Microstructure, ferroelectric, and piezoelectric properties of (1 − x − y)Bi0.5Na0.5TiO3-xBaTiO3-yBi0.5Ag0.5TiO3 lead-free ceramics

Lead-free (1 − x − y)Bi_0.5Na_0.5TiO₃-xBaTiO₃-yBi_0.5Ag_0.5TiO₃ (BNT-BT-BAT-x/y, x = 0-0.10, y = 0-0.075) piezoelectric ceramics were synthesized by conventional oxide-mixed method. The microstructure, ferroelectric, and piezoelectric properties of the ceramics were investigated. Results show that a morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases of BNT-BT-BAT-x/0.04 ceramics is formed at x = 0.06-0.08. The addition of BAT has no obvious change on the crystal structure of BNT-BT ceramics while it causes the grain size of the ceramics to become more homogenous. Near the MPB, the ceramics with x = 0.06 and y = 0.05-0.06 possess optimum electrical properties: P_r ∼ 42.5 μC/cm², E_c ∼ 32.0 kV/cm, d₃₃ ∼ 172 pC/N, k_p ∼ 32.6%, and k_t ∼ 52.6%. The temperature dependences of k_p and polarization versus electric hysteresis loops reveal that the depolarization temperature (T_d) of BNT-BT-BAT-0.06/y ceramics decreases with increasing y. In addition, the polar and non-polar phases may coexist in the BNT-BT-BAT-x/y ceramics above T_d.     

Preparation and electrical properties of Bi0.5Na0.5TiO3-BaTiO3-KNbO3 lead-free piezoelectric ceramics

Lead-free (1 − x)Bi_0.47Na_0.47Ba_0.06TiO₃-xKNbO₃ (BNBT-xKN, x = 0-0.08) ceramics were prepared by ordinary ceramic sintering technique. The piezoelectric, dielectric and ferroelectric properties of the ceramics are investigated and discussed. The results of X-ray diffraction (XRD) indicate that KNbO₃ (KN) has diffused into Bi_0.47Na_0.47Ba_0.06TiO₃ (BNBT) lattices to form a solid solution with a pure perovskite structure. Moderate additive of KN (x ≤ 0.02) in BNBT-xKN ceramics enhance their piezoelectric and ferroelectric properties. Three dielectric anomaly peaks are observed in BNBT-0.00KN, BNBT-0.01KN and BNBT-0.02KN ceramics. With the increment of KN in BNBT-xKN ceramics, the dielectric anomaly peaks shift to lower temperature. BNBT-0.01KN ceramic exhibits excellent piezoelectric properties and strong ferroelectricity: piezoelectric coefficient, d₃₃ = 195 pC/N; electromechanical coupling factor, k_t = 58.9 and k_p = 29.3%; mechanical quality factor, Q_m = 113; remnant polarization, P_r = 41.8 μC/cm²; coercive field, E_c = 19.5 kV/cm.     

High permittivity and low dielectric loss of the Ca1−xSrxCu3Ti4O12 ceramics

The Ca_1−xSr_xCu₃Ti₄O₁₂ (CSCTO) giant dielectric ceramics were prepared by conventional solid-state method. X-ray diffraction patterns revealed that a small amount of Sr²⁺ (x < 0.2) had no obvious effect on the phase structure of the CSCTO ceramics, while with increasing the Sr²⁺ content, a second phase of SrTiO₃ appeared. Electrical properties of CSCTO ceramics greatly depended on the Sr²⁺ content. The Ca_0.9Sr_0.1Cu₃Ti₄O₁₂ ceramics exhibited a higher permittivity (71,153) and lower dielectric loss (0.022) when measured at 1 kHz at room temperature. The ceramics also performed good temperature stability in the temperature range from −50 °C to 100 °C at 1 kHz. By impedance spectroscopy analysis, all compounds were found to be electrically heterogeneous, showing semiconducting grains and insulating grain boundaries. The grain resistance was 1.28 Ω and the grain boundary resistance was 1.31 × 10⁵ Ω. All the results indicated that the Ca_0.9Sr_0.1Cu₃Ti₄O₁₂ ceramics were very promising materials with higher permittivity for practical applications.     

