Strengthening of Masonry Arches with Fiber-Reinforced Polymer Strips

This paper deals with masonry arches and vaults strengthened with surface fiber-reinforced polymer (FRP) reinforcement in the form of strips bonded at the extrados and/or intrados, considering strip arrangements that prevent hinged mode failure, so the possible failure modes are: (1) crushing, (2) sliding, (3) debonding, and (4) FRP rupture. Mathematical models are presented for predicting the ultimate load associated with each of such failure modes. This study has shown that the reinforced arch is particularly susceptible to failure by crushing, as a result of an ultimate compressive force being collected by a small fraction of the cross section. Failure by debonding at the intrados may also be an issue, especially in the case of weak masonry blocks or multiring brickwork arches. Failure by sliding has to be considered if the reinforcement is at the extrados and loading is considerably nonsymmetric.     

Analytical Investigation of Lateral Strength of Masonry Infilled RC Frames Retrofitted with CFRP

In this study, two reinforced concrete frames with hollow clay tile masonry infill walls, retrofitted with diagonally applied carbon fiber-reinforced polymer (CFRP), which were tested previously, were analytically investigated. A simple material model for the masonry infill wall strengthened with CFRP is suggested. The lateral strength of each rehabilitated frame was obtained by pushover analysis of four different models using a commercially available finite-element program, and the results were compared with the test results. We also determined the lateral strength of the CFRP-applied masonry infill walls, and compared the results with the results obtained from existing analytical models. Drift capacity of the masonry infill walls strengthened with CFRP was also investigated, and the drift capacity of the masonry infill walls strengthened with diagonally applied CFRP was recommended. It is concluded that the strength of the masonry infilled frames strengthened with diagonally applied CFRP can be satisfactorily predicted with the suggested procedure. The ultimate drift capacity of the masonry infill walls strengthened with diagonally applied CFRP strips was conservatively predicted to be 1.0%.     

Strengthening of Brick Masonry Arches with Externally Bonded Steel Reinforced Composites

The objective of this study is to investigate the efficiency of an innovative technique for strengthening masonry arches, based on the use of high strength steel cords embedded in either an epoxy (steel reinforced polymer) or mortar matrix (steel reinforced grout). Ten prototypes of brickwork arches strengthened by composite laminates were tested under a monotonic vertical load applied at the quarter-span. Load tests were performed to compare the behavior up to collapse of strengthened masonry arches; the influence of the types of reinforcement (steel and carbon fibers) and matrices (epoxy and cementitious), as well as location of the strengthening layer (intrados, extrados, and both) and the presence of anchorage systems has been investigated. The experimental results highlight the enhanced strength of the arches reinforced with steel cords, as well as the role of the mechanical anchoring with regard to the resulting final strength.     

Bond Behavior of Near-Surface Mounted FRP Strips Bonded to Modern Clay Brick Masonry Prisms: Influence of Strip Orientation and Compression Perpendicular to the Strip

In this paper the results of 18 pull tests performed on clay brick masonry prisms strengthened with near-surface mounted carbon fiber-reinforced polymer (CFRP) strips are presented. The pull tests were designed to add to the existing database and investigate variables significant to masonry construction. FRP was bonded to solid clay brick masonry; FRP aligned both perpendicular and parallel to the bed joint; and in the case of FRP reinforcement aligned parallel to the bed joint, compression applied perpendicular to the strip was used to simulate vertical compression load in masonry walls. Results including bond strength, critical bond length, and the local bond-slip relationship are presented as well as a discussion on the effect of the new variables on these results.     

Unreinforced Concrete Masonry Walls Strengthened with CFRP Sheets and Strips under Pendulum Impact

Impact tests using drop-weight pendulum on nine 1.2-m-high full-scale concrete masonry block walls were conducted to investigate the out-of-plane impact behavior of unreinforced masonry (URM) walls externally strengthened with carbon-fiber-reinforced polymer (CFRP) composites. Three strengthening schemes on one side of the wall were studied: continuous unidirectional and continuous woven sheets, discrete strips in a vertical pattern, and discrete strips in orthogonal and diagonal patterns. All walls were vertically positioned resting on a knife-edge support with one face leaning against two steel rollers close to the upper and lower edges of the wall. The impact load was applied at the wall center through a drop-weight pendulum impact tester with various drop heights. Test results revealed that using composite laminates or strips could significantly improve the impact performance of URM walls. The wall strengthened with continuous woven sheets performed better than the one with unidirectional sheet. With the same amount of fiber-reinforced polymer strip material, the wall with narrower but more closely spaced strips performed slightly better than the one with wider strips.     

