Al2O3–ZrO2–SiO2 Ternary Glasses for Molybdenum Oxidation Barriers

The wettability of binary and ternary glasses belonging to SiO₂–Al₂O₃–ZrO₂ diagram has been studied using the sessile drop technique at 1750° and 1800°C. The ternary SiO₂–Al₂O₃–ZrO₂ (90–5–5 wt%) glass has proved to be well appropriated as a molybdenum oxidation barrier coating. The addition of 5 wt% of MoO₂ slightly improves its wettablity at higher temperatures without affecting its oxidation barrier properties. The Mo comes into the glass network as a mixture of Mo⁵⁺, Mo⁴⁺, and Mo⁶⁺. After oxidation at 1000°C in oxygen atmosphere, the molybdenum remains in the glass network as Mo⁶⁺.     

Calcium Hexaluminate and Its Stability Relations in the System CaO–Al2O3–SiO2

By a combination of solid-state sintering and quenching experiments the validity of calcium hexaluminate as a stable phase and the extent of its primary field in the system CaO–Al₂O₃–SiO₂ have been established. The size of the primary field is considerably reduced from that suggested by earlier work. The anorthite-corundum-calcium hexaluminate invariant point has been relocated at 28.0% CaO, 39.7% Al₂O₂, and 32.3% SiO₂ and at 1405°± 5°C.     

Homogeneous ZrO2–Al2O3 Composite Prepared by Nano-ZrO2 Particle Multilayer-Coated Al2O3 Particles

ZrO₂–Al₂O₃ nanocomposite particles were synthesized by coating nano-ZrO₂ particles on the surface of Al₂O₃ particles via the layer-by-layer (LBL) method. Polyacrylic acid (PAA) adsorption successfully modified the Al₂O₃ surface charge. Multilayer coating was successfully implemented, which was characterized by ξ potential, particle size. X-ray diffraction patterns showed that the content of ZrO₂ in the final powders could be well controlled by the LBL method. The powders coated with three layers of nano-ZrO₂ particles, which contained about 12 wt% ZrO₂, were compacted by dry press and cold isostatically pressed methods. After sintering the compact at 1450°C for 2 h under atmosphere, a sintered body with a low pore microstructure was obtained. Scanning electron microscopy micrographs of the sintered body indicated that ZrO₂ was well dispersed in the Al₂O₃ matrix.     

Influence of the Y2O3 Content and Temperature on the Mechanical Properties of Melt-Grown Al2O3–ZrO2 Eutectics

The effect of Y₂O₃ content on the flexure strength of melt-grown Al₂O₃–ZrO₂ eutectics was studied in a temperature range of 25°–1427°C. The processing conditions were carefully controlled to obtain a constant microstructure independent of Y₂O₃ content. The rod microstructure was made up of alternating bands of fine and coarse dispersions of irregular ZrO₂ platelets oriented along the growth axis and embedded in the continuous Al₂O₃ matrix. The highest flexure strength at ambient temperature was found in the material with 3 mol% Y₂O₃ in relation to ZrO₂(Y₂O₃). Higher Y₂O₃ content did not substantially modify the mechanical response; however, materials with 0.5 mol% presented a significant degradation in the flexure strength because of the presence of large defects. They were nucleated at the Al₂O₃–ZrO₂ interface during the martensitic transformation of ZrO₂ on cooling and propagated into the Al₂O₃ matrix driven by the tensile residual stresses generated by the transformation. The material with 3 mol% Y₂O₃ retained 80% of the flexure strength at 1427°C, whereas the mechanical properties of the eutectic with 0.5 mol% Y₂O₃ dropped rapidly with temperature as a result of extensive microcracking.     

Phase Equilibrium Relationships in a Portion of the System MgO–Al2O3–2CaO·SiO2

The system MgO–Al₂O₃–2CaO·SiO₂ comprises a plane through the tetrahedron CaO–MgO–Al₂O₃–SiO₂. A total of 108 compositions were prepared having an alumina content below the line joining 2CaO·Al₂O₃SiO₂ (gehlenite) and MgO·Al₂O₃ (spinel). Quenching experiments were carried out on 96 of these compositions at temperatures up to 1590°C. Three binary eutectic systems and two ternary eutectic systems are described. Compositions on this plane are of significance in an investigation of the constitution of basic refractory clinkers made from Canadian dolomitic magnesites. They also concern the compositions of certain blast furnace slags.     

