities of homopolyimide could be controlled. All the soluble polyimides prepared in this work were amorphous because of the lack of stereoregularity. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 272–277, 1999     

Thermostable soluble aromatic poly(amide-imide)s having hexafluoroisopropylidene and ether links in the main chain

An imide-containing dicarboxylic acid, 2,2-bis[4-(4-trimellitimidophenoxy)phenyl]-hexafluoropropane (I), was prepared by the condensation of 2,2-bis[4-(4-aminophenoxy)phenyl]-hexafluoropropane and trimellitic anhydride. A series of new hexafluoroisopropylidene-containing poly(amide-imide)s having inherent viscosities of 0.64–1.44 dL/g were prepared by the direct polycondensation of diimide-diacid I with various long-chain aromatic diamines using triphenyl phosphite and pyridine as condensing agents in N-methyl-2-pyrrolidone in the presence of calcium chloride. Most of the resulting poly(amide-imide)s were noncrystalline and showed good solubility in polar organic solvents. Almost all polymers afforded transparent, flexible, and tough films. The 10 % weight loss temperatures of these polymers were all above 499 °C, and the glass transition temperatures were in the range of 203–277 °C.     

以BAPP为原料的热塑性PI薄膜的合成及性能

以芳香长链二胺2,2-双[4-(4-氨基苯氧基)苯基]丙烷(BAPP)为二胺原料,与最具商业价值的四种酸酐均苯四甲酸二酐(PMDA)、3,3′,4,4′-联苯四酸二酐(BPDA)、3,3′,4,4′-二苯酮四酸二酐(BTDA)、3,3′,4．4′-二苯醚四酸二酐(ODPA)为二酸酐原料,采用二步溶液缩聚法制得了一系列均聚和共聚聚酰亚胺薄膜。利用FTIR表征了聚酰亚胺的结构,并用DSC、TOA、TMA DMA等手段测得了不同聚酰亚胺的Tg、5%与10%热失重温度、线膨胀系数、拉伸强度、断裂延伸率、热压粘接T型剥离强度等性能数据。     

Synthesis and properties of organosoluble polyimides derived from 2,2′‐dibromo‐ and 2,2′,6,6′‐tetrabromo‐4,4′‐oxydianilines

Two new aromatic diamines, 2,2′‐dibromo‐4,4′‐oxydianiline (DB‐ODA 4 ) and 2,2′,6,6′‐tetrabromo‐4,4′‐oxydianiline (TB‐ODA 5 ), have been synthesized by oxidation, bromination, and reduction of 4,4′‐oxydianiline (4,4′‐ODA). Novel polyimides 6a–f and 7a–f were prepared by reacting DB‐ODA ( 4 ) and TB‐ODA ( 5 ) with several dianhydrides by one‐step method, respectively. The inherent viscosities of these polyimides ranged from 0.31 to 0.99 dL/g (0.5 g/dL, in NMP at 30°C). These polyimides showed enhanced solubilities compared to those derived from 4,4′‐oxydianiline and corresponding dianhydrides. Especially, polyimides 7a , derived from rigid PMDA and TB‐ODA ( 5 ) can also be soluble in THF, DMF, DMAc, DMSO, and NMP. These polyimides also exhibited good thermal stability. Their glass transition temperatures measured by thermal mechanical analysis (TMA) ranged from 251 to 328°C. When the same dianhydrides were used, polyimides 7 containing four bromide substituents had higher glass transition temperatures than polyimides 6 containing two bromide substituents. The effects of incorporating more polarizable bromides on the refractive indices of polyimides were also investigated. The average refractive indices (n_av) measured at 633 nm were from 1.6088 to 1.7072, and the in‐plane/out‐of‐plane birefringences (Δn) were from 0.0098 to 0.0445. It was found that the refractive indices are slightly higher when polyimides contain more bromides. However, this effect is not very obvious. It might be due to loose chain packing resulted from bromide substituents at the 2,2′ and 2,2′,6,6′ positions of the oxydiphenylene moieties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Organosoluble, Low-Colored Fluorinated Polyimides Based on 1,1-Bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane

