载荷和转速对HDPE多元复合材料摩擦学性能的影响

为改善高密度聚乙烯(HDPE)的力学性能、自润滑性和耐磨性,以HDPE为基体,通过填充六钛酸钾晶须(PTW)、聚四氟乙烯(PTFE)和滑石粉制备一种HDPE复合材料.在MMW-1型摩擦磨损试验机上测试复合材料在不同载荷和转速下的摩擦因数、磨损率,采用扫描电镜(SEM)分析磨痕形貌,探讨HDPE复合材料的摩擦磨损规律.结...     

纳米SiO2颗粒和玻璃微珠共混改性超高分子量聚乙烯复合材料的摩擦磨损性能

采用模压成型工艺制备了纳米SiO2颗粒和玻璃微珠共混改性的超高分子量聚乙烯复合材料;研究了相对滑动速度、载荷以及玻璃微珠含量对复合材料摩擦磨损性能的影响,并对磨损形貌和磨损机理进行了分析。结果表明:添加纳米SiO2颗粒和玻璃微珠可以提高复合材料的硬度、压缩弹性模量和摩擦磨损性能;相对滑动速度对复合材料摩擦因数和磨损率有很大的影响;载荷对复合材料的摩擦因数影响不明显,但磨损率随载荷的增加而增大;纳米SiO2颗粒和玻璃微珠混合改性后复合材料的磨损机理主要是粘着磨损和疲劳磨损。     

铜镍锡合金干滑动磨损行为研究*

大型装备上的铜镍锡合金工件常常工作在润滑不足或者无润滑的工况条件下,因此有必要研究铜镍锡材料在干摩擦下的性能。采用CEF-I型销-盘式磨损试验机对铜镍锡合金在不同载荷与转速条件下进行干滑动摩擦磨损试验,采用扫面电子显微镜、能谱仪和轮廓检测仪对磨损表面进行检测,研究铜镍锡合金的干滑动磨损行为,并探讨其磨损机制。结果表明：在转速一定时,平均摩擦因数随载荷增大总体呈波动下降趋势,铜镍锡合金试件磨损量先缓慢增加,在较高载荷下快速增加;在载荷一定时,平均摩擦因数随转速增大先增大后减小,铜镍锡合金试件磨损量总体呈先减小后增大趋势;随着载荷的增大,铜镍锡合金的磨损机制由轻微黏着和剥层磨损到明显的黏着和剥层磨损,再到严重的黏着和疲劳磨损,随着转速的增大,铜镍锡合金的磨损机制由磨粒磨损转变为黏着磨损再到剥层磨损。在较低载荷下,随着转速的增大,铜镍锡合金摩擦磨损性能保持很好的稳定性,因此铜镍锡合金适用在高转速较低载荷的干摩擦工况下。     

载流条件下的1Cr18Ni9Ti/浸金属碳摩擦磨损性能研究

在销-盘摩擦磨损试验机上试验了载荷、速度、电流对1Cr18Ni9Ti/浸金属碳对磨时的摩擦因数、磨损量及磨损形貌的影响。试验结果表明,载荷对1Cr18Ni9Ti/浸金属碳摩擦副的摩擦因数和销试样的磨损率有显著影响:载荷越大,摩擦因数越大,磨损率越低;摩擦因数、磨损率与速度的关系受载荷的制约。当低载时,以电流影响为主。销试样的磨损表面出现了粘着磨损,氧化磨损和电弧烧蚀。     

铜碲硒铁合金的干摩擦磨损性能

利用环-盘式摩擦磨损试验机研究了铜碲硒铁合金的干摩擦磨损行为,分析了载荷和摩擦速度等参数对该合金摩擦磨损性能的影响,并用扫描电子显微镜对磨损形貌进行了观察.结果表明:铜碲硒铁合金的摩擦因数随载荷的增加变化不大,但随摩擦速度的增加而明显增大;合金的磨损率随载荷和摩擦速度的增加均增大;在轻载低速条件下,合金的磨损机制以犁削磨损和粘着磨损为主;在重载高速条件下,磨粒磨损和粘着磨损加剧.     