Bond Between Near-Surface Mounted Carbon-Fiber-Reinforced Polymer Laminate Strips and Concrete

In recent years, a strengthening technique based on near-surface mounted (NSM) laminate strips of carbon-fiber-reinforced polymer (CFRP) has been used to increase the load-carrying capacity of concrete and masonry structures by introducing laminate strips into precut grooves on the concrete cover of the elements to be strengthened. The high experimentally derived levels of strength efficacy with concrete columns, beams, and masonry panels have presented NSM as a viable and promising technique. This practice requires no surface preparation work and, after cutting the groove, requires minimal installation time compared to the externally bonded reinforcing technique. A further advantage associated with NSM CFRP is its ability to significantly reduce the probability of harm resulting from fire, acts of vandalism, mechanical damage, and aging effects. To assess the bond behavior of CFRP to concrete, pullout-bending tests have been carried out. The influences of bond length and concrete strength on bond behavior are analyzed, the tests are described, and the results are presented and discussed in detail. Finally, a local stress-slip relationship is determined based on both experimental results and a numerical strategy.     

In-Plane Shear Behavior of Masonry Panels Strengthened with NSM CFRP Strips. I: Experimental Investigation

An experimental investigation was conducted to study the in-plane shear behavior of masonry panels strengthened with near-surface mounted (NSM) carbon fiber-reinforced polymer strips (CFRP). As part of the study four unreinforced masonry panels and seven strengthened panels were tested in diagonal tension/shear. Different reinforcement orientations were used including vertical, horizontal, and a combination of both. The effect of nonsymmetric reinforcement was also studied. The results of these tests are presented in this paper, and include the load-displacement behaviors, crack patterns, failure modes, and FRP strains. The results showed that the vertically aligned reinforcement was the most effective, with significant increases in strength and ductility observed. The dowel strength of the vertical reinforcement did not likely contribute significantly to the shear resistance of the masonry. Instead, it was likely that the vertical reinforcement acted in tension to restrain shear induced dilation and restrain sliding. In some panels cracking adjacent to the FRP strip, through the panel thickness was observed. This type of cracking reduced the bond between one side of the FRP strip and the masonry, and led to premature debonding. A comparison of the test results with the results of other tests from the literature is also presented in this paper.     

Flexural Capacity of Glass FRP Strengthened Concrete Masonry Walls

Fiber-reinforced polymers (FRP) can provide a strengthening alternative for unreinforced and underreinforced masonry. The ease with which FRP can be installed on the exterior of a masonry wall makes this form of strengthening attractive to the owner, considering both reduced installation cost and down time of the occupied structure. Six unreinforced concrete masonry walls (four at 1.8 m tall and two at 4.7 m tall) were tested in out-of-plane flexure up to capacity. The walls were strengthened with glass FRP composite composed of unidirectional E-glass fabric with an epoxy matrix. The composite was adhered to the surface of the masonry using the same epoxy with the fibers oriented perpendicular to the bed joints. General flexural strength design equations are presented and compared with the results of the testing. It was found that the equations overpredicted the actual capacity of the test specimens by no more than 20%.     

