Comparative study of a three-bucket Savonius rotor with a combined three-bucket Savonius–three-bladed Darrieus rotor

The vertical axis wind turbines are simple in construction, self-starting, inexpensive and can accept wind from any direction without orientation. A combined Savonius–Darrieus type vertical axis wind rotor has got many advantages over individual Savonius or individual Darrieus wind rotor, such as better efficiency than Savonius rotor and high starting torque than Darrieus rotor. But works on the combined Savonius–Darrieus wind rotor are very scare. In view of the above, two types of models, one simple Savonius and the other combined Savonius–Darrieus wind rotors were designed and fabricated. The Savonius rotor was a three-bucket system having provisions for overlap variations. The Savonius–Darrieus rotor was a combination of three-bucket Savonius and three-bladed Darrieus rotors with the Savonius placed on top of the Darrieus rotor. The overlap variation was made in the upper part, i.e. the Savonius rotor only. These were tested in a subsonic wind tunnel available in the department. The various parameters namely, power coefficients and torque coefficients were calculated for both overlap and without overlap conditions. From the present investigation, it is seen that with the increase of overlap, the power coefficients start decreasing. The maximum power coefficient of 51% is obtained at no overlap condition. However, while comparing the power coefficients (C_p) for simple Savonius-rotor with that of the combined configuration of Savonius–Darrieus rotor, it is observed that there is a definite improvement in the power coefficient for the combined Savonius–Darrieus rotor without overlap condition. Combined rotor without overlap condition provided an efficiency of 0.51, which is higher than the efficiency of the Savonius rotor at any overlap positions under the same test conditions.     

Aerodynamic performance prediction of a 30 kW counter-rotating wind turbine system

In the present work, the aerodynamic performance prediction of a unique 30 kW counter-rotating (C/R) wind turbine system, which consists of the main rotor and the auxiliary rotor, has been investigated by using the quasi-steady strip theory. The near wake behavior of the auxiliary rotor that is located upwind of the main rotor is taken into consideration in the performance analysis of the turbine system by using the wind tunnel test data obtained for scaled model rotors. The relative size and the optimum placement of the two rotors are investigated through use of the momentum theory combined with the experimental wake model. In addition, the performance prediction results along with the full-scale field test data obtained for C/R wind turbine system are compared with those of the conventional single rotor system and demonstrated the effectiveness of the current C/R turbine system.     

The Darrieus wind turbine: Proposal for a new performance prediction model based on CFD

This paper presents a CFD model for the evaluation of energy performance and aerodynamic forces acting on a straight-bladed vertical-axis Darrieus wind turbine. The basic principles which are currently applied to BE-M theory for rotor performance prediction are transferred to the CFD code, allowing the correlation between flow geometric characteristics (such as blade angles of attack) and dynamic quantities (such as rotor torque and blade tangential and normal forces). The model is proposed as a powerful design and optimization tool for the development of new rotor architectures for which test data is not available.After describing and validating the computational model against experimental data, a full campaign of simulation is proposed for a classical NACA 0021 three-bladed rotor.Flow field characteristics are investigated for several values of tip speed ratio, allowing a comparison among rotor operation at optimum and lower C_p values, so that a better understanding of vertical-axis wind turbines basic physics is obtained.     

A vortex model for Darrieus turbine using finite element techniques

Since 1970 several aerodynamic prediction models have been formulated for the Darrieus turbine. We can identify two families of models: stream-tube and vortex. The former needs much less computation time but the latter is more accurate. The purpose of this paper is to show a new option for modelling the aerodynamic behaviour of Darrieus turbines. The idea is to combine a classic free vortex model with a finite element analysis of the flow in the surroundings of the blades. This avoids some of the remaining deficiencies in classic vortex models. The agreement between analysis and experiment when predicting instantaneous blade forces and near wake flow behind the rotor is better than the one obtained in previous models.     

Simulation of wind turbine wake interaction using the vorticity transport model

The aerodynamic interactions that can occur within a wind farm can result in the constituent turbines generating a lower power output than would be possible if each of the turbines were operated in isolation. Tightening of the constraints on the siting of wind farms is likely to increase the scale of the problem in the future. The aerodynamic performance of turbine rotors and the mechanisms that couple the fluid dynamics of multiple rotors can be most readily understood by simplifying the problem and considering the interaction between only two rotors. The aerodynamic interaction between two rotors in both co‐axial and offset configurations has been simulated using the Vorticity Transport Model. The aerodynamic interaction is a function of the tip speed ratio, and both the streamwise and crosswind separation between the rotors. The simulations show that the momentum deficit at a turbine operating within the wake developed by the rotor of a second turbine is governed by the development of instabilities within the wake of the upwind rotor, and the ensuing structure of the wake as it impinges on the downwind rotor. If the wind farm configuration or wind conditions are such that a turbine rotor is subject to partial impingement by the wake produced by an upstream turbine, then significant unsteadiness in the aerodynamic loading on the rotor blades of the downwind turbine can result, and this unsteadiness can have considerable implications for the fatigue life of the blade structure and rotor hub. Copyright © 2009 John Wiley & Sons, Ltd.     

