Modification of jute by acrylic acid in the presence of Na3PO4 and K2S2O8 as catalysts under thermal treatment

Jute fabric was modified using acrylic acid (AA) as the finishing agent in the presence of K₂S₂O₈ and Na₃PO₄ catalysts separately or in selected combinations, employing a pad–dry–cure technique. Treatment with 10% acrylic acid at 30°C and at pH 7 produced optimum effects: a batching time of 45–60 min at 30°C, followed by drying of the batched fabric at 95°C for 5 min and curing of the dried fabric at 140°C for 5 min produced most balanced improvements in the textile related properties. Na₃PO₄ catalyst allowed esterification of AA with cellulosic, hemicellulosic, and lignin constituents of jute, and K₂S₂O₈ catalyst allowed radical polymerization of free acrylic acid or jute-bound acrylic acid moieties; the said processes ultimately lead to some degree of crosslinking of the chain polymers of jute. Examination of the surface morphology of untreated and treated jute fabrics by scanning electron microscopy revealed a good degree of masking effect on the unit cells of jute and intercellular regions by a cohesive film of polyacrylic acid or its salts, particularly when K₂S₂O₈ was used either alone or in combination with Na₃PO₄ as catalyst. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68:63–74, 1998     

Effect of epoxidized soybean oil on mechanical properties of woven jute fabric reinforced aromatic and aliphatic epoxy resin composites

A systematic study was performed to describe the effect of epoxidized soybean oil (ESO) on storage modulus, glass transition temperature (T _g) and mechanical properties in epoxy resin composites reinforced by jute fabric. In addition to aromatic diglycidylether of bisphenol‐A (DGEBA) resin, a glycerol (GER)‐and a pentaerythritol (PER)‐based aliphatic resin was applied as base resin, which can be also synthesized from renewable feedstock. Based on strip tensile test results, the usual alkali treatment of jute fabric was avoided. By increasing the ESO‐content in aliphatic composites the T _g increases, whereas in case of DGEBA, it decreases. The results indicate that although ESO has a significant softening effect, the jute fiber‐reinforced DGEBA composite can be replaced without significant compromise in mechanical properties by a potentially fully bio‐based composite consisting of 25 mass% ESO‐containing aliphatic PER‐reinforced by jute fibers. POLYM. COMPOS., 38:884–892, 2017. © 2015 Society of Plastics Engineers     

Jute fabric reinforced engineering thermoplastic sandwich composites. I. The effect of molding time

Jute fabric‐reinforced sandwich composites were fabricated using engineering thermoplastics. The jute fabrics were precoated with thermosetting resin to improve their thermal resistance before molding of the composites. Thermal gravimetric analysis (TGA) studies revealed that the resin coated fabrics decomposed at higher temperature than the uncoated jute. The onset of degradation of the coated fibers also falls between that of jute fibers and the thermoset resins. This indicates the presence of good interfacial bonding between jute fibers and both resins. Isothermal TGA studies revealed that jute could withstand brief exposure to higher temperature at 270 and 290°C. The sandwich composites were fabricated at 270°C by compression molding for 1.5 and 3 min in each case, and then characterized by flexural, tensile and morphological studies, i.e., SEM and optical microscopy. The uncoated jute fabric yielded composites of superior mechanical properties even with 3 mins molding at 270°C which is close to the degradation temperature of uncoated jute fibers. This is an indication that it is feasible to prepare jute fiber filled engineering polymer composites provided the exposure time at high temperature during processing does not exceed 3 mins as determined by TGA isothermal studies. SEM studies revealed strong fiber/matrix interfacial bonding between jute and the thermoset resins while the inferior mechanical properties of the resin coated sandwich composites could be attributed to the poor interfacial bonding between the already cured thermoset coating and the matrix based on optical microscopy of the polished cross‐sections. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Modification of jute fabric via laccase/t‐BHP‐mediated graft polymerization with acrylamide

Enzymatic processes provide new perspectives for the modification of lignocellulose materials. Lignin is an excellent substrate for laccase, and the modification of lignin‐rich jute fabric via graft polymerization with acrylamide (AAm) mediated by laccase and tert‐butyl hydroperoxide (t‐BHP) was investigated in this study. The products obtained were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. The grafting rate was determined in terms of elemental analysis. The hydrophilicity and thermal and dyeing properties of the modified jute fabric were studied. The results supported the conclusion that the polyacrylamide was grafted on the lignin of the jute fiber by laccase in coordination with t‐BHP, representing a grafting rate of 2.87%. The hydrophilicity, thermostability, dye uptake, and dyeing depth of the jute fiber were increased after the enzymatic graft modification with AAm. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40387.     