Dielectric and magnetic behavior of BaCd2−xSrxFe16O27 W-type hexagonal ferrites

We have prepared BaCd_2−xSr_xFe₁₆O₂₇ (x = 0, 0.5, 1, 1.5 and 2.0) W-type hexagonal ferrites by standard ceramic method. In this work, the structural, dielectric and magnetic properties have been studied of the prepared samples. The XRD analysis of the samples reveals single phase behavior sintered at 1400 °C for 6 h. The saturation magnetization (M_s) shows increasing behavior with the increasing concentration of Sr²⁺. While the coercivity (H_c) decreases rapidly up to 409 G for x = 1.5 and then increases for (x > 1.5) due to the preference of Cd²⁺ for tetrahedral sites and the number of spin-down magnetic ions. The real and imaginary parts of the dielectric constant (?′,?″) and dielectric loss tangent (tan δ) are determined in the frequency range 0.1-10⁷ Hz. It is observed that both the real and imaginary parts of the dielectric constant and tan δ decrease with the increasing concentration of Sr²⁺, which is due to the contribution of Cd²⁺ ions in addition to Fe³⁺ and Fe²⁺ ions to interfacial polarization.     

Piezoelectric and dielectric properties of Dy2O3-doped (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ + x wt% Dy₂O₃ with x = 0-0.3 ceramics were synthesized by conventional solid-state processes. The effects of Dy₂O₃ on the microstructure, the piezoelectric and dielectric properties were investigated. X-ray diffraction pattern confirmed that the coexistence of tetragonal and rhombohedral phases in the (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ composition was not changed by adding 0.05-0.3 wt% Dy₂O₃. SEM images indicate that all the ceramics have pore-free microstructures with high density, and that doping of Dy₂O₃ inhibits the grain growth of the ceramics. The addition of Dy₂O₃ shows the double effects on decreasing the piezoelectric and dielectric properties for 0 < x < 0.15 when Dy³⁺ ions substitute B-site Ti⁴⁺ ions, and increasing the properties for 0.15 < x < 0.3 when Dy³⁺ ions enters into A-site of the perovskite structure. The optimum electric properties of piezoelectric constant d₃₃ = 170 pC/N and the dielectric constant ?_r = 1900 (at a frequency of 1 kHz) are obtained at x = 0.3.     

Structural, magnetic and electrical properties of Bi1.4La0.6Sr2CaCu2−xMnxOy compounds

The Mn-doped compounds Bi_1.4La_0.6Sr₂CaCu₂O_y were prepared by sol-gel method. The structural variation was characterized systematically by X-ray diffraction (XRD), infrared (IR) spectra and Raman scattering spectra, respectively. The electrical and magnetic properties of the compounds were investigated by the temperature dependence of resistivity (R-T) and magnetic hysteresis loop (M (H)) measurements. Results indicate that the subtle change of lattice parameters has taken place in the compounds, which is attributed to CuO₂ planes canting and Mn valence alternation. In the condition of preserving Bi-2212 structure, Bi_1.4La_0.6Sr₂CaCu_2−xMn_xO_y compound has optimal resistivity and magnetism at x = 2%, which could provide a candidate as new barrier in Josephson junction in future.     

Dielectric and piezoelectric properties of Sb doped (NaBi)0.38(LiCe)0.05[]0.14Bi2Nb2O9 ceramics

Sb⁵⁺-doped (NaBi)_0.38(LiCe)_0.05[]_0.14Bi₂Nb₂O₉ (represented as NBNLCS-x, where [] represents A-site vacancies) ceramics were prepared by the conventional solid-state route. The ceramics well sintered to approach ∼98.5% theoretical density and the tetragonality of crystal structure increased with Sb⁵⁺ additions. However, the Curie temperature (T_C) and the piezoelectric coefficient (d₃₃) of Sb⁵⁺-modified ceramics gradually decreased. The 3 mol% Sb⁵⁺-doped samples exhibited optimum properties with a d₃₃ value of ∼22 pC/N planar electromechanical coupling factor (k_p) of ∼11.2% and relatively high T_C of ∼765 °C. These results indicate that NBNLCS-x material is a promising candidate for high-temperature piezoelectric applications.     

Phase structure and electrical properties of (0.8 − x) BaTiO3-0.2Bi0.5Na0.5TiO3-xBaZrO3 lead-free piezoceramics

Lead-free piezoelectric ceramics (0.8 − x)BaTiO₃-0.2Bi_0.5Na_0.5TiO₃-xBaZrO₃ (BT-BNT-xBZ, 0 ≤ x ≤ 0.08) doped with 0.3 wt% Li₂CO₃ were prepared by conventional solid-state reaction method. With the Li₂CO₃ doping, all the ceramics can be well sintered at 1170-1210 °C. The phase structure, dielectric, ferroelectric and piezoelectric properties of the ceramics were investigated. Results show that a morphotropic phase boundary (MPB) between tetragonal and pseudocubic phases exists at x = 0.03-0.04. The addition of Zr can improve the piezoelectric properties of BT-BNT ceramics. Furthermore, a relaxor behavior is induced and the tetragonal-cubic phase transition shifts towards lower temperatures after the addition of Zr. The ceramics with x = 0.03 possess the optimum electrical properties: d₃₃ = 72 pC/N, k_p = 15.4%, ?_r = 661, P_r = 18.5 μC/cm², E_c = 34.1 kV/cm, T_c = 150 °C.     