Aerodynamic wind-turbine rotor design using surrogate modeling and three-dimensional viscous–inviscid interaction technique

In this paper a surrogate optimization methodology using a three-dimensional viscous-inviscid interaction code for the aerodynamic design of wind-turbine rotors is presented. The framework presents a unique approach because it does not require the commonly-used blade element momentum (BEM) method. The three-dimensional viscous-inviscid interaction code used here is the accurate and fast MIRAS code developed at the Technical University of Denmark. In comparison with BEM, MIRAS is a higher-fidelity aerodynamic tool and thus more computationally expensive as well. Designing a rotor using MIRAS instead of an inexpensive BEM code represents a challenge, which is resolved by using the proposed surrogate-based approach. As a verification case, the methodology is applied to design a model wind-turbine rotor and is compared in detail with the one designed with BEM. Results demonstrate that nearly identical aerodynamic performance can be achieved using the new design method and that the methodology is effective for the aerodynamic design of wind-turbine rotors.     

On the aerodynamics of variable-geometry oval-trajectory Darrieus wind turbines

A new computational model for the aerodynamics of vertical-axis wind turbines is introduced. It is based on the double-multiple streamtube concept and it incorporates the capacity of dealing with rotors whose blades follow oval-trajectories at variable setting-angles. We applied this model to the study of the aerodynamics of an innovative concept in extra-large wind-power plants: the VGOT (variable-geometry oval-trajectory) Darrieus wind turbine. Due to the especial geometric characteristics of the VGOT Darrieus, it was necessary to propose three new non-dimensional parameters to quantify its performance under different wind-conditions: the equivalent power coefficient, the equivalent solidity coefficient and the trajectory efficiency. We show some numerical results testing several rotor configurations working under different wind scenarios.     

Shape optimization of wind turbine blades

This paper presents a design tool for optimizing wind turbine blades. The design model is based on an aerodynamic/aero‐elastic code that includes the structural dynamics of the blades and the Blade Element Momentum (BEM) theory. To model the main aero‐elastic behaviour of a real wind turbine, the code employs 11 basic degrees of freedom corresponding to 11 elastic structural equations. In the BEM theory, a refined tip loss correction model is used. The objective of the optimization model is to minimize the cost of energy which is calculated from the annual energy production and the cost of the rotor. The design variables used in the current study are the blade shape parameters, including chord, twist and relative thickness. To validate the implementation of the aerodynamic/aero‐elastic model, the computed aerodynamic results are compared to experimental data for the experimental rotor used in the European Commision‐sponsored project Model Experiments in Controlled Conditions, (MEXICO) and the computed aero‐elastic results are examined against the FLEX code for flow past the Tjæreborg 2 MW rotor. To illustrate the optimization technique, three wind turbine rotors of different sizes (the MEXICO 25 kW experimental rotor, the Tjæreborg 2 MW rotor and the NREL 5 MW virtual rotor) are applied. The results show that the optimization model can reduce the cost of energy of the original rotors, especially for the investigated 2 MW and 5 MW rotors. Copyright © 2009 John Wiley & Sons, Ltd.     

实度对低风速风电机组风轮气动性能影响研究

为提高低风速地区的风能利用率,研究风轮实度对低风速风电机组气动性能的影响。考虑影响风轮实度因素（叶片数量、弦长及安装角）,设计2组不同弦长叶片与可调安装角轮毂。安装角改变时不仅会引起实度变化,还会使叶尖速比发生改变。通过车载试验验证安装角不同时对风轮气动性能的影响主要与叶尖速比相关。根据不同风轮表面压力分布数值模拟结果得出：相同风速下,弦长由叶根到叶尖逐渐增大的叶片更易启动。相同条件下,试验机组输出功率与数值模拟机组输出功率最大相差5.37%,说明数值模拟结果可信。随着风轮实度的增加,风速5 m/s时,其风能利用系数呈增大趋势,风速8 m/s时,其风能利用系数呈减小趋势,两趋势相交时实度为25.38%,得出该实度下风轮气动性能较优,即可得到适合低风速地区的风轮实度。     

高负荷扩压串列转子的设计技术探讨

对高负荷串列转子的设计技术进行了探讨,通过速度三角形分析与可控扩散叶型的反问题设计技术相结合,完成了二维高负荷串列转子的设计方案。数值计算表明:所设计的串列转子有优越的气动性能,效率能达到91%,并且在50°的气流弯折角和1.68的增压比情况下无分离流动,保证了其做功能力达到了原始两级的做功能力。