Use of wood fibers in thermoplastics. VII. The effect of coupling agents in polyethylene–wood fiber composites

Linear low density polyethylene (LLDPE) was reinforced with different wood fibers, aspen chemithermomechanical pulp (bleached and unbleached), and other commerical wood pulps. Silane coupling agents A-172, A-174, A-1100, and polymethylene polyphenyl isocyanate were used to improve the bonding between the fiber and matrix. LLDPE filled with pretreated wood fiber produced a significant improvement in tensile strength and modulus. Comparison of tensile and impact properties of wood fiber composites with mica and glass fiber composites shows the potential advantage (in terms of material cost and specific properties) of wood fiber as a reinforcement.     

Thermal and mechanical characterization of linear low‐density polyethylene/wood flour composites

A linear low‐density polyethylene (LLDPE) matrix was modified with an organic peroxide and by a reaction with maleic anhydride (MAn) and was simultaneously compounded with untreated wood flour in a twin‐screw extruder. The thermal and mechanical properties of the modified LLDPE and the resulting composites were evaluated. The degree of crystallinity was reduced in the modified LLDPE, but it increased with the addition of wood flour for the formation of the composites. Significant improvements in the tensile strength, ductility, and creep resistance were obtained for the MAn‐modified composites. This enhancement in the mechanical behavior could be attributed to an improvement in the compatibility between the filler and the matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2775–2784, 2003     

杨木纤维表面改性及其HDPE复合材料性能研究

利用过氧化物作为引发剂,加入马来酸酐偶联把聚乙烯蜡接枝到杨木纤维表面上。接枝前后木纤维的红外光谱和色散自由能的显著变化证实了接枝反应的发生,并通过一系列实验计算了反应的接枝率;随着反应温度的提高,接枝率呈上升趋势,在170％以上变化趋势变缓。与未改性的木纤维相比,改性后木纤维填充HDPE复合材料的力学性能有较大提高,其拉伸、弯曲、冲击强度可分别提高34．9％,29．2％和8．8％,但随着聚乙烯蜡接枝量的增大,材料力学性能又有所下降。扫描电镜照片显示改性木纤维在基体中分散更均匀,界面结合良好。     

Use of grafted aspen fibers in thermoplastic composites: IV. Effect of extreme conditions on mechanical properties of polyethylene composites

Hardwood fibers of aspen in the form of chemithermo-mechanical pulp (CTMP) have been used as reinforcement in linear low density polyethylene (LLDPE). The effect of composite treatment (immersion in boiling water, heat exposure at 105°C for seven days or at a temperature of −40°C) on resulting mechanical properties were evaluated. The grafted aspen CTMP composites showed by far the best results with regard to secant modulus, tensile strength, energy, and strain when compared to those of wood flour, mica or glass–fiber filled LLDPE, as well as to virgin LLDPE. Finally, the dimensional stability of CTMP aspen-filled LLDPE composites immersed for four hours in boiling water was better than that of mica or glass–fiber filled LLDPE.     

Some studies on mechanical properties of wood flour/continuous glass mat/polypropylene composite

The mechanical properties and the surface property of wood flour/continuous glass mat/polypropylene composites have been investigated. The suitability of wood flour as a filler for continuous glass mat–reinforced polypropylene has been tested using different mesh sizes (e.g., 20 and 40 mesh), as well as by varying the weight percentage of wood flour from 0%– 30%. Moreover, different treatments such as coupling agent A‐1100 and functionalized polypropylene grafting with maleic anhydride, and so forth, have also been used to improve the compatibility of wood flour and glass fiber with the polymer resin. In addition, the effects of the surface weight of glass mat and matrix resin have been studied. The extent of the improvement in mechanical properties depends on the wood flour content and size, the surface weight of the glass mat, the matrix resin, and the surface treatment of wood flour. After adding wood flour, the contact angle of distilled water on the composite surface decreases and the polar component of surface tension increases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 536–544, 2002     

改性处理对木纤维/聚乳酸生物可降解复合材料性能的影响

分别用硬脂酸和钛酸酯对木纤维进行改性,用注塑成型工艺制备木纤维/聚乳酸可生物降解复合材料。研究了改性剂用量对复合材料力学性能及生物降解性能的影响。结果表明:改性剂对木纤维进行处理后,复合材料的拉伸强度与冲击强度得到明显提高;钛酸酯偶联剂的改性效果优于硬脂酸。硬脂酸和钛酸酯改性剂一定程度上都可以改善复合材料的生物降解性能。     

