Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.     

Comparison of micelles formed by amphiphilic poly(ethylene glycol)‐b‐poly(trimethylene carbonate) star block copolymers

In this article, we describe the synthesis and solution properties of PEG‐b‐PTMC star block copolymers via ring‐opening polymerization (ROP) of trimethylene carbonate (TMC) monomer initiated at the hydroxyl end group of the core PEG using HCl Et₂O as a monomer activator. The ROP of TMC was performed to synthesize PEG‐b‐PTMC star block copolymers with one, two, four, and eight arms. The PEG‐b‐PTMC star block copolymers with same ratio of between hydrophobic PTMC and hydrophilic PEG segments were obtained in quantitative yield and exhibited monomodal GPC curves. The amphiphilic PEG‐b‐PTMC star block copolymers formed spherical micelles with a core–shell structure in an aqueous phase. The mean hydrodynamic diameters of the micelles increased from 17 to 194 nm with increasing arm number. As arm number increased, the critical micelle concentration (CMC) of the PEG‐b‐PTMC star block copolymers increased from 3.1 × 10^?3 to 21.1 × 10^?3 mg/mL but the partition equilibrium constant, which is an indicator of the hydrophobicity of the micelles of the PEG‐b‐PTMC star block copolymers in aqueous media, decreased from 4.44 × 10⁴ to 1.34 × 10⁴. In conclusion, we confirmed that the PEG‐b‐PTMC star block copolymers form micelles and, hence, may be potential hydrophobic drug delivery vehicles. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Enhanced dynamic mechanical and shape‐memory properties of a poly(ethylene terephthalate)–poly(ethylene glycol) copolymer crosslinked by maleic anhydride

Dimethyl terephthalate (DMT) and ethylene glycol (EG) were used for the preparation of poly(ethylene terephthalate) (PET), and poly(ethylene glycol) (PEG) was added as a soft segment to prepare a PET–PEG copolymer with a shape‐memory function. MWs of the PEG used were 200, 400, 600, and 1000 g/mol, and various molar ratios of EG and PEG were tried. Their tensile and shape‐memory properties were compared at various points. The glass‐transition and melting temperatures of PET–PEG copolymers decreased with increasing PEG molecular weight and content. A tensile test showed that the most ideal mechanical properties were obtained when the molar ratio of EG and PEG was set to 80:20 with 200 g/mol of PEG. The shape memory of the copolymer with maleic anhydride (MAH) as a crosslinking agent was also tested in terms of shape retention and shape recovery rate. The amount of MAH added was between 0.5 and 2.5 mol % with respect to DMT, and tensile properties and shape retention and recovery rate generally improved with increasing MAH. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 27–37, 2002     

聚乙二醇/聚己内酯三嵌段共聚物的合成与表征

以甲苯二异氰酸酯 (TDI)为偶联剂 ,合成了聚乙二醇 (PEG) /聚己内酯 (PCL)两亲性三嵌段共聚物 (PEG-b-PCL -b -PEG ,PECL) ,采用IR、1 H-NMR、DSC和WAXD分析和研究了PECL的结构与性能。实验结果表明 ,PECL的结构和组成与设计相一致 ,结晶度和熔点均低于均聚物 ,且随着PECL中PCL嵌段含量的增加 ,PCL嵌段熔点升高。透射电镜照片显示PECL纳米粒呈核 /壳结构的球形。     

Surface modification of poly(ethylene terephthalate) film by coating with poly(ethylene glycol)‐grafted polystyrene

The poly(ethylene glycol) (PEG)‐grafted styrene (St) copolymer, which was formed as a nanosphere, was used as an agent to modify the surface of poly(ethylene terephthalate) (PET) film. The graft copolymer was dissolved into chloroform and coated onto the PET film by dip–coating method. The coated amount depends on the content ratios of PEG and St, the solution concentration, and the coating cycles. The graft copolymers having a low molecular weight of PEG‐ or St‐rich content was fairly stable on washing in sodium dodecyl sulfate (SDS) aqueous solution. It was confirmed that the PET surface easily altered its surface property by the coating of the graft copolymers. The contact angles of the films coated with the graft copolymers were very high (ca. 105–120°). The coated film has good antistatic electric property, which agreed with PEG content. The best condition of coating is a one‐cycle coating of 1% (w/v) graft copolymer solution. The coated surface had water‐repellency and antistatic electric property at the same time. The graft copolymer consisted of a PEG macromonomer; St was successfully coated onto PET surfaces, and the desirable properties of both of PEG macromonomer and PSt were exhibited as a novel function of the coated PE film. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1524–1530, 1999     