An Analysis and Comparison of the Tribological Behavior of Two Polymers Sliding Against a Polymeric Composite

Two polymers, ultrahigh-molecular-weight polyethylene (UHMWPE) and polycarbonate, were slid dry against continuous fiber graphite/epoxy composites in multiple-pass friction and wear tests. High and low valves of load, speed, fiber orientation, and virgin surface roughness were used to find their effect on the coefficient of friction and wear rate. Regression equations were developed from the data to help describe the effects of various independent variables. For the total distance slid of 176 m, there was no significant effect of sliding speed on coefficient of friction. The coefficient of friction for UHMWPE was found to depend on surface roughness and fiber orientation. For polycarbonate, the coefficient of friction was very complex, containing a three-factor interaction between normal load, surface roughness, and fiber orientation. The wear rate for UHMWPE was a function of normal load, surface roughness, and a nonlinear term in normal load and surface roughness. The wear rate for polycarbonate was significantly affected by all variables except fiber orientation.     

AZ91D镁合金微动磨损特性研究

采用液压高精度材料试验机考察了平面一球面接触的AZ91D镁合金摩擦副的微动磨损行为，分析了位移幅值、法向载荷和频率等参数对摩擦因数和磨损体积的影响，考察了不同实验条件下的磨斑形貌，并探讨了其磨损机理。结果表明：AZ91D镁合金的微动区域可分为部分滑移区、混合区和滑移区3个区域，粘着磨损、疲劳磨损和磨粒磨损分别是3个区域的主要磨损机制；磨损体积随着位移幅值和法向载荷的增加而增大，但却随着频率的增大而减小。在微动部分滑移区和混合区，摩擦因数随着位移增大迅速增加；在微动滑移区，摩擦因数随法向载荷的增大而减小，而位移幅值和频率对摩擦因数的影响较小。     

Friction and Wear Behavior of Irradiated Polyethylene Sliding Against a Rough Steel Surface

The aim of this study was to evaluate the tribological behavior of polyethylene crosslinked by gamma radiation sliding against a steel surface. Two high-density polyethylenes were irradiated to a total dose in the range of 2?20 Mrad under vacuum and at room temperature. After irradiation, the materials were annealed at 423 K and then cooled slowly to room temperature. The same thermal treatment was applied to the non-irradiated polymer. The wear behavior of the polymers was determined under controlled ambient temperature of 298 and 333 K using a homemade tribometer. Sheet-shaped specimens were loaded against the surface of a steel disc with different normal loads to generate nominal contact pressures in the range of 0.25–1.5 MPa. The tests were performed under dry conditions using a disc rotation to produce an average sliding speed of 0.6 m/s and during a period of time to provide an average sliding distance of 1,080 m. The wear rate was obtained as the mass loss by the sample divided by the sliding distance, and the friction coefficient was determined by measuring the friction force. The results indicate that the wear rate increases with load in the case of non-irradiated polyethylene and low-dose irradiated polymers, while the wear rate reaches a maximum value with the load in the case of the irradiated samples with high doses. The samples irradiated with a dose of 10 Mrad showed the lowest wear. The coefficient of friction (COF) increases slightly with the load in all the cases. Most irradiated polymers show higher COF than the non-irradiated material when compared at a given load. The results show that the irradiation dose applied to the polyethylenes produced no noticeable effect on the COF values when a comparison was made at a given applied load.     

晶粒尺寸对WC硬质合金刀具材料摩擦磨损性能的影响

研究了三种不同晶粒尺寸的硬质合金材料的摩擦磨损性能,测量了摩擦系数,采用扫描电子显微镜观察分析了硬质合金磨损表面的形貌变化。结果表明,随着滑动速度和载荷的提高,硬质合金的摩擦系数呈下降的趋势;相同条件下,随着晶粒的减小,硬质合金的摩擦系数略有升高。粗晶粒的硬质合金主要磨损机制为WC晶粒脱落造成的磨粒磨损,细晶粒硬质合金磨损机制主要表现为塑性变形。     

Sliding-Wear Behavior of TiN- and CrN-Coated 2024 Aluminum Alloy Against an Al2O3 Ball

Dry sliding friction and wear behavior of TiN and CrN deposited on 2024 aluminum alloy by arc ion plating was investigated using the ball-on-disk wear test. The effects of normal load and ceramic coating on the friction coefficient and wear-resistance of 2024 aluminum alloy were studied. The worn surfaces were observed by scanning electron microscopy (SEM). The results show that wear volume increases while the friction coefficient decreases with an increase in normal load. The wear resistance of CrN is higher than that of TiN. The wear mechanism of TiN-coated 2024 Al is related to the oxidation of TiN coating and plastic deformation of 2024 Al. Conversely, the wear mechanism of CrN-coated 2024 Al is related to the fatigue fracture of the coating, which was affected by residual stress and plastic deformation of 2024 Al.     

