Synthesis of branched poly(lactide) using polyglycidol and thermal, mechanical properties of its solution-cast film

Branched poly(lactide)(PLA)s with various lengths of graft chain were synthesized by ring-opening polymerization of l- or d-lactide (l- or d-LA) in bulk using polyglycidol as a macroinitiator. The properties of polymer films of branched PLLA or PDLA obtained and their stereocomplex were investigated through thermal analysis and tensile testing. The branched PLLA or PDLA film exhibited a lower glass transition temperature (T_g), melting temperature (T_m), crystallinity, Young's modulus and a higher strain at break than the corresponding linear PLLA or PDLA film. The branched PLLA/branched PDLA stereocomplex film showed a high maximum stress and a high Young's modulus keeping its high strain at break. Moreover, the usefulness of branched PLLA or PDLA as a plasticizer of linear PLLA was investigated with 1:9 blend or stereocomplex film prepared from the branched PLLA or branched PDLA and linear PLLA. The blend or linear PLLA/branched PDLA stereocomplex film showed a higher strain at break compared with linear PLLA film. The mechanical properties of the blend or linear PLLA/branched PDLA stereocomplex film could easily be controlled by changing the molecular weight of branched PLA.     

Blends of aliphatic polyesters. II. Hydrolysis of solution-cast blends from poly(L-lactide) and poly(E-caprolactone) in phosphate-buffered solution

Blend films were prepared from poly(L -lactide) (PLLA) and poly(E-caprolactone) (PCL) with different PLLA contents [X_PLLA (w/w) = PLLA/(PCL + PLLA)] by the solution-casting method and their hydrolysis behaviors were investigated up to 20 months in a phosphate-buffered solution of pH 7.4 at 37°C by gel permeation chromatography, tensile testing, differential scanning calorimetry, and gravimetry. Polarizing microscopic observation and dynamic mechanical analysis revealed that PCL and PLLA were phase-separated in blend films before hydrolysis. The mass remaining, molecular weight, and tensile strength of the blend films with X_PLLA of 0.5 and 0.75 decreased more rapidly by hydrolysis than those of the nonblended PLLA, while the elongation at break of the blend film of X_PLLA = 0.25 decreased the slowest. The rate constant for hydrolysis (k) calculated from the M_n change during hydrolysis was higher for blend films of X_PLLA = 0.5 and 0.75 than those expected from k of nonblended PLLA and PCL. The melting temperature (T_m) of PLLA in the blend and nonblended films of X_PLLA = 0.5, 0.75, and 1 decreased from 179 to 161, 160, and 175°C upon hydrolysis for 20 months, respectively, while that for X_PLLA = 0.25 slightly increased from 176 to 177°C. On the other hand, T_m and the crystallinity of PCL was significantly increased by hydrolysis for 20 months, irrespective of X_PLLA. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 405–415, 1998     

Aging of poly(lactide)/poly(ethylene glycol) blends. Part 2. Poly(lactide) with high stereoregularity

Blending poly(ethylene glycol) (PEG) with poly(lactide) (PLA) decreases the T_g and improves the mechanical properties. The blends have lower modulus and increased fracture strain compared to PLA. However, the blends become increasingly rigid over time at ambient conditions. Previously, it was demonstrated that a PLA of lower stereoregularity was miscible with up to 30 wt% PEG. Aging was due to slow crystallization of PEG from the homogeneous amorphous blend. Crystallization of PEG depleted the amorphous phase of PEG and gradually increased the T_g until aging essentially ceased when T_g of the amorphous phase reached the aging temperature. In the present study, this aging mechanism was tested with a crystallizable PLA of higher stereoregularity. Changes in thermal transitions, solid state structure, and mechanical properties were examined over time. Blends with up to 20 wt% PEG were miscible. Blends with 30 wt% PEG could be quenched from the melt to the homogenous amorphous glass. However, this composition phase separated at ambient temperature with little or no crystallization. Changes in mechanical properties during phase separation reflected increasing rigidity of the continuous PLA-rich phase as it became richer in PLA. Construction of a phase diagram for blends of higher stereoregular PLA with PEG was attempted.     