新型药物载体聚乙烯-聚丙交酯载药颗粒的制备及表征

Methoxy poly （ethylene glycol） -poly （D, L-lactide） block copolymers （PEG-PLA） were prepared through ring-opening polymerization. The oil in water suspension method was used to prepare block copolymer micelles. The critical micelle concentration （CMC） by fluorescence spectroscopy was 0. 0056 mg· ml^- 1. The physical state of the inner core region of micelles was characterized with ^1 HNMR. The size of indomethacin （IMC） loaded micelles measured by dynamic light scattering （DLS） showed narrow monodisperse size distribution and the average diameters were less than 50 nm. In addition, the nanoparticles with relatively high drug loading content （DLC） were obtained.     

Preparation and characterization of poly(ethylene glycol) crosslinked chitosan films

Poly(ethylene glycol) (PEG) crosslinked chitosan films with various PEG to chitosan ratio and PEG molecular weight were successfully prepared via the epoxy‐amine reaction between chitosan and PEG‐epoxy. The thermal and mechanical properties and swelling behavior were studied for the PEG crosslinked chitosan films. The mechanical strength of chitosan films were greatly enforced by the introduction of PEG‐epoxy, achieving an elongation of about 80%. It was found that the crosslinked chitosan films form hydrogel in water, achieving a swelling ratio higher than 20 times of original weight. The swelling behavior of chitosan films relied greatly on the molecular weight of the crosslinker PEG‐epoxy and the weight percent of PEG‐epoxy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

异端基遥爪聚乙二醇的合成

采用3种新式引发剂,即2-(苄氧基）乙醇钾、2-(四氢-2H-吡喃-2-氧基)乙醇钾、单丙烯基乙二醇钾引发环氧乙烷阴离子开环聚合,反应条件为25 ℃、48 h、醇与萘钾摩尔比例1∶1,得到3种异端基遥爪聚乙二醇。以2-(苄氧基）乙醇钾引发聚合所得产物为起始物,经一系列反应,得到两种两端均为活性基团的异端基遥爪聚乙二醇,这种方法具有普适性。通过1HNMR及GPC手段,表征了产物的结构、分子量及分子量分布。结果表明可以得到高产率、分子量可控且分布窄的异端基遥爪聚乙二醇。     

Unsaturated polyester resin via chemical recycling of off‐grade poly(ethylene terephthalate)

BACKGROUND: The chemical recycling of poly(ethylene terephthalate) (PET), e.g. bottles and fibre wastes, has been studied for many years. Among several methods proposed for chemical recycling of waste PET, glycolysis makes it possible to employ very low amounts of reactants and lower temperatures and pressures compared with critical methanol and thermal degradation. Furthermore, unlike hydrolysis under acidic or basic conditions, glycolysis does not cause any problems related to corrosion and pollution. RESULTS: PET from off‐grades of industrial manufacture was depolymerized using excess glycol. The effects of the reaction time, volume of glycol and catalyst concentrations on the yield of the glycolysis products were investigated. A reaction time of 3 h, weight ratio (catalyst to PET) of 0.25 wt% and PET to ethylene glycol molar ratio of 1:5 were determined as suitable conditions for depolymerization. Then, the reaction of polyesterification of maleic anhydride (MA) and glycolysed products of PET was successfully performed at 160 and 190 °C for 8 h. CONCLUSION: Differential scanning calorimetry and vapour pressure osmometry results for the product of the glycolysis reactions, under suitable condition, confirmed the structure of the desired product. This sample underwent reaction with MA to produce unsaturated polyester resin (UPR). The results of Fourier transform infrared and NMR spectroscopy confirmed that the UPR had been synthesized successfully. This is the first direct report on the glycolysis reaction of off‐grade products of petrochemical companies in order to regenerate raw materials or other secondary value‐added products. Copyright © 2009 Society of Chemical Industry     

Biodegradable polymer blends of poly(lactic acid) and poly(ethylene glycol)

Poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG) were melt-blended and extruded into films in the PLA/PEG ratios of 100/0, 90/10, 70/30, 50/50, and 30/70. It was concluded from the differential scanning calorimetry and dynamic mechanical analysis results that PLA/PEG blends range from miscible to partially miscible, depending on the concentration. Below 50% PEG content the PEG plasticized the PLA, yielding higher elongations and lower modulus values. Above 50% PEG content the blend morphology was driven by the increasing crystallinity of PEG, resulting in an increase in modulus and a corresponding decrease in elongation at break. The tensile strength was found to decrease in a linear fashion with increasing PEG content. Results obtained from enzymatic degradation show that the weight loss for all of the blends was significantly greater than that for the pure PLA. When the PEG content was 30% or lower, weight loss was found to be primarily due to enzymatic degradation of the PLA. Above 30% PEG content, the weight loss was found to be mainly due to the dissolution of PEG. During hydrolytic degradation, for PLA/PEG blends up to 30% PEG, weight loss occurs as a combination of degradation of PLA and dissolution of PEG. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1495–1505, 1997     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers

Poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers with predetermined block lengths were synthesized by polycondensation of PLA diols and PEG diacids. The reaction was carried out under mild conditions, using dicyclohexylcarbodiimide as the coupling agent and dimethylaminopyridine as the catalyst. The resulting copolymers were characterized by various analytical techniques, such as GPC, viscometry, ¹H‐NMR, FTIR, DSC, X‐ray diffractometry, and contact angle measurement. The results indicated that these copolymers presented outstanding properties pertinent to biomedical use, including better miscibility between the two components, low crystallinity, and hydrophilicity. Moreover, the properties of the copolymers can be modulated by adjusting the block length of the two components or the reaction conditions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1729–1736, 2002; DOI 10.1002/app.10580     

ABA triblock copolymers from poly(p‐dioxanone) and poly(ethylene glycol)

Poly(p‐dioxanone)–poly(ethylene glycol)–poly(p‐dioxanone) ABA triblock copolymers (PEDO) were synthesized by ring‐opening polymerization from p‐dioxanone using poly(ethylene glycol) (PEG) with different molecular weights as macroinitiators in N₂ atmosphere. The copolymer was characterized by ¹H NMR spectroscope. The thermal behavior, crystallization, and thermal stability of these copolymers were investigated by differential scanning calorimetry and thermogravimetric measurements. The water absorption of these copolymers was also measured. The results indicated that the content and length of PEG chain have a greater effect on the properties of copolymers. This kind of biodegradable copolymer will find a potential application in biomedical materials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1092–1097, 2006     

Miscibility of polystyrene with poly(ethylene oxide) and poly(ethylene glycol)

The intrinsic viscosity of polystyrene–poly(ethylene oxide) (PS–PEO) and PS–poly(ethylene glycol) (PEG) blends have been measured in benzene as a function of blend composition for various molecular weights of PEO and PEG at 303.15 K. The compatibility of polymer pairs in solution were determined on the basis of the interaction parameter term, Δb, and the difference between the experimental and theoretical weight-average intrinsic viscosities of the two polymers, Δ[η]. The theoretical weight-average intrinsic viscosities were calculated by interpolation of the individual intrinsic viscosities of the blend components. The compatibility data based on [η] determined by a single specific viscosity measurement, as a quick method for the determination of the intrinsic viscosity, were compared with that obtained from [η] determined via the Huggins equation. The effect of molecular weights of the blend components and the polymer structure on the extent of compatibility was studied. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1471–1482, 1998     

Modification of zein films by incorporation of poly(ethylene glycol)s

The thermal and mechanical properties of corn (maize) (CZ) films plasticized with poly(ethylene glycol) (PEG) of two different molar masses (400 and 1000 g mol⁻¹) were studied using differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), tensile strength, moisture absorption isotherms and water vapour transmission rate measurements. The glass transition temperature (T_g) of plasticized films is determined primarily by the amount of moisture contained in the film. DMTA data show contraction of films with loss of absorbed water during heating/cooling cycles. The moisture absorption behaviour of films plasticized with PEG400 and PEG1000 is similar at low relative humidities but significantly different at higher relative humidities. Incorporation of up to about 30 wt% PEG substantially enhances the tensile strength and the resistance to water vapour transmission of the protein film, and PEG1000 is more effective than PEG400. © 2000 Society of Chemical Industry     

Synthesis of unsaturated poly(ether amide)s based on amine‐terminated poly(ethylene glycol)

