Uniformity of gallium doped zinc oxide thin film prepared by pulsed laser deposition

Recently, transparent conducting oxide thin films have attracted attention for the application to transparent conducting electrodes. In this work, we evaluated the uniformity of electrical, optical and structural properties for gallium doped zinc oxide thin films prepared on the 10 × 10 cm² silica glass substrate by pulsed laser deposition. The resistivity, carrier concentration, mobility, bonding state and atomic composition of the film were uniform along in-plane and depth direction over the 10 × 10 cm² area of the substrate. The film showed the average transmittance of 81-87%, resistivity of 1.4 × 10^− 3 Ω cm, carrier concentration of 9.7 × 10²⁰/cm³ and mobility of 5 cm²/Vs in spite of the amorphous X-ray diffraction pattern. The gradual thickness distribution was found, however, the potential for large-area and low temperature deposition of transparent conducting oxide thin film using pulsed laser deposition method was confirmed.     

Threshold voltage shift by controlling Ga in solution processed Si-In-Zn-O thin film transistors

The threshold voltage change of solution processed gallium-silicon-indium-zinc oxide (GSIZO) thin film transistors (TFTs) annealed at 200 °C has been investigated depending on gallium ratio. GSIZO thin films were formed with various gallium ratios from 0.01 to 1 M ratio. The 30 nm-thick GSIZO film exhibited optimized electrical characteristics, such as field effect mobility (μ_FE) of 2.2 × 10^− 2 cm²/V·s, subthreshold swing (S.S) of 0.11 V/dec, and on/off current ratio (I_on/off) of above 10⁵. The variation of gallium metal cation has an effect on the threshold voltage (V_th) and the field effect mobility (μ_FE). The V_th was shifted toward positive direction from − 5.2 to − 0.4 V as increasing gallium ratio, and μ_FE was decreased from 2.2 × 10^− 2 to 5 × 10^− 3 cm²/V s. These results indicated that gallium was acted as carrier suppressor by degenerating oxygen vacancy. The electrical property of GSIZO TFTs has been analyzed as a function of the gallium ratio in SIZO system, and it clearly showed that variation of gallium contents could change on the performance of TFTs.     

Properties of n-type ZnN thin films as channel for transparent thin film transistors

In this work we fabricated, by rf magnetron sputtering from a ZnN target, zinc nitride thin films and examined their properties in order to be used as channel layer in thin film transistors. The films were deposited at 100 W rf power and the Ar pressure was 5 mTorr. The zinc nitride thin films were n-type, and depending on the thickness they exhibited low resistivity (10-10^− 2 Ohm?cm), high carrier concentration (10¹⁸-10²⁰ cm^− 3) and very low transmittance values due to the excess zinc in their structure. After annealing at 300 °C, in flowing nitrogen, the films became more conductive, but annealing at higher temperatures deteriorated the electrical properties and became transparent. Transparent thin film transistor having zinc nitride as channel layer exhibited promising transistor characteristics after nitrogen annealing. Improvements in output transistor characteristics due to both material (zinc nitride) and transistor optimization are addressed.     

Transparent conducting Al and Y codoped ZnO thin film deposited by DC sputtering

Transparent conducting Al and Y codoped zinc oxide (AZOY) thin films with high transparency and low resistivity were deposited by DC magnetron sputtering. The effects of substrate temperature on the structural, electrical and optical properties of AZOY thin films deposited on glass substrates have been investigated. X-ray diffraction spectra indicate that no diffraction peak of Al₂O₃ or Y₂O₃ except that of ZnO (0 0 2) is observed. The AZOY thin film prepared at substrate temperature of 250 °C has the optimal crystal quality inferring from FWHM of ZnO (0 0 2) diffraction peak, but the AZOY thin film deposited at 300 °C has the lowest resistivity of 3.6 × 10⁻⁴ Ω-cm, the highest mobility of 30.7 cm² V⁻¹ s⁻¹ and the highest carrier concentration of 5.6 × 10²⁰ cm⁻³. The films obtained have disorderly polyhedral surface morphology indicating possible application in thin film solar cell with good quality and high haze factor without the need of post-deposition etching.     

