Effects of ABS‐g‐MAH on mechanical properties and compatibility of ABS/PC alloy

The effects of a compatibilizer, namely, an acrylonitrile–butadiene–styrene copolymer (ABS) grafted with maleic anhydrade (MAH) (ABS‐g‐MAH), on the mechanical properties and morphology of an ABS/polycarbonate (PC) alloy were studied The results showed that a small quantity of ABS‐g‐MAH has a very good influence on the notched Izod impact strength of the ABS/PC alloy without compromising other properties such as the tensile strength, flexural strength, and Vicat softening temperature (VST). The impact strength of the ABS/PC alloy, to a great extent, depends on the loading of ABS‐g‐MAH and the degree of grafting (DG) of MAH in the ABS‐g‐MAH. DSC analysis and SEM observation confirmed that ABS‐g‐MAH could significantly improve the compatibility of the ABS/PC alloy. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 831–836, 2001     

Influence of rubber content in ABS in wide range on the mechanical properties and morphology of PC/ABS blends with different composition

A series of acrylonitrile–butadiene–styrene (ABS) with different rubber content were prepared by diluting ABS grafting copolymer containing 60% rubber with a styrene–acrylonitrile copolymer. ABS prepared were blended with bisphenol‐A‐polycarbonate (PC) at the ratio of 70/30, 50/50, and 30/70 to prepare PC/ABS blends. Influence of rubber content in ABS on the properties of ABS and PC/ABS blends were investigated. PC/ABS blends with different compositions got good toughness when the rubber in ABS increased to the level that ABS itself got good toughness. The tensile properties and processability of PC/ABS blends decreased with the increase of the total rubber content introduced into the blends. ABS with the rubber content of 30 wt% is most suitable to be used to prepare PC/ABS blends. The rubber content in ABS affected the viscosity of ABS, and subsequently the viscosity ratio of PC to ABS. As a result, the morphology of PC/ABS blends varied. The increase of rubber content in ABS results in finer structure of PC/ABS blends. POLYM. ENG. SCI. 46:1476–1484, 2006. © 2006 Society of Plastics Engineers.     

Melt processing,mechanical, and fatigue crack propagation properties of reactively compatibilized blends of polyamide 6 and acrylonitrile–butadiene–styrene copolymer

Within a IUPAC study, melt processing, mechanical, and fatigue crack growth properties of blends of polyamide 6 (PA 6) and poly(acrylonitrile–butadiene–styrene) (ABS) were investigated. We focused on the influence of reactive compatibilization on blend properties using a styrene–acrylonitrile–maleic anhydride random terpolymer (SANMA). Two series of PA 6/ABS blends with 30 wt % PA 6 and 70 wt % PA 6, respectively, were prepared with varying amounts of SANMA. Our experiments revealed that the morphology of the matrix (PA 6 or ABS) strongly affects the blend properties. The viscosity of PA 6/ABS blends monotonically increases with SANMA concentration because of the formation of high‐molecular weight graft copolymers. The extrudate swell of the blends was much larger than that of neat PA 6 and ABS and decreased with increasing SANMA concentrations at a constant extrusion pressure. This observation can be explained by the effect of the capillary number. The fracture resistance of these blends, including specific work to break and impact strength, is lower than that of PA 6 or ABS alone, but increases with SANMA concentration. This effect is most strongly pronounced for blends with 70 wt % PA 6. Fatigue crack growth experiments showed that the addition of 1–2 wt % SANMA enhances the resistance against crack propagation for ABS‐based blends. The correlation between blend composition, morphology and processing/end‐use properties of reactively compatibilized PA 6/ABS blends is discussed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of ABS type on morphology and mechanical properties of PC/ABS blends

The morphology and the mechanical properties of polycarbonate (PC) blends with different acrylonitrile–butadiene–styrene (ABS) materials were investigated. PC/ABS blends based on a mass-made ABS with 16% rubber and large (0.5–1μm) rubber particles are compared to blends based on an emulsion-made ABS with 50% rubber and small, monodisperse (0.12 μm) rubber particles over the full range of blend compositions. The blends with the bulk ABS showed excellent impact strength for most compositions, and those containing 50 and 70% PC exhibited ductile to brittle transition temperatures below that of PC. The blends with the emulsion ABS showed excellent toughness in sharp notch Izod impact tests at room temperature and in standard notch Izod impact tests at low temperatures near the T_g of the rubber. By melt blending the various ABS materials with a styrene–acrylonitrile (SAN 25) copolymer, materials with lower rubber concentrations were obtained. These materials were used in blends with PC to make comparisons at constant rubber concentration of 5, 10, and 15%. The results of this investigation show that brittle ABS materials can produce tough PC–ABS blends. It is apparent that small rubber particles toughen PC–ABS blends at lower rubber concentrations and at lower temperatures than is possible with large rubber particles. However, additional work is needed to understand the nature of toughening in these PC–ABS blends with different rubber phase morphologies. It is of particular interest to understand the exceptional ductility of some of the blends at low temperatures. © 1994 John Wiley & Sons, Inc.     