Microwave dielectric properties of temperature stable Li2ZnxCo1−xTi3O8 ceramics

The Li₂Zn_xCo_1−xTi₃O₈ (x = 0.2-0.8) solid solution system has been synthesized by the conventional solid-state ceramic route and the effect of Zn substitution for Co on microwave dielectric properties of Li₂CoTi₃O₈ ceramics has also been investigated. The microwave dielectric properties of these ceramics show a linear variation between the end members for all compositions. The optimized sintering temperatures of Li₂Zn_xCo_1−xTi₃O₈ ceramics increase with increasing content of Zn. The specimen with x = 0.4 sintered at 1050 °C/2 h exhibits an excellent combination of microwave dielectric properties with ?_r = 27.7, Q_u × f = 57,100 GHz and τ_f = −1.0 ppm/°C.     

Polymorphic phase transition-induced electrical behavior of BiCoO3-modified (K0.48Na0.52)NbO3 lead-free piezoelectric ceramics

(1 − x)(K_0.48Na_0.52)NbO₃-xBiCoO₃ [KNN-xBC] lead-free piezoelectric ceramics were prepared by the conventional solid-state sintering method. The effects of the BiCoO₃ addition on the phase structure, dielectric, piezoelectric and ferroelectric properties of KNN-xBC ceramics were systematically investigated. The polymorphic phase transition (PPT) from rhombohedral to orthorhombic phase around room temperature was identified in the composition range of 0.01 ≤ x ≤ 0.02, and the improved electrical properties were induced by this PPT. The KNN-0.01BC ceramics near PPT exhibit optimum electrical properties: d₃₃ ∼ 165 pC/N, k_p ∼ 0.40, P_r ∼ 31.0 μC/cm², and E_c ∼ 12.6 kV/cm. These results indicate that the enhanced piezoelectric properties for alkali niobate can be achieved by forming the coexistence of rhombohedral and orthorhombic phases.     

Effect of CuO on the sintering temperature and piezoelectric properties of MnO2-doped 0.75Pb(Zr0.47Ti0.53)O3-0.25Pb(Zn1/3Nb2/3)O3 ceramics

The sintering temperature of 0.75Pb(Zr_0.47Ti_0.53)O₃-0.25Pb(Zn_1/3Nb_2/3)O₃ ceramics containing 1.5 mol% MnO₂ was decreased from 930 to 850 °C with the addition of CuO. The CuO reacted with the PbO and formed a liquid phase during the sintering, which assisted the densification of the specimens. Most of the Cu²⁺ ions existed in the CuO second phase, thereby preventing any possible hardening effect from the Cu²⁺ ions. Variations of the k_p, Q_m, ?₃^T/?₀ and d₃₃ values with CuO were similar to that of the relative density. The specimen containing 0.5 mol% CuO sintered at 850 °C showed the good piezoelectric properties of k_p = 0.5, Q_m = 1000, ?₃^T/?₀ = 1750 and d₃₃ = 300 pC/N.     

Room temperature electroresistance in Sr2−xGdxMnTiO6 perovskites (0 ≤ x ≤ 1)

We report on the room temperature strong (∼80%) electroresistance (ER) in the double perovskite with mixed Mn valence: Sr_2−xGd_xMnTiO₆, 0 ≤ x ≤ 1. Both, continuous and pulsed current-voltage curves are almost identical which indicates that the observed electroresistance is not associated with heating. This is also supported by simultaneous temperature measurements. ER is negligible (absent) in the x = 0 compound and increases with the increase of Gd content ‘x’. The amplitude of ER has a maximum for x = 0.75, suggesting that ER is determined by both the double exchange and the Mn³⁺ concentration. At the same time, magnetic interactions change from the antiferromagnetic (x = 0) to ferromagnetic ones as x → 1, thus linking the ER with ferromagnetism.     