Aging of poly(lactide)/poly(ethylene glycol) blends. Part 1. Poly(lactide) with low stereoregularity

Poly(lactide) (PLA) is rapidly gaining interest as a biodegradable thermoplastic for general usage in degradable disposables. To improve mechanical properties, a PLA with low stereoregularity was blended with polyethylene glycol (PEG). Blends with up to 30 wt% PEG were miscible at ambient temperature. Blending with PEG significantly decreased the T_g, decreased the modulus and increased the fracture strain of PLA. However, the PLA/PEG 70/30 blend became increasingly rigid over time at ambient conditions. The mechanism of aging primarily under ambient conditions of temperature and humidity was studied. Changes in mechanical properties, thermal transitions and solid state morphology were examined over time. Aging was caused by slow crystallization of PEG. Crystallization of PEG depleted the amorphous phase of PEG and gradually increased the T_g. As T_g approached the aging temperature, reduced molecular diffusivity slowed the crystallization rate dramatically. Aging essentially ceased when T_g of the amorphous phase reached the aging temperature. The increase in matrix T_g and the reinforcing effect of the crystals produced a change in mechanical properties from elastomer-like to thermoplastic-like.     

Crystallization and phase separation in blends of high stereoregular poly(lactide) with poly(ethylene glycol)

The effect of cooling rate on crystallization and subsequent aging of high stereoregular poly(lactide) (PLA) blended with poly(ethylene glycol) (PEG) was studied by thermal analysis and by direct observation of the solid state structure with atomic force microscopy (AFM). Blending with PEG accelerated crystallization of PLA. When a PLA/PEG 70/30 (wt/wt) blend was slowly cooled from the melt, PLA crystallized first as large spherulites followed by crystallization of PEG. The extent of PLA crystallization depended on the cooling rate, however, for a given blend composition the PEG crystallinity was proportional to PLA crystallinity. The partially crystallized blend obtained with a cooling rate of 30 °C min⁻¹ consisted of large spherulites dispersed in a homogeneous matrix. The blend was not stable at ambient temperature. With time, epitaxial crystallization of PEG on the edges of the spherulites depleted the surrounding region of PEG, which created a vitrified region surrounding the spherulites. Further from the spherulites, the homogeneous amorphous phase underwent phase separation with formation of a more rigid PLA-rich phase and a less-rigid PEG-rich phase. Decreasing the amount of PEG in the blend decreased the crystallization rate of PLA and increased the nucleation density. The amount of PLA crystallinity did not depend on blend composition, however, PEG crystallinity decreased to the extent that PEG did not crystallize in a PLA/PEG 90/10 (wt/wt) blend.     

Porous biodegradable polyesters. I. Preparation of porous poly(L‐lactide) films by extraction of poly(ethylene oxide) from their blends

Porous poly(L ‐lactide) (PLLA) films were prepared by water extraction of poly(ethylene oxide) (PEO) from solution‐cast PLLA and PEO blend films. The dependence of blend ratio and molecular weight of PEO on the porosity and pore size of films was investigated by gravimetry and scanning electron microscopy. The film porosity and extracted weight ratio were in good agreement with the expected for porous films prepared using PEO of low molecular weight (M_w = 1 × 10³), but shifted to lower values than expected when high molecular weight PEO (M_w = 1 × 10⁵) was utilized. The maximum pore size was larger for porous films prepared from PEO having higher molecular weight, when compared at the same blending ratio of PLLA and PEO before water extraction. Differential scanning calorimetry of as‐cast PLLA and PEO blend films revealed that PLLA and PEO were phase‐separated at least after solvent evaporation. On the other hand, comparison of blend films before and after extraction suggested that a small amount of PEO was trapped in the amorphous region between PLLA crystallites even after water extraction and hindered PLLA crystallization during solvent evaporation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 629–637, 2000     

Miscibility,morphology and thermal properties of poly(para‐dioxanone)/poly(D,L‐lactide) blends

