Water–alcohol separation by pervaporation through zeolite‐modified poly(amidesulfonamide)

Pervaporation membranes were fabricated by blending different amount of zeolite NaA or NaX with three types of poly(amidesulfonamide) (PASA). The zeolite‐filled membranes were characterized by IR spectroscopy, SEM, sorption measurements, and wide‐angle X‐ray diffraction. By adding the proper amount of NaA into the polymer casting solutions, the resultant zeolite‐filled membranes exhibited improvement in both selectivity and permeability in the separation of 10% aqueous solutions of ethanol and propan‐1‐ol, as compared with the zeolite free membrane. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1323–1329, 2001     

Pervaporation separation of water–isopropanol mixture using carboxymethylated poly(vinyl alcohol) composite membranes

The pervaporation separation of water–isopropanol mixtures was carried out using carboxymethylated poly(vinyl alcohol) (CMPVA) composite membranes. Carboxymethylated PVA (CMPVA) was synthesized by reacting PVA with various concentrations of monochloroacetic acid. Substitution efficiency of the CMPVA ranged from 12–32%. The cross‐sectional structure of the composite membrane for pervaporation was confirmed by scanning electron microscopy (SEM) exhibiting a 20‐μm active skin layer. Glass transition temperature of the CMPVA was in the range of 74–84°C, and decreased with increasing substitution efficiency. Degree of swelling and permeation flux for water–isopropanol in pervaporation increased with the substitution degree of carboxymethylation. CMPVA composite membrane, having 16% substitution efficiency, showed the following pervaporation performance; permeation flux of 831 g/m² h and separation factor of 362 measured at 80°C and 85 wt % feed isopropanol concentration. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 241–249, 1999     

Synthesis,characterization, and pervaporation performance of random copolymers of poly(amidesulfonamide)s (PASAs)

Stimulated by the outstanding membrane properties of poly(amidesulfonamide)s (PASAs), 2 series of copolymers were synthesized by low-temperature solution polycondensation of either the diamino monomer N,N′-bis(4-aminophenylsulfonyl)piperazine (1A) or N,N′-bis(4-aminophenylsulfonyl)-2,5-dimethylpiperazine (1B) with a mixture of isophthaloyl and terephthaloyl chloride. All of these copolymers were adequately characterized by intrinsic viscosity measurements, infrared (IR) spectroscopy, ¹H and ¹³C nuclear magnetic resonance, differential scanning calorimetry, thermogravimetric analysis, and wide-angle X-ray diffraction. The effects of various feed ratios of isophthaloyl–terephthaloyl chloride on the physical properties of the copolymers were investigated. In particular, the crystallinity of PASA copolymers was found to be trimmed down by copolymerizing diamino monomer 1A or 1B with increasing fraction of isophthaloyl chloride. It was envisioned that when the crystallinity of the PASA membranes decreased, permeation flux would be preferably increased at a minimum sacrifice of separation characteristics in the pervaporation process. Experimental findings, however, revealed that the resulting permeation flux and separation factor of pervaporation membranes derived from various copolymers were both within the same order of magnitude. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 47–60, 1998     

Pervaporation separation of water/alcohol mixtures through hydroxypropylated chitosan membranes

The present study investigated the pervaporation performance of novel hydroxypropylated chitosan (HPCS) membranes to separate water from an aqueous alcohol solution. Hydroxypropylated chitosan was prepared from the reaction of chitosan and propylene oxide. The results show that the separation factor decreases and the flux increases with increasing of the substitution degree of the hydroxypropylated chitosan membrane. Crosslinking with glutaraldehyde or treatment with Cu²⁺ can improve the pervaporation performance of modified chitosan membrane grately. The performance data indicate that the crosslinking hydroxypropylated chitosan membrane treated with Cu²⁺ is an excellent pervaporation membrane for the separation of alcohol–water mixtures, and one-stage separation is attainable for some alcohol–water mixtures such as an n-propanol–water and an isopropanol–water system, which has a good separation factor of 220 for the n-PrOH/water system and 240 for the i-PrOH/water system using 85 wt % alcohol concentration at 60°C. The flux for both cases is around 0.5 kg m⁻² h⁻¹. At the same time, the structure of the chemically modified chitosan membranes and their separation characteristics for aqueous alcohol solutions are also discussed. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2035–2041, 1998     

Separation characteristics of pervaporation membrane separation processes using modified poly(vinyl alcohol) membranes

Modified poly(vinyl alcohol) (PVA) membranes prepared by the ‘solution technique’ were tested for ethanol-water mixtures by varying the reaction density (X_cr = 0.05, 0.1) at various temperatures. The results are compared with those of PVA membranes (X_cr = 0.05) prepared by the technique of the GFT Company, Germany.     