Influence of mixing time during glycine–nitrate process on the structural properties and reducibility of a dual-phase Ni–Cu–Mn spinel catalyst

The potential of Ni–Cu–Mn spinels as methane reforming catalysts for hydrocarbon-fueled solid oxide fuel cell (SOFC) applications is highly dependent on its catalytic properties, particularly reducibility. The reducibility of a spinel-structured catalyst is often correlated with its structural properties and fabrication processes. In this work, the structural properties and reducibility of a Ni–Cu–Mn spinel catalyst was evaluated on the basis of mixing time during the glycine–nitrate process. Phase analysis results showed that Ni_0.4Cu_0.6Mn_2.0O₄ and (Cu, Mn)₃O₄ in normal or inversed spinel structures were observed in GNP-produced Ni–Cu–Mn spinel catalyst powders. Distortion in inverse spinel structures enhanced the reducibility of the spinel catalyst. Morphological analysis results showed that complete nitrate binding occurred at a minimum mixing time of 24 h and resulted in homogenous particle size distribution and uniform elemental distribution. Furthermore, the Ni–Cu–Mn spinel catalyst produced after 24 h of mixing was fully reduced at 450 °C. The reducing pattern of the Ni–Cu–Mn spinel catalyst produced after 24 h of mixing time showed strong metal–support interaction and the fast adsorption of reactants. These effects were due to either the distribution of divalent cations in octahedral sites or large amounts of bulk pores. In conclusion, a minimum mixing time of 24 h is sufficient to produce the desired structural properties and reducibility of Ni–Cu–Mn spinel catalysts for SOFC applications.     

Flammability and thermal stability studies of ABS/Montmorillonite nanocomposite

Acrylonitrile–butadiene–styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X‐ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated–delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated–intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry     

Recycled polycarbonate/acrylonitrile–butadiene–styrene reinforced and toughened through chemical compatibilization

To improve the utilization efficiency of recycled polycarbonate/acrylonitrile–butadiene–styrene (R-PC/ABS), we studied the mechanical, morphological, and rheological properties of R-PC/ABS with styrene–butadiene–glycidyl methacrylate (SBG), which was used to reinforce and toughen the R-PC/ABS through chemical compatibilization. Fourier transform infrared spectroscopy demonstrated that carboxyl and hydroxyl groups in R-PC/ABS reacted with epoxy groups in SBG to produce ester and ether groups. The results of scanning electron microscopy show that the domain sizes of the ABS particles decreased when the SBG content was 6 wt %; this demonstrated that the compatibility of the polycarbonate (PC) and ABS was improved after the addition of SBG. The results of the loss modulus of dynamic mechanical analysis were consistent with the morphological results, which reflected a better compatibility of PC and ABS in the modified samples. The introduction of SBG increased the molecular weight and entanglements; this improved the viscosity and storage modulus in the modified samples, as demonstrated by the rheological results. Furthermore, the mechanical properties were obviously enhanced, especially the impact strength, when the SBG content was 6 wt %; this was ascribed to the chemical reactions and improved compatibility after melt extrusion with SBG. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47537.     

Functionalized Hybrid Coatings on ABS Surfaces by PLD and Dip Coatings

It is important to give water-repellent and antibacterial properties to the acrylonitrile butadiene styrene (ABS) surfaces of the hearing aids. In this study, the sol–gel Si and sol–gel Ti solutions were prepared from the reactions of silicon ethoxide, titanium butoxide and methacrylic acid. The catalyst and Dynasylan F8815 were added to the sol–gel solutions to give hydrophobic properties onto the ABS surfaces. Additionally, silver nanoparticles were synthesized by nanosecond laser and added to the coating solutions to give extra antibacterial properties. The surfaces of the ABS targets were coated using the sol–gel dip coating and pulsed laser deposition techniques. The coatings with good adhesion between film and substrate and good water-repellent properties were achieved. The average contact angles for the coated ABS surfaces were measured in the range between 120 and 125 degrees. The obtained sol–gel materials and produced thin films onto the ABS surfaces were also analyzed in terms of the antibacterial properties. The highly antibacterial properties were observed in the sol–gel solutions and the thin films.     