BACKGROUND: Poly(para‐dioxanone) (PPDO) is a biodegradable polyester with excellent biodegradability, bioabsorbability, biocompatibility and mechanical flexibility. However, its high cost and relatively fast degradation rate have hindered the development of commercial applications. Blending with other polymers is a simple and convenient way of modifying the properties of aliphatic polyesters. Poly(D ,L ‐lactide) (PDLLA) is another polyester that has been extensively studied for biomedical applications due to its biocompatibility and suitable degradation rate. However, to our knowledge, blends of PPDO/PDLLA have not been reported in the literature. RESULTS: A series of biodegradable polymers were blended by solution co‐precipitation of PPDO and PDLLA in various blend ratios. The miscibility, morphology and thermal properties of the materials were investigated. DSC curves for all blends revealed two discrete glass transition temperatures which matched the values for pure PPDO and PDLLA. SEM images of fracture surfaces displayed evidence of phase separation consistent with the DSC results. The contact angles increased with the addition of PDLLA. CONCLUSION: PPDO/PDLLA blends exhibit two distinct glass transition temperatures that remain nearly constant and correspond to the glass transition temperatures of the homopolymers for all blend compositions, indicating that blends of PPDO and PDLLA are immiscible. Images of the surface obtained using SEM were also suggestive of a two‐phase material. The crystallinity of the PPDO phase in the blends was affected by the PDLLA content. The mechanical properties of the blends changed dramatically with composition. Adding PDLLA makes the blends less hydrophilic than PPDO. Copyright © 2008 Society of Chemical Industry     

Crystallization, spherulite growth, and structure of blends of crystalline and amorphous poly(lactide)s

The effects of incorporated amorphous poly(dl-lactide) (PDLLA) on the isothermal crystallization and spherulite growth of crystalline poly(l-lactide) (PLLA) and the structure of the PLLA/PDLLA blends were investigated in the crystallization temperature (T_c) range of 90-150 °C. The differential scanning calorimetry results indicated that PLLA and PDLLA were phase-separated during crystallization. The small-angle X-ray scattering results revealed that for T_c of 130 °C, the long period associated with the lamellae stacks and the mean lamellar thickness values of pure PLLA and PLLA/PDLLA blend films did not depend on the PDLLA content. This finding is indicative of the fact that the coexisting PDLLA should have been excluded from the PLLA lamellae and inter-lamella regions during crystallization. The decrease in the spherulite growth rate and the increase in the disorder of spherulite morphology with an increase in PDLLA content strongly suggest that the presence of a very small amount of PDLLA chains in PLLA-rich phase disturbed the diffusion of PLLA chains to the growth sites of crystallites and the lamella orientation. However, the wide-angle X-ray scattering analysis indicated that the crystalline form of PLLA remained unvaried in the presence of PDLLA.     

Blends of phenolphthalein poly(ether ether ketone) and a thermotropic liquid crystalline copolyester

Blends of phenolphthalein poly(ether ether ketone) (PEK-C) and a thermotropic liquid crystalline copolyester (LCP), poly[(1-phenylethyl-p-phenylene terephthalate)-co-(1-cumyl-p-phenylene terephthalate)], was prepared via melt mixing. The studies of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) indicate that the PEK-C/LCP blends display two glass transition temperatures which correspond to those of PEK-C- and LCP-rich phases, respectively. The PEK-C/LCP blends were judged to be partially miscible. Scanning electron microscopy (SEM) was employed to examine the morphology of the blends, and it was observed that all the PEK-C/LCP blends displayed a phase-separated structure. The interface between the PEK-C- and LCP-rich phases is poor. The Young's modulus of the PEK-C/LCP blends was found to increase with LCP content due to the high modulus of the LCP. However, the tensile strength and the elongation at break of the blends greatly decreases with increase of LCP content, owing to the poor interfacial adhesion. From the thermogravity analysis (TGA), it was observed that all the blends exhibited a two-step weight loss mechanism, and the thermal degradation onset temperature of the blends was lowered with the addition of LCP content. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1923–1931, 1998     

Properties and Biodegradability of Polymer Blends of Poly(L‐lactide)s with Different Optical Purity of the Lactate Units