Modification of poly(vinyl alcohol) membranes using sulfur-succinic acid and its application to pervaporation separation of water–alcohol mixtures

For the purposes of the water-selective membrane material development for pervaporation separation, we crosslinked poly(vinyl alcohol) (PVA) with sulfur-succinic acid (SSA), which contains —SO₃OH, by heat treatment and investigated the effect of the crosslinking density on the separation of water–alcohol mixtures by pervaporation technique. The crosslinking reaction between PVA and SSA was characterized through Fourier transform infrared spectroscopy and differential scanning calorimetry tests by varying the amount of the crosslinking agent, the reaction temperature, and the swelling measurements of each pure component. The separation performance of the water–methanol mixture is not good due to the existence of sulfonic acid, hydrophilic group, in the crosslinking agent. However, for the water–ethanol mixture, the flux of 0.291 kg/m²h and the separation factor of 171 were obtained at 70°C when PVA-crosslinked membrane containing 7 wt % SSA was used. The same membrane also showed flux of 0.206 kg/m²h and a separation factor of 1969 at the same operating temperature. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1717–1723, 1998     

Synthesis of graft copolymeric membranes of poly(vinyl alcohol) and polyacrylamide for the pervaporation separation of water/acetic acid mixtures

Graft copolymers of poly(vinyl alcohol) (PVA) with polyacrylamide were prepared and membranes were fabricated at 48 and 93% grafting of acrylamide onto PVA. These membranes were used in the pervaporation separation of water/acetic acid mixtures at 25, 35, and 45°C. The permeation flux, separation selectivity, diffusion coefficient, and permeate concentration were determined. The highest separation selectivity of 23 for neat PVA at 25°C and the lowest value of 2.2 for 93% acrylamide‐grafted PVA membranes were observed. A permeation flux of 1.94 kg m^?2 h^?1 was found for the 93% grafted membrane at 90 mass % of water in the feed mixture. The diffusion coefficients in a water/acetic acid mixture had an effect on the membrane permselectivity. The Arrhenius equation was used to calculate the activation parameters for permeation as well as for the diffusion of water and of acetic acid. The activation energy values for the permeation flux varied from 97 to 28 kJ/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 244–258, 2002     

Synthesis,characterization, and pervaporation properties of segmented poly(urethane‐urea)s

Poly(urethane‐urea)s (PUUs) from 2,4‐tolylene diisocyanate (2,4‐TDI), poly(oxytetramethylene)diols (PTMO) or poly(butylene adipate)diol (PBA), and various diamines were synthesized and characterized by Fourier transform infrared spectroscopy, gel permeation chromatography, differential scanning calorimetry, and density measurements. Transport properties of the dense PUU‐based membranes were investigated in the pervaporation of benzene–cyclohexane mixtures. It was shown that the pervaporation characteristics of the prepared membranes depend on the structure and length of the PUU segments. The PBA‐based PUUs exhibit good pervaporation performance along with a very good durability in separation of the azeotropic benzene–cyclohexane mixture. They are characterized by the flux value of 25.5 (kg μm m⁻² h⁻¹) and the separation factor of 5.8 at 25°C, which is a reasonable compromise between the both transport parameters. The PTMO‐based PUUs display high permeation flux and low selectivity in separation of the benzene‐rich mixtures. At the feed composition of 5% benzene in cyclohexane, their selectivity and flux are in the range of 3.2 to 11.7 and 0.4 to 40.3, respectively, depending on the length of the hard and soft segments. The chemical constitution of the hard segments resulting from the chain extender used does not affect the selectivity of the PUU membranes. It enables, however, the permeability of the membranes to be tailored. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1615–1625, 1999     

Polyvinyl alcohol/polysulfone (PVA/PSF) hollow fiber composite membranes for pervaporation separation of ethanol/water solution