Compatibility and thermal properties of poly(acrylonitrile–butadiene–styrene) copolymer blends with poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile)

The mechanical and heat‐resistant properties of acrylonitrile–butadiene–styrene (ABS) binary and ternary blends were investigated. The relationship of compatibility and properties was discussed. The results show that poly(methyl methacrylate) (PMMA) and styrene–maleic anhydride (SMA) can improve the thermal properties of conventional ABS. The Izod impact property of ABS/PMMA blends increases significantly with the addition of PMMA, whereas that of ABS/SMA blends decreases significantly with the addition of SMA. Blends mixed with high‐viscosity PMMA are characterized by higher heat‐distortion temperature (HDT), and their heat resistance is similar to that of blends mixed with SMA. For high‐viscosity PMMA, from 10 to 20%, it is clear that blends appear at the brittle–ductile transition, which is related to the compatibility of the two phases. TEM micrographs show low‐content and high‐viscosity PMMA in large, abnormally shaped forms in the matrix. Compatibility between PMMA and ABS is dependent on both the amount and the viscosity of PMMA. When the amount of high‐viscosity PMMA varied from 10 to 20 wt %, the morphology of the ABS binary blends varied from poor to satisfactory compatibility. As the viscosity of PMMA decreases, the critical amount of PMMA needed for the compatibility of the two phases also decreases. SMA, as a compatibilizer, improved the interfacial adhesiveness of ABS and PMMA, which results in PMMA having good dispersion in the matrix. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2652–2660, 2002     

The influence of viscosity and composition of ABS on the ABS/SBS blend morphology and properties

Acrylonitrile–butadiene–styrene (ABS) shows excellent impact resistance and good stiffness. The incorporation of thermoplastic elastomer into ABS may consist in an interesting approach to further improve the toughness of ABS, in addition to tuning its compatibility with reinforcements. Blends of ABS and styrene–butadiene–styrene (SBS) were obtained by extrusion from different types of ABS with different SBS contents. The results showed that morphology and mechanical behavior of ABS/SBS blends depend strongly on the composition and characteristics of ABS matrix. An increase in elongation at break and slight decrease in modulus could be observed by increasing SBS content. ABS/SBS blend possessing good dispersion of rubber particles with sizes ranging from 0.1 to 0.8 μm of rubber particles exhibited the better performance of the impact resistance, whereas blends showing a predominance of relatively large particles resulted on poorer mechanical properties. These results suggest that viscosity and composition of ABS matrix play a significant role on the dispersion and coalescence of the dispersed phase during mixing. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47075.     

Enhancement of char‐forming and water resistance on ABS modified by poly(4‐nitrophenoxy)‐phosphazene

Poly(4‐nitrophenoxy)‐phosphazene (DPP) was used as charring and water resistance agent in Acrylonitrile–butadiene–styrene (ABS) composites. The char‐forming capability of DPP and combustion behavior of DPP‐based ABS (ABS‐DPP) were studied by thermogravimetric analysis (TGA) and cone calorimeter, respectively. TGA‐coupled Fourier transform infrared (TGA/FTIR) was used to research the releasing intensity of gaseous products during decomposition. Moreover, the char formation morphology of ABS, DPP, and ABS‐DPP were observed by scanning electron microscopy analysis. The water resistance of DPP was measured by the boiled water tests, the FTIR and static water contact angle analysis. The flame properties of samples and the samples treated by boiled water were studied by LOI and UL‐94, and the tensile properties of ABS‐DPP samples were assessed by tensile testing at high temperature. The results showed that the residues yield of ABS‐DPP samples increased from 0 to more than 20% under nitrogen and from 0.7 to 3.9% under air compared with pure ABS. The combustibility of ABS was decreased by DPP; however, the water resistance of ABS was not affected. At high temperature, tensile strength of ABS‐DPP decreased and the elongation at break enhanced with the addition of DPP. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45988.     