Effect of Alkali Metal Oxide Addition on the Sinterability of MgO–B2O3–Al2O3 Glass–Al2O3 Filler Composites

The sintering of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler is terminated due to the crystallization of Al₄B₂O₉ in the glass. The densification of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler using pressureless sintering was accomplished by lowering the sintering temperature of the composite. The sintering temperature was lowered by the addition of small amounts of alkali metal oxides to the MgO–B₂O₃–Al₂O₃ glass system. The resultant composite has a four-point bending strength of 280 MPa, a coefficient of thermal expansion (RT—200°C) of 4.4 × 10⁻⁶ K⁻¹, a dielectric constant of 6.0 at 1 MHz, porosity of approximately 1%, and moisture resistance.     

Quaternary System Al2O3–CaO–MgO–SiO2: I, Study of the Crystallization Volume of Al2O3

Compatibility relations of Al₂O₃ in the quaternary system Al₂O₃–CaO–MgO–SiO₂ were studied by firing and quenching followed by microstructural and energy-dispersive X-ray examination. A projection of the liquidus surface of the primary phase volume of Al₂O₃ was constructed in terms of the CaO, SiO₂, and MgO contents of the mixtures recalculated to 100 wt%. Two invariant points, where four solids coexist with a liquid phase, were defined, and the positions of the isotherms were tentatively established. The effect of SiO₂, MgO, and CaO impurities on Al₂O₃ growth also was studied.     

Zirconium Aluminum Carbides: New Precursors for Synthesizing ZrO2–Al2O3 Composites

ZrO₂–Al₂O₃ nanocrystalline powders have been synthesized by oxidizing ternary Zr₂Al₃C₄ powders. The simultaneous oxidation of Al and Zr in Zr₂Al₃C₄ results in homogeneous mixture of ZrO₂ and Al₂O₃ at nanoscale. Bulk nano- and submicro-composites were prepared by hot-pressing as-oxidized powders at 1100°–1500°C. The composition and microstructure evolution during sintering was investigated by XRD, Raman spectroscopy, SEM, and TEM. The crystallite size of ZrO₂ in the composites increased from 7.5 nm for as-oxidized powders to about 0.5 μm at 1500°C, while the tetragonal polymorph gradually converted to monolithic one with increasing crystallite size. The Al₂O₃ in the composites transformed from an amorphous phase in as oxidized powders to θ phase at 1100°C and α phase at higher temperatures. The hardness of the composite increased from 2.0 GPa at 1100°C to 13.5 GPa at 1400°C due to the increase of density.     

Determination of CaO–SiO2–MgO–Al2O3–CrOx Liquidus

In this work, the liquidus of synthetic CaO–SiO₂–MgO–Al₂O₃–CrO _x slags is evaluated in the industrially relevant compositional domain. Equilibrium experiments are carried out at 1500°C and partial oxygen pressure ( p _O2) 10^−11.04 atm, and at 1600°C and p _O2=10^−10.16 and 10^−9.36 atm. The studied basicities (CaO/SiO₂) are 1.2 and 0.5. Al₂O₃ levels range from 0 to 30 wt%. Oversaturated liquid is sampled and phase relations are measured with quantitative electron probe microanalysis–wavelength dispersive spectroscopy (EPMA–WDS). The results are compared with the commercially available FactSage thermodynamic databases. Qualitative agreement is always obtained. Also a good quantitative agreement is found at the higher basicity, especially for the spinel liquidus. A minor but systematic deviation can be observed for the eskolaite liquidus. At the lower basicity, the calculated phase diagram deviates strongly from the experimental results, probably due to missing ternary interactions in the database.     

Oxidation State of Chromium in CaO–Al2O3–CrOx–SiO2 Melts under Strongly Reducing Conditions at 1500°C

Equilibrium ratios Cr²⁺/Cr³⁺ of chromium oxide dissolved in CaO–chromium oxide–Al₂O₃–SiO₂ melts have been determined by analysis of samples equilibrated at 1500°C under strongly reducing conditions ( p _o2= 10^−9.56 to 10^−12.50 atm). The majority of the chromium is divalent (Cr²⁺) under these conditions and Cr²⁺/Cr³⁺ ratios at given constant oxygen pressures decrease with increasing basicity of the melts, expressed as CaO/SiO₂ ratios. In addition, Cr²⁺/Cr³⁺ ratios, at a given CaO/SiO₂ ratio, are relatively unaffected by the amount of Al₂O₃ present.     