Effects of repetitive processing,wood content,and coupling agent on the mechanical,thermal, and water absorption properties of wood/polypropylene green composites

In an effort to determine to what extent natural fiber/plastic composites were recyclable, this study conducted repetitive processing cycles on wood flour/polypropylene composites through extrusion up to three times followed by injection molding. Mechanical properties of the composites, containing 10–50?wt% wood flour and with/without addition of 3?wt% maleic anhydride polypropylene (MAPP) as coupling agent, were evaluated by conducting tensile test, thermal analysis, and water absorption test. Repetitive processing as well as wood content and coupling agent addition influenced physical properties of the composites. MAPP functioned well in improving fiber-matrix adhesion in terms of mechanical properties. Repetitive processing did not deteriorate the composite’s properties; rather opposite effect was shown. Thermal analysis indicated that the alteration in properties was contributed by the molecular condition of the polypropylene matrix. Water absorption increased with the wood flour content but reduced when MAPP was added and with more processing cycles.     

Influence of maleic anhydride as a coupling agent on the performance of wood fiber-polystyrene composites

The lack of polar groups in thermoplastics (e.g., in polystyrene) provides low adhesion with cellulosic fibers. To improve compatibility between reinforcement and matrix, maleic anhydride (MA) was selected as a coupling agent for wood fiber-filled polystyrene composites. In general, the mechanical properties improved along with increased concentrations of MA, initiator (e.g., benzoyl peroxide) and wood fiber up to a certain limit and then decreased. The concentrations of MA and fiber which produced maximum improvements in the mechanical properties varied according to wood species, pulping techniques and type of polystyrene. Moreover, properties were further enhanced when another coupling agent (e.g., isocyanate) was used in addition to the MA.     

氧化锌晶须表面改性及表征

采用湿法表面化学改性法，用硅烷和钛酸酯偶联剂对氧化锌晶须(ZnOw)进行了表面改性；考察了溶剂、pH值、温度及分散时间对硅烷类偶联剂改性效果的影响，采用活化指数、接触角以及傅立叶变换红外光谱对改性结果作了表征。同时将改性后的ZnOw填充到线性低密度聚乙烯(LLDPE)中，测试了复合材料的机械性能。实验结果表明，硅烷和钛酸酯偶联剂均能用于ZnOw的表面改性，其最佳改性条件不同，获得最佳改性效果的偶联剂用量也不同。经ND-42改性的ZnOw填充到LLDPE中，复合材料的弯曲强度大幅度提高。     

Effect of chemical treatments of wood fibers on the physical strength of polypropylene based composites

Wood plastic composites attract great attention in various applications. Chemical modification of the wood fiber with NaOH and various coupling agents was performed for wood fiber composites. Wood fibers treated with NaOH, APTES, TEVS, and BC coupling agents were compounded with PP matrix for measuring physical properties. All those chemical treatments increased physical properties much compared to the untreated case because of the elimination of impurities by NaOH treatment and because of the introduction of compatible molecular structure onto the wood fiber surfaces. Especially, the TEVS case showed the best tensile strength, and it could be attributed to the chain structure having double bond of the molecules for high compatibility with PP matrix. The SEM morphology also demonstrated increased adhesion between wood fibers and PP matrix with chemical treatments. The adhesion between wood fiber and PP matrix would be a key parameter in achieving high physical properties of the composite materials.     

Comparative study of maleated polypropylene as a coupling agent for recycled low‐density polyethylene/wood flour composites

The effects of the type of coupling agent and virgin polypropylene (PP) content on the mechanical properties and water absorption behavior of recycled low‐density polyethylene/wood flour (WF) composites were investigated. The fractured surfaces of these recycled wood/plastic composites (rWPCs) were examined to gain insight into the distribution and dispersion of WF within the polymer matrix. The results indicate that the use of 100% recycled polymer led to inferior mechanical properties and to a greater degree of moisture absorption and swelling when compared to recycled polymer–virgin PP wood/plastic composites. This could have been related to the poor melt strength and inferior processability of the recycled polymer. The extent of improvement of the mechanical properties depended not only on the virgin PP content in the matrix but also on the presence of maleic anhydride (MA) modified PP as the coupling agent. Higher concentrations of MA group were beneficial; this improvement was attributed to increased chemical bonding (ester linkages) between hydroxyl moieties in WF and anhydride moieties in the coupling agent. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of the Incorporation of PVC on the Mechanical Properties of the Jute-Reinforced LLDPE Composite

Jute fabrics-reinforced linear low density polyethylene (LLDPE) matrix composites (50 wt% fiber) were prepared by compression molding and mechanical properties were studied. Polyvinyl chloride (PVC) matrix was incorporated instead of LLDPE in the jute based composites and their mechanical properties were investigated and compared with the control composites. It was found that with the increase of PVC in the LLDPE based composites, the mechanical properties were found to improve significantly. Degradation tests of the composites for upto 24 weeks were performed in soil medium. Water uptake and Thermo-mechanical properties of the composites were also studied.     