A novel trifluoromethyl-substituted bis(ether amine) monomer, 1,1-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane, was synthesized that led to a series of novel fluorinated polyimides via chemical imidization route when reacted with various commercially available aromatic tetracarboxylic dianhydrides. These polyimides were highly soluble in a variety of organic solvents such as N-methyl-2-pyrrolidone and N,N -dimethylacetamide, and most of them could afford transparent, low-colored, and tough films. These polyimides exhibited glass-transition temperatures (T _gs) of 227–269 °C and showed no significant decomposition below 500 °C under either nitrogen or air atmosphere. These polyimides had low dielectric constants of 2.87–3.17 at 10 kHz, low water uptake of 0.13%–0.58%, and an ultraviolet-visible absorption cutoff wavelength at 364–410 nm. For a comparative study, a series of analogous polyimides based on 1,1-bis[4-(4-aminophenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane were also prepared and characterized.     

Organosoluble and light-colored fluorinated semialicyclic polyimide derived from 1,2,3,4-cyclobutanetetracarboxylic dianhydride

In this study, the alicyclic dianhydrides 1,2,3,4-cyclobutanetetracarboxylic dianhydride (CBDA) was polymerized with seven kinds of fluorinated aromatic diamines, 2,2′-bis(trifluoromethyl)-4,4′-diaminobiphenyl (1), 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene (2), 1,4-bis(4-amino-2-trifluoromethylphenoxy)diphenyl (3), 1,4-bis(4-amino-2-trifluoromethylphenoxy) diphenyl ether (4), 2,2-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]hexafluoropropane (5), 4,4′-bis(4-amino-2-trifluoromethylphenoxy)diphenyl sulfone (6), and 2,7-bis(4-amino-2-trifluoromethylphenoxy)naphthalene (7), via a two-step polycondensation procedure to prepare seven kinds of fluorinated semialicyclic polyimides (PI) PI-1 ∼ PI-7. The structures of these polyimides were confirmed by infrared spectroscopy (IR). Solubility of the polyimides was tested in various organic solvents and their thermal properties were investigated by dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA). Ultraviolet-visible spectra (UV-vis) and near infrared absorption spectra (NIR) were obtained to evaluate the optical properties of these polyimides. The obtained polyimides PI-1 ∼ PI-7 displayed excellent solubility in a variety of organic solvents; they were readily soluble in amide-type polar solvent. These polyimide films exhibited good optical transparency in the visible light region (400–700 nm) with the transmittance higher than 80% at 450 nm, and these polyimide films showed little absorption at the optocommunication wavelengths of 1.30 and 1.55 μm. These polyimides showed good thermal stability with the 10% thermal decomposing temperatures higher than 443°C in nitrogen and the glass transition temperatures higher than 265°C. In addition, the effect of the structure of fluorinated diamines on the properties of polyimide films was also compared. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Resistive switching characteristics of polyimides derived from 2,2′‐aryl substituents tetracarboxylic dianhydrides

2,2′‐Position aryl‐substituted tetracarboxylic dianhydrides including 2,2′‐bis(biphenyl)‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride and 2,2′‐bis[4‐(naphthalen‐1‐yl)phenyl)]‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride were synthesized. A new series of aromatic polyimides (PIs) were synthesized via a two‐step procedure from 3,3′,4,4′‐biphenyl tetracarboxylic dianhydride and the newly synthesized tetracarboxylic dianhydrides monomers reacting with 2,2′‐bis[4′‐(3″,4″,5″‐trifluorophenyl)phenyl]‐4,4′‐biphenyl diamine. The resulting polymers exhibited excellent organosolubility and thermal properties associated with T_g at 264 °C and high initial thermal decomposition temperatures (T_5%) exceeding 500 °C in argon. Moreover, the fabricated sandwich structured memory devices of Al/PI‐a/ITO was determined to present a flash‐type memory behaviour, while Al/PI‐b/ITO and Al/PI‐c/ITO exhibited write‐once read‐many‐times memory capability with different threshold voltages. In addition, Al/polymer/ITO devices showed high stability under a constant stress or continuous read pulse voltage of ? 1.0 V. Copyright © 2011 Society of Chemical Industry     

