2.5维织物C_f/Al复合材料制备及其经纬向拉伸变形力学行为研究

以石墨纤维2.5维机织物为增强体,铝合金ZL301为基体材料,采用真空辅助压力浸渗法制备了2.5维织物Cf/Al复合材料,研究了3种织物预热温度下制备的复合材料相对致密度和微观组织形貌,分析了其界面产物组成与界面结构特征,测试了其经、纬向准静态拉伸变形力学行为并分析了其断口形貌。结果表明:复合材料织物的细观结构完整,内部纤维分布均匀,致密度随预热温度提高而略有上升,界面棒状产物为Al4C3相,其相对含量随预热温度的提高而增加,从而引起复合材料经向和纬向力学性能的下降。复合材料经向拉伸强度高于纬向拉伸强度,且其应力-应变行为呈现出显著的非线性特征,复合材料经向和纬向拉伸变形过程均可划分为3个阶段:初始弹性变形阶段、中间弹塑性变形阶段和最终损伤与断裂阶段。     

SiCf/SiC复合材料表面Si/Yb2Si2O7双层涂层结合强度分析

目的 通过选择合适的复合材料拉伸方向和涂层制备工艺,在SiCf/SiC复材上获得高结合强度的Si/Yb2Si2O7双层涂层.方法 采用真空等离子喷涂技术在2.5D编织的SiCf/SiC复合材料表面制备Si涂层、Si/Yb2Si2O7双层涂层.采用金相、XRD、SEM和EDS对试样进行表征,采用拉伸试验测试涂层的结合强度...     

热变形对烧结Cu-10wt.%WC复合材料组织及性能的影响

采用还原法制备Cu-10%WC复合粉末(质量分数),热压烧结得到Cu-10%WC复合材料,并进行热轧处理。采用扫描电子显微镜、X射线衍射仪、透射电子显微镜、拉伸试验等研究了热轧对Cu-10%WC复合材料组织和性能的影响及机理。结果表明,经热轧：复合材料中WC颗粒尺寸无变化但沿轧制方向重新排列;Cu晶粒尺寸减小,发生再结晶时沿(220)晶面择优生长,降低了与WC颗粒结合界面的错配度。轧制后,复合材料抗拉强度从426 MPa提高至492MPa,硬度HV_0.2从1467.1 MPa提高至1634.6 MPa,导电、导热性能不变。热轧使WC颗粒重新排列调节了位错的分布、Cu晶粒择优取向提高与WC颗粒界面结合强度以及细晶强化的作用,提高了复合材料综合性能。     

Improvement of strength of B／Al composite by thermal-mechanical cycling

The mechanical properties of B/Al composite were measured at room temperature in the as-fabricated condition and after thermal-mechanical cycling(TMC). The effects of TMC on microstructure and tensile fracture behavior of B/Al composite were studied using transmission electron microscope(TEM) and scanning electron microscope(SEM). The fibers/matrix interfaces are degraded during TMC, the extent of which is enhanced with increasing the cycles, causing a measurable decrease of stage I modulus of the B/Al composite. The TMC induces the dislocation generation in the aluminum matrix and the dislocation density increases with the cycles. The synergistic effect of the matrix strengthening and the interracial degradation during TMC is found to play an important role in controlling the changes of tensile strengths and fracture behavior of the composite. The ultimate tensile strength of the composite increases with the cycles increasing. The interfaces in the B/Al composite change from the stronglybonded states toward the appropriately-bonded ones with increasing the cycles. TMC will provide an approach of improving the strength of B/Al composites.     

Effects of dip-coated BN interphase on mechanical properties of SiCf/SiC composites prepared by CVI process

BN interphase was successfully synthesized on SiC fiber fabrics by dip-coating process using boric acid and urea as precursors under N₂ atmosphere. The morphology of BN interphase was observed by SEM, and the structure was characterized by XRD and FT-IR spectra. The SiC_f/SiC composites with dip-coated BN interphase were fabricated by chemical vapor infiltration (CVI) process, and the effects of BN interphase on the mechanical properties of composites were investigated. The results show that the SiC fibers are fully covered by BN interphase with smooth surface and turbostratic structure (t-BN), and the thickness is about 0.4 μm. The flexural strengths of SiC_f/SiC composites with and without BN interphase are about 180 and 95 MPa, respectively. Compared with the as-received SiC_f/SiC composites, the composites with BN interphase exhibit an obvious toughened fracture behavior. From the microstructural analysis, it can be confirmed that the BN interphase plays a key part in protecting the fibers from chemical attack during matrix infiltration and weakening interfacial bonding, which can improve the mechanical properties of SiC_f/SiC composites remarkably.     