Formation and Transformation of Cubic ZrO2 Solid Solutions in the System ZrO2—Al2O3

In the system ZrO₂-Al₂O₃, cubic ZrO₂ solid solutions containing up to 40 mol% Al₂O₃ crystallize at low temperatures from amorphous materials prepared by the simultaneous hydrolysis of zirconium and aluminum alkoxides. The values of the lattice parameter, a, increase linearly from 0.5095 to 0.5129 nm with increasing Al₂O₃ content. At higher temperatures, the solid solutions transform into tetragonal ZrO₂ and α-Al₂O₃. Pure ZrO₂ crystallizes in the tetragonal form at 415° to 440°C.     

Homogeneous Fabrication of Al2O3–ZrO2–SiC Whisker Composite by Surface-Induced Coating

Al₂O₃–ZrO₂–SiC whisker composites were prepared by surface-induced coating of the precursor for the ZrO₂ phase on the kinetically stable colloid particles of Al₂O₃ and SiC whisker. The fabricated composites were characterized by a uniform spatial distribution of ZrO₂ and SiC whisker phases throughout the Al₂O₃ matrix. The fracture toughness values of the Al₂O₃–15 vol% ZrO₂–20 vol% SiC whisker composites (∼12 MPa.m^1/2) are substantially greater than those of comparable Al₂O₃–SiC whisker composites, indicating that both the toughening resulting from the process zone mechanism and that caused by the reinforced SiC whiskers work simultaneously in hot-pressed composites.     

Quaternary System Al2O3–CaO–MgO–SiO2: II Study of the Crystallization Volume of MgAl2O4

Solid-state compatibility and melting relations of MgAl₂O₄ in the quaternary system Al₂O₃–CaO–MgO–SiO₂ were studied by firing and quenching selected samples located in the 65 wt% MgAl₂O₄, plane followed by microstructural and energy dispersive X-ray analysis. A projection of the liquidus surface of the primary crystallization volume of MgAl₂O₄ was constructed from CaO, SiO₂ and exceeding Al₂O₃, not involved in stoichiometric MgAl₂O₄ formation; those three amounts were recalculated to 100 wt%. The temperature and character of six invariant points, where four solids co-exist with a liquid phase, were defined. One maximum point was localized and the positions of the isotherms were tentatively established. The effect of CaO, SiO₂, and Al₂O₃ impurities on the high temperature behavior of spinel materials was also discussed.     

Synthesis, Densification, and Phase Evolution Studies of Al2O3–Al2TiO5–TiO2 Nanocomposites and Measurement of Their Electrical Properties

Alumina–aluminum titanate–titania (Al₂O₃–Al₂TiO₅–TiO₂) nanocomposites were synthesized using alkoxide precursor solutions. Thermal analysis provided information on phase evolution from the as-synthesized gel with an increase in temperature. Calcination at 700°C led to the formation of an Al₂O₃–TiO₂ nanocomposite, while at a higher temperature (1300°C) an Al₂O₃–Al₂TiO₅–TiO₂ nanocomposite was formed. The nanocomposites were uniaxially compacted and sintered in a pressureless environment in air to study the densification behavior, grain growth, and phase evolution. The effects of nanosize particles on the crystal structure and densification of the nanocomposite have been discussed. The sintered nanocomposite structures were also characterized for dielectric properties.     

Phase Equilibrium Relationships at Liquidus Temperatures in the System FeO–Fe2O3–Al2O3–SiO2

Phase equilibrium data at liquidus temperatures are presented for mixtures in the system FeO–Fe₂O₃–Al₂O₃–SiO₂. The volume located between the 1 and 0.2 atm. O₂ isobaric surfaces of the tetrahedron representing this system was studied in detail. Scattered data were obtained at lower O₂ pressures. Results obtained in the present investigation were combined with data in the literature to construct a phase equilibrium diagram, at liquidus temperatures, for the entire system FeO–Fe₂O₃–Al 2 O₃–SiO₂. Methods for interpretation of the diagram are explained.     