Novel water‐soluble unsaturated poly(ether amide)s (PEAs) were synthesized by low‐temperature polycondensation of fumaryl chloride and amine‐terminated poly(ethylene glycol) (Jeffamine®). The unsaturated copolymers were further chemically modified with thiols to provide reactive pendant functional groups. Hydrogels based on these copolymers were prepared by copolymerization of the PEA with N‐vinyl pyrrolidone exposure to ultraviolet (UV) irradiation. The resulting hydrogels exhibited a high swelling ratio, and the magnitude of swelling depended on the molecular weight of Jeffamine®. The swelling ratio and equilibrium water content tended to increase with increasing chain length of the Jeffamine® used in copolymer synthesis. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 913–920, 1999     

Synthesis and property evaluations of photocrosslinkable chitosan derivative and its photocopolymerization with poly(ethylene glycol)

Photocrosslinkable polymers are clean and convenient materials for the biomedical uses. Chitosan, which owns excellent biocompatible and antimicrobial properties, is one of the choices while it is introduced with photosensitive functional groups. In this study, chitosan was N‐phthaloylated to react with acryloyl chloride in the organic solvent homogeneously and the result has been verified by the solubility test. Fourier transformed infrared spectrometry and nuclear magnetic resonance spectrometer analysis indicated that the modification with the attachment of the photosensitive functional group, the acryloyl group, onto chitosan and poly(ethylene glycol) (PEG) was feasible. The differential scanning calorimetry analysis further indicated that the melting points of the N‐phathaloylated chitosan were decreased as compared with the untreated chitosan control. Then photocrosslinkable chitosan derivative (CH‐PAA) was photocopolymerized with PEG diacrylate (PEGA) under UV irradiation. The adhesion strength characterization and swelling capacity evaluation for this photocopolymer have shown obvious raises of the adhesiveness and water‐adsorption abilities as compared with the photopolymer of CH‐PAA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1794–1801, 2006     

含聚乙二醇的嵌段共聚物的合成及自组装研究进展

综述了通过活性自由基聚合如原子转移自由基聚合（ATRP）、氮氧稳定自由基聚合（NMP）、可逆加成断裂链转移聚合（RAFT）等方法合成含聚乙二醇（PEG）的嵌段共聚物的研究进展,并对含PEG类嵌段共聚物在溶液中的自组装技术和在药物载体、介孔材料以及碳纳米管中的应用进行了归纳,指出含PEG的嵌段共聚物可以自组装成多种形貌,直接影响材料的性能和应用,所以这些结构有潜在的应用价值和应用前景,并且合成新的含PEG的嵌段共聚物和开发具有新型结构、形貌可控的自组装体以及新的应用领域是今后的一个热点问题,具有重要的科学研究意义和实际应用价值。     

Poly(ethylene glycol) electrolyte gels prepared by condensation reaction

Poly(ethylene glycol) electrolyte gels were prepared by condensation reaction in the presence of tetraethoxysilane. Differential scanning calorimetry and X‐ray diffraction spectroscopy were used to investigate the thermal transition behavior and crystalline structure of polymer gels prepared. Both formation of crosslinks and incorporation of salts or plasticizers reduced the development of crystalline structure of poly(ethylene glycol)s. Cyclic voltammetric and ion‐conducting behaviors of polymer gels were analyzed using potentiostat and impedance spectroscopy, and those were also considerably affected by the crosslinking density of polymers and the concentration of electrolyte salt or plasticizers incorporated. Poly(ethylene glycol) gels possessing certain levels of electrolyte salt and plasticizer were expected to have applications of solid electrolytes for lithium polymer secondary batteries. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 948–956, 2002     

Effect of antioxidant contained in poly(ethylene glycol) on cell fusion

The effect of antioxidants contained in poly(ethylene glycol) (PEG) on cell fusion was studied using L929 cells in the monolayer state. Hydroquinone monomethyl ether (HQME), 2-mercaptobenzimidazole (MB), butyl hydroxyanisole (BHA) and 2,6-di-(t-butyl)-4-methylphenol (BHT) were chosen from the antioxidants that have currently been used to protect commercially available PEG from oxidation. Cell culture was conducted in 40% w/w aqueous solution of PEG with a molecular weight of 3000 in the presence of different concentrations of antioxidants. BHA clearly enhanced membrane fusion of L929 cells with increasing concentration in PEG solution, whereas HQME, MB and BHT had no significant effect on cell fusion. The enhancement of cell fusion by BHA might be ascribed to balanced hydrophobicity and high water solubility in comparison with the other three antioxidants.