Influences of compatibilizers on rheology and mechanical properties of propylene random copolymer/styrene‐ethylene‐butylene‐styrene block copolymer/organic‐montmorillonite nanocomposites

Propylene random copolymer (PPR)/styrene‐ethylene‐butylene‐styrene block copolymer (SEBS)/compatibilizer/organic‐montmorillonite (OMMT) quaternary nanocomposites and PPR/compatibilizer/OMMT ternary nanocomposites were prepared via two‐stage melt blending and influences of compatibilizers, maleic anhydride (MA) grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), poly(octene‐co‐ethylene) (POE‐g‐MA), or propylene block copolymers (PPB‐g‐MA), on rheology and mechanical properties of the nanocomposites were investigated. The results of X‐ray diffraction measurement and transmission electron microscopy observation showed that OMMT layers were mainly intercalated in the nanocomposites except for the mainly exfoliated structure in the quaternary nanocomposites using POE‐g‐MA as compatibilizer. The nanocomposites exhibited pseudo‐solid like viscoelasticity in low frequencies and shear‐thinning in high shear rates. As far as OMMT dispersion was concerned, POE‐g‐MA was superior to SEBS‐g‐MA and PPB‐g‐MA, which gives rise to the highest viscosities in both the ternary and quaternary nanocomposites. The quaternary nanocomposites containing POE‐g‐MA were endowed with balanced toughness and rigidity. It was suggested that a suitable combination of compatibilizer and SEBS was an essentially important factor for adjusting the OMMT dispersion and distribution, the rheological and mechanical performances of the nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical and thermal properties of toughened PA6/HDPE/SEBS‐g‐MA/Clay nanocomposite

Preparation and morphology of Polyamide 6 (PA6)/high density polyethylene (HDPE)/Styrene/Ethylene–Butylene/Styrene grafted with maleic anhydride (SEBS‐g‐MA)/Modified clay nanocomposites were studied. Mixing was performed using melting process in an extruder co‐rotating twin screw. After etching the materials with boiling toluene and THF at room temperature, the morphology of sample checked by scanning electron microscopy (SEM) analyses. X‐ray diffraction (XRD) used for evaluation of the effects of organo‐clay addition in the structure of nanocomposites. XRD traces showed that the characteristic (001) peak of the nanocomposites shifted to the lower degree region. XRD and SEM results showed more uniformly distribution and dispersion of HDPE in the PA6 matrix. Better sample morphology obtained, regarding less distance, and more uniformity between nanoparticles. The mechanical properties like tensile strength, impact strength, hardness and thermal properties of these toughened nanocomposites are discussed in terms of the nanoclay, SEBS‐g‐MA contents and morphology. Adding nanoclay improved hardness of nanocomposites product but reduced toughness and thermal properties. Meanwhile the presence of SEBS‐g‐MA as a compatibilizer improved toughness, thermal properties, hardness property, and the balance properties are achieved. POLYM. ENG. SCI., 55:29–33, 2015. © 2014 Society of Plastics Engineers     

Influence of thermoplastic elastomers on adhesion in polyethylene–wood flour composites

The mechanical properties of recycled low-density polyethylene/wood flour (LDPE/WF) composites are improved when a maleated triblock copolymer styrene–ethylene/butylene–styrene (SEBS–MA) is added as a compatibilizer. The composites' tensile strength reached a maximum level with 4 wt % SEBS–MA content. The compatibilizer had a positive effect on the impact strength and elongation at break but decreased the composites' stiffness. Dynamic mechanical thermal analysis (DMTA), a lap shear adhesion test, and a scanning electron microscope (SEM) were used to investigate the nature of the interfacial adhesion between the WF/SEBS and between the WF/SEBS–MA. Tan δ peak temperatures for the various combinations showed interaction between the ethylene/butylene (EB) part of the copolymer and the wood flour in the maleated system. The shear lap test showed that adhesion between the wood and SEBS–MA is better than between the wood and SEBS. The electron microscopy study of the fracture surfaces confirmed good adhesion between the wood particles and the LDPE/SEBS–MA matrix. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1845–1855, 1998     