Effect of graft copolymerization of mixtures of acrylamide and methyl methacrylate on mechanical properties of jute fibers of different compositions

The role of persulfate-induced graft copolymerization of mixtures of acrylamide and methyl methacrylate at 50°C in modifying mechanical properties of jute fibers of different compositions was studied in a limited aqueous system following a pretreatment technique. Results obtained indicate that such a process admits a good scope for modification of mechanical properties of jute fiber depending on degree of grafting achieved and compositional variations of (1) the feed monomer mixture and (2) the multiconstituent jute itself, consequent to selective removal of lignin and hemicellulose to different extents from the fiber. Low to moderate removal of hemicellulose is more effective than a similar degree of removal of lignin from jute in rendering the fiber more amenable to vinyl grafting using the mixed monomer system without being adversely affected with respect to tensile properties. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1139–1147, 1998     

Thermal behavior of vinyl ester resin matrix composites reinforced with alkali‐treated jute fibers

The thermal behavior of vinyl ester resin matrix composites reinforced with jute fibers treated for 2, 4, 6, and 8 h with 5% NaOH was studied with Thermo‐gravimetric analysis and differential scanning calorimetry. The moisture desorption peak shifted to a higher temperature, from 37 to 58.3°C, for all the treated‐fiber composites because of improved wetting of the fibers by the resin and stronger bonding at the interface. The degradation temperature of the vinyl ester resin in the composites was lowered to 410.3°C from that of the neat resin, 418.8°C. The X‐ray diffraction studies showed increased crystallinity of the treated fibers, which affected the enthalpy of the α‐cellulose and hemicellulose degradation. The hemicellulose degradation temperature remained the same (299.7°C) in all the treated‐fiber composites, but the enthalpy associated with the hemicellulose degradation showed an increasing trend in the treated composites with a small increase in the weight loss. This could be attributed to the increased hydrogen bonding between the more accessible ? OH groups of the hemicellulose in the noncrystalline region of the jute fiber and the resin. The degradation temperature of α‐cellulose was lowered from 364.2 to 356.8°C in the treated composites. The enthalpy of α‐cellulose degradation showed a decreasing trend with a lowering of the weight loss. The crystalline regions of the fiber, consisting of closely packed α‐cellulose chains, were bonded with the resin mainly on the surface through hydrogen bonds and became more resistant to thermal degradation; this reduced the weight loss. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 123–129, 2004     

Infrared spectra of jute stick bleached with sodium chlorite and hydrogen peroxide

Jute stick was bleached with sodium chlorite and alkaline hydrogen peroxide solutions. The infrared (IR) spectra of bleached samples and jute stick were analyzed and compared. The bleached samples were characterized by higher absorbance intensity ratios (A_v/A₂₉₀₀) of the bands attributed to hemicellulose. Among the bleached samples the chlorite-bleached sample showed higher intensity for the bands mentioned. The bands attributed to lignin are either absent or very weak in the chlorite-bleached jute stick as compared to that of peroxide-bleached jute stick, although some residual lignin was present in the substrate. The 1635 cm^?1 band attribute to the vibration of adsorbed water molecules in the noncrystalline regions in cellulose appears as a sharp peak in chlorite-bleached jute stick and as a shoulder in peroxide-bleached jute stick. This can be attributed to the difference in the nature of the two bleaching processes.     

Thermomechanical properties of alkali treated jute‐polyester/nanoclay biocomposites fabricated by VARTM process

A systematic study was carried out to investigate the effect of alkali treatment and nanoclay on thermomechanical properties of jute fabric reinforced polyester composites (JPC) fabricated by the vacuum‐assisted resin transfer molding (VARTM) process. Using mechanical mixing and sonication process, 1% and 2% by weight montmorillonite K10 nanoclay were dispersed into B‐440 premium polyester resin to fabricate jute fabric reinforced polyester nanocomposites. The average fiber volume was determined to be around 40% and void fraction was reduced due to the surface treatment as well as nanoclay infusion in these biocomposites. Dynamic mechanical analysis (DMA) revealed enhancement of dynamic elastic/plastic responses and glass transition temperature (T_g) in treated jute polyester composites (TJPC) and nanoclay infused TJPC compared with those of untreated jute polyester composites (UTJPC). Alkali treatment and nanoclay infusion also resulted in enhancement of mechanical properties of JPC. The maximum flexural, compression, and interlaminar shear strength (ILSS) properties were found in the 1 wt % nanoclay infused TJPC. Fourier transform‐infrared spectroscopy (FT‐IR) revealed strong interaction between the organoclay and polyester that resulted in enhanced thermomechanical properties in the composites. Lower water absorption was also observed due to surface treatment and nanoclay infusion in the TJPC. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and properties of successive alkali treated completely biodegradable short jute fiber reinforced PLA composites