Polylactides with high and low L ‐isomeric ratios of the lactate units (PLA99.0 and 77.0, where the numbers correspond to the L ‐ratios) were melt‐blended to analyze the changes in properties and biodegradability with the polymer blend. The crystallinity of the blends was almost similar to that of the blends of PLLA and PDLLA. The glass transition behavior supported the compatibility of both polymers. The glass transition behavior was indicative of a compatible nature of both polymers. The tensile modulus of the blends was almost identical irrespectively of the blend ratio, while their tensile strength decreased with decreasing composition of PLA99.0. Above T_g, the storage modulus of the blends dropped from 2–3×10⁹ Pa to 1–3×10⁶ Pa and then increased to a different level depending on the crystalline nature of the blends. The biodegradability of the blends increased with decreasing composition of PLA99.0. This difference in degradability can be well explained by our random packing model of local helices of the L ‐sequenced chains for the L ‐rich PLA samples.     

Blends of aliphatic polyesters. III. Biodegradation of solution-cast blends from poly(L-lactide) and poly(ε-caprolactone)

Phase-separated blend films were prepared with the solution casting method from poly(L -lactide) (PLLA) and poly(ε-caprolactone) (PCL) with different PLLA contents [X_PLLA (w/w) = PLLA/(PCL + PLLA)] and their biodegradation was investigated in soil up to 20 months by gravimetry, gel permeation chromatography, tensile testing, differential scanning calorimetry, and scanning electron microscopy. The nonblended PCL film and the blend film with X_PLLA = 0.25 disappeared in 4 and 12 months, respectively, while most of the initial mass remained for the blend film of X_PLLA = 0.75 and the nonblended PLLA film. The decrease in weight remaining, molecular weight, tensile strength, and elongation-at-break was higher for blend films of low X_PLLA. The melting temperature of PLLA in blend films of X_PLLA = 0.5 and 0.75, and of nonblended film, remained around 179°C upon biodegradation in soil for 20 months. The preferred biodegradation of PCL in blend films resulted in formation of microspheres of a PLLA-rich phase at the surface for the blend film of X_PLLA = 0.25 and the porous structure for blend films of X_PLLA = 0.5 and 0.75. Comparison of the weight loss of blend films in biodegradation in soil with that of the nonenzymatic hydrolysis in phosphate-buffered solution revealed preferred enzymatic degradation of PCL and insignificant attack to PLLA in the blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2259–2268, 1998     

Miscibility and phase structure of binary blends of poly(L‐lactide) and poly(vinyl alcohol)

Blend films of poly(L ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA) were obtained by evaporation of hexafluoroisopropanol solutions of both components. The component interaction, crystallization behavior, and miscibility of these blends were studied by solid‐state NMR and other conventional methods, such as Fourier transform infrared (FTIR) spectra, differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction (WAXD). The existence of two series of isolated and constant glass‐transition temperatures (T_g's) independent of the blend composition indicates that PLLA and PVA are immiscible in the amorphous region. However, the DSC data still demonstrates that some degree of compatibility related to blend composition exists in both PLLA/atactic‐PVA (a‐PVA) and PLLA/syndiotactic‐PVA (s‐PVA) blend systems. Furthermore, the formation of interpolymer hydrogen bonding in the amorphous region, which is regarded as the driving force leading to some degree of component compatibility in these immiscible systems, is confirmed by FTIR and further analyzed by ¹³C solid‐state NMR analyses, especially for the blends with low PLLA contents. Although the crystallization kinetics of one component (especially PVA) were affected by another component, WAXD measurement shows that these blends still possess two isolated crystalline PLLA and PVA phases other than the so‐called cocrystalline phase. ¹³C solid‐state NMR analysis excludes the interpolymer hydrogen bonding in the crystalline region. The mechanical properties (tensile strength and elongation at break) of blend films are consistent with the immiscible but somewhat compatible nature of these blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 762–772, 2001     