The effect of recycling number on the mechanical,chemical, thermal,and rheological properties of PBT/PC/ABS ternary blends: With and without glass‐fiber

The recycling possibilities of poly(butylene terephthalate)/polycarbonate/acrylonitrile–butadiene–styrene (PBT/PC/ABS) ternary blend with and without glass‐fiber content were investigated using repeated injection molding process. In this study, PBT/PC/ABS ternary blends were reprocessed at five times and the results were presented after each recycling process. The recycling possibility of PBT/PC/ABS ternary blend was evaluated by measuring the mechanical, chemical, thermal, and rheological properties. Mechanical properties were determined by the tensile strength, yield strength, strain at break, elastic modulus, impact strength, flexural strength, and flexural modulus. Chemical and thermal properties were evaluated by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermal gravimetric analysis, and scanning electron microscopy. Rheological properties of the ternary blends were studied by melt flow index measurement. From the results, it was found that mechanical properties of recycled composites were better than virgin PBT/PC/ABS ternary blends. POLYM. COMPOS., 35:2074–2084, 2014. © 2014 Society of Plastics Engineers     

Morphological and mechanical properties of PP/ABS blends compatibilized with PP‐g‐acrylic acid

Polypropylene (PP) and acrylonitrile–butadiene–styrene (ABS) blends were prepared by a melt extrusion process. PP‐g‐acrylic acid was used as a compatibilizer. Blends with various compositions of PP, compatibilizer, and ABS were prepared and studied for morphological and mechanical properties. PP‐rich ternary blends showed good morphological and mechanical properties. The use of 5 wt % PP‐g‐acrylic acid as a compatibilizer resulted in a fine and homogeneous dispersion of the ABS phase in the PP phase. The experimental data of the tensile modulus showed good agreement in PP‐rich compositions with that generated from Kerner's model with perfect adhesion. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1731–1741, 2001     

Recycling of acrylonitrile–butadiene–styrene and high‐impact polystyrene from waste computer equipment

Acrylonitrile–butadiene–styrene (ABS) and high‐impact polystyrene (HIPS) are two of the plastics most frequently used as outer casings for computer equipment such as monitors, keyboards, and other similar components. We assessed the effects of the recycling and blending of ABS and HIPS on mechanical properties. We found that the effects of recycling on ABS and HIPS were similar, in that changes in glass‐transition temperatures, tensile strengths, and tensile moduli were negligible, but strains to failure and impact strengths were reduced considerably. Blending proportions of ABS and HIPS caused no more deterioration in properties than occurred as a result of the recycling process, and the presence of small proportions of one material in the other actually restored significant amounts of ductility, as seen by increases in the strains to failure. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 572–578, 2002     

Effect of carbon black and nanoclay on mechanical and thermal properties of ABS–PANI/ABS–PPy blends

Acrylonitrile butadiene styrene (ABS)–polyaniline (PANI) and ABS–polypyrrole (PPy) blends exhibit poor mechanical and thermal properties due to their weak interfacial adhesion and inhomogeneous mixing. The properties have been improved by addition of carbon black (CB) and nanoclay (NC). Composites are prepared by mixing CB and NC with ABS–PANI and ABS–PPY blends. The morphology and crystalline characteristics are studied using field emission scanning electron spectroscopy (FESEM) and X‐ray diffraction, respectively. In addition, all the composites have been analyzed for their mechanical and thermal performance. The tensile strength of ABS–PANI has been increased by 7.18% and 65.83% with addition of CB and a combination of CB–NC, respectively. FESEM images are found supportive with these trends and show homogeneous dispersion of CB in the polymer matrix, assisted by NC. Dynamic mechanical analysis results also show slight improvement of glass transition temperature (T_g) with addition of fillers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42577.     

Blends of bisphenol A polycarbonate and rubber‐toughened styrene–maleic anhydride copolymers

The morphology and mechanical properties of polycarbonate (PC) blends with rubber‐toughened styrene–maleic anhydride copolymer materials (TSMA) were investigated and compared with the properties of blends of PC with acrylonitrile–butadiene–styrene (ABS) materials. The PC/TSMA blends showed similar composition dependence of properties as the comparable PC/ABS blends. Polycarbonate blends with TSMA exhibited higher notched Izod impact toughness than pure PC under sharp‐notched conditions but the improvements are somewhat less than observed for similar blends with ABS. Since PC is known for its impact toughness except under sharp‐notched conditions, this represents a significant advantage of the rubber‐modified blends. PC blends with styrene–maleic anhydride copolymer (SMA) were compared to those with a styrene–acrylonitrile copolymer (SAN). The trends in blend morphology and mechanical properties were found to be qualitatively similar for the two types of copolymers. PC/SMA blends are nearly transparent or slightly pearlescent. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1508–1515, 1999     