Synthesis,characterization, and structure-property relationships of aromatic polyimides containing 4,4′-diaminotriphenylmethane

This work reports two series of structurally different aromatic polyimides based on 4,4´-diaminodiphenylmethane (DPM) and 4,4´-diaminotriphenylmethane (TPM) and three commercial dianhydrides. All TPM-based polyimides formed membranes due to their high molecular weight (inherent viscosities ~0.93–1.14 dl/g), they exhibited high thermal stability (5 %: 490–544 °C), glass transition temperatures between 269 and 293 °C, and reasonable mechanical properties. The incorporation of pendant phenyl moieties in the TPM-based polyimides has a strong effect producing an improvement in solubility, thermal stability, density and gas permeability coefficient in comparison with DPM-based polyimides. The most interesting polyimide TPM-6FDA, containing phenyl and trifluoromethyl as bulky pendant groups, showed higher gas permeability coefficient for CO₂ (23.73 Barrer) and the best ideal selectivity to the gas pair CO₂/CH₄ (α = 28.93).     

Synthesis and characterization of novel fluorinated polyimides derived from bis[4-(4′-aminophenoxy)phenyl]-3,5-bis(trifluoromethyl)phenyl phosphine oxide

A novel fluorinated aromatic diamine, bis[4-(4′-aminophenoxy)phenyl]-3,5-bis(trifluoromethyl)phenyl phosphine oxide, was synthesized. A series of new fluorinated polyimides containing phosphine oxide was prepared from the novel diamine with various commercially available aromatic dianhydrides. All the fluorinated polyimides show high glass transition temperatures, excellent thermal stability, and good solubility in common organic solvents.     

Synthesis and characterization of novel polyimides derived from 4,4’-bis(5-amino-2-pyridinoxy)benzophenone: effect of pyridine and ketone units in the main

A diamine monomer, 4,4’-bis(5-amino-2-pyridinoxy)benzophenone, was designed and synthesized, and used to react with commercially different kinds of aromatic dianhydrides to prepare a series of polyimides containing pyridine and ketone units via the classical two-step procedure. Glass transition temperatures (T_g) of the resultant polyimides PI-(1–5) derived from 4,4’-bis(5-amino-2-pyridinoxy) benzophenone with various dianhydrides ranged from 201 to 310 °C measured by differential scanning calorimetry. The temperatures for 5%wt loss of the resultant polyimides in nitrogen atmosphere obtained from the thermogravimetric analysis curves fell in the range of 472–501 °C. The temperatures for 10%wt loss of the resultant polyimides in nitrogen atmosphere fell in the range of 491–537 °C. Meanwhile, the char yields at 800 °C were in the range of 55.3–60.8%. Moreover, the moisture absorption of polyimide films was measured in the range of 0.37–2.09%. The thin films showed outstanding mechanical properties with tensile strengths of 103–145 MPa, an elongation at break of 12.9–15.2%, and a tensile modulus of 1.20–1.88 Gpa, respectively. The coefficients of thermal expansion of the resultant polyimides were obtained among 26–62 ppm °C^?1. To sum up, this series of polyimides had a good combination of properties applied for high-performance materials and showed promising potential applications in the fields of optoelectronic devices.     

Synthesis of some new polyers and copolymers from 2,2-bis (4-chlorophenyl) 1, 1, 1-trichloro ethane (DDT)

DDT (I) was polycondensed with 2,2-bis(4-hydroxy phenyl)- propane (bisphenol-A) to form polyether. The following monomers were synthesised from DDT: 2,2-bis(4-chloro-phenyl)1, 1-dichloroethylene(II), 2,2-bis(3-nitro-4-chlorophenyl)ethane (III) and 2,2-bis (3-nitro-4-chloro-phenylethylene (IV) and polycondensed with bisphenol-A. They were also copolymerised with bis(4-chlorophenyl)sulphone and bisphenol-A in several molar ratios. The polymers and copolymers were characterised by various techniques. The results obtained show that the DDT has a low reactivity, but nitration and dehydrochlorin-ation increases its reactivity to a significant extent.     

