低熔钛体瓷研制及其性能研究

采用硼硅酸盐玻璃体系制备低熔钛专用体瓷,研究了体瓷组成与热膨胀系数的关系,并采用XRD和细胞毒性实验分别研究了钛体瓷的晶相组成和生物相容性。结果表明:钛体瓷为不含晶体的均质玻璃体,其热膨胀系数随SiO2含量的增加而减小;所研制的钛体瓷细胞毒性为0级,生物相容性良好,可望进一步应用于临床修复。     

低熔纯钛用体瓷的研制及其性能研究

采用硼硅酸盐玻璃体系制备低熔钛专用体瓷,研究了体瓷组成与热膨胀系数的关系,并采用XRD和细胞毒性实验分别研究了钛体瓷的晶相组成和生物相容性。结果表明,钛体瓷为不含晶体的均质玻璃体,其热膨胀系数随SiO2含量的增加而减小;通过对比两种配方的烧结温度与力学性能,最终确定体瓷配方和烧结工艺:自制钛体瓷的烧结温度为760℃,抗弯强度、断裂韧性和维氏硬度分别为(85±4.07)MPa、(1.44±0.04)MPa/m1/2和(3904±21.71)MPa/mm2,硬度稍高于天然牙釉质。XRD结果表明自制钛体瓷为不含晶体的均质玻璃体;细胞毒性为0级,对细胞无抑制作用,可望进一步应用于临床修复。     

低温烧结法制备LZS系微晶玻璃及其性能

采用烧结法制备出LZS系微晶玻璃.使用DTA分析了玻璃的析晶过程,运用XRD、SEM等对晶相和晶粒大小进行了观察和分析,讨论了温度对烧结程度、主晶相、晶体微观形貌及热膨胀系数的影响.结果表明:当晶化温度低于725℃时,主晶相为硅酸锂锌,次晶相为Li2ZnSiO4并有少量石英;温度高于725℃时,主晶相转变为石英,次晶相为硅酸锂锌和Li2ZnSiO4,为长度在1.5μm左右的棒状晶体.在700～725℃之间烧结接近完成.最佳烧结温度为725℃.微晶玻璃热膨胀系数与烧结程度、晶相含量和主晶相的热膨胀系数有关.     

CaO掺杂对镁铝硅系微晶玻璃结构与性能的影响

采用高温熔融法制备镁铝硅系微晶玻璃,研究了CaO掺杂对晶相组成、微观形貌以及抗弯强度、热膨胀系数、介电性能的影响,并基于Arrhenius恒定升温速率模型计算出烧结活化能。结果表明,由于Ca原子进入玻璃网络中,CaO加入有效降低玻璃的软化点及析晶温度,改变玻璃的析晶倾向,同时显著降低烧结活化能,并促进微晶玻璃的烧结过程。次晶相(MgAl_2Si_3O_(18))_(0.6)的增加导致微晶玻璃的热膨胀系数提高,而抗弯强度的提升与体积密度的增大及高热膨胀相产生的内应力有关。当CaO掺杂量为3%(质量分数)时,在950℃烧结获得最佳性能:抗弯强度为152 MPa、热膨胀系数为3.52×10~(-6)/℃、介电常数为5.89、介电损耗为1.85×10~(-3)。     

烧结温度对提钛渣微晶玻璃析晶及显微结构的影响

以攀枝花提钛渣为原料,通过直接烧结法制备了以钙镁黄长石、透辉石及钙钛矿为晶相的多相微晶玻璃。采用多种分析手段,研究了烧结温度(1170～1190℃)对微晶玻璃的析晶、显微结构及性能的影响。结果表明:随着烧结温度的升高,钙镁黄长石含量先减少后增加,透辉石含量先不变后减少;微晶玻璃中晶粒聚集程度增加,晶界延长,液相填充晶粒间的空隙并与晶粒相互咬合,显微结构致密;烧结温度能够影响微晶玻璃中液相的分布与含量;1185℃时微晶玻璃的线收缩率和体积密度达到最大,分别是14.41%和2.50g/cm~3,吸水率为1.45%;过高的烧结温度(1190℃)会降低致密程度。     

氟硅酸盐微晶玻璃的热膨胀性能研究

氟硅酸盐微晶玻璃的热膨胀性能主要取决于微晶玻璃的晶相组成及其相对含量．透辉石结晶相的含量增加使微晶玻璃的热膨胀系数降低,与此相反碱镁闪石结晶相的含量增加却使微晶玻璃的膨胀系数增加．K2O－MgO－SiO2－CaF2系统氟硅酸盐微晶玻璃的最小热膨胀系数为：78．4×10－7（20～300℃）;最大热膨胀系数为：85．6×107（20～300℃）．     

β-锂霞石负膨胀微晶玻璃的制备技术及结构特征

研究了β锂霞石微晶玻璃的制备技术、结构特征及其负膨胀特征。首先采用玻璃结晶法制备β锂霞石负膨胀微晶玻璃材料,然后通过XRD、SEM等测试手段,表征了β锂霞石微晶玻璃材料的结构特征。并讨论β锂霞石负膨胀微晶玻璃的膨胀系数及其与晶相组成和晶化温度及时间的依从关系,使其负膨胀系数在一定范围内连续可调。研究并制备出热膨胀系数可达到为-1.037×10-5/℃的β锂霞石微晶玻璃。     

透明LAS微晶玻璃的显微结构和热性能研究

用熔融法制备LAS透明微晶玻璃;采用DSC,XRD,SEM等测试方法,研究了透明LAS微晶玻璃的晶相组成、显微结构及热性能。结果表明:720℃核化2 h,780~900℃晶化2 h均得到β-石英固溶体微晶玻璃,晶粒尺寸在10~30 nm之间,具有优良的透明性,30~700℃的热膨胀系数在(3.50~5.92)×10-7/℃之间变化;720℃核化2 h,860℃晶化2 h得到的微晶玻璃在900℃保温10 h后透明性优良,30~700℃的热膨胀系数为3.64×10-7/℃。     

锂铝硅微晶玻璃结构与性能热稳定性研究

以TiO₂、ZrO₂为形核剂制备了透明低膨胀锂铝硅系微晶玻璃, 通过测定其等温转变动力学曲线,讨论锂铝硅玻璃析晶及相变与热处理温度和时间的关系, 并采用DTA、XRD和SEM等方法研究锂铝硅微晶玻璃结构和性能的热稳定性. 结果表明, 以β-石英固溶体为主晶相的透明微晶玻璃能在750~900℃较宽的温度范围和较长的时间内保持主晶相和结构的稳定, 850℃保温5h仍具有较高的透光率和极低的热膨胀系数, 性能具有很好的高温稳定性. 材料结构和性能的稳定性均源自钛锆复合形核剂较高的形核效率.     

氧化铋对微晶玻璃的相转变和性能的影响

为研究Bi2O3在堇青石基微晶玻璃烧结中的作用及其添加量对微晶玻璃的相转变和性能的影响,采用烧结法制备了不同Bi2O3含量的微晶玻璃,并对其进行了X射线衍射分析、显微分析和性能测试.结果表明:Bi2O3的加入降低了堇青石的u相向a相转变的温度,并有效促进微晶玻璃的烧结致密化;烧结样品的介电常数和抗折强度均随着Bi2O3加入量的增加而增加,且与密度变化规律相似;当Bi2O3添加量(质量分数)达5%时样品的介质损耗因子最低(＜10-3);微晶玻璃烧结样品的热膨胀系数基本符合线性规律.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...