Polysulfone (PSF) hollow fiber membranes were spun by phase‐inversion method from 29 wt % solids of 29 : 65 : 6 PSF/NMP/glycerol and 29 : 64 : 7 PSF/DMAc/glycol using 93.5 : 6.5 NMP/water and 94.5 : 5.5 DMAc/water as bore fluids, respectively, while the external coagulant was water. Polyvinyl alcohol/polysulfone (PVA/PSF) hollow fiber composite membranes were prepared after PSF hollow fiber membranes were coated using different PVA aqueous solutions, which were composed of PVA, fatty alcohol polyoxyethylene ether (AEO₉), maleic acid (MAC), and water. Two coating methods (dip coating and vacuum coating) and different heat treatments were discussed. The effects of hollow fiber membrane treatment methods, membrane structures, ethanol solution temperatures, and MAC/PVA ratios on the pervaporation performance of 95 wt % ethanol/water solution were studied. Using the vacuum‐coating method, the suitable MAC/PVA ratio was 0.3 for the preparation of PVA/PSF hollow fiber composite membrane with the sponge‐like membrane structure. Its pervaporation performance was as follows: separation factor (α) was 185 while permeation flux (J) was 30g/m²·h at 50°C. Based on the experimental results, it was found that separation factor (α) of PVA/PSF composite membrane with single finger‐void membrane structure was higher than that with the sponge‐like membrane structure. Therefore, single finger‐void membrane structure as the supported membrane was more suitable than sponge‐like membrane structure for the preparation of PVA/PSF hollow fiber composite membrane. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 247–254, 2005     

Crosslinked blended poly(vinyl alcohol)/N-methylol nylon-6 membranes for the pervaporation separation of ethanol–water mixtures

Crosslinked blended membranes of poly(vinyl alcohol) (PVA) and N-methylol nylon-6 were prepared either by thermal crosslinking at 180°C or by chemical crosslinking with maleic acid. The pervaporation performance for the separation of ethanol–water mixtures of these membranes was investigated in terms of feed concentration, PVA content, and crosslinking agent content. The pervaporation performance of two differently crosslinked membranes was strongly influenced by the nature of the crosslinkage. Significant improvement in the pervaporation separation index can be achieved for chemically crosslinked membranes. From the comparison between the pervaporation and sorption tests, it is suggested that, for hydrophilic membranes, sorption properties dominate the pervaporation performance at feed solutions of higher water content, while diffusion properties govern at feed solutions of higher ethanol content. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 317–327, 1998     

Synthesis and characterization of hybrid membranes using poly(vinyl alcohol) and tetraethylorthosilicate for the pervaporation separation of water–isopropanol mixtures

Hybrid membranes were prepared using poly(vinyl alcohol) (PVA) and tetraethylorthosilicate (TEOS) via hydrolysis and cocondensation reaction for the pervaporation separation of water‐isopropanol mixtures. The resulting membranes were characterized by Fourier transform infrared spectroscopy, wide‐angle X‐ray diffraction, and differential scanning calorimetry. The glass transition temperature of these membranes varied from 100 to 120°C with increasing TEOS content. Effects of crosslinking density and feed compositions on the pervaporation performances of the membranes were studied. The membrane containing 1.5:1 mass ratio of TEOS to PVA gave the highest separation selectivity of 900 at 30°C for 10 mass % of water in the feed mixture. It was found that the separation selectivity and permeation flux data are strongly dependent on the water composition of the feed and operating temperature. However, the membrane with the highest crosslinking density showed unusual pervaporation properties. The overall activation energy values were calculated using the Arrhenius‐type equation. The activation energy values for the permeation and diffusion varied from 49.18 to 64.96 and 55.13 to 67.31 kJ/mol, respectively. Pervaporation data have also been explained on the basis of thermodynamic quantities. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1304–1315, 2004     

PVA基聚电解质渗透汽化膜的研究进展

介绍了聚电解质及其渗透汽化膜材料的优异性能,综述了聚乙烯醇(PVA)聚电解质渗透汽化膜材料的研究进展,阐述了两性聚电解质(APE)材料的特性,其内盐结构改善了膜的耐水性和耐高温性.90℃时,各种PVA基APE材料用于纯度为95%的工业乙醇脱水,分离因子在1 100～1 300,渗透通量为2 500～1 600g/(m<...     