Phase transition and piezoelectric properties of K0.48Na0.52NbO3-LiTa0.5Nb0.5O3-NaNbO3 lead-free ceramics

Plate-like NaNbO₃ (NN) particles were used as the raw material to fabricate (1 − x)[0.93 K_0.48Na_0.52Nb O₃-0.07Li(Ta_0.5Nb_0.5)O₃]-xNaNbO₃ lead-free piezoelectric ceramics using a conventional ceramic process. The effects of NN on the crystal structure and piezoelectric properties of the ceramics were investigated. The results of X-ray diffraction suggest that the perovskite phase coexists with the K₃Li₂Nb₅O₁₅ phase, and the tilting of the oxygen octahedron is probably responsible for the evolution of the tungsten-bronze-typed K₃Li₂Nb₅O₁₅ phase. The Curie temperature (T_C) is shifted to lower temperature with increasing NN content. (1 − x)[0.93 K_0.48Na_0.52NbO₃-0.07Li(Ta_0.5Nb_0.5)O₃]-xNaNbO₃ ceramics show obvious dielectric relaxor characteristics for x > 0.03, and the relaxor behavior of ceramics is strengthened by increasing NN content. Both the electromechanical coupling factor (k_p) and the piezoelectric constant (d₃₃) decrease with increasing amounts of NN. 0.01-0.03 mol of plate-like NaNbO₃ in 0.93 K_0.48Na_0.52NbO₃-0.07Li(Ta_0.5Nb_0.5)O₃ gives the optimum content for preparing textured ceramics by the RTGG method.     

Structural, optical and electromagnetic properties of Bi1−xHoxFeO3 multiferroic materials

Bi_1−xHo_xFeO₃ (x = 0.00, 0.05, 0.10, 0.15 and 0.20) polycrystalline ceramics were synthesized by a solid-state reaction and their structural, absorption, Raman scattering, impedance and magnetic properties were investigated. The substitution of rare earth Ho for Bi was found to decrease the impurity phase in BiFeO₃ ceramics. There appears an anomalous change in the lattice constants, optical band gap as well as the impedance spectroscopy and magnetization of samples at x = 0.10, suggesting a limit of dissolubility of Ho doped ions in BiFeO₃. Additionally, the Raman measurement performed for the lattice dynamics study of Bi_1−xHo_xFeO₃ samples reveals a band centered at around 1000-1300 cm⁻¹ which is associated with the resonant enhancement of two-phonon Raman scattering in the multiferroic Bi_1−xHo_xFeO₃ samples. Ho-doped BiFeO₃ also showed a ferromagnetic-like behavior with M_r = 1070 × 10⁻⁴ and M_s = 1.60 emu/g for optimum content x = 0.10, which is similar to the solid solution system of BiFeO₃.     

Luminescent properties of Na3Gd1−xEux(PO4)2 and energy transfer in these phosphors

A series of Eu³⁺ activated Na₃Gd_1−xEu_x(PO₄)₂ (0 ≤ x ≤ 1) phosphors were synthesized by solid-state reaction method. The structures and photo-luminescent properties of these phosphors were investigated at room temperature. The results of XRD patterns indicate that these phosphors are isotypic to the orthorhombic Na₃Gd(PO₄)₂. The excitation spectra indicate that these phosphors can be effectively excited by near UV (370-410 nm) light. The intensities of magnetic dipole transition ⁵D₀ → ⁷F₁ and forced electric dipole transition ⁵D₀ → ⁷F₂ are comparable, and the energy ratio (⁵D₀ → ⁷F₁/⁵D₀ → ⁷F₂) is 1.1. The emission spectra exhibit strong reddish orange performance (CIE chromaticity coordinates: x = 0.62, y = 0.38), which is due to the ⁵D₀ → ⁷F_J transitions of Eu³⁺ ions. The correlation between the structure and the photo-luminescent properties of the phosphors was studied. The energy transfer and concentration quenching of the phosphors were discussed. Na₃Gd_1−xEu_x(PO₄)₂ has a potential application for white light-emitting diodes.     

Calculation of band offsets in Cd1−xXxTe alloys, X = Zn, Mg, Hg and Mn and magnetic effects in CdMnTe

Due to the large variety of properties offered by the telluride binaries CdTe, ZnTe, MgTe, HgTe and MnTe as well as their mixed ternary alloys, an accurate knowledge of their electronic band parameters is crucial. These materials have been extensively studied but, some points bearing on several properties have never previously reported or are still not clear. In this paper, we report results on the conduction and valence band offsets of the pseudo-morphically strained Cd_1−xX_xTe layer on relaxed Cd_1−yX_yTe substrate, X = Zn, Hg, Mg and Mn. Based on the Van Der Walle model, calculations have been performed for the all range of material and substrate 0 ≤ x,y ≤ 1. These discontinuities have not yet calculated for X = Mg, Mn or Hg in the all range 0 ≤ x,y ≤ 1. For the CdMnTe diluted magnetic semiconductor which we focus more interest due to its considerable current interest for applications, calculations have been done without and with correction taking into account magnetic effect of magnesium ions Mn²⁺. It is found that the introduction of only a few percent of Mn into CdTe provides a unique opportunity to combine two important fields in physics, semiconductivity and magnetism. We can take advantage both of possibility of applications in solid-state lasers and exceptional magnetic properties offered by this magnetic diluted semiconductor.This study presents important quantities that are required to model quantum structures and offers a fast and inexpensive way to check device designs and processes.     