Preparation of poly(L‐lactide) film having high elastic recovery

Triacetin (TAC) is known as a lubricant of poly(L ‐lactide) (PLLA), and it is used to improve the mechanical properties of PLLA. However, the compatibility of TAC with PLLA and the morphological changes induced by the addition of TAC to PLLA have not been clarified. This study investigates the effects of the addition of TAC on the morphological changes and physical properties of PLLA. We prepared the PLLA films containing a given amount of TAC by solvent‐cast blending with chloroform under a low temperature. From the investigation of the mechanical properties of the blends, it is found that the glass‐transition temperature of PLLA is remarkably decreased with an increasing amount of TAC, the blend films exhibit high elastic recovery, and the degree of the recovery increases linearly with the amount of TAC. The morphological changes exhibiting high elastic recovery are discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 474–480, 2003     

Blends of poly(ethylene terephthalate) and poly(butylene terephthalate)

Commercial grade poly(ethylene terephthalate), (PET, intrinsic viscosity = 0.80 dL/g) and poly(butylene terephthalate), (PBT, intrinsic viscosity = 1.00 dL/g) were melt blended over the entire composition range using a counterrotating twin‐screw extruder. The mechanical, thermal, electrical, and rheological properties of the blends were studied. All of the blends showed higher impact properties than that of PET or PBT. The 50:50 blend composition exhibited the highest impact value. Other mechanical properties also showed similar trends for blends of this composition. The addition of PBT increased the processability of PET. Differential scanning calorimetry data showed the presence of both phases. For all blends, only a single glass‐transition temperature was observed. The melting characteristics of one phase were influenced by the presence of the other. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 75–82, 2005     

Melt characteristics,mechanical, and thermal properties of blown film from modified blends of poly(butylene adipate‐co‐terephthalate) and poly(lactide)

Blown films from poly(butylene adipate‐co‐terephthalate) and poly(lactide) (PLA) blends were investigated. The blends were prepared in a twin‐screw extruder, in the presence of small amounts of dicumyl peroxide (DCP). The influence of DCP concentration on film blowing, rheological, mechanical, and thermal properties of the blends is reported in this article. Rheological results showed a marked increase in polymer melt strength and elasticity with the addition of DCP. As a consequence, the film homogeneity and the stability of the bubble were improved. The modified blend films, compared with the unmodified blend, showed an improvement in tensile strength and modulus with a slight loss in elongation. Fourier transform infrared and gel results revealed that chain scission and branching were more significant than crosslinking when the DCP loadings in the blends were not higher than 0.7%. A reduction in melt temperatures of PLA was observed due to difficulty in chain crystallization. The concentrations of DCP strongly affected the melting temperatures but had an insignificant effect on the decomposition behavior of the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology,crystallization and enzymatic hydrolysis of poly(L‐lactide) nucleated using layered metal phosphonates

Poly(L ‐lactide) (PLLA) was prepared via melt blending and nucleated using three layered metal phosphonates, i.e. zinc phenylphosphonate (PPZn), calcium phenylphosphonate (PPCa) and barium phenylphosphonate (PPBa). The morphology, crystallization and enzymatic hydrolysis of PLLA nucleated using PPZn, PPCa and PPBa were investigated. The results of both wide‐angle X‐ray diffraction and transmission electron microscopy observations show that the layers of PPZn, PPCa or PPBa are barely exfoliated or intercalated by PLLA chains in the melt‐blending process. PPZn, PPCa and PPBa serve as effective nucleating agents, accelerating both non‐isothermal and isothermal crystallization and enzymatic hydrolysis of PLLA. An interesting aspect is that the nucleating ability of PLLA incorporating PPZn, PPCa and PPBa decreases in the order PPZn > PPCa > PPBa, whereas the enzymatic hydrolysis of PLLA incorporating PPZn, PPCa and PPBa decreases in the reverse order, which is due to the different dispersion and interfacial interactions of PPZn, PPCa and PPBa throughout the PLLA matrix. Copyright © 2010 Society of Chemical Industry     

High-Impact PLA in Compatibilized PLA/PCL Blends: Optimization of Blend Composition and Type and Content of Compatibilizer