Selective separation of water from aqueous alcohol mixtures through functionalized syndiotactic poly(styrene‐co‐4‐methylstyrene) membranes by pervaporation

The pervaporation performances of a series of functionalized syndiotactic poly(styrene‐co‐4‐methylstyrene) (SPSM) membranes for various alcohol mixtures were investigated. The syndiotactic polystyrene copolymers, poly(styrene‐co‐4‐methylstyrene) (SPSM), were prepared by styrene with 4‐methylstyrene using a Cp*Ti(OCH₃)₃/methyl aluminoxane (metallocene/MAO) catalyst. The effect of functionalization on the thermal properties and polymer structure of the SPSM membranes were also investigated. The crystallinity of the functionalized SPSM membrane is lower than that of the unfunctionalized SPSM membranes. The water molecules preferentially permeate through the SPSM membranes. Compared with unfunctionalized SPSM membranes, the functionalized SPSM membrane effectively increases the membrane formation performances and the pervaporation performances. The optimun pervaporation performance (a separation factor of 510 and permeation rate of 220 g/m²h) was obtained by the bromination of SPSM (SPSMBr) membrane with a 90 wt % aqueous ethanol solution. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2247–2254, 2002     

Poly(vinyl alcohol) and poly(vinyl amine) blend membranes for isopropanol dehydration

Blended membranes of hydrophilic polymers poly(vinyl alcohol) (PVA) and poly(vinyl amine) (PVAm) were prepared and crosslinked with glutaraldehyde. The prepared membranes were characterized using infrared (attenuated total reflection mode) spectroscopy, differential scanning calorimetry, X‐ray diffractometry, and scanning electron microscopy measurements. Pervaporation performances of the membranes were evaluated for the separation of water‐isopropanol (IPA) mixtures. As the PVAm content increased from PVAm0 to PVAm1.5, the flux through a 70 μm film increased from 0.023 to 0.10 kg/m² h at an IPA/water feed ratio of 85/15 at 30 °C. The driving force for permeation of water increased due to the temperature but it has no effect on IPA permeation. Activation energies for the permeation of IPA and water were calculated to be 17.11 and 12.46 kJ/mol, respectively. Controlling the thickness of the blend membrane could improve the permeation flux with only a marginal reduction in the separation factor. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45572.     

Syntheses and characterization of blend membranes of sodium alginate and poly(vinyl alcohol) for the pervaporation separation of water + isopropanol mixtures

The blend membranes of sodium alginate and poly(vinyl alcohol) have been prepared by physical mixing in different ratios (75, 50, and 25%) of sodium alginate with poly(vinyl alcohol). The membranes were crosslinked with glutaraldehyde and used in the pervaporation separation of water + isopropanol mixtures at 30°C. The crosslinking reaction was confirmed by Fourier transform infrared spectra. Permeation flux increased with an increase in mass % of water in the feed mixture as well as with an increase in the amount of poly(vinyl alcohol) in the blend, but separation selectivity decreased. Diffusion coefficients of water + isopropanol mixtures have been calculated using the Fick's equation from the sorption data. Arrhenius activation parameters were calculated for 10 mass % of water in the feed mixture using the values of flux and diffusion coefficients obtained at 30, 40, and 50°C. The diffusion and pervaporation results have been explained on the basis of solution‐diffusion principles. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3642–3651, 2002     

Blend membranes of chitosan and poly(vinyl alcohol) in pervaporation dehydration of isopropanol and tetrahydrofuran

Blend membranes of a natural polymer, chitosan, with a synthetic polymer, poly(vinyl alcohol) (PVA), were prepared by solution casting and crosslinked with a urea formaldehyde/sulfuric acid (UFS) mixture. Chitosan was used as the base component in the blend system, whereas PVA concentration was varied from 20 to 60 wt %. Blend compatibility was studied by differential scanning calorimetry, and Fourier transform infrared spectroscopy was used to study membrane crosslinking. Membranes were tested for pervaporation dehydration of isopropanol and tetrahydrofuran (THF) at 30°C in close proximity to their azeotropic compositions. Membrane performance was assessed by calculating flux and selectivity. Swelling experiments performed in water + organic mixtures at 30°C were used to explain the pervaporation results. The blend membrane containing 20 wt % PVA when tested for 5 and 10 wt % water–containing THF and isopropanol feeds exhibited selectivity of 4203 and 17,991, respectively. Flux increased with increasing concentration of water in the feed. Selectivity was highest for the 20 wt % PVA‐containing blend membrane. The results of this study are unique in the sense that the crosslinking agent used—the UFS mixture—was novel. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1918–1926, 2007     

Selective separation of some heavy metals by poly(vinyl alcohol)‐grafted membranes