Interfacially compatibilized LDPE/POE blends reinforced with nanoclay: investigation of morphology,rheology and dynamic mechanical properties

Morphological, melt rheological and dynamic mechanical properties of low-density polyethylene (LDPE)/ethylene–octene copolymer (POE)/organo-montmorillonite (OMMT) nanocomposites, prepared via melt compounding were studied. The XRD traces indicated different levels of intercalated structures for the nanocomposites. Addition of a compatibilizer (PE-g-MA) improved the intercalation process. TEM results revealed existence of clay layers in both phases but they were mainly localized in the elastomeric POE phase. Addition of 5 wt% OMMT to the LDPE/POE blend led to reduction in the size of the elastomer particles confirmed by AFM. The complex viscosity and storage modulus showed little effect of the presence of the clay when no compatibilizer was added. As the extent of exfoliation increased with addition of compatibilizer, the linear viscoelastic behavior of the composites gradually changed specially at low-frequency regions. The interfacially compatibilized nanocomposites with 5 wt% OMMT had the highest melt viscosity and modulus among all the studied nanocomposites and blends. Also, this particular composition showed the best improvement in dynamic storage modulus. The results indicated that clay dispersion and interfacial adhesion, and consequently different properties of LDPE/POE/clay nanocomposites, are greatly affected by addition of compatibilizer.     

Preparation and properties of styrene–ethylene–butylene–styrene block copolymer/clay nanocomposites: I. Effect of clay content and compatibilizer types

BACKGROUND: Polymer/clay (silicate) systems exhibit great promise for industrial applications due to their ability to display synergistically advanced properties with relatively small amounts of clay loads. The effects of various compatibilizers on styrene–ethylene–butylene–styrene block copolymer (SEBS)/clay nanocomposites with various amounts of clay using a melt mixing process are investigated. RESULTS: SEBS/clay nanocomposites were prepared via melt mixing. Two types of maleated compatibilizers, styrene–ethylene–butylene–styrene block copolymer grafted maleic anhydride (SEBS‐g‐MA) and polypropylene grafted maleic anhydride (PP‐g‐MA), were incorporated to improve the dispersion of various amounts of commercial organoclay (denoted as 20A). Experimental samples were analyzed using X‐ray diffraction and transmission electron microscopy. Thermal stability was enhanced through the addition of clay with or without compatibilizers. The dynamic mechanical properties and rheological properties indicated enhanced interaction for the compatibilized nanocomposites. In particular, the PP‐g‐MA compatibilized system conferred higher tensile strength or Young's modulus than the SEBS‐g‐MA compatibilized system, although SEBS‐g‐MA seemed to further expand the interlayer spacing of the clay compared with PP‐g‐MA. CONCLUSION: These unusual results suggest that the matrix properties and compatibilizer types are crucial factors in attaining the best mechanical property performance at a specific clay content. Copyright © 2007 Society of Chemical Industry     

Property enhancement in polypropylene ternary blend nanocomposites via a novel poly(ethylene oxide)‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene toughener–compatibilizer system

Synthesis and characterization of a novel toughener–compatibilizer for polypropylene (PP)–montmorillonite (MMT) nanocomposites were conducted to provide enhanced mechanical and thermal properties. Poly(ethylene oxide) (PEO) blocks were synthetically grafted onto maleic anhydride‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene (SEBS‐g‐MA). Special attention was paid to emphasize the effect of PEO‐grafted SEBS (SEBS‐g‐PEO) against SEBS‐g‐MA on morphology, static/dynamic mechanical properties and surface hydrophilicity of the resultant blends and nanocomposites. It was found that the silicate layers of neat MMT are well separated by PEO chains chemically bonded to nonpolar SEBS polymer without needing any organophilic modification of the clay as confirmed by X‐ray diffraction and transmission electron microscopy analyses. From scanning electron microscopy analyses, elastomeric domains interacting with MMT layers via PEO sites were found to be distributed in the PP matrix with higher number and smaller sizes than the corresponding blend. As a benefit of PEO grafting, SEBS‐g‐PEO‐containing nanocomposite exhibited not only higher toughness/impact strength but also increased creep recovery, as compared to corresponding SEBS‐g‐MA‐containing nanocomposite and neat PP. The damping parameter of the same nanocomposite was also found to be high in a broad range of temperatures as another advantage of the SEBS‐g‐PEO toughener–compatibilizer. The water contact angles of the blends and nanocomposites were found to be lower than that of neat hydrophobic PP which is desirable for finishing processes such as dyeing and coating. © 2018 Society of Chemical Industry     