Effect of Ag doping on the performance of ZnO thin film transistor

Ag-doped zinc oxide (SZO) thin film transistors (TFTs) have been fabricated using a back-gate structure on thermally oxidized and heavily doped p-Si (100) substrate. The SZO thin films were deposited via pulsed laser deposition (PLD) from a 1, 3, and 5 wt.% Ag-doped ZnO (1SZO, 3SZO, and 5SZO, respectively) target using a KrF excimer laser (λ, 248 nm) at oxygen pressure of 350 mTorr. The deposition carried out at both room-temperature (RT) and 200 °C. The SZO thin films had polycrystalline phase with preferred growth direction of (002) as well as a wurtzite hexagonal structure. Compare with ZnO thin films, the SZO thin films were characterized by confirming the shift of (002) peak to investigate the substitution of Ag dopants for Zn sites. The as-grown SZO TFTs deposited at RT and 200 °C showed insulator characteristics. However the SZO TFTs annealed at 500 °C showed good n-type TFT performance because Ag was diffused from Zn lattice site and bound themselves at the high temperature, and it caused generation of electron carriers. The post-annealed 5SZO TFT deposited at 500 °C exhibited a threshold voltage (V_th) of 11.5 V, a subthreshold swing (SS) of 2.59 V/decade, an acceptable mobility (μ_SAT) of 0.874 cm²/V s, and on-to-off current ratios (I_on/off) of 1.44 × 10⁸.     

Non-aqueous solution processed ZnO thin film transistors

Zinc oxide based thin film transistors (TFT) fabricated by a non-aqueous sol-gel solution process with a zinc neodecanoate precursor are demonstrated. X-ray diffraction measurement reveals that the ZnO films adopt a hexagonal structure with a random crystal orientation. Atomic force microscope and scanning electron microscope characterizations show that the films are closely packed and consisted of particles with an average size of 45 nm. The devices exhibit an n-channel enhancement mode behavior, with saturation mobility in the range of 0.95-1.29 cm² V⁻¹ s⁻¹, drain current on-to-off ratios higher than 10⁷ and threshold voltages between 5.3 and 16.8 V in an ambient environment. The results imply that high-performance ZnO TFTs produced by a simple and low-cost technique could be applicable to electronic devices.     

Structural and optical properties of Ti-doped ZnO thin films prepared by the cathodic vacuum arc technique with different annealing processes

Highly transparent Ti-doped ZnO thin films were prepared on glass substrates at a deposition rate of approximately 33 nm/min using the cathodic vacuum arc technique with a Zn target power of 550 W and a Ti target power of 750 W, respectively. X-ray diffraction measurements have shown that the Ti-doped ZnO thin film with a vacuum post-annealing condition is c-axis oriented but an amorphous phase at the other post-annealing atmosphere and as-deposited condition. Transmittance measurements show that the best optical quality of the Ti-doped ZnO thin films occurred at a post-annealing atmosphere of N₂/H₂ mixed gases. Additionally, the optical transmittance of all films has been found more than 85% in a range of 500-700 nm. The lowest electrical resistivity was 3.48 × 10⁻³ Ω cm, obtained on as-deposited films. However, the post-annealing condition greatly increased the resistivity.     

High performance self-aligned top-gate ZnO thin film transistors using sputtered Al2O3 gate dielectric

High performance self-aligned top-gate zinc oxide (ZnO) thin film transistors (TFTs) utilizing high-k Al₂O₃ thin film as gate dielectric are developed in this paper. Good quality Al₂O₃ thin film was deposited by reactive DC magnetron sputtering technique using aluminum target in a mixed argon and oxygen ambient at room temperature. The resulting transistor exhibits a field effect mobility of 27 cm²/V s, a threshold voltage of − 0.5 V, a subthreshold swing of 0.12 V/decade and an on/off current ratio of 9 × 10⁶. The proposed top-gate ZnO TFTs in this paper can act as driving devices in the next generation flat panel displays.     

Investigation on indium concentration dependence of solution processed indium tin oxide thin film transistors

The effect of the indium content in indium tin oxide (ITO) films fabricated using a solution-based process and ITO channel thin film transistors (TFTs) was examined as a function of the indium mole ratio. The carrier concentration and resistivity of the ITO films could be controlled by the appropriate treatments. The TFTs showed an increase in the off-current due to the enhanced conductivity of the ITO channel layer with increasing indium mole ratios, producing an increase in the field effect mobility. The characteristics of the a-ITO channel TFT showed the best performance (μ_FE of 3.0 cm² V^− 1 s^− 1, V_th of 2.0 V, and S value of 0.4 V/decade) at In:Sn = 5:1.     