Synthesis and characterisation of organosoluble polyimides containing the anisyl moiety

A new type of diamine monomer containing the anisyl moiety was synthesized via a straight‐forward one‐step procedure. Anisaldehyde was reacted with 2,6‐dimethylaniline in the presence of dry HCl to attain bis(4‐amino‐3,5‐dimethylphenyl)anisylmethane. A series of organo‐soluble polyimides were prepared using the anisyl diamine and various aromatic dianhydrides via a two step method involving thermal imidization. All polyimides are soluble in strong polar solvents such as N‐methyl‐2‐pyrollidone, N,N‐Dimethylformamide, and N,N‐DimethylAcetamide. The polyimides show excellent thermal stability and good mechanical properties. The glass transition temperatures of the polyimides are in the range 265–294 °C. The tensile strengths are in the range 79–99 MPa and the temperatures at which 10 % weight loss occurs are in the range 460–496 °C. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of novel soluble pyridine‐containing polyimides based on 4‐phenyl‐2,6‐bis[4‐(4‐aminophenoxy)phenyl]‐pyridine and various aromatic dianhydrides

A new kind of pyridine‐containing aromatic diamine monomer, 4‐phenyl‐2,6‐bis[4‐(4‐aminophenoxy)phenyl]‐pyridine (PAPP), was successfully synthesized by a modified chichibabin reaction of benzaldehyde and a substituted acetophenone, 4‐(4‐nitrophenoxy)‐acetophenone (NPAP), followed by a reduction of the resulting dinitro compound 4‐phenyl‐2,6‐bis[4‐(4‐nitrophenoxy)phenyl]‐pyridine (PNPP) with Pd/C and hydrazine monohydrate. The aromatic diamine was employed to synthesize a series of new pyridine‐containing polyimides by polycondensation with various aromatic dianhydrides in N‐methy‐2‐pyrrolidone (NMP) via the conventional two‐step method, i.e., ring‐opening polycondensation forming the poly (amic acid)s and further thermal or chemical imidization forming polyimides. The inherent viscosities of the resulting polyimides were in the range of 0.79–1.13 dL/g, and most of them were soluble in common organic solvents such as N,N‐dimethylacetamide (DMAc), NMP, and tetrahydrofuran (THF), etc. Meanwhile, strong and flexible polyimide films were obtained, which had good thermal stability, with the glass transition temperatures (T_g) of 268–338°C and the temperature at 5% weight loss of 521–548°C in air atmosphere, as well as outstanding mechanical properties with tensile strengths of 89.2–112.1 MPa and elongations at break of 9.5–15.4%. The polyimides also were found to possess low dielectric constants ranging from 2.53 to 3.11. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 212–219, 2007     

Synthesis and characterization of novel polyesterimides

A series of soluble novel polyesterimides was synthesized from diamines [a mixture of 2,2‐bis(4‐(4‐aminophenoxy)phenyl)propane (BAPP) with amine‐terminated polysiloxane (ATPS) in various mole ratios] and the ester‐group‐containing dianhydrides. The ester group containing dianhydrides in turn was synthesized by the transesterification reaction of trimellitic anhydride (TMA) with diacetate ester of hydroquinone (HQ), 4,4′‐dihydrophenyl (BP), 1,6‐hexanediol, or ethylene glycol. The resulted polyesterimides were characterized by using Fourier‐transform infrared spectroscopy, inherent viscosity, solubility, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The polyesterimides of BP and HQ had relatively high glass transition temperatures in the range of 214.7–227.2 and 195.7–210.5°C, respectively. The glass transitions decreased rather slowly with the increase in polysiloxane content. Thermal stability and the weight‐loss behavior of polyesterimides were studied by TGA. All polyesterimides of BP and HQ (BPI and HQI) showed no significant weight loss below 500°C in a N₂ environment, and the decomposition temperatures (T_d5%) of BPI and HQI were >520°C. Most polyesterimides were soluble in polar aprotic solvents and m‐cresol. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 730–738, 2004     

Preparation and properties of melt‐processable polyimides based on fluorinated aromatic diamines and aromatic dianhydrides