The effect of SEBS on interfacial tension and rheological properties of LDPE/PS blend

The effects of SEBS as a compatibilizer on the interfacial tension and rheological properties of LDPE/PS blend have been studied. Interfacial tension was measured by the breaking thread method. The measured interfacial tension of the LDPE/PS blend was 8.26 dyn/cm. It decreased rapidly with SEBS contents to 1 wt % and then leveled off to a saturation value, 3.6 dyn/cm. Dynamic oscillatory shear, elongational viscosity, and recovery after elongation were measured as the rheological properties. Storage modulus at low frequencies decreased with SEBS contents to 1 wt %. More addition of SEBS, however, increased the storage modulus at low frequencies. Similar behaviors could be observed in elongation viscosity and recovery after elongation. Hardening of elongational viscosity and recovery after elongation were reduced with 1 wt % SEBS, and they enhanced again with more SEBS contents. This means that there is a critical concentration of SEBS that acts as a compatibilizer and reduces the interfacial tension. More SEBS than the critical concentration saturates the interface and increases the elasticity of the LDPE/PS blend, while maintaining the interfacial tension between LDPE and PS constant. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 905–911, 2005     

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐ b‐styrene] on dielectric,thermal, and morphological characteristics of polypropylene/silica nanocomposites

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) copolymer on the thermal and dielectric properties of polypropylene (PP)—nanosilica (NS) composites in relation with morphological aspects revealed by atomic force microscopy (AFM) was investigated in this article. SEBS hindered the crystallization process of PP in PP/NS composites, leading to a smaller degree of crystallinity and lower perfection of crystalline structure. Broader lamellar thickness distribution was obtained in nanocomposites containing SEBS. Almost two times higher dielectric loss as compared to PP reference and two relaxation processes were detected in ε_r ^′′(f) curves of nanocomposites. The first peak, in the same frequency domain as for the references, was assigned to α‐relaxation of polymer components together with interfacial polarization. The relaxation time follows the Arrhenius law with an activation energy of 80–90 kJ/mol. For the second process, the temperature dependence of the relaxation times obeyed the VFT equation. The dielectric changes following the incorporation of SEBS support its tendency to hinder the motional processes in PP, in accordance with DSC results. A smooth transition from a phase rich in SEBS to one containing mainly PP was detected in the AFM image of the composite with the larger amount of SEBS, emphasizing the good compatibility at the PP/SEBS interface. POLYM. ENG. SCI., 53:2081–2092, 2013. © 2013 Society of Plastics Engineers     

The nature and location of SEBS–MA compatibilizer in polyethylene–wood flour composites

A maleic-anhydride-grafted styrene–ethylene—butylene–styrene (SEBS–MA) triblock copolymer has been used as a compatibilizer in low-density polyethylene–wood flour (LDPE–WF) composite system. The location of compatibilizer was studied using transmission electron microscopy (TEM). The unsaturated parts of the copolymer were stained with osmium tetraoxide (OsO₄) to enhance contrast between the different phases. TEM micrographs indicated that part of the compatibilizer was located at the interface between the wood particles and PE matrix and that wood was also stained by the OsO₄. The nature of the interface between the wood surface and the SEBS–MA was studied using Fourier transform infrared spectroscopy (FTIR). The results indicated that MA reacts with wood through esterification and hydrogen bonding and also possibly through interaction between the styrene and wood. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 201–209, 1998     

