共查询到20条相似文献,搜索用时 109 毫秒
1.
介绍了承钢采用双联工艺,在用含钒钛铁水炼钢生产过程中通过改进砌炉工艺、执行一次拉成出钢操作、降低出钢温度、改造渣系、提高溅渣护炉效果等措施的实施大幅度提高转炉炉龄。 相似文献
2.
分析了渣碱度、渣中FeO含量、出钢温度等因素对溅渣 护炉效果的影响,阐述了马钢二钢厂通过调整造渣制度、降低出钢温度、选取合适的渣料及溅渣工艺参数等措施。取得了较好的溅渣护炉效果。 相似文献
3.
4.
5.
6.
介绍了上海梅山钢铁股份有限公司炼钢厂150 t转炉挡渣工艺。使用挡渣帽和挡渣塞双挡渣并配合下渣检测仪联合使用模式,可以控制钢水回磷质量分数在5×10-6左右;提高出钢口使用寿命,冶炼IF、SPHC和H-235P钢时,出钢口平均使用寿命可以分别达到98、110和117炉;减少每炉下渣量约100 kg,提高了钢水洁净度。 相似文献
7.
介绍了某钢厂采用120 t转炉→LF炉→扒渣/捞渣→LF炉→VD炉→板坯连铸工艺生产超低温压力容器用9Ni钢的冶炼实践情况,采用转炉+LF炉脱碳脱磷工艺,控制转炉出钢w[P]≤0.009%、w[C]≤0.05%,炉后平均脱P率74.3%,平均脱碳率51.2%,生产过程中,P的控制难度相比C的控制难度大。采用扒渣工艺下钢水的平均返磷率为16.89%,而捞渣工艺下钢水的平均返磷率为22.61%,扒渣工艺下钢水的返磷率低,但生产节奏长15~20 min,钢水量损失平均增加3.1 t/炉。镍板由转炉废钢槽加入调整为全部由LF炉加入后,Ni平均收得率提高了3.74%。通过对生产工艺的优化,中间包钢水P、S、N、T. O、C满足内控要求,钢水纯净度高,铸坯低倍中心偏析达到C类1.0~1.5级,表面质量良好,轧制钢板在-196℃下性能优良。 相似文献
8.
转炉溅渣护炉技术能大大提高转炉炉龄,已在国内外许多厂家得到迅速推广应用。新疆八一钢铁集团公司炼钢厂(简称八钢)由于转炉炉龄低的原因也在考虑应用溅渣护炉工艺来提高转炉炉龄,但又不能影响其生产节奏。本文从停工因素和冶炼周期的潜力挖掘方面做了大量调研性试验,并就溅渣护炉工艺对八钢生产节奏的影响作了预测。 相似文献
9.
分析了高R(碱度),高∑(FeO)炉渣溅渣护炉效果差的原因,阐述了马钢二钢厂通过降低R、∑(FeO)和出钢温度以提高溅渣护炉效果所采取的措施以及具体的工艺制度。 相似文献
10.
11.
�������£���־�� 《钢铁研究学报》2013,25(10):58-61
Thickness of convertor lining is important to guarantee safe production and prolong service life. Based on laser distance measurement technology, a laser thickness measurement system was put forward. Through coordinate transformation, this system can put the measurement point into the model that has already been built, and get the thickness of convertor lining at this point. And the isopachous line of the convertor lining can also be expressed using the coordinate in the two-dimensional figure. Industrial test result shows that the system has high practical value. 相似文献
12.
随着转炉的逐步大型化及炉龄的增加,转炉托圈与炉壳的连接形式由传统的三点球面支承式逐步向连杆吊挂式和弹簧钢板吊笼式发展,通过国内外考察结合实际应用,介绍了常用的三种形式的特点,对新建转炉有一定的参考意义。 相似文献
13.
本文介绍了乌克兰炼钢厂提高转炉废钢比的工艺概况,主要途径是向转炉内加入补充热源的燃料。介绍了该燃料的选择,加入方式和与其相适应的工艺制度。在采用综合措施后转炉废钢比可达到40%以上。 相似文献
14.
15.
16.
简要分析了AOD的工作原理、工艺操作过程;并结合AOD工艺操作特点,总结了AOD炉体设备、供配气系统、铁合金及副原料加料系统、烟气净化系统等相关设施的设备设计特点以及工艺设计特点。 相似文献
17.
The insertion of unconditioned latissimus dorsi muscle at the humerus was reattached in anesthetized goats to the first stage piston of a two stage mechanical-to-hydraulic energy convertor for a skeletal muscle powered ventricular assist device. To study a range of forces, pistons of different cross sectional areas were evaluated during thoracodorsal nerve stimulation. Each energy convertor piston was coupled hydraulically to an actuator on a Thoratec VAD (Thoratec Laboratories, Berkeley, CA) in a mock circulatory loop. Maximum force (70.1 +/- 10.8 N) was greatest for the largest piston, and stroke length (4.0 +/- 0.7 cm) was greatest for the smallest piston. However, maximum stroke work (1.2 +/- 0.5 J) and muscle powered VAD ejected stroke volume (45 +/- 17 ml) were greatest for the middle size piston. These results are consistent with a biomechanical model of whole muscle contraction that predicts that there is an optimum force that produces maximum cycle work. Thus, with a two stage energy convertor, by changing the ratio of the cross sectional areas of the energy convertor and muscle powered VAD actuator pistons, the effective mechanical advantage for the muscle can be optimized to produce more work output and muscle powered VAD flow. Skeletal muscle powered devices using such an energy convertor could provide completely implantable circulatory support free from batteries and other power conditioning hardware required with electromechanical systems. 相似文献
18.
冶炼45#钢使用LF炉精练工艺或者铁水预处理脱硫结合优化脱氧合金化技术,对这两种生产工艺方案进行了分析。综合考虑夹杂物控制、脱硫效果、铸坯质量和成本控制情况,选择铁水预处理-转炉-连铸作为生产工艺路线。 相似文献
19.
江铜贵冶转炉渣选矿二期工程调试与技改 总被引:1,自引:0,他引:1
江西铜业公司贵溪冶炼厂二期转炉渣选矿工程于2000年6月13日投产,由于设计及设备选型等诸多因素的影响,主要生产指标未能达到设计要求,后经一年多的调试与改造,工艺流程日趋完善,主要生产指标达到或超过设计标准,取得了较好的经济效益。 相似文献
20.
文章简要介绍了金昌冶炼厂转炉加长改造及GM45H-3型节能鼓风机应用的主要内容和运行效果,以及在运行初期出现的问题,对同类生产厂家的技术改造有着借鉴作用。 相似文献