The natural fiber reinforced biodegradable polymer composites were prepared with short jute fiber as reinforcement in PLA (Poly lactic acid) matrix. The short jute fiber is successively treated with NaOH at various concentrations (5%, 10%, and 15%) and H₂O₂. The composites were prepared with untreated and treated short jute fibers at different weight proportions (up to 25%) in PLA and investigated for mechanical properties. The results showed that the composite with successive alkali treated jute fiber at 10% NaOH and H₂O₂ with 20% fiber loading has shown 18% higher flexural strength than neat PLA and untreated jute/PLA composite. The flexural modulus of the composite at 25% fiber loading was 125% and 110% higher than that of composites with untreated fibers and neat PLA, respectively. The impact strength of composite with untreated fibers at higher fiber weight fraction was 23% high as compared to neat PLA and 26% high compared to composite with treated fibers. The water absorption was more for untreated jute/PLA composite at 25% fiber loading than all other composites. The composite with untreated fibers has high thermal degradation compared with treated fibers but lower than that of pure PLA matrix. The enzymatic environment has increased the rate of degradation of composites as compared to soil burial. Surface morphology of biodegraded surfaces of the composites were studied using SEM method. POLYM. COMPOS., 37:2160–2170, 2016. © 2015 Society of Plastics Engineers     

Study on depositing SiO2 nanoparticles on the surface of jute fiber via hydrothermal method and its reinforced polypropylene composites

To improve the interfacial compatibility of jute fiber reinforced polypropylene (PP) composites, hydrothermal method was used to deposit SiO₂ nanoparticles on the surface of pretreated jute fibers and the effect of reaction factors (tetraethoxysilane [TEOS] concentration, ammonia concentration, and reaction temperature) on the deposition of SiO₂ nanoparticles were evaluated. The results of FTIR, XRD, SEM, and TEM showed that the amorphous SiO₂ nanoparticles with an average particle size of 65.0 nm were successfully deposited on the surface of jute fibers at the TEOS/H₂O volume ratio of 1:2, ammonia of 0.55 M, reaction temperature of 100 °C (0.15 MPa) for 5 h. Compared with the sol–gel method, SiO₂ nanoparticles obtained by the hydrothermal method possessed smaller particle size and were less agglomerated, which can better fill in the surface defects of the jute fibers and result in a 12.9% increase in the tensile strength. The study on the mechanical properties and interface performance of the jute fiber reinforced PP composites indicated that the interfacial compatibility between jute fibers and PP was obviously improved. The tensile and impact strength of the composites reinforced with nano‐SiO₂ deposited jute fibers were increased by 26.87% and 25.65%, respectively, compared with the untreated jute fibers. J. VINYL ADDIT. TECHNOL., 26:43–54, 2020. © 2019 Society of Plastics Engineers     

Jute felt composite from lignin modified phenolic resin

Raw and dewaxed jute felt composites were prepared with resol and lignin modified phenol formaldehyde resin. Four different types of lignin modified resins were used by replacing phenol with lignin. The lignin modified resins were prepared from purified lignin obtained from paper industry waste black liquor. To investigate bonding between jute and resin, IR spectroscopy of jute felts and composites was carried out. The thermal stability of the composites was assessed by DSC and TGA. It was found that the lignin resin jute composite is thermally more stable than resol composite. XRD of jute felt and composite shows that the crystallinity of the jute fiber increases after composite preparation. The lignin resin composites were tested for water absorption and thickness swelling, and it was found that the results are comparable with those of resol jute composite. Composites prepared from lignin phenol formaldehyde resin with 50% phenol replacement has shown 75% tensile strength retention to that of pure resol jute composite.     

Effect of lactic acid chain length on thermomechanical properties of star‐LA‐xylitol resins and jute reinforced biocomposites