Impact,thermal, and morphological properties of functionalized rubber toughened‐poly(ethylene terephthalate) nanocomposites

In this study, poly(ethylene terephthalate)/organo‐montmorillonite (PET/OMMT) nanocomposites were melt‐compounded using twin screw extruder followed by injection molding. Maleic anhydride grafted styrene‐ethylene/butylene‐styrene (SEBS‐g‐MAH) was used to improve the impact properties of the PET/OMMT nanocomposites. The notched and un‐notched impact strength of PET/OMMT nanocomposites increased at about 2.5 times and 5.5 times by the addition of 5 wt % of SEBS‐g‐MAH. Atomic force microscopy (AFM) scans were taken from the polished surface of both PET/OMMT and SEBS‐g‐MAH toughened PET/OMMT nanocomposites. The addition of SEBS‐g‐MAH altered the phase structure and clay dispersion in PET matrix. It was found that some of the OMMT silicate layers were encapsulated by SEBS‐g‐MAH. Further, the addition of SEBS‐g‐MAH decreased the degree of crystallinity of the PET/OMMT nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Characteristics of impact modified polystyrene/organoclay nanocomposites

The poor impact resistance of Polystyrene (PS) was enhanced by the addition of elastomeric material, SEBS‐g‐MA. To prevent the reduction in strength and stiffness, organoclay Cloisite® 25A was used as filler and introduced into the matrix by a corotating twin screw extruder. Throughout the study, the clay content was kept at 2 wt%, whereas the content of SEBS‐g‐MA was varied between 5 and 40 wt%. It was found that Cloisite® 25A displays well dispersion in the ternary nanocomposites and the degree of dispersion increases with the elastomer content. The elastomeric phase has a greater viscosity than pure PS. Thus, as expected, at low elastomer contents, it forms the dispersed phase in the matrix as droplets. Transmission electron microscopy results show that the clay layers reside at the interphase between PS and elastomer and also inside the elastomeric phase. Owing to the location of the clay particles, the average elastomer domain size in ternary nanocomposites are found to be greater than that in the relative binary blends of PS‐(SEBS‐g‐MA). Moreover, with the organoclay addition, phase inversion point shifts to lower elastomer contents. The mechanical test results showed that the nanocomposites containing 15 and 20 wt% SEBS‐g‐MA have the optimum average domain size that results in high‐impact strength values without deteriorating the tensile properties. POLYM. COMPOS., 31:1853–1861, 2010. © 2010 Society of Plastics Engineers.     

In situ thermal reduction of graphene oxide in a styrene–ethylene/butylene–styrene triblock copolymer via melt blending

We report an in situ thermal reduction of graphene oxide (GO) in a styrene–ethylene/butylene–styrene (SEBS) triblock copolymer matrix during a melt‐blending process. A relatively high degree of reduction was achieved by melt‐blending premixed GO/SEBS nanocomposites in a Haake mixer for 25 min at 225 °C. Infrared spectral results revealed the successful thermal reduction of, and the strong adsorption of SEBS on, the graphene sheets. The glass transition temperature of polystyrene (PS) segments in SEBS was enhanced by the incorporation of thermally reduced graphene oxide (TRGO). The resultant TRGO/SEBS nanocomposites were used as a masterbatch to improve the mechanical properties of PS. Both the elongation at break and the flexural strength of PS/SEBS blends were enhanced with the addition of the TRGO. Our demonstration of the in situ thermal reduction of GO via melt blending is a simple, efficient strategy for preparing nanocomposites with well‐dispersed TRGO in the polymer matrix, which could be an important route for large‐scale fabrication of high‐performance graphene/polymer nanocomposites. © 2013 Society of Chemical Industry     

Comparison of the effect of carbon,halloysite and titania nanotubes on the mechanical and thermal properties of LDPE based nanocomposite films