Highly conducting and transparent tin-doped CdO thin films for optoelectronic applications

Highly conducting and transparent thin films of tin-doped cadmium oxide were deposited on quartz substrate using pulsed laser deposition technique. The effect of growth temperature on structural, optical and electrical properties was studied. These films are highly transparent (78-89%) in visible region, and transmittance of the films depends on growth temperature. It is observed that resistivity increases with growth temperature after attaining minimum at 150 °C, while carrier concentration continuously decreases with temperature. The lowest resistivity of 1.96 × 10^− 5 Ω cm and carrier concentration of 5.52 × 10²¹ cm³ is observed for the film grown at 150 °C. These highly conducting and transparent tin-doped CdO thin films grown via pulsed laser deposition could be an excellent candidate for future optoelectronic applications.     

Improvement in the negative bias temperature stability of ZnO based thin film transistors by Hf and Sn doping

We assessed the performance of ZnO TFTs using Si₃N₄ gate dielectrics after various treatments. A remarkable improvement in the transfer characteristics was obtained for the O₂ plasma treated ZnO TFT and SiO₂ interlayer deposited ZnO TFT. Also, we developed amorphous hafnium-zinc-tin oxide (HZTO) thin film transistors (TFTs) and investigated the influence of hafnium (Hf) doping on the electrical characteristics of the hafnium-zinc oxide (HZO) thin film transistors. Doping with Hf can decrease the carrier concentration, which may result from a decrease of the field effect mobility, and reduce oxygen vacancy related defects in the interfacial layer. Adding tin (Sn) can suppress the growth of a crystalline phase in the HZTO films. The HZTO TFTs exhibited good electrical properties with a field effect mobility of 14.33 cm²/Vs, a subthreshold swing of 0.97 V/decade, and a high I_ON/OFF ratio of over 10⁹.     

Annealing effect on dielectric and leakage current characteristics of Mn-doped Ba0.6Sr0.4TiO3 thin films as gate insulators for low voltage ZnO thin film transistor

We report on the dielectric properties and leakage current characteristics of 3 mol% Mn-doped Ba_0.6Sr_0.4TiO₃ (BST) thin films post-annealed up to 600 °C following room temperature deposition. The suitability of 3 mol% Mn-doped BST films as gate insulators for low voltage ZnO thin film transistors (TFTs) is investigated. The dielectric constant of 3 mol% Mn-doped BST films increased from 24 at in-situ deposition up to 260 at an annealing temperature of 600 °C due to increased crystallinity and the formation of perovskite phase. The measured leakage current density of 3 mol% Mn-doped BST films remained on the order of 5 × 10^− 9 to 10^− 8 A/cm² without further reduction as the annealing temperature increased, thereby demonstrating significant improvement in the leakage current characteristics of in-situ grown Mn-doped BST films as compared to that (5 × 10^− 4 A/cm² at 5 V) of pure BST films. All room temperature processed ZnO-TFTs using a 3 mol% Mn-doped BST gate insulator exhibited a field effect mobility of 1.0 cm²/Vs and low voltage device performance of less than 7 V.     

Preparation of zinc tin oxide films by reactive magnetron sputtering of Zn on liquid Sn

Zn is sputter-deposited on melted Sn films by radio-frequency magnetron sputtering in oxidizing plasma. The samples present an absorption cut-off wavelength close to the one of ZnO, and an optical transparency higher than 50% in the visible range. Ex-situ thermal annealing improves visible transparency and produces a slight blue-shift in the optical bandgap. X-ray diffraction patterns show typical spectra due to polycrystalline ZnO with evidence of the presence of crystalline SnO, before annealing, and Zn₂SnO₄, after annealing. Rutherford Backscattering studies reveal the existence of a ZnO layer on top of an O-rich (Zn, Sn)O thin film. After optimal thermal treatment, electrical characterization exhibits carrier concentrations of 10¹⁶-10¹⁷ cm⁻³ and mobilities of 20-80 cm² V⁻¹ s⁻¹ for the resulting (Zn, Sn)O n-type films.     