Two series of melt‐processable polyimides were prepared from 4,4′‐bis(3‐amino‐5‐trifluoromethylphenoxy)biphenyl (m‐6FBAB) and 4,4′‐bis(4‐amino‐5‐trifluoromethylphenoxy) biphenyl (p‐6FBAB) with various aromatic dianhydrides. The effects of the chemical structures of the polyimides on their properties, especially the melt processability and organic solubility, were investigated. The experimental results demonstrate that some of the fluorinated aromatic polyimides showed good melt processability at elevated temperatures (250–360°C) with relatively low melt viscosities and could be melt‐molded to produce strong and tough polyimide sheets. Meanwhile, the polyimides showed excellent organic solubility in both polar aprotic solvents and common solvents to give stable polyimide solutions with high polymer concentrations and relatively low viscosities. Thus, we prepared high‐quality polyimide films by casting the polyimide solutions on glass plates followed by baking at relatively low temperatures. The polyimides derived from m‐6FBAB showed better melt processability and solubility than the p‐6FBAB based polymers. The melt‐processable polyimides showed a good combination of thermal stability and mechanical properties, with decomposition temperatures of 547–597°C, glass‐transition temperatures in the range 205–264°C, tensile strengths of 81.3–104.9 MPa, and elongations at break as high as 19.6%. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and properties of polyimide‐g‐nylon 6 and nylon 6‐b‐polyimide‐b‐nylon 6 copolymers

Polyimide‐g‐nylon 6 copolymers were prepared by the polymerization of phenyl 3,5‐diaminobenzoate with several diamines and dianhydrides with a one‐step method. The polyimides containing pendant ester moieties were then used as activators for the anionic polymerization of molten ε‐caprolactam. Nylon 6‐b‐polyimide‐b‐nylon 6 copolymers were prepared by the use of phenyl 4‐aminobenzoate as an end‐capping agent in the preparation of a series of imide oligomers. The oligomers were then used to activate the anionic polymerization of ε‐caprolactam. In both the graft and copolymer syntheses, the phenyl ester groups reacted quickly with caprolactam anions at 120°C to generate N‐acyllactam moieties, which activated the anionic polymerization. All the block copolymers had higher moduli and tensile strengths than those of nylon 6. However, their elongations at break were much lower. The graft copolymers based on 2,2′‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]propane dianhydride and 2,2′‐bis[4‐(4‐aminophenoxy)phenyl]propane displayed elongations comparable to that of nylon 6 and the highest moduli and tensile strengths of all the copolymers. The thermal stability, moisture resistance, and impact strength were dramatically increased by the incorporation of only 5 wt % polyimide into both the graft and block copolymers. The graft and block copolymers also exhibited improved melt processability. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 300–308, 2006     

Synthesis and properties of fluorinated bis‐benzocyclobutene‐terminated arylene ether monomers

Four novel bis‐benzocyclobutene‐endcapped arylene ether monomers, 1,1′‐bis[4‐(4′‐benzocyclobutenyloxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane (BOPP3FE), 1,1′‐bis[4‐(4′‐benzocyclobutenyloxy)phenyl]‐1‐(3′,5′‐ditrifluoromethyl)phenyl‐2,2,2‐trifluoroethane(BOPP9FE), 2,2′‐bis[4‐(4′‐benzocyclobutenyloxy)phenyl]‐1,1,1,3,3,3‐hexfluoropropane (BOP6FP), and 2,2′‐bis[4‐(4′‐benzocyclobutenyloxy)phenyl]‐propane (BOPP) were prepared and characterized. All the four monomers showed similar curing behaviors under N₂ (Differential scanning calorimetry: extrapolated onset and peak temperatures at 225–229°C and 261–263°C) and demonstrated low and steady melt viscosities between 110 and 200°C, indicating their good processability. After cure, the resulting BCB resins exhibited high T_g (232–282°C) and excellent thermal stability (T_5% > 433°C). The resins also showed good mechanical properties with the flexural strengths of 68–88 MPa and the flexural modulus of 2.52–3.15 GPa. Moreover, the resins also exhibited low dielectric constants (2.58–2.88), low dissipation factors (2.7 to 8.4 × 10?4) and low water absorptions in boiling water for 24 h (0.29–0.59%). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009