In this study, titania nanotubes(TNTs) were prepared by hydrothermal method with the aim to compare the properties of these one-dimensional tubular nanostructures' reinforced nanocomposites with the carbon and halloysite nanotubes'(CNTs and HNTs, respectively) reinforced nanocomposites. Low density polyethylene(LDPE) was used as the matrix material. The prepared nanocomposites were characterized and compared by means of their morphological, mechanical and thermal properties. SEM results showed enhanced interfacial interaction and better dispersion of TNTs and HNTs into LDPE with the incorporation of a MAPE compatibilizer,however, these interactions seem to be absent between CNTs and LDPE, and the CNTs remained agglomerated.Contact angle measurements revealed that CNT filled nanocomposites are more hydrophilic than HNT composites, and less than TNT composites. CNTs provided better tensile strength and Young's modulus than HNT and TNT nanocomposites, a 42% increase in tensile strength and Young's modulus is achieved compared to LDPE.Tear strength improvement was noticed in the TNT composites with a value of 35.4 N·mm~(-1), compared to CNT composites with a value of 25.5 N·mm~(-1)·s~(-1). All the prepared nanocomposites are more thermally stable than neat LDPE and the best improvement in thermal stability was observed for CNT reinforced nanocomposites.CNTs depicted the best improvement in tensile and thermal properties and the MAPE compatibilizer effectiveness regarding morphological. mechanical and thermal properties was only observed for TNT and HNT systems.     

Effect of POSS‐grafted titanium dioxide on the electrical and thermal properties of LDPE/TiO2 polymer nanocomposite

Two types of nanocomposites have been fabricated by a ball‐milling technique. The first type consists of untreated titanium dioxide (TiO₂) incorporated into low‐density polyethylene (LDPE). For the second one, TiO₂ filler chemically treated with trisilanol phenyl–polyhedral oligomeric silsesquioxane (TP–POSS) as compatibilizing agent was ball‐milled with LDPE. All specimens were tested by microstructure analysis and thermal, dielectric characterization techniques. Microstructure analysis by atomic force microscopy and scanning electron microscopy show clearly an increased dispersion in presence of POSS. Scanning electron microscopy even shows the formation of a particular structure due possibly to interactions between functionalization. It was observed that the modification of the surface of TiO₂ by the POSS decreased the dielectric loss. All nanocomposites containing treated TiO₂ revealed an improvement in thermal conductivity, with the most distinct value of 19% in case of LDPE containing 5 wt % treated TiO₂. The incorporation of TiO₂ fillers seems to reduce the dielectric breakdown strength of the nanocomposites. However, nanocomposites containing 3 and 5 wt % treated TiO₂ have exhibited a slightly enhancement in dielectric breakdown strength up to 5%. The improvement in surface resistance to partial discharge was found in all nanocomposites specimens, especially for both types of composite containing 7 wt % untreated and treated TiO₂. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46095.     

Effects of the compatibilizer structural parameters on microstructural formation in ethylene–propylene–diene monomer rubber/ethylene–propylene–diene monomer rubber‐g‐maleic anhydride/organoclay nanocomposites

Nanocomposite vulcanizates based on ethylene–propylene–diene monomer rubber (EPDM) and organically modified montmorillonite with improved mechanical and barrier properties were prepared via a melt‐mixing process in the presence of maleic anhydride grafted ethylene–propylene–diene monomer rubber (EPDM‐g‐MAH) as an interfacial compatibilizer. The effects of the EPDM Mooney viscosity as the matrix and also the compatibilizer molecular weight and its maleation degree on the developed microstructure were also studied. The annealing of the vulcanized nanocomposites based on a low‐Mooney‐viscosity EPDM matrix and low‐Mooney‐viscosity EPDM‐g‐MAH enhanced the flocculation of the dispersed clay platelets; this implied that the flocculated structure for the clay nanolayers was more thermodynamically preferred in these nanocomposites. This was verified by the decrease in the oxygen permeability of the nanocomposite vulcanizates with increasing annealing time. The tendency of the clay nanosilicate layers to flocculate within the matrix of EPDM was found to be influenced by the clay volume fraction, the maleation degree, and also, the Mooney viscosity of the compatibilizer. Interfacially compatibilized nanocomposites based on high‐molecular‐weight EPDM exhibited a more disordered dispersion of the clay nanolayers, with a broadened relaxation time spectra; this was attributed to the higher shearing subjected to the mix during the melt‐blending process. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Analysis and modeling of modified styrene–acrylonitrile/carboxylated acrylonitrile butadiene rubber nanocomposites filled with graphene and graphene oxide: Interfacial interaction and nonlinear elastoplastic behavior