A poly(vinyl alcohol) membrane (PVA) was modified by radiation graft copolymerization of acrylic acid/styrene (AAc/Sty) comonomers. The Cu and Fe ion‐transport properties of these membranes were investigated using a diaphragm dialysis cell. In the feed solution containing CuCl₂ or a mixture of CuCl₂ and FeCl₃, the PVA‐g‐P(AAc/Sty) membranes showed high degrees of permselectivity toward Cu²⁺ rather than toward Fe³⁺. The permeation of Cu²⁺ ions through the membranes was found to increase with decrease in the grafting yield. However, as the content of Cu²⁺ ions in the Cu/Fe binary mixture feed solutions decreased, the rate and the amount of transported Cu²⁺ through the grafted membrane decreased, with no appreciable permselectivity toward Fe³⁺. When Fe²⁺ ions were used instead of Fe³⁺ ions in the feed solution containing Cu²⁺, the transport of both Cu²⁺ and Fe²⁺ through the membrane was observed. The rate of transport of Fe²⁺ was higher than that of Cu²⁺. In addition, it was found that the selective transport of ions was significantly influenced by the pH difference between both sides of the membranes. As the pH of the feed or the received solution decreased, both Cu²⁺ and Fe³⁺ passed through the membrane and were transported to the received solution. The role of carboxylic acid and the hydroxyl groups of the grafted membranes in the transportation process of ions is discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 125–132, 2000     

Characterization of sodium alginate and poly(vinyl alcohol) blend membranes in pervaporation separation

By blending a rigid polymer, sodium alginate (SA), and a flexible polymer, poly(vinyl alcohol) (PVA), SA/PVA blend membranes were prepared for the pervaporation separation of ethanol–water mixtures. The rigid SA membrane showed a serious decline in flux and a increase in separation factor due to the relaxation of polymeric chains, whereas the flexible PVA membrane kept consistent membrane performance during pervaporation. Compared with the nascent SA membrane, all of the blend membranes prepared could have an enhanced membrane mobility by which the relaxation during pervaporation operation could be reduced. From the pervaporation separation of the ethanol–water mixtures along with the temperature range of 50–80°C, the effects of operating temperature and PVA content in membrane were investigated on membrane performance, as well as the extent of the relaxation. The morphology of the blend membrane was observed with PVA content by a scanning electron microscopy. The relaxational phenomena during pervaporation were also elucidated through an analysis on experimental data of membrane performance measured by repeating the operation in the given temperature range. SA/PVA blend membrane with 10 wt % of PVA content was crosslinked with glutaraldehyde to enhance membrane stability in water, and the result of pervaporation separation of an ethanol–water mixture through the membrane was discussed. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:949–959, 1998     

Pervaporation separation of water‐isopropyl alcohol mixtures with blend membranes of sodium alginate and poly(acrylamide)‐grafted guar gum

The blend membranes of sodium alginate (Na‐Alg) and poly(acrylamide)‐grafted guar gum (PAAm‐g‐GG) in the ratios of 3:1 and 1:1 were prepared and studied for the pervaporation separation of water–isopropyl alcohol mixtures over the entire range of mixture composition at 30°C. Membranes prepared from neat Na‐Alg (M‐1) and the 1:1 blend of Na‐Alg and PAAm‐g‐GG (M‐3) showed the highest separation selectivity for 10 mass % water in the feed mixture, whereas membranes prepared with the 3:1 blend ratio of Na‐Alg to PAAm‐g‐GG showed the highest separation selectivity of 20 mass % water in the feed. Selectivity decreased with increasing amount of water in the feed for all the membranes, but these values show an increase with increasing amount of grafted copolymer in the blend mixture. Flux increased with increasing amount of water in the mixture, but the flux values did not change markedly with the PAAm‐g‐GG content in the blend membrane at the lower mass % water. At higher mass % of water, the flux values of the blends increase systematically with increasing amount of PAAm‐g‐GG in the blend polymer. For the 10 mass %‐containing binary mixtures, the pervaporation separation experiments were performed at 30, 40, and 50°C, and the resulting data were used to calculate the Arrhenius activation parameters. These data indicated activated pore‐type diffusion of the permeants in the membranes. Dynamic sorption studies were also performed on up to 40 mass % water–isopropyl alcohol mixtures at 30°C. These results, when analyzed by the empirical equation, indicated Fickian transport in all the cases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2014–2024, 2002