Effect of process parameters on the growth and properties of impurity-doped zinc oxide transparent conducting thin films by RF magnetron sputtering

Zinc oxide transparent conducting thin films co-doped with aluminum and ruthenium were grown on polyethylene terephthalate substrates at room temperature using RF magnetron sputtering. The crystal growth and physical properties of the films were investigated with respect to the variation of discharge power density from 1.5 to 6.1 W/cm² and sputtering pressure from 0.13 to 2.0 Pa. X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) showed that the films grown with 3.6 W/cm² power density and sputtering pressure of 0.4 Pa had the best crystallinity and larger pyramid-like grains. The optimized electrical resistivity had a lowest measured value of about 9 × 10⁻⁴ Ω cm. The low carrier mobilities of the films (3-8.9 cm² V⁻¹ s⁻¹) have been discussed in terms of what is believed to be the dominant effect of ionized impurity scattering, but in addition chemisorption of oxygen on the film surface and effect of grain boundaries are also thought to be significant. The transmittances of the films in the visible range are greater than 80%, while the optical band gaps are in the order of 3.337-3.382 eV.     

Ultrathin Al-doped transparent conducting zinc oxide films fabricated by pulsed laser deposition

Al-doped transparent conducting zinc oxide (AZO) films, approximately 20-110 nm-thick, were deposited on glass substrates at substrate temperatures between 200 and 300 °C by pulsed laser deposition (PLD) using an ArF excimer laser (λ = 193 nm). When fabricated at a substrate temperature of 260 °C, a 40-nm-thick AZO film showed a low resistivity of 2.61 × 10^− 4 Ω·cm, carrier concentration of 8.64 × 10²⁰ cm^− 3, and Hall mobility of 27.7 cm²/V·s. Furthermore, for an ultrathin 20-nm-thick film, a resistivity of 3.91 × 10^− 4 Ω·cm, carrier concentration of 7.14 × 10²⁰ cm^− 3, and Hall mobility of 22.4 cm²/V·s were obtained. X-ray diffraction (XRD) spectra, obtained by the θ-2θ method, of the AZO films grown at a substrate temperature of 260 °C showed that the diffraction peak of the ZnO (0002) plane increased as the film thickness increased from 20 to 110 nm. The full-width-at-half-maximum (FWHM) values were 0.5500°, 0.3845°, and 0.2979° for film thicknesses of 20, 40, and 110 nm, respectively. For these films, the values of the average transmittance in visible light wavelengths (400-700 nm) were 95.1%, 94.2%, and 96.6%, respectively. Field emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM) observations showed that even the 20-nm-thick films did not show island structures. In addition, exfoliated areas or vacant and void spaces were not observed for any of the films.     

Electrical transport parameters of heavily-doped zinc oxide and zinc magnesium oxide single and multilayer films heteroepitaxially grown on oxide single crystals

Heavily doped epitaxial ZnO:Al and Zn_1−xMg_xO:Al films were grown by radio frequency magnetron sputtering onto single crystalline substrates (sapphire, MgO, silicon) and characterized by structural and electrical measurements. It is the aim of this investigation to better understand the carrier transport and the doping mechanisms in heavily doped transparent conducting oxide (TCO) films. It was found that the crystallographic film quality determines only partly the mobilities and the carrier concentrations: ZnO:Al films on a-plane (110) sapphire and on MgO (100) exhibit the highest mobilities. The oxygen partial pressure during the deposition from ceramic targets is more important influencing especially the carrier concentration N of the films. Though the films grew epitaxially grain boundaries are still existent, which reduce the mobility due to electrical grain boundary barriers for N < 3 · 10²⁰ cm^− 3. From annealing experiments the role of point defects and dislocations for the carrier transport could be estimated. For carrier concentrations above 3 · 10²⁰ cm^− 3 ionized impurity scattering limits the mobility, which is in agreement with our earlier review [K. Ellmer, J. Phys. D: Appl. Phys. 34 (2001) 3097].     

Effect of inserting a buffer layer on the characteristics of transparent conducting impurity-doped ZnO thin films prepared by dc magnetron sputtering

In transparent conducting impurity-doped ZnO thin films prepared on glass substrates by a dc magnetron sputtering (dc-MS) deposition, the obtainable lowest resistivity and the spatial resistivity distribution on the substrate surface were improved by a newly developed MS deposition method. The decrease of obtainable lowest resistivity as well as the improvement of spatial resistivity distribution on the substrate surface in Al- or Ga-doped ZnO (AZO or GZO) thin films were successfully achieved by inserting a very thin buffer layer, prepared using the same MS apparatus with the same target, between the thin film and the glass substrate. The deposition of the buffer layer required a more strongly oxidized target surface than possible to attain during a conventional dc-MS deposition. The optimal thickness of the buffer layer was found to be about 10 nm for both GZO and AZO thin films. The resistivity decrease is mainly attributed to an increase of Hall mobility rather than carrier concentration, resulting from an improvement of crystallinity coming from insertion of the buffer layer. Resistivities of 3 × 10^− 4 and 4 × 10^− 4Ω cm were obtained in 100 nm-thick-GZO and AZO thin films, respectively, incorporating a 10 nm-thick-buffer layer prepared at a substrate temperature around 200 °C.     