Wet Lay-Up Manufactured FRPs for Concrete and Masonry Repair: Influence of Water on the Properties of Composites and on Their Epoxy Components

The assessment of durability of fiber-reinforced polymers (FRPs), used to strengthen masonry or concrete structures, if subjected to weathering is a knotty problem. Environmental factors can have a significant effect on their performance in service. In order to investigate on this aspect, the mechanical behavior of two commercial composites, reinforced with unidirectional carbon and glass fibers, was analyzed after a long-term immersion in distilled water. For comparison purposes, three different commercial epoxy resins, used as primer, putty, or adhesive to manufacture and apply the composites through the wet lay-up technique to the surfaces to strengthen, were subjected to the same treatment. In order to take into account the peculiarities of the three cold-curing epoxy resins, a novel procedure to dry the specimens before the immersion treatment was used. The mechanical tests, performed on the composites before and after their immersion in water, evidenced that this agent has a limited effect only on the in-plane tensile strength of wet lay-up manufactured glass FRP, while the mechanical properties of carbon FRP are substantially unaffected by water. On the other hand, the effect of water on the thermal and mechanical characteristics of the three epoxy resins is quite severe, with significant reductions in the glass transition temperature, stiffness, and strength.     

Lateral Out-of-Plane Strengthening of Masonry Walls with Composite Materials

The structural behavior of masonry walls laterally strengthened with externally bonded composite materials to resist out-of-plane loads is theoretically and experimentally studied. Hollow concrete block masonry walls and solid autoclaved aerated concrete (AAC) block masonry walls are examined. A theoretical model that accounts for the cracking and the physical nonlinear behavior, the debonding of the composite layers, the arching effect, the interfacial stresses, and the unique modeling aspects of the laterally strengthened wall is presented. The experimental study includes loading to failure of 4 laterally strengthened masonry walls and 2 control walls. The experimental and analytical results point at the unique aspects of the lateral strengthening of masonry walls with composite materials. In particular, they reveal and explain the premature shear failure in laterally strengthened hollow concrete blocks walls and, on the other hand, demonstrate the potential of lateral fiber-reinforced polymer strengthening of AAC masonry walls. The laterally strengthened AAC masonry walls reveal improved strength, deformability, and integrity at failure characteristics.     

Experimental Behavior of FRP Strengthened Masonry Arches

This paper deals with the experimental behavior of solid clay brick masonry arches strengthened with glass fiber-reinforced polymer composites. Twelve half-scaled segmental masonry arches subjected to a load applied at the quarter span were tested under displacement control up to failure. The arches were built using handmade low strength bricks and a commercial lime-based mortar, trying to mimic ancient structures. Besides reference unreinforced arches, five different strengthening arrangements, including the use of spike anchors, were studied. The experimental results provide significant information for validation of advanced numerical models and analytical tools and for code drafting. The experimental results also show that (1) only continuous strengthening strategies are able to prevent typical local failure mechanisms of unreinforced arches; (2) strengthening at the intrados is the most effective option to increase strength; and (3) strengthening applied at the extrados provides the higher deformation capacity prior to failure, endowing arches with considerable ductility behavior.     

Experimental Response of Externally Retrofitted Masonry Walls Subjected to Shear Loading

Recent earthquakes have produced extensive damage in a large number of existing masonry buildings, demonstrating the need for retrofitting masonry structures. Externally bonded carbon fiber is a retrofitting technique that has been used to increase the strength of reinforced concrete elements. Sixteen full-scale shear dominant clay brick masonry walls, six with wire-steel shear reinforcement, were retrofitted with two configurations of externally bonded carbon fiber strips and subjected to shear loading. The results of the experimental program showed that the strength of the walls could be increased 13–84%, whereas, their displacement capacity increased 51–146%. This paper presents an analysis of the experimental results and simple equations to estimate the cracking load and the maximum shear strength of clay brick masonry walls, retrofitted with carbon fiber.     

External Prestressed Carbon Fiber-Reinforced Polymer Straps for Shear Enhancement of Concrete

The use of fiber-reinforced polymers (FRPs) for the strengthening and repair of existing concrete structures is a field with tremendous potential. The materials are very durable and, hence, ideally suited for use as external reinforcement. Although extensive work has been carried out investigating the use of FRPs for flexural strengthening, a fairly recent development is the use of these materials for the shear strength enhancement of concrete. The current system investigates the use of posttensioned, nonlaminated, carbon fiber-reinforced polymer (CFRP) straps as external shear reinforcement for concrete. Experiments were carried out on an unstrengthened control beam and beams strengthened with external CFRP straps. It was found that the ultimate load capacity of the strengthened beams was significantly higher than that of the control specimen. Existing design codes and analysis methods were found to underestimate the ultimate resistance of the control specimen and the strengthened beams. Nevertheless, the modified compression field theory provided insight into possible failure mechanisms and the influence of the strap prestress level on the structural behavior. It is concluded that the use of these novel stressed elements could represent a viable and durable means of strengthening existing concrete infrastructure.     