Star‐shaped bio‐based resins were synthesized by direct condensation of lactic acid (LA) with xylitol followed by end‐functionalizing of branches by methacrylic anhydride with three different LA chain lengths (3, 5 and 7). The thermomechanical and structural properties of the resins were characterized by ¹³C NMR, Fourier transform IR spectroscopy, rheometry, DSC, dynamic mechanical analysis (DMA), TGA and flexural and tensile tests. An evaluation of the effect of chain length on the synthesized resins showed that the resin with five LAs exhibited the most favorable thermomechanical properties. Also, the resin's glass transition temperature (103 °C) was substantially higher than that of the thermoplast PLA (ca 55 °C). The resin had low viscosity at its processing temperature (80 °C). The compatibility of the resin with natural fibers was investigated for biocomposite manufacturing. Finally, composites were produced from the n5‐resin (80 wt% fiber content) using jute fiber. The thermomechanical and morphological properties of the biocomposites were compared with jute‐PLA composites and a hybrid composite made of the impregnated jute fibers with n5 resin and PLA. SEM and DMA showed that the n5‐jute composites had better mechanical properties than the other composites produced. Inexpensive monomers, good thermomechanical properties and good processability of the n5 resin make the resin comparable with commercial unsaturated polyester resins. © 2017 Society of Chemical Industry     

A Comparative Study on the Mechanical,Degradation and Interfacial Properties of Jute/LLDPE and Jute/Natural Rubber Composites

Jute fabric (hessian cloth) reinforced low-density polyethylene (LLDPE) composites (40 wt%) and solid natural rubber-(NR) based composites (40 wt%) were fabricated by compression molding. Tensile strength (TS), tensile modulus (TM) and percentage elongation at break (Eb) of jute/LLDPE composites were found to be 29, 680 MPa and 20%, and for jute/NR-based composites were also found to be 15, 122 MPa and 94%, respectively. Interfacial shear strength (IFSS) of the jute/LLDPE and jute/NR systems was investigated by using the single fiber fragmentation test (SFFT). Scanning electron microscopy (SEM) and aqueous degradation tests were also performed.     

Characterization of the draping behavior of jute woven fabrics for applications of natural‐fiber/epoxy composites

In this study, we investigated the draping behavior of jute woven fabric to study the feasibility of using natural fabrics in place of synthetic glass‐fiber fabrics. Draping behavior describes the in‐mold deformation of fabrics, which is vital for the end appearance and performance of polymer composites. The draping coefficient was determined with a common drapemeter for fabrics with densities of 228–765 g/m² and thread counts under different humidity and static dynamic conditions. The results were compared to glass‐fiber fabrics with close areal densities. Characterization of the jute fabrics was carried out to fill the knowledge gap about natural‐fiber fabrics and to ease their modeling. The tensile and bending stiffnesses and the shear coupling were also characterized for a plain woven jute fabric with a tensile machine, Shirley bending tester, and picture frame, respectively. As a case study, the draping and resin‐transfer molding of the jute fabric over a complex asymmetric form was performed to measure the geometrical conformance. The adoption of natural fibers as a substitute for synthetic fibers, where the strength requirements are satisfied, would thus require no special considerations for tool design or common practices. However, the use of natural fibers would lead to weight and cost reductions. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1453–1465, 2013     

Graft copolymerization of styrene,methylmethacrylate, and acrylonitrile onto jute fibres

The contribution of jute constituents, namely, water soluble matters, waxes, pectins, lignin, hemicelluloses, and α-cellulose in the graft copolymerization reaction of jute fabric with some vinyl monomers was investigated. Styrene, methylmethacrylate, and acrylonitrile were used as the monomers and Fe²⁺/H₂O₂ redox system as initiator. The graft copolymerization reaction was carried out at 80°C using different concentrations of monomer and initiator for different lengths of time. The water soluble matters, pectins, and lignin were found to accelerate the graft copolymerization reaction during the initial stages of the reaction and in the meantime impede termination during the latter stages of the reaction. Generally, the magnitude of grafting is governed by nature of the substrate, nature of the monomer, and the conditions of the polymerization reaction. Grafting decreases the moisture regain of jute and substrates derived thereof irrespective of the monomer used within the range studied. Also, grafting decreases the tensile strength and imparts rot-proofing properties to the substrates examined.     

Study of jute fiber reinforced polyester composites by dynamic mechanical analysis

Cyanoethylation of jute fibers in the form of nonwoven fabric was studied, and these chemically modified fibers were used to make jute–polyester composites. The dynamic mechanical thermal properties of unsaturated polyester resin (cured) and composites of unmodified and chemically modified jute–polyester were studied by using a dynamic mechanical analyzer over a wide temperature range. The data suggest that the storage modulus and thermal transition temperature of the composites increased enormously due to cyanoethylation of fiber. An increase of the storage modulus of composites, prepared from chemically modified fiber, indicates its higher stiffness as compared to a composite prepared from unmodified fiber. It is also observed that incorporation of jute fiber (both unmodified and modified) with the unsaturated resin reduced the tan δ peak height remarkably. Composites prepared from cyanoethylated jute show better creep resistance at comparatively lower temperatures. On the contrary, a reversed phenomenon is observed at higher temperatures (120°C and above). Scanning electron micrographs of tensile fracture surfaces of unmodified and modified jute–polyester composites clearly demonstrate better fiber–matrix bonding in the case of the latter. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1505–1513, 1999     