Effect of contact pressure on wear and friction of ultra-high molecular weight polyethylene in multidirectional sliding

Computational wear models need input data from valid tribological tests. For the wear model of a total hip prosthesis, the contact pressure dependence of wear and friction of ultra-high molecular weight polyethylene (UHMWPE) against polished CoCr in diluted calf serum lubricant was studied, and useful input data produced. Two test devices were designed and built: a heavy load circularly translating pin-on-disc (HL-CTPOD) wear test device and an HL-CTPOD friction measurement device. Both can be used with a wide range of loads. The wear surface diameter of the test pin was kept constant at 9 mm, whereas the load was varied so that the nominal contact pressure ranged from 0.1 to 20 MPa. The wear factor decreased with increasing contact pressure, whereas the coefficient of friction first increased with increasing contact pressure with low pressure values and then decreased. Up to the pressure of 2.0 MPa, the wear mechanisms and wear factors were in good agreement with clinical findings. In the critical range of 2.0-3.5 MPa, the wear mechanisms and wear factors started to differ from clinical ones, and the decrease of the wear factor steepened. The discrepancy became more and more evident as the pressure was gradually increased beyond 3.5 MPa. It appears that the pressure value of 2.0 MPa should not be exceeded in pin-on-disc wear tests that are to reproduce the clinical wear of UHMWPE acetabular cups.     

Friction and Wear Behavior of Steels under Different Reciprocating Sliding Conditions

The friction and wear behavior of ISO 100Cr6 steel ball sliding against conventionally hardened carbon and low-alloy steels was studied. The effect of hardness, hardening capacity, normal load, and sliding speed on the coefficient of friction and friction energy was investigated. Friction tests were carried out, without lubrication and under ambient conditions, on a reciprocating friction tester in which a ball-on-flat contact configuration was adopted. The results showed that there is a relative tendency for the friction properties to decrease with increased hardening capacity and decreased hardness. The results showed that increasing normal load decreases the coefficient of friction for the two steel nuances. However, increasing sliding speed increases the coefficient of friction of low-alloy steel and decreases the coefficient of friction of carbon steel. The oxidation of wear debris influences the wear mechanisms and friction behavior.     

Ni-P-PTFE化学复合镀层的耐磨性能研究

制备了Ni-P-PTFE化学复合镀层,在MM-200型磨损试验机上研究了PTFE加入量、热处理温度和载荷对复合镀层摩擦因数和磨损量的影响。结果表明:镀层摩擦因数在PTFE加入量为8mL/L时最小,同时镀层磨损量在此时也最小;在不同热处理温度下,Ni-P-PTFE复合镀层表现出较好的耐磨性和较小的摩擦因数;当载荷超过98N后,镀层的摩擦因数增大;随着载荷的增大,镀层的磨损量增大。     

Tribological Behavior of NiAl–1.5 wt% Graphene Composite Under Different Velocities

The progress in aerospace field requires a new NiAl matrix composite that can stand against wear and decrease the energy dissipation through decreasing friction. In this study, the tribological behavior of NiAl–1.5 wt% graphene composite is investigated at room temperature under a constant load of 12 N and different sliding velocities. The results show that the friction coefficient and wear rate increase with increasing sliding velocity from 0.2 to 0.4 m/s due to the adhesion between the sliding bodies and tearing of the graphene layer. The friction coefficient and wear rate tend to decrease at a sliding velocity of 0.6 m/s as a result of severe plastic deformation and grain refinement of the worn surface. However, at 0.8 m/s the friction coefficient reaches a minimum value and the wear rate increases and changes the wear mechanism to fatigue wear. It can be concluded that various wear mechanisms lead to different tribological performance of NiAl–1.5 wt% graphene composite.     

Inconel718与硬质合金摩擦磨损特性的实验研究

利用UMT-2多功能摩擦磨损试验机对镍基合金Inconel 718与硬质合金刀具对偶时的摩擦磨损特性进行研究,揭示法向载荷和滑动速度对摩擦副摩擦因数的影响,通过SEM观察试样摩擦形貌并分析磨损机制.研究结果表明:摩擦副的摩擦因数随着法向载荷的增大而减小,随滑动速度的增大而增大;Inconel 718镍基合金与硬质合金对偶时的磨损机制主要为黏着磨损、磨粒磨损和氧化磨损.     