Interfacial microstructure and properties of diamond/Cu-<Emphasis Type="Italic">x</Emphasis>Cr composites for electronic packaging applications

Diamond/Cu-xCr composites were fabricated by pressure infiltration process.The thermal conductivities of diamond/Cu-xCr(x = 0.1,0.5,0.8) composites were above 650 W/mK,higher than that of diamond/Cu composites.The tensile strengths ranged from 186 to 225 MPa,and the bonding strengths ranged from 400 to 525 MPa.Influences of Cr element on the thermo-physical properties and interface structures were analyzed.The intermediate layer was confirmed as Cr3C2 and the amount of Cr3C2 increased with the increase of Cr concentration in Cu-xCr alloys.When the Cr concentration was up to 0.5 wt.%,the content of the Cr3C2 layer was constant.As the thickness of the Cr3C2 layer became larger,the composites showed a lower thermal conductivity but higher mechanical properties.The coefficients of thermal expansion(CTE) of diamond/Cu-xCr(x = 0.1,0.5,0.8) composites were in good agreement with the predictions of the Kerner’ model.     

原位反应自发渗透法TiC／AZ91D镁基复合材料及AZ91D镁合金的拉伸变形与断裂行为

利用原位反应自发渗透技术合成了47．5％碳化钛TiC（体积分数，下同）增强AZ91D镁基复合材料，对比研究了该复合材料与铸态镁合金AZ91D基体的室温与高温拉伸变形行为，观察了拉伸断口微观组织形貌，并分析了这两种材料的断裂特征。结果表明，TiC／Mg复合材料具有良好的高温力学性能，在拉伸变形速率为0．001s^-1以及温度为723K，时其拉伸强度可达91．1MPa，而此时相同变形条件下的铸态AZ91D镁合金拉伸断裂强度只有41．1MPa，增幅达120％。而在室温下，镁基复合材料的拉伸断裂强度仅高出基体铸态镁合金23．4％。镁基复合材料的断裂应变较低，高低温时均表现为脆性断裂；而镁合金则由室温下的脆性断裂向高温下的韧性断裂过渡。     

Preparation a nickel-aluminide bonded diamond tool by self-propagating high-temperature synthesis and strengthening by nickel-chromium-phosphorus alloy and copper

Metal bonded diamond tools are normally manufactured by hot-press sintering, which is a high energy consuming process and using a large number of graphite moulds as well. Graphite dust is hazardous to operator's health and environment in machining of graphite mould. In present study, a metal bonded diamond tool is manufactured by self-propagating high-temperature synthesis (SHS) without hot press sintering and consuming of graphite moulds. In order to improve bonding of diamond grit and flexural strength of the tool for this method, nickel‑chromium‑phosphorus alloy and copper are introduced into nickel‑aluminum SHS in present study. The influence of nickel‑chromium‑phosphorus alloy and copper content on the combustion processes, the thermal behaviors, and the microstructures of the synthesized composite bonds are examined in detail. A diamond tool based on the optimized composite is prepared, and the grinding performance is examined. The results reveal that the addition of nickel‑chromium‑phosphorus alloy and copper inhibited the SHS reaction of nickel‑aluminum and reduced the combustion velocity, combustion temperature and reaction exothermic enthalpy. Copper can significantly improve flexural strength of the nickel aluminide bond. However, the maximum of nickel‑chromium‑phosphorus alloy or copper is about 60 wt% to sustain the SHS. A homogeneously dispersed and interconnected nickel-chromium-phosphorus phase in the matrix of nickel aluminides can be obtained with addition of over 40 wt% nickel‑chromium‑phosphorus alloy. A continuous chromium rich layer, composed of chromium carbide, has been formed at the interface between diamond grit and matrix, which renders a chemical bond of diamond grit. On the basis of the addition of 40 wt% nickel‑chromium‑phosphorus alloy and 10 wt% copper, an interconnected nickel‑chromium‑phosphorus phase for strong bonding of diamond grit and a flexural strength up to 700 MPa are achieved, which is considered as an excellent candidate material for diamond tools. The grinding test shows that the diamond tool owns a sound machining ability on the granite, and the diamond grit can be well retained and protruded.     

挤压熔体浸渗法制备金属涂覆碳纤维增强铝基复合材料的润湿性和力学性能改善

为了改善碳纤维与铝基体之间界面的润湿性和结合性能,采用挤压熔体浸渗法制备镍和铜涂覆碳纤维增强铝基复合材料,对两种不同涂层碳纤维增强铝基复合材料的界面润湿性、显微组织和力学性能进行比较和研究.显微组织结构分析表明,与无涂层碳纤维增强铝基复合材料相比,在相同的浸渗工艺条件下,在碳纤维表面涂覆两种金属均可以显著改善碳纤维与铝...     