Graft copolymerization of nitrile monomers onto bleached jute fiber using potassium persulfate system and their textile characteristics

Graft copolymerization of nitrile monomers, such as acrylonitrile and methacrylonitrile, onto bleached jute fiber was carried out by using K₂S₂O₈/FeSO₄ redox system in nitrogen atmosphere and their effect on the textile characteristics was also investigated. Percent graft yield increased with the increase of concentrations of monomer, initiator, and catalyst, reaction time, and reaction temperature up to a certain value, and, thereafter, it decreased. The effect of percent grafting efficiency was similar to that of percent graft yield, except for the monomer concentration. The increase of percent graft yield was dependent on the availability of jute‐macroradicals as well as monomer radicals. Sometimes the predominancy of homopolymerization over grafting and the premature termination of growing grafted chains occurred because of the higher monomer radicals and excess primary radicals, SO₄^?? and ^?OH, from K₂S₂O₈ initiator. The percent graft yield of acrylonitrile and methacrylonitrile was 20.5 and 29.1%, respectively. Higher graft yield for methacrylonitrile might be due to the methyl group present in it. Infrared spectra at 2229–2235 cm^?1 of acrylonitrile‐ and methacrylonitrile‐grafted jute strongly supported the graft formation. Grafting of jute fiber improved the thermal stability, protected from photooxidative degradation, and decreased swellability as well as dyeability, etc. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3622–3629, 2004     

Delignification of intact biomass and cellulosic coproduct of acid‐catalyzed hydrolysis

The kinetics of acid‐catalyzed hemicellulose removal and also alkaline delignification of oat hull biomass were investigated. All three operational parameters namely, catalyst concentration (0.10–0.55 N H₂SO₄), temperature (110–130°C), and residence time (up to 150 min) affected the efficiency of hemicellulose removal, with 100% of hemicellulose removed by appropriate selection of process parameters. Analysis of delignification kinetics (in the temperature range of 30–100°C) indicated that it can be expressed very well by a two‐phase model for the crude biomass and also for the hemicellulose‐prehydrolyzed material. The application of acid‐catalyzed prehydrolysis improved the capacity of lignin dissolution especially at lower temperatures (30 and 65°C) and accelerated the dissolution of lignin. This acceleration of delignification by prehydrolysis was possible at all levels of temperature in the bulk phase; however, results were more significant at the lower temperatures in the terminal phase. © 2015 American Institute of Chemical Engineers AIChE J, 61: 1783–1791, 2015     

Lignin in jute fabric–polypropylene composites

In this work, the feasibility of using lignin as a compatibilizer for composites made from jute fiber fabric and polypropylene (PP) was studied. Since lignin contains polar (hydroxyl) groups and nonpolar hydrocarbon, it was expected to be able to improve the compatibility between the two components of the composite. It was found that lignin acted as β nucleation, fire retardant, and toughening agent for PP matrix. Jute composites exhibit higher stiffness, tensile strength, and impact behavior in respect to those of neat PP. Although scanning electron micrographic observations indicate that PP‐jute adhesion was slightly improved by lignin addition, additional benefits were only obtained from impact behavior. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical properties of phenolic composites reinforced with jute/cotton hybrid fabrics

Mechanical properties (tensile, flexural, impact, and dynamic mechanical thermal analysis) of novolac type phenolic composites reinforced with jute/cotton hybrid woven fabrics were investigated as a function of fiber orientation and roving/fabric characteristics. Scanning electron microscopy (SEM) was carried out to investigate the fiber‐matrix adhesion. Results showed that the composite properties are strongly influenced by test direction and rovings/fabric characteristics. The anisotropy degree was shown to increase with test angle and to strongly depend on the type/architecture of fabric used, i.e., jute rovings diameter, relative fiber content, etc. It was possible to obtain composites with higher mechanical properties and lower anisotropy degree by producing cross‐ply laminates. Best overall mechanical properties were obtained for the composites tested along the jute rovings direction. Composites tested at 45° and 90° with respect to the jute roving direction exhibited a controlled brittle failure combined with a successive fiber pullout, while those tested in the longitudinal direction (0°) exhibited a catastrophic failure mode. Our results indicate that jute promotes a higher reinforcing effect and cotton avoids catastrophic failure. Therefore, this combination of natural fibers is suitable to product composites for lightweight structural applications. POLYM. COMPOS., 26:1–11, 2005. © 2004 Society of Plastics Engineers.