In this work, the effectiveness of seven commercial compatibilizers is tested in polylactide (PLA)/poly(ε-caprolactone) (PCL) blends with different compositions to obtain a high-impact PLA. None of the compatibilizers is effective for 90/10 and 80/20 PLA/PCL compositions, as no improvement of the impact strength is observed. For the 70/30 composition, compatibilizers having glycidyl methacrylate (GMA) and acrylate groups in their structure are proved the most effective, as the morphological change towards co-continuity induced by them leads to significant impact strength improvements (of ≈345% and 90% with respect to the neat PLA and the noncompatibilized PLA/PCL 70/30 blend, respectively). The 70/30 PLA/PCL composition, as it shows the best balance of properties, and the best compatibilizer (ElvaloyPTW) are chosen to carry out the optimization of the compatibilizer content. It is found that adding 6 phr to the blend results in highly toughened and ductile blends while maintaining a high modulus and yield strength values. Larger compatibilizer contents lead to even higher impact strength values, but the low-strain mechanical properties are notably reduced. Thus, in this work, a simple and easily scalable method to produce high-impact PLA is shown, as it implies the compounding of three commercially available components without involving any toxic solvents.     

Blends of poly(vinyl chloride) with acrylonitrile-chlorinated polyethylene-styrene copolymer. II. Mechanical properties

Blends of poly(vinyl chloride) (PVC) and acrylonitrile-chlorinated polyethylene-styrene (ACS) graft copolymer were prepared by melt blending. Mechanical properties were studied by the use of dynamic mechanical analysis (DMA), impact tests, tensile tests, and scanning electron microscopy (SEM). The DMA study showed that PVC is immiscible with chlorinated polyethylene in ACS but partially miscible with poly(styrene-co-acrylonitrile) (25% acrylonitrile content) in ACS. Mechanical property tests showed that there is a significant increase in the impact strength while other good mechanical properties of PVC such as high modulus and high strength remain. SEM observations supported the results of the mechanical properties studies. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 399–405, 1997     

Poly(D,L‐lactide‐co‐glycolide)/poly(ethylenimine) blend matrix system for pH sensitive drug delivery

Poly(D ,L ‐lactide‐co‐glycolide) (PLGA) and poly(ethylenimine) (PEI) were blended and found to form a homogeneous pH sensitive matrix for drug release. Differential scanning calorimetry (DSC) studies of the PLGA/PEI blends showed a single glass transition temperature at all compositions. Fourier transform infrared spectroscopy (FTIR) demonstrated that the PLGA carbonyl peak at 1760 cm^?1 shifted to 1666 cm^?1 as a result of amide bond formation between the two polymers. This was confirmed by ¹³C nuclear magnetic resonance studies. A PLGA/PEI matrix of 90/10 weight ratio was chosen for evaluation for controlled drug release. Both hydrophobic β‐lapachone and hydrophilic rhodamine B showed pH dependent release profiles with faster release kinetics at lower pH values. The observed pH sensitive drug release was mainly attributed to two factors, pH dependent swelling and protonation of the PEI‐PLGA matrix. These results demonstrate utility of a PLGA/PEI matrix and its potential application in pH responsive drug delivery. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 89–96, 2006     

Characterization of biodegradable polymers by inverse gas chromatography. III. Blends of amylopectin and poly(L‐lactide)

The morphology changes and surface thermodynamics of blends of amylopectin (AP)–poly(L ‐lactide) (PLA) were investigated over a wide range of temperatures and compositions using the inverse gas chromatography method. Twenty‐five solutes were selected such as alkanes, acetates, oxy, halogenated, and six‐member ring families. They provided a variety of specific interactions with the blends' surface. The morphology showed two regions, some others showed a de‐polymerization above 130°C. These zones enabled the estimation of T_g and T_m of AP, PLA, and the blends. Blending AP with PLA caused a decrease in AP's T_g value due to the reduction of the degree of crystallinity of the blend. Exothermic values of χ₂₃ were obtained indicating the compatibility of AP and PLA at all temperatures and weight fractions of AP–PLA. The miscibility was favored at 75%AP, only 25%AP–75%PLA composition influenced the degree of crystallinity. The dispersive component of the surface energy of the blends ranged from 16.09 mJ/m² for the pure AP as high as 58.36 mJ/m² at 110°C when AP was mixed with PLA in a 50–50% ratio. The surface energy was at its highest value when the composition was 75% of AP, in good agreement with χ₂₃ values. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012