Synthesis and functional properties of the Ni1−xMnxFe2O4 ferrites

Nanocrystalline Ni_1−xMn_xFe₂O₄ (x = 0; 0.17; 0.34; 0.5) ferrite powders were successfully synthesized using the sol-gel combustion method, by using nitrates as cations source and citric acid (C₆H₈O₇) as combustion/chelating agent. The reaction advancement was observed by means of IR absorption spectroscopy, by monitoring two characteristic bands for the spinel compounds at about 600 cm⁻¹ and 400 cm⁻¹, respectively. The as-synthesized powders were characterized by IR spectroscopy, X-ray diffraction (XRD) and scanning electronic microscopy (SEM). The magnetic study shows that the saturation magnetization decreases with increasing the Mn addition, as result of the particle size reduction. The dielectric properties were measured as a function of frequency in the range of 10 Hz to 1 MHz. The real part of permittivity has values of ∼88 at 1 kHz and ∼7 at 1 Hz for x = 0. An increasing dielectric permittivity with increasing the amount of Mn is observed. For all the investigated compositions, both the real and imaginary parts of permittivity decrease with frequency.     

Improving the piezoelectric thermal stability by tailoring phase transition behavior in the new (1 − x)[0.65PbMg1/3Nb2/3O3-0.35PbTiO3]-xBiZn1/2Ti1/2O3 perovskite solid solutions

The phase transition behavior and its effect on thermal stability of the piezoelectric properties of the (1 − x)[0.65PbMg_1/3Nb_2/3O₃-0.35PbTiO₃]-xBiZn_1/2Ti_1/2O₃ ceramics with 0 ≤ x ≤ 0.06 were investigated. The phase transition from the monoclinic to tetragonal phase was determined by the dielectric constant and elastic constant measurements. The temperature independent piezoelectric response with −d₃₁ = 188 pC/N was obtained from 175 to 337 K for the composition with x = 0.02. The enhanced thermal stability of piezoelectric response was achieved by shifting the monoclinic-tetragonal phase transition to the lower temperature.     

Growth and characterization of perovskite LaGaO3 crystals doped with Sr and Mn

Single crystals of LaGaO₃ doped with Sr and Mn (LSGMn) were grown by the Czochralski method from the melt with compositions: La_1−xSr_xGa_1−yMn_yO₃, x = y = 0.02; 0.05 and x = 0.05, y = 0.06. Single crystals with 20 mm diameter with convex crystal-melt interface were grown on LaGaO₃ oriented seed with pulling rate of 2 mm/h. Single crystals were dark and have strong tendency to spiral growth. This tendency was decreased with increasing the Mn content in comparison with Sr. Effective segregation coefficients for Sr and Mn in LaGaO₃ are lower than 1. Room-temperature structural measurements by X-ray powder diffraction showed perovskite structure with Pbnm space group for all measured samples. Orthorhombic b and c lattice parameters decrease, whereas a slightly increases with decreasing orthorhombic unit cell volume that is related to increased amount of Mn and Sr in the melt. Thermal analysis and Raman investigations showed that the temperature of the first order phase transitions temperature form orthorhombic to rhombohedral structure observed in pure LaGaO₃ at about 150 °C decreases to about 49 °C at the bottom part of crystal with x = y = 0.05 composition.     

High temperature thermoelectric properties and energy transfer devices of Ca3Co4−xAgxO9 and Ca1−ySmyMnO3

The high temperature oxide thermoelectric materials of p-type Ca₃Co_4−xAg_xO₉ (denoted as p-Co349/Ag_x) and n-type Ca_1−ySm_yMnO₃ (denoted as n-Mn113/Sm_y) were prepared by the self-ignition method combined with a sintering technique. The influence of doping Ag and Sm on the thermoelectric properties of the corresponding materials was evaluated. The figures of merit, ZT, for the p-Co349/Ag_0.2 and n-Mn113/Sm_0.02 materials reached maxima of 0.20 and 0.15 at 973 K, respectively. The performances of thermoelectric devices constructed with the p- and n-type pairs were evaluated in terms of the maximum output power (P_max) and manufacturing factor. The P_max and volume power density for the four-leg devices reached 36.8 mW and 81.9 mW cm⁻³ at ΔT of 523 K, respectively.