木粉的碱化处理对木塑复合材料性能的影响

采用木粉填充高密度聚乙烯（HDPE）制备复合材料。为增强亲水性的木粉和憎水性的HDPE基质之间的化学亲和力,对木粉碱化处理。研究了相容剂用量和木粉的碱化处理对复合材料力学性能的影响。结果显示,马来酸酐接枝HDPE可明显提高复合材料的力学性能．表现出很好的增容效果：与用未碱化处理的木粉填充的复合材料相比,木粉的碱化处理使复合材料的弯曲强度和弯曲模量分别下降20．4％和36．2％：在不使用相容剂的情况下,木粉的碱化处理也会使复合材料的拉伸强度下降．但在使用适量相容剂后．则可使复合材料的拉伸强度从未处理时的30．3MPa提高到36．5MPa,与纯HDPE相比,拉伸强度提高了44.8％。     

Use of wood fibers in thermoplastic composites

Wood fibers from aspen and spruce have been used for filler and reinforcement of polystyrene. The wood fibers used were in the form of refined wood. In order to improve compatibility of wood fibers with polymeric matrices, fibers have been modified by copolymerization with styrene. The kanthate method of grafting employing the ferrous-hydrogen peroxide catalytic system was used for fiber treatment. The following properties of composites have been measured: elastic-modulus, tensile strength, and energy absorbed at break. In summary, it has been found that the composites from grafted fibers showed superior mechanical properties to those with original fibers. In general, as a filler, the aspen fibers were superior to spruce, and the shorter fibers superior to longer ones. Mechanical properties of composites as compared to polystyrene were improved as follows: elastic modulus +37 percent; tensile strength +35 percent and energy at breakup by 43.5 percent. The best composites properties have been achieved at 40 percent of fiber fraction present.     

Mechanical strengths of molten and solidified LLDPE/LDPE blends and wood/LDPE composites under tensile deformation

The mechanical strengths of neat low‐density polyethylene (LDPE), a blend of LDPE with linear low‐density polyethylene (LLDPE), and a composite of LDPE with wood flour (wood/LDPE) were investigated in molten and solidified states under tensile deformation. The results are discussed in terms of the effects of LLDPE and wood contents, roller speed, and volumetric flow rate. In LLDPE/LDPE blends, incorporating LLDPE from 0 to 30 wt% into LDPE caused a slight increase in drawdown force, a larger fluctuation in drawdown force, and a reduction of maximum roller speed to failure. The mechanical properties of the solidified LLDPE/LDPE corresponded to those of the molten LLDPE/LDPE with regard to the effect of LLDPE content. For wood/LDPE composites, increasing the wood flour content in molten LDPE caused considerable reductions in drawdown time and maximum roller speed to failure. The drawdown force increased with increasing wood flour up to 10 wt% before it decreased at the wood loading of 20 wt%. A number of voids and pores on the extrudate surfaces became obvious for the composites with 20 wt% of wood content. Increasing wood content enhanced the tensile modulus for the solidified LDPE but decreased its tensile strength. Unlike those of LLDPE/LDPE blends, the changes in tensile modulus and strength of solidified wood/LDPE composites with wood content did not correspond to those of the molten composites. In all cases, the drawdown force increased with increasing roller speed. The effect of volumetric flow rate from the extruder on the mechanical strengths of the solidified blends was more pronounced than on those of the molten ones. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Hybrid composite using recycled polycarbonate/waste silk fibers and wood flour

In this work, hybrid composite materials were made from the combination of waste silk fibers (WSFs) and poplar wood flour (PWF) as reinforcement, recycled polycarbonate (RPC) as polymer matrix, and silane as coupling agent. RPC was obtained from waste compact discs. The effects of fiber type and loading on the mechanical and physical properties of the composites were studied. Experimentally, it was found that the weight content of PWF is a key parameter that would substantially influence the mechanical properties of the samples. The obtained results showed that tensile and flexural strengths and moduli of the composites were significantly enhanced with the addition of biofibers in both types (fiber and flour), as compared with neat RPC. However, the increase in WSFs and PWF contents substantially improved the notched Izod impact strength, but reduced the thermal stability. The significant improvements in mechanical properties of the composites with the incorporation of WSF and PWF were further supported by scanning electron microscopy micrographs. Composites containing more fraction of WSF exhibited higher water absorption (WA) compared with PWF‐filled composites. In addition, composite with higher WSF and PWF (30 wt%) loading showed maximum WA during the whole duration of immersion. POLYM. COMPOS., 37:1667–1673, 2016. © 2014 Society of Plastics Engineers     