Fire Survivability of Externally Bonded FRP Strengthening Systems

The use of externally-bonded fiber-reinforced polymers (FRPs) to strengthen reinforced concrete (RC) structures is now widely recognized. However, a concern that continues to discourage the use of FRPs in many applications is their susceptibility to high temperature and fire. Although recent studies have shown that the fire endurance of appropriately designed and insulated FRP strengthened RC members is satisfactory, the specific performance of FRP systems at, and after exposure to, high temperature remains largely unknown. The results of tests on the residual properties after high-temperature exposure of various available FRP strengthening systems for concrete are reported; these include: tension coupon tests, single-lap FRP-to-FRP bond tests, direct tension FRP-to-concrete bond tests, and pull-apart FRP-to-concrete shear bond tests after exposure to temperatures up to 400°C. The data show that the allowable exposure temperatures for residual performance of externally bonded FRP systems lie between the glass transition temperature (Tg) and the thermal decomposition temperature of the resin systems used. The potential consequences for fire-safe design of FRP strengthened RC members are discussed. Material properties during a fire event are not specifically addressed.     

Interaction between Steel Stirrups and Shear-Strengthening FRP Strips in RC Beams

RC beams shear strengthened with either fiber-reinforced polymer (FRP) U-jackets/U-strips or side strips commonly fail due to debonding of the bonded FRP shear reinforcement. As such debonding occurs in a brittle manner at relatively small shear crack widths, some of the internal steel stirrups may not have reached yielding. Consequently, the yield strength of internal steel stirrups in such a strengthened RC beam cannot be fully used. In this paper, a computational model for shear interaction between FRP strips and steel stirrups is first presented, in which a general parabolic crack shape function is employed to represent the widening process of a single major shear crack in an RC beam. In addition, appropriate bond-slip relationships are adopted to accurately depict the bond behavior of FRP strips and steel stirrups. Numerical results obtained using this computational model show that a substantial adverse effect of shear interaction generally exists between steel stirrups and FRP strips for RC beams shear strengthened with FRP side strips. For RC beams shear strengthened with FRP U-strips, shear interaction can still have a significant adverse effect when FRP strips with a high axial stiffness are used. Therefore, for accurate evaluation of the shear resistance of RC beams shear strengthened with FRP strips, this adverse effect of shear interaction should be properly considered in design.     

Monte Carlo Simulation of Shear Capacity of URM Walls Retrofitted by Polyurea Reinforced GFRP Grids

A model proposed in the literature for the evaluation of the in-plane shear capacity of unstrengthened and strengthened concrete and clay brick unreinforced masonry (URM) walls was modified and calibrated following the results from an experimental research program. The tested walls were strengthened with grids made from glass fiber-reinforced polymer (GFRP) embedded within a rapid-setting sprayed polyurea. Various GFRP grid reinforced polyurea layouts were investigated, and consisted of strips oriented in either the vertical or horizontal direction and installed on one or both faces. The prediction models proposed in this paper were subsequently evaluated using a probabilistic Monte Carlo simulation (MCS) by considering the uncertainty and variability of the independent variables, which were assumed to follow a truncated normal distribution. Corroborated by the MCS, test results clearly show that the failure modes of the strengthened URM walls were affected by the strengthening scheme. Experimental and simulation results are presented and discussed in this paper.     