气压熔渗法制备高导热金刚石/Cu–B合金复合材料

以硼质量分数为0.5%的Cu–B合金为金属基体以及平均粒径为500 μm的金刚石颗粒为增强体,采用气压熔渗法制备金刚石/Cu–B合金复合材料,研究气压参数对其组织结构和热物理性能的影响规律。结果表明:随着气压升高,金刚石与Cu–B合金之间的界面结合效果、导热性能均增强,热膨胀系数减小;当气压为10 MPa时,其界面结合效果最优,界面处生成的碳化物层将金刚石完全覆盖,且100 ℃时的样品热导率为680.3 W/(m·K),热膨胀系数为5.038×10?6 K?1,满足电子封装材料的热膨胀系数要求。      

Physical,Mechanical, and Tribological Attributes of Stir-Cast AZ91/SiCp Composite

In the present investigation, composites with silicon carbide particle （SiCp） as reinforcement and AZ91 magnesium alloy as matrix have been synthesized using liquid metal stir-casting technique with optimized processing conditions. The composites with good particle distribution in the matrix, and better grain refinement and good interfacial bonding between the matrix and reinforcement have been obtained. The effect of SiCp content on the physical, mechanical, and tribological properties of Mg-based metal matrix composite （MMC） is studied with respect to particle distribution, grain refinement, and particle/matrix interfacial reactions. The electrical conductivity, coefficient of thermal expansion, microas well as macro-hardness, tensile and compressive properties, and the fracture behavior of the composites along with dry sliding wear of the composites have been evaluated and compared with the base alloy.     

界面改性对SiCf/Cu基复合材料热膨胀性能的影响

研究了SiCf/Cu基复合材料分别在有无Ti6Al4V界面改性涂层两种情况下的纵向热膨胀行为,并采用扫描电镜对热循环后的试样进行显微形貌观察。结果表明,界面结合强度对纤维增强金属基复合材料的纵向热膨胀行为有很大影响。对于没有Ti6Al4V涂层的复合材料,其热膨胀行为不稳定,在经历连续两次热循环后,其纵向均表现为正的残余应变,原因是基体发生了严重的界面脱粘、滑移和膨胀;而对于有Ti6Al4V涂层的复合材料,其纵向热膨胀系数明显减小,两次热循环后其尺寸保持稳定,纤维/基体界面结合也保持稳定。     

Effect of Ti-6Al-4V particle reinforcements on mechanical properties of Mg-9Al-1Zn alloy

Mg-9Al-1Zn (AZ91) magnesium matrix composites reinforced by Ti-6Al-4V (TC4) particles were successfully prepared via powder metallurgical method. The yield strength (YS), ultimate tensile strength (UTS), and elongation (EL) showed a mountain-like tendency with the increase of the TC4 content. The mechanical properties of AZ91 magnesium matrix composites reached the optimal point with TC4 content of 10 wt.%, realizing YS, UTS, and EL of 335 MPa, 370 MPa, and 6.4%, respectively. The improvement of mechanical properties can be attributed to the effective load transfer from the magnesium matrix to the TC4 particles, dislocations associated with the difference in the coefficient of thermal expansion, good interfacial bonding between the Mg matrix and TC4 particles, and grain refinement strengthening.     

镀TiC金刚石/铝复合材料的界面及热膨胀性能

采用气压浸渗法制备高体积分数的镀TiC金刚石/铝复合材料,通过SEM和EDS等手段对复合材料的断口形貌进行分析,并研究TiC镀层对复合材料界面和热膨胀性能的影响。结果表明:TiC镀层改善金刚石颗粒与铝合金基体之间的选择性粘结现象,断裂方式以基体断裂为主。部分TiC会被氧化成TiO2并与铝合金基体反应生成Al2O3,从而实现金刚石颗粒与铝合金基体之间良好的界面结合;TiC镀层有效地降低复合材料的热膨胀系数(CTE),增强复合材料热膨胀性能的稳定性。在体积分数相同的情况下,CTE随金刚石颗粒尺寸的减小而减小。     