Recycled milk pouch and virgin LDPE‐LLDPE‐based jute fiber composites

The present investigation deals with the thermo‐mechanical recycling of post consumer milk pouches (LDPE‐LLDPE blend) and its use as jute fiber composite materials for engineering applications. The mechanical, thermal, morphological, and dynamic‐mechanical properties of recycled milk pouch‐based jute fiber composites with different fiber contents were evaluated and compared with those of the virgin LDPE‐LLDPE/jute fiber composites. Effect of artificial weathering on mechanical properties of different formulated composites was determined. The recycled polymer‐based jute fiber composites showed inferior mechanical properties as well as poor thermal stability compared to those observed for virgin polymer/jute fiber composites. However, the jute‐composites made with (50:50) recycled milk pouch‐virgin LDPE‐LLDPE blend as polymer matrix indicated significantly superior properties in comparison to the recycled milk pouch/jute composites. Overall mechanical performances of the recycled and virgin polymeric composites were correlated by scanning electron microscopy (SEM). The dynamic mechanical analysis showed that storage modulus values were lower for recycled LDPE‐LLDPE/jute composites compared to virgin LDPE‐LLDPE/jute composites throughout the entire temperature range, but an increase in the storage modulus was observed for recycled‐virgin LDPE‐LLDPE/jute composites. POLYM. COMPOS. 28:78–88, 2007. © 2007 Society of Plastics Engineers     

Effect of fiber pretreatment condition on the interfacial strength and mechanical properties of wood fiber/PP composites

The effect of fiber surface pretreatment on the interfacial strength and mechanical properties of wood fiber/polypropylene (WF/PP) composites are investigated. The results demonstrate that fiber surface conditions significantly influence the fiber–matrix interfacial bond, which, in turn, determines the mechanical properties of the composites. The WF/PP composite containing fibers pretreated with an acid–silane aqueous solution exhibits the highest tensile properties among the materials studied. This observation is a direct result of the strong interfacial bond caused by the acid/water condition used in the fiber pretreatment. Evidence from coupling chemistry, rheological and electron microscopic studies support the above conclusion. When SEBS‐g‐MA copolymer is used, a synergistic toughening effect between the wood fiber and the copolymer is observed. The V‐notch Charpy impact strength of the WF/PP/SEBS‐g‐MA composite is substantially higher than that of the WF/PP composite. The synergistic toughening mechanisms are discussed with respect to the interfacial bond strength, fiber‐matrix debonding, and matrix plastic deformation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1000–1010, 2000     

The property of polycarbonate/acrylonitrile butadiene styrene‐based conductive composites filled by nickel‐coated carbon fiber and nickel–graphite powder

The filled conductive composites were prepared with a polycarbonate/acrylonitrile butadiene styrene matrix and both nickel‐coated carbon fiber (NiCF) and nickel–graphite powder (NCG) as fillers by using injection molding and injection‐compression molding. The effect of the NiCF content, NCG content, coupling agent, and molding methods on the properties of composites was studied. The results showed that the conductivity of the composites increased with raising the NiCF content and NCG content. NiCF treated with silane coupling agent could further improve the conductivity of the composites without any significant change in mechanical properties. Furthermore, compared with injection molding, the composites prepared by injection‐compression molding possessed better conductivity. POLYM. COMPOS., 38:157–163, 2017. © 2015 Society of Plastics Engineers     

Effect of fiber treatment on the mechanical properties of hybrid fiber reinforced polystyrene composites. Part II. Use of glass fiber and wood pulp as hybrid fiber

The mechanical properties of polystyrene reinforced with a mixture of hardwood aspen chemithermomechanical pulp (CTMP) and surface-treated glass fiber have been studied. The adhesion of cellulose fiber to glass fiber as well as to thermoplastics improved thanks to various surface treatments of CTMP, e.g. coating with polymer+isocyanate or with silane, and grafting with polystyrene. In general, compared with non-treated CTMP-filled composites, the mechanical properties improved when surface-treated wood fiber was used as a filler. Experimental results indicate better compatibility between treated wood fiber and surface-treated glass fiber as well as polystyrene and, consequently, the mechanical properties were enhanced.