Influence of the Characteristics of Spinels on the Slag Resistance of Al2O3–MgO and Al2O3–Spinel Castables

The XRD patterns at ambient temperature and at 1500°C showed that the spinel in the Al₂O₃–MgO castables fired at 1500°C for 3 h has the higher peak intensity, compared to those in Al₂O₃–spinel castables; the interplanar distance in the set (311) is 2.43 Å for the spinel in Al₂O₃–MgO castables as well as the spinels in Al₂O₃–spinel castables using spinels containing 73, 90, and 94 wt% Al₂O₃, respectively. The corresponding alumina contents of the spinels in these castables were estimated to be around 75 wt%. The smaller grain size of the spinel in Al₂O₃–MgO castables compared to that in Al₂O₃–spinel castables is evidenced by the recrystallization of the in situ spinel only occurring in Al₂O₃–MgO castables as revealed by the XRD patterns at ambient temperature and at 1500°C. The larger amount and smaller grain size of the in situ spinel in the matrix mostly account for the better slag resistance of Al₂O₃–MgO castables, compared to Al₂O₃–spinel castables.     

SiO2–PbO–CaO–ZrO2–TiO2–(B2O3–K2O), A New Zirconolite Glass–Ceramic System: Crystallization Behavior and Microstructure Evaluation

Zirconolite (CaZrTi₂O₇) is a mineral that has a high containment capacity for actinides and lanthanides and is considered to be a good candidate for the immobilization of radioactive wastes. The glass–ceramic technique seems to be a very suitable and convenient method to produce zirconolite crystals by precipitating them in a specific glass matrix. In this study, development of a new zirconolite-based glass–ceramic belonging to SiO₂–PbO–CaO–ZrO₂–TiO₂–(B₂O₃–K₂O) system was investigated. The presence of PbO, together with B₂O₃ and K₂O, allowed the preparation of a X-ray diffraction (XRD) amorphous glass with a relatively high concentration of ZrO₂ and TiO₂, which was successfully converted to a glass–ceramic containing 34 wt% of zirconolite after heating at 770°C for 4 h. Differential thermal analysis, XRD, scanning electron microscope, and energy dispersive X-ray spectroscopy were used to determine the crystallization conditions, identify the crystallized phases, determine their compositions and quantities and observe and analyze the microstructures. The zirconolite crystals showed a platelet morphology with a monoclinic structure characterized by a =1.246 nm, b =0.7193 nm, c =1.128 nm, and β=100.508°.     

Properties of Sm2O3─Al2O3─SiO2 Glasses for In Vivo Applications

The compositional range for glass formation below 1600°C in the Sm₂O₃─Al₂O₃─SiO₂ system is (9–25)Sm₂O₃─(10–35)Al₂O₃─(40–75)SiO₂ (mol%). Selected properties of the Sm₂O₃─Al₂O₃─SiO₂ (SmAS) glasses were evaluated as a function of composition. The density, refractive index, microhardness, and thermal expansion coefficient increased as the Sm₂O₃ content increased from 9 to 25 mol%, the values exceeding those for fused silica. The dissolution rate in 1 N HCl and in deionized water increased with increasing Sm₂O₃ content and with increasing temperature to 70°C. The transformation temperature ( T _g ) and dilatometric softening temperature ( T _d ) of the SmAS glasses exceeded 800° and 850°C, respectively.     

Glass Formation and Recrystallization in the Lithium Metasilicate Region of the System Li2O–Al2O3–SiO2

The stability of the vitreous state in the lithium metasilicate region of the system Li₂O–Al₂O₃–SiO₂ was found to be a function of the concentration of lithia. The higher the lithia content, the less stable was the glass. The devitrification of glasses in this system was studied. In addition to the phases present at or near the liquidus, it was found that the β -eucryptite– β -quartz solid solution phase was metastable over most of the region. The Li₂O–SiO₂, β -Li₂O–Al₂O₃–4SiO₂ solid solution, β -Li₂O–Al₂O₃–2SiO₂ solid solution triple point was estimated to be near 62.5% SiO₂, 17% Al₂O₃, and 20.5% Li₂O (by weight). The thermal expansions of bodies in this region were measured and the values obtained are explained in terms of the phases present.