高水基液压阀陶瓷摩擦副摩擦学性能研究

为选择适合的高水基乳化液液压阀摩擦副材料,探讨ZrO2与不同结构陶瓷组成的摩擦副在高水基乳化液润滑状态下的摩擦磨损特性。采用摩擦磨损试验机,在不同载荷和滑动速度下,研究在高水基乳化液介质中4种不同陶瓷材料（ZrO2、Al2O3、Si3N4和SiC）分别与ZrO2配副的摩擦学性能,并探讨不同组合陶瓷摩擦副的磨损机制。结果表明：在高水基乳化液中,各陶瓷的摩擦因数均随着滑动速度的增大而降低,其中Al2O3陶瓷的摩擦因数最小;ZrO2、Al2O3和Si3N4陶瓷的摩擦因数受载荷的影响较小,SiC陶瓷的摩擦因数则随着载荷的增大而骤增;各陶瓷的磨损体积都随着速度和载荷的增大而增大,其中Al2O3/ZrO2陶瓷摩擦副的磨损体积最小,其磨损机制以磨粒磨损和微疲劳磨损为主。研究表明,在不同工况下,Al2O3与ZrO2陶瓷配副的摩擦因数和磨损体积均为最低值,更适合作为高水基乳化液液压阀的摩擦副材料。     

Tribological behavior of Al–Si–SiCp composites/automobile brake pad system under dry sliding conditions

Tribological behavior of stir-cast Al–Si/SiC_p composites against automobile brake pad material was studied using Pin-on-Disc tribo-tester. The Al-metal matrix composite (Al-MMC) material was used as disc, whereas the brake pad material forms the pin. It has been found that both wear rate and friction coefficient vary with both applied normal load and sliding speed. With increase in the applied normal load, the wear rate was observed to increase whereas the friction coefficient decreases. However, both the wear rate and friction coefficients were observed to vary proportionally with the sliding speed. During the wear tests, formation of a tribo-layer was observed, presence of which can affect the wear behavior, apart from acting as a source of wear debris. Tribo-layer formed over the worn disc surfaces was found to be heterogeneous in nature. Morphology and topography of worn surfaces and debris were studied using scanning electron microscope (SEM). Chemical composition of different wear products was obtained using electron probe micro analyzer (EPMA) and X-ray diffraction (XRD) techniques. Possible wear mechanisms operative in Al-MMC—brake pad tribo-couple have been discussed.     

Stick–Slip Friction of Stainless Steel in Sodium Dodecyl Sulfate Aqueous Solution in the Boundary Lubrication Regime

The service life of a diesel fuel injector is highly affected by the tribological properties of the fuel. This study aims to investigate the friction and wear behaviors of emulsified bio-oil (EBO), which is a very promising alternative fuel for engines. Sliding wear tests were performed with a ball-on-disk tribometer using a GCr15 steel ball and a flat specimen as a counterpart. In these tests, the total sliding distance was 500 m, the load ranged from 10 to 20 N, and the oscillation frequency ranged from 30 to 50 Hz. Experimental results showed that EBO had better tribological properties than diesel oil and crude bio-oil. Contact load and oscillation frequency significantly influenced friction coefficient, wear volume, and wear damage pattern. The friction coefficient decreased with an increase in load and increased with an increase in oscillation frequency. Furthermore, the wear volume slightly increased with an increase in load or oscillation frequency. The damage mechanism is attributed to adhesive wear under low load and to abrasive wear under high load. The transition in the wear mechanism is related to the adsorption of the molecules in the EBO, the microstructural contact surface, and the mechanical actions.     

高速摆动下PTFE编织复合材料干摩擦研究

利用高速摩擦试验机对PTFE编织复合材料进行干摩擦试验,研究不同条件(载荷、速度和湿度)下PTFE编织复合材料干摩擦磨损性能;并利用扫描电子显微镜对不同条件下的磨屑形貌进行分析。结果表明:单因素变化条件下,摩擦因数随载荷和相对湿度的增大而减小,随摩擦速度的增大而增大;磨损量随载荷和速度的增大而增大,但相对湿度的增加可降低磨损;载荷及速度的增加显著影响材料磨损状况。     

含硫化铜纳米粒子润滑脂的微动磨损性能研究

在微动磨损试验机上考察了含有硫化铜纳米粒子脲基脂的微动磨损性能。结果表明:硫化铜纳米粒子能显著降低微动磨损体积,随着纳米粒子含量增加,微动磨损量降低;在微动磨损后期纳米粒子的存在还能降低摩擦因数。低负荷下,润滑脂中硫化铜纳米粒子有利于降低微动磨损量;但在高负荷条件下,磨损量迅速增大,说明高负荷下微动磨损方式发生了变化。XPS分析表明,微动磨斑表面膜含有Cu、FeS等物质,说明硫化铜纳米粒子能显著降低微动磨损的原因在于纳米粒子化学性质非常活泼,在微动过程中容易与摩擦表面发生化学反应,形成具有保护性的沉积物膜和化学反应膜。