Ru掺杂TiO2和TiO2/SiO2光催化剂的制备及可见光分解水制氢性能研究

采用溶胶-凝胶法制备了系列Ru/TiO2和Ru/TiO2/SiO2可见光活性光催化剂。通过TEM、XPS、XRD、UV-Vis漫反射和电化学对样品进行了表征。发现Ru和Si的存在可以抑制TiO2的相转变和晶粒生长;Ru掺杂使TiO2和TiO2/SiO2对可见光的吸收增强,也提高了光生电子和空穴的分离,因而,提高了催化剂可见光分解水制氢活性。当Ru在TiO2和TiO2/SiO2中的掺杂量分别为0.014%和0.021%(质量分数)时,光催化剂的可见光活性最高,且Ru/TiO2/SiO2活性为Ru/TiO2的5倍。     

热还原法制备氧化石墨烯/TiO_2复合材料及其光催化性能研究

采用Hummers法制得氧化石墨烯,以钛酸丁酯为钛源,采用原位溶胶-凝胶技术制备了氧化石墨烯/TiO2复合材料,进一步经过加热还原的方法,制备热还原氧化石墨烯/TiO2复合光催化剂,通过FT-IR、XRD、Raman、SEM、TEM和UV-Vis光谱等对产物进行了表征,并测试了该复合光催化剂在可见光下对甲基橙的光催化降解性能。结果表明,制备的复合光催化剂主晶相为锐钛矿型TiO2,热还原氧化石墨烯表面富集的颗粒尺寸15nm左右,颗粒分布均匀。热还原氧化石墨烯/TiO2复合光催化剂在可见光下具有优异的光催化性能。     

S、RE共掺杂TiO2的制备及其可见光分解水制氢性能

采用溶胶-凝胶法制备了系列稀土(La、Eu、Nd、Tb、Er)和硫共掺杂TiO2光催化剂RE/S/TiO2。通过紫外-可见(UV-Vis)漫反射、X射线衍射(XRD)对催化剂进行了表征。以EDTA为电子给体,考察了光催化剂在可见光照射下的制氢活性。研究结果表明,S/TiO2具有可见光活性,稀土掺杂进一步提高了S/TiO2可见光活性,其活性顺序依次为Eu/S/TiO2>La/S/TiO2>Nd/S/TiO2>Tb/S/TiO2>Er/S/TiO2。与纯TiO2和S/TiO2光催化剂相比,稀土掺杂使催化剂的粒径减小,晶格畸变应力增大,从而提高了催化剂可见光制氢活性。     

Rose bengal-Cu-TiO2的制备及可见光制氢活性研究

用光还原方法制备了负载Cu的光催化剂Cu-TiO2,用染料Rose bengal敏化Cu-TiO2制备了具有可见光活性的Rose bengal-Cu-TiO2光催化剂,通过可见光(λ≥420nm)下分解水制氢考察了催化剂的活性,利用XRD、UV-vis吸收光谱对样品进行了表征.结果表明:载Cu增强了TiO2对可见光的吸收,Cu负载量对催化剂活性有一定的影响,Cu的最佳负载量为5%(质量分数).Cu的负载也增加了TiO2对染料的吸附,从而提高了TiO2对可见光的吸收和光催化活性.     

TNTs/石墨烯复合材料的合成及光电催化分解性能研究

采用水热法以TiO2和石墨烯为原料制备了石墨烯杂化的钛酸纳米管复合光催化材料。首次将石墨烯修饰的钛酸纳米管涂布在电极上,研究了其在可见光照射下电化学方法降解罗丹明-B的性能。结果表明,制备的该系列复合光催化剂都具有良好的可见光响应和杰出的电化学降解罗丹明-B表现。其中,石墨烯含量为5%的样品具有最优的活性。另外通过实验发现,较低的水热反应温度制备的光催化剂的催化性能更佳。     