Tests on Seismically Damaged Reinforced Concrete Walls Repaired and Strengthened Using Fiber-Reinforced Polymers

The behavior of six 1:2.5-scale reinforced concrete cantilever wall specimens having an aspect ratio of 1.5, tested to failure and subsequently repaired and strengthened using fiber-reinforced polymer (FRP) sheets is investigated. Specimens were first repaired by removing heavily cracked concrete, lap splicing the fractured steel bars by welding new short bars, placing new hoops and horizontal web reinforcement, and finally casting nonshrink high-strength repair mortar. The specimens were then strengthened using FRP sheets and strips, with a view to increasing flexural as well as shear strength and ductility. In addition to different arrangements of steel and FRP reinforcement in the walls, a key parameter was the way carbon-FRP strips added for flexural strengthening were anchored; steel plates and steel angles were used to this effect. Steel plates were anchored using U-shaped glass-FRP (GFRP) strips or bonded metal anchors. Test results have shown that by using FRP reinforcement, the flexural and shear strength of the specimens can be increased. From the anchorage systems tested, metal plates combined with FRP strips appear to be quite efficient. The effectiveness of the bonded metal anchors used was generally less than that of the combination of plates and GFRP strips. In all cases, final failure of the FRP anchorage is brittle, but only occurs after the peak strength is attained and typically follows the fracture of steel reinforcement in critical areas, hence the overall behavior of the strengthened walls is moderately ductile.     

Experimental In-Plane Behavior of Tuff Masonry Strengthened with Cementitious Matrix–Grid Composites

Tuff buildings are a significant part of the Mediterranean area and are to be preserved from a structural viewpoint especially in seismic areas. Over the past few decades, the interest in strengthening of historical tuff masonry structures has led to developing specific and noninvasive architectural and engineering strategies. In the present paper, a comprehensive experimental program on tuff masonry panels is presented; the results are intended as a contribution to the knowledge of in-plane behavior of tuff masonry strengthened with composite materials. Particularly, a cement based matrix-coated alkali resistant glass grid system (CMG) was used to strengthen tuff masonry walls; different CMG layouts were selected, and overall performances were compared with those of as-built ones. The characterization of base materials was carried out first, followed by uniaxial tests of masonry and shear tests on triplets. Finally, tuff masonry panels were subjected to diagonal compression loading under displacement control in order to measure their in-plane deformation and strength properties, including the postpeak softening regime in view of seismic applications.     

Modeling Out-of-Plane Behavior of URM Walls Retrofitted with Fiber Composites

Although masonry is one of the oldest construction materials, its behavior has not been investigated as extensively as other construction materials. Out-of-plane failures are common in unreinforced masonry (URM) buildings constructed in seismic regions. Seven half-scale brick masonry walls were constructed, externally strengthened with vertical glass-fabric composite strips, and subjected to static cyclic out-of-plane loading. The flexural behavior of the tested specimens is characterized by three main stages corresponding to the first visible bed-joint crack, the first delamination, and the ultimate load. The main parameters being investigated in this study are the amount of composite, the height-to-thickness ratio h∕t, the tensile strain in composites, and the mode of failure. Based on the trends observed in the experimental phase, it was concluded that the behavior of the walls is best predicted with a linear elastic approach. It was also concluded that the ultimate strength method overestimates the flexural capacity and the ultimate deflection of the wall. Preliminary design recommendations are also proposed for tensile strain in the composite, maximum deflection, and maximum reinforcement ratio.     

Out-of-Plane Strengthening of Unreinforced Masonry Walls with Openings

Collapse of unreinforced masonry (URM) walls is the cause of many casualties during extreme loading events. The objective of this current research was to investigate effective and practical approaches for strengthening URM block walls with openings to resist extreme out-of-plane loads. Five full-scale masonry block walls were constructed. The walls had different opening configurations such as a single center window, one window off center, two windows, a wide window and a door. The walls were tested when subjected to uniformly distributed lateral load up to failure. The walls were then strengthened using carbon fiber-reinforced polymer laminate strips and then retested. The walls were set up in a vertical test frame and were subjected to cyclic out-of-plane distributed pressure using an airbag. Failure of the unstrengthened URM block wall was along the mortar joints. In the strengthened walls, failure occurred in the mortar joints as well as in concrete blocks near the carbon strips. The lateral load carrying capacity of the strengthened walls was found to be significantly higher than that of the unstrengthened walls and had much more ductile performance.