真空压力浸渗制备CF/Al复合材料热收缩与残余应力数值模拟与实验研究

针对连续碳纤维增强铝基复合材料(CF/Al复合材料),采用细观力学数值模拟与热性能试验结合的方法,研究了真空压力浸渗制备过程中的热收缩行为和热残余应力分布。结果表明,复合材料的横向热收缩应变量远大于轴向热收缩应变量,且具有横观各向同性,纤维随机分布的单胞有限元模型能够准确地预测复合材料轴向与横向热收缩行为曲线;复合材料制备完成后纤维和基体合金分别处于压应力和拉应力状态,基体和纤维的横向残余应力均小于其轴向残余应力,且均表现出横观各向同性;基体合金在轴向残余拉应力作用下会出现不同程度的损伤现象,特别是纤维间距较小部位过高的残余应力会引发界面的局部失效,从而不利于发挥复合材料承载性能,减少纤维局部偏聚是进一步改善提高复合材料力学性能的重要技术手段。     

镁基复合材料力学性能与微观组织研究

采用了液态浸渗法制备了Al2O3短纤维和SiC颗粒混杂增强镁合金复合材料。研究了浸渗压力对镁基复合材料力学性能和微观组织的影响。研究表明,当浸渗压力从0．4MPa增加到60MPa的过程中,由于组织的密实使得力学性能上升;随着浸渗压力的增加,将导致预制体受到压缩变形,纤维折断,从而导致综合力学性能下降。     

含微纳B4C/Ti颗粒铜基复合材料的微观组织与力学性能

采用高能球磨(HEBM)和放电等离子烧结(SPS)工艺成功制备出微纳B₄C/Ti颗粒增强铜基复合材料(CTBCs),通过X射线衍射(XRD)、光学显微镜(OM)、扫描电子显微镜(SEM)以及能谱(EDS)等测试手段对其微观组织形貌进行表征。结果表明,(B₄C+Ti)颗粒在基体中均匀分布,增强体与铜基体界面结合良好,且其结合形式为冶金结合和机械结合并存。采用阿基米德排水法测定出烧结态试样的致密度。复合材料的显微硬度、拉伸屈服强度、抗拉强度和延伸率等力学性能相较于纯铜试样得到显著提高,这主要归因于载荷传递、细化晶粒与热错配等强化机制。复合材料的拉伸断口表现出明显的韧性断裂特征。     

镀TiC金刚石/铝复合材料的热膨胀性能

采用气压浸渗法制备了金刚石体积分数为65%的铝基复合材料,分析了复合材料的显微组织并对热膨胀系数(CTE)进行了测试,研究了镀TiC金刚石/铝复合材料的热膨胀性能。结果表明,金刚石颗粒在铝合金基体中分布均匀,组织致密;TiC镀层有效地改善了金刚石颗粒与铝合金基体间选择性粘结现象,增强了金刚石与基体间的界面结合;镀TiC使复合材料热膨胀系数明显降低,Turner模型和Kerner模型的均值可以预测其热膨胀系数,而对于未镀层的复合材料则可以用Kerner模型进行预测。     

Study on fracture behavior of SiCp/A356 composites

The fracture behavior of SiCp/A356 composite at room and high temperatures was studied.Under tensile stress condition at room temperature, the fracture is mostly a combination of the brittle fracture of SiC particles and ductile fracture of A356 matrix.As the tensile temperature increases, the composite changes the main fracture behavior to the separation fracture of the bonding surface between SiC particles and A356 matrix.When the tensile temperature reaches 573 K, the fracture behavior of the composites is almost the whole separation fracture of the bonding surface, which is the main strengthening mechanism at high temperature.Under the cycle stress condition at room and high temperatures, the main fracture behavior of the composites is always a combination of the brittle fracture of SiC particles and ductile fracture of A356 matrix.However, under the cycle stress at high temperature, cycle behavior of the composites changes from cycle hardening at room temperature to the cycle softening at high temperature.     

金刚石/碳化硅/铝复合材料的热膨胀性能

采用气压浸渗法制备金刚石/碳化硅/铝复合材料,研究复合材料的断口形貌以及界面反应,测试复合材料的热膨胀性能。结果表明:金刚石表面Ti镀层使得其选择性粘附不同于未镀钛金刚石的,而在各个面上均粘附有Al,金刚石与基体间有着良好的界面结合,断裂方式以基体断裂为主,其界面反应后,Ti以Al3Ti和Ti-Al-Si等金属间化合物的形式析出,提高金刚石/铝界面的结合强度,降低复合材料的热膨胀系数;随着金刚石颗粒粒径的增大,金刚石和碳化硅颗粒间粒径比的增大增加了整个复合材料的体积分数,从而降低了其热膨胀系数;金刚石颗粒粒径增大导致热膨胀系数升高。这两方面共同影响复合材料的热膨胀系数,但前者起主导作用;金刚石和碳化硅在不同配比下的热膨胀系数随着复合材料中碳化硅含量的增加逐渐增大,Terner模型与Kerner模型的计算平均值能较好地预测实验结果。