Dynamically vulcanized acrylonitrile–butadiene–styrene terpolymer/nitrile butadiene rubber blends compatibilized by chlorinated polyethylene

Thermoplastic vulcanizates (TPVs) based on acrylonitrile–butadiene–styrene (ABS)/nitrile butadiene rubber (NBR) blends were prepared by dynamic vulcanization and then compatibilized by chlorinated polyethylene (CM). The effects of CM compatibilizer on the mechanical properties, Mullins effect, and morphological and dynamic mechanical properties of the TPVs were investigated systematically. Experimental results indicated that CM had an excellent compatibilization effect on the dynamically vulcanized ABS/NBR TPVs. Mullins effect results showed that the compatibilized ABS/NBR TPV had relatively lower internal friction loss than the ABS/NBR TPV, indicating the improvement of elasticity. Morphology studies showed that the fracture surfaces of ABS/CM/NBR TPVs were relatively smoother, indicating the improved elastic reversibility. DMA studies showed that the glass to rubber transition temperatures of ABS and NBR phases were slightly shifted toward each other with the incorporation of CM compatibilizer, which indicates the improvement of the compatibility. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40986.     

Impact behavior and fracture morphology of acrylonitrile–butadiene–styrene resins toughened by linear random styrene–isoprene–butadiene rubber

A novel toughening modifier, styrene–isoprene–butadiene rubber (SIBR), was used to improve the impact resistance and toughness of acrylonitrile–butadiene–styrene (ABS) resin via bulk polymerization. For comparison, two kinds of ABS samples were prepared: ABS‐1 was toughened by a conventional modifier (a low‐cis polybutadiene rubber/styrene–butadiene block copolymer), and ABS‐2 was toughened by SIBR. The mechanical properties, microstructures of the as‐prepared materials, and fracture surface morphology of the specimens after impact were studied by instrumented notched Izod impact tests and tensile tests, transmission electron microscopy, and scanning electron microscopy, respectively. The mechanical test results show that ABS‐2 had a much higher impact strength and elongation at break than ABS‐1. The microscopic results suggested that fracture resistance of ABS‐1 only depended on voids, shear yielding, and few crazing, which resulted in less ductile fracture behavior. Compared with ABS‐1, ABS toughened by linear random SIBR (ABS‐2) displayed the synergistic toughening effect of crazing and shear yielding, which could absorb and dissipate massive energy, and presented high ductile fracture behavior. These results were also confirmed by instrumented impact tests. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical properties of acrylonitrile–butadiene–styrene copolymer/poly(l‐lactic acid) blends and their composites

As the material properties of acrylonitrile–butadiene–styrene copolymer (ABS) have an excessively wide margin for applications in automobile console boxes, ABS partly replaced with poly(l ‐lactic acid) (PLA) may be used for the same purpose with improved ecofriendliness if the corresponding deterioration of the material properties is acceptable through the choice of appropriate additives. ABS composites with 30 wt % renewable components (PLA and cellulose pulp) were prepared by melt compounding, and the material properties were examined as a function of the additive content. The changes in the mechanical properties of the ABS/PLA blends were examined after the addition of cellulose pulp and two clays [Cloisite 25A (C25A) and sodium montmorillonite] as well as these two clays treated with bis(3‐triethoxysilylpropyl)tetrasulfide (TESPT). The heat distortion temperatures of the composites were measured as a function of the content of the TESPT‐treated C25A. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40329.     

Morphology,thermal, and mechanical properties of acrylonitrile–butadiene–styrene/carbon black composites

Acrylonitrile–butadiene–styrene (ABS) polymers are susceptible to degradation that increases the yellowness of the polymer, distorts the surface glossy, and affects the mechanical properties. One way to protect ABS against degradation is the addition of carbon black (CB) that can act as a stabilizer. In this work, CB was dispersed in ABS through melt‐compounding. Electron microscopy was used to study the morphology of the filled‐ and unfilled‐ABS, and revealed that the CB particles/aggregates were distributed within the styrene–acrylonitrile (SAN) phase and around the PB phase. The results of the Fourier transform infrared spectroscopy showed that upon processing of ABS, crosslinking in the polybutadiene (PB) phase was the governing degradation mechanism. Increasing the CB content resulted in increasing the heat stability of the ABS/CB compounds, which was confirmed by thermogravimetric analysis. The DTA results showed that the PB degradation peak occurring at about 395°C was disappeared by addition of CB. Impact strength test was performed to study the effect of CB on the toughness of ABS. Impact strength was reduced with increasing CB loading. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007