Nonlinear elastoplastic behavior of the nanocomposites based on the styrene–acrylonitrile/carboxylated acrylonitrile butadiene rubber (SAN/XNBR) blend was investigated using experimental and theoretical analysis. Graphene, graphene oxide nanoparticles, and glycidyl methacrylate-grafted-XNBR (XNBR-g-GMA) as a compatibilizer were incorporated in the SAN/XNBR blends. In this regard, the focus of this study is on modeling of the stress–strain behavior of these nanocomposites, considering the effect of the interfacial interactions made by compatibilizer. For this purpose, field emission scanning electron microscopy (FESEM) and transmission electron microscope (TEM) techniques were used to investigate the relationship between microstructure and mechanical properties of nanocomposites. In addition, FESEM and TEM images showed that the presence of a compatibilizer could influence the dispersion and localization of the nanoparticles. According to the tensile test results, the presence of the compatibilizer increased the mechanical properties of the nanocomposites, specifically elongation at break. Considering the nanocomposite containing compatibilizer and graphene oxide, the elongation at break increased about 570% compared with the nanocomposite without compatibilizer. Better dispersion of graphene oxide and the creation of chemical interaction among components in the presence of the XNBR-g-GMA compatibilizer could be the reasons for these improvements, as confirmed by TEM. The usage of the Bergstrom–Boyce model for analyzing the nonlinear elastoplastic behavior of the nanocomposites illustrated proper conformity with the experimental data in the elastic region. However, there are some deviations in the viscoplastic region, particularly close to the breaking elongation region.     

Preparation and characterization of low density polyethylene/ethylene methyl acrylate glycidyl methacrylate/organoclay nanocomposites

The effects of organoclay type, compatibilizer, and the addition order of components during melt‐blending process on the morphology and thermal, mechanical, and flow properties of ternary nanocomposites based on low‐density polyethylene (LDPE) were investigated. As a compatibilizer, ethylene/methyl acrylate/glycidyl methacrylate (E‐MA‐GMA), as organoclays Cloisites® 15A, 25A, and 30B were used. All samples were prepared by a corotating twin screw extruder, followed by injection molding. The highest increase of the basal spacing for ternary nanocomposites was obtained in LDPE/E‐MA‐GMA/Cloisite® 30B nanocomposites with interlayer spacing of 59.2 Å. Organoclay and compatibilizer addition did not influence the melting/crystallization behavior of the compositions, and both compatibilizer and organoclays had no significant nucleation activity in LDPE. Among the ternary nanocomposites, the maximum increase in tensile strength and tensile modulus values was observed for nanocomposites containing organoclay Cloisite® 15A. The improvement with respect to neat LDPE was 43% for tensile strength and 44% for tensile modulus. According to the mechanical analysis, the best sequence of component addition was the one in which LDPE, organoclay, and compatibilizer were simultaneously fed to the extruder in the first run, and the product of the first run was extruded once more. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polypropylene/clay nanocomposites: Combined effects of clay treatment and compatibilizer polymers on the structure and properties