Structural and optoelectronic properties of Al-doped zinc oxide films deposited on flexible substrates by radio frequency magnetron sputtering

Al-doped zinc oxide (AZO) thin films were deposited onto flexible polyethylene terephthalate substrates, using the radio frequency (RF) magnetron sputtering process, with an AZO ceramic target (The Al₂O₃ content was about 2 wt.%). The effects of the argon sputtering pressure (in the range from 0.66 to 2.0 Pa), thickness of the Al buffer layer (thickness of 2, 5, and 10 nm) and annealing in a vacuum (6.6 × 10^− 4 Pa), for 30 min at 120 °C, on the morphology and optoelectronic performances of AZO films were investigated. The resistivity was 9.22 × 10^− 3 Ω cm, carrier concentration was 4.64 × 10²¹ cm^− 3, Hall mobility was 2.68 cm²/V s and visible range transmittance was about 80%, at an argon sputtering pressure of 2.0 Pa and an RF power of 100 W. Using an Al buffer decreases the resistivity and optical transmittance of the AZO films. The crystalline and microstructure characteristics of the AZO films are improved by annealing.     

Effect of spatial relationship between arc plasma and substrate on the properties of transparent conducting Ga-doped ZnO thin films prepared by vacuum arc plasma evaporation

The effect of the spatial relationship between the arc plasma flow and the substrate surface on the resulting film thickness and electrical properties is investigated in transparent conducting Ga-doped ZnO (GZO) thin films deposited by a vacuum arc plasma evaporation (VAPE) method. It was found that the resulting electrical properties of GZO thin films produced by a VAPE deposition on a fixed substrate were considerably dependent on both the film thickness and the location on the substrate surface, extending from the area nearest the arc plasma source to that at the opposite end of the substrate in a direction parallel to the arc plasma flow; with GZO thin films deposited with various thicknesses in the range from 20 to 200 nm, the films exhibited a thickness dependence of resistivity that was considerably affected by the location on the substrate surface. The variation of resistivity relative to the location on the substrate surface was related to that of carrier concentration, which is mainly attributed to the distribution of the amount of oxygen reaching the substrate surface. In GZO thin films deposited with a thickness of 30-40 nm at a substrate temperature of 250 °C, a resistivity as low as 4 × 10^− 4 Ω cm was obtained in the area of the substrate nearest the arc plasma source.     

Silicon metal-semiconductor-metal photodetector with zinc oxide transparent conducting electrodes

Transparent conducting oxides thin layers, due to their optical and electrical properties, can be used as transparent electrodes in various optoelectronic devices. We present a metal-semiconductor-metal photodiode (MSM-PD) on silicon as optically active layer with zinc oxide (ZnO) thin layer as interdigitated Schottky transparent electrodes. The advantage of using a ZnO thin layer as Schottky electrodes consists in the improvement of the photoresponse by eliminating the shadowing of the active area by opaque metallic electrodes. ZnO thin layers were deposited on 10 Ω cm resistivity silicon epitaxial wafers by the vacuum thermal evaporation method. High purity metallic powders were mixed with an (Al + Sn)/Zn ratio of 0.03. In order to obtain transparent layers the metallic depositions were thermally treated at 450 °C for 2 h. The Al, Sn co-doped ZnO layers of 0.5-0.8 μm were investigated regarding structural, optical and electrical properties and surface morphology. The obtained thin layers have a high transparency (T > 85%) over a large spectral range and the resistivity is quite low, ρ ~ 10^− 4 Ω cm. The interdigitated Schottky contacts of ZnO were configurated onto the optically active Si layer providing an MSM-PD structure of 0.143 mm² active area and finger spacing and finger width of 6 μm. The optoelectronic characteristics were measured and the Schottky barrier height of 0.62 eV was determined from the current-voltage characteristic. A responsivity of 0.2 A/W at 475 nm and a capacitance of 1.4 pF at 10 V bias were obtained for the MSM-PD structure with transparent conducting ZnO Schottky electrodes.