Rose Bengal-Cu-TiO2的制备及可见光制氢活性研究

用光还原方法制备了负载Cu的光催化剂Cu-TiO2，并通过染料Rose bengal敏化，制备了具有可见光活性的Rose bengal-Cu-TiO2光催化剂，通过可见光下光解水制氢考察了催化剂的活性，并利用XRD、UV-Vis等手段对样品进行了表征。实验表明：载Cu增强了TiO2对可见光的吸收，Cu负载量对催化剂活性有一定的影响，Cu的最佳负载量为5％（质量分数）。Cu的负载也增加了TiO2对染料的吸附强度和吸附量，从而提高了TiO2对可见光的吸收和光催化活性。但载Cu的TiO2催化剂的活性和传统的载贵金属Pt的TiO2催化剂相比，其光催化活性较低，有待进一步提高．     

S掺杂TiO_2/石墨烯复合催化剂制备及光催化分解水制氢

为了提高TiO2光解水制氢的光催化性能,通过水热合成法一步制备了S掺杂TiO2/石墨烯(RGO)复合催化剂。采用XRD、XPS、FT-IR、TEM、UV-Vis等测试方法对其进行了表征,并研究了复合催化剂光催化分解水制氢性能。结果表明,在S-TiO2/RGO复合催化剂中,TiO2以14nm左右的纳米颗粒分散在石墨烯片层上;与同等条件下制备的TiO2相比,复合催化剂在可见光区的吸收明显增强;当m(S)∶m(RGO)∶m(TiO2)为1∶0.1∶25时,所制备的复合催化剂在同等条件下产氢速率最大,为141.7μmol/h。     

Bi2O2CO3/TiO2复合粉体的制备及其光催化性能研究

采用水热法制备了Bi2O2CO3,并将其与TiO2进行了复合。XRD数据表明此复合光催化剂中Bi2O2CO3结晶性良好,紫外-可见漫反射光谱说明Bi2O2CO3的加入使其吸收带边有一定的红移。研究了紫外-可见光照射下Bi2O2CO3/TiO2复合光催化剂对亚甲基蓝溶液的降解性能,结果表明当Bi2O2CO3与TiO2的质量比为0.032时,得到性能最优的复合光催化剂,其光催化活性优于TiO2。     

3D Bi2WO6/TiO2异质结型光催化剂的制备以及增强的可见光催化性能

通过浸渍法合成了3D多组分Bi2WO6/TiO2异质结型复合光催化剂,多次浸渍使TiO2粒子层层沉积到花状Bi2WO6结构的表面。采用X射线粉末衍射(XRD)、扫描电镜(SEM)、光致发光光谱(PL)以及紫外-可见漫反射(UV-Vis)吸收光谱分别对所制备的复合光催化剂进行了表征,并以500W氙灯为光源,罗丹明B(RhB)为降解对象,进行了光催化活性测试,考察了不同TiO2复合量对Bi2WO6光催化剂反应活性的影响。结果表明,异质结型Bi2WO6/TiO2复合光催化剂的光催化活性明显优于纯Bi2WO6和TiO2。当复合15%(质量分数)TiO2时,所制备的复合光催化剂最有效促进电子和空穴的分离,并且光催化活性得到提高。活性提高的原因是所形成的异质结特殊的界面能够显著地降低光生电子和空穴的复合几率,并且具有较高的光吸收能力。     

镧掺杂TiO2/膨润土复合光催化材料的制备及性能

以钠基膨润土为载体,钛酸丁酯和硝酸镧为原料,采用溶胶-凝胶法制备镧掺杂TiO2/膨润土复合光催化剂,采用X射线衍射(XRD)和红外光谱(IR)对复合催化剂进行了表征,在紫外光照射下,通过对TNT废水的光催化降解,考察其光催化活性。实验结果表明,掺杂镧与未掺杂镧的TiO2/膨润土复合光催化剂中TiO2主要以锐钛矿型存在;掺杂镧的TiO2/膨润土复合光催化剂的光催化性能明显优于未掺杂镧的TiO2/膨润土复合光催化剂,当镧的掺杂量为1%(原子分数),焙烧温度为500℃时,其光催化活性达到最佳效果。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...