Combined effects of clay treatment and compatibilizer polymers on the structure and properties of polypropylene/clay nanocomposites were studied. Dynamic mechanical analysis was used to analyze comparatively the dynamic mechanical response of different nanocomposites prepared from polypropylene and montmorillonite‐rich bentonite, and to relate such response with the material microstructure. Two different bentonites were used: a purified Spanish natural bentonite was organophillized by means of 11‐undecyl‐ammonium ion and a commercial bentonite organophillized with dimethyl dehydrogenated tallow ammonium ion. Three different polar copolymers were employed as compatibilizer agents in some of the formulations: maleic anhydride‐grafted polypropylene, maleic anhydride‐grafted poly(styrene‐co‐ethylenebutylene‐co‐styrene), and poly(ethylene terephthalate‐co‐isophthalate) (PET). To ascertain the microstructure characteristics in the nanocomposites, wide angle X‐ray diffraction, transmission electron microscopy, and differential scanning calorimetry techniques were used. The nanocomposites containing both bentonite organophillized with 11‐undecyl‐ammonium ion and PET, and maleated PP as compatibilizer system, were found to have the highest storage modulus and the smallest loss factor values, which was mainly due to the better clay platelets dispersion. The dynamic mechanical response of nanocomposites prepared with bentonite organophillized with dimethyl dehydrogenated tallow ammonium ion and maleated SEBS was strongly affected by the presence of this compatibilizer. The temperature of PP and α, β, and γ relaxations strongly depended on the interactions between the different phases in the nanocomposites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1213–1223, 2006     

Preparation of a long-alkyl-chain silane grafted organic montmorillonite and its nanocomposite with SEBS

In this study, a modified montmorillonite (W-H-OMMT) was prepared by intercalating pristine montmorillonite using a phosphorus salt and a subsequent grafting using a long-alkyl-chain silane, and the nanocomposites with poly[styrene–(ethylene-co-butylene)–styrene] (SEBS) were prepared by melt blending. The pristine and the modified MMT were characterized by XRD, FT-IR, XPS and SEM. The morphology of the SEBS nanocomposites was studied using XRD, SEM and TEM, and the results can be correlated well with transparency, color, surface contact angle, rheological behavior, thermal and mechanical properties of the nanocomposites. As compared with pristine and the modified clay, more uniform dispersion and improved compatibility are observed for the W-H-OMMT in the SEBS matrix, resulting in better transparency and more hydrophobic surface for the SEBS/W-H-OMMT nanocomposite. Better thermal stability, a synergetic effect in tensile strength and elongation at break were observed, which can be attributed to well dispersion of the W-H-OMMT, as well as perfect adhesion between the W-H-OMMT and the SEBS matrix from the enhanced molecular interaction between the long-alkyl chain and the SEBS molecules. Compared to pure SEBS, the strength and elongation of SEBS/W-H-OMMT nanocomposite increased by 8.5 and 7.6 %; meanwhile, the water contact angel and the 50 % weight loss temperature increased by 5.3 and 13.1 %, respectively. Appropriate silane grafted organic montmorillonite provided an efficient way for the overall performance improvement of SEBS.     

Thermo‐oxidative decomposition kinetics of elastomeric composites based on styrene‐(ethylene‐butylene)‐styrene triblock copolymer and organomontmorillonite

The elastomeric nanocomposites based on organomontmorillonite (OMMT) and styrene‐(ethylene‐butylene)‐styrene (SEBS) thermoplastic elastomer were prepared by melt processing using maleic anhydride grafted SEBS (SEBS‐g‐MA) as compatibilizer. Thermo‐oxidative decomposition behavior of the neat components and the nanocomposites were investigated using thermogravimertic analysis (TGA) in air atmosphere. The isoconversional method is employed to study the kinetics of thermo‐oxidative degradation. The heating modes and the composition of nanocomposites were found to affect the kinetic parameters (E_a, lnA and n). The E_a and lnA values of SEBS, OMMT, and their composites are much higher under dynamic heating than under isothermal heating. The reaction order (n) of OMMT was lower than those of SEBS and their composites. The obtained TG profiles and calculated kinetic parameters indicated that the incorporation of OMMT into SEBS significantly improved the thermal stability both under dynamic heating and under isothermal heating. The simultaneously obtained DSC data showed that the enthalpy of thermal decomposition decreased with OMMT loading. No significant change in the nonisothermal and isothermal stability of the nanocomposites with addition of SEBS‐g‐MA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011