Experiments on rockburst proneness of pre-heated granite at different temperatures: Insights from energy storage,dissipation and surplus

Many underground engineering projects show that rockburst can occur in rocks at great depth and high temperature, and temperature is a critical factor affecting the intensity of rockburst. In general, temperature can affect the energy storage, dissipation, and surplus in rock. To explore the influence of temperature on the energy storage and dissipation characteristics and rockburst proneness, the present study has carried out a range of the uniaxial compression(UC) and single-cyclic loading-unl...     

Optimizing the evolution of strength for lime-stabilized rammed soil

In the present study,unconfined compressive strength(q_u)values of two lime-treated soils(soil 1 and 2)with curing times of 28 d,90 d and 360 d were optimized.The influence of void/lime ratio was represented by the porosity/volumetric lime content ratio(η/L_(iv))as the main parameter.η/L_(iv) represents the volume of void influenced by compaction effort and lime volume.The evolution of qu was analyzed for each soil using the coefficient of determination as the optimization parameter.Aiming at providing adjustments to the mechanical resistance values,the η/L_(iv) parameter was modified to η/L_(iv)~C using the adjustment exponent C(to make q_u-η/L_(iv) variation rates compatible).The results show that with the decrease of η/L_(iv)~C.qu increases potentially and the optimized values of C were 0.14-0.18.The mechanical resistance data show similar trends between q_u and η/L_(iv)~C for the studied silty soil-ground lime mixtures,which were cured at ambient temperature(23±2)℃ with different curing times of 28—360 d.Finally,optimized equations were presented using the normalized strengths and the proposed optimization model,which show 6% error and 95% acceptability on average.     

一种新的岩爆倾向性指标

从岩石的变形和破坏过程中的能量储存和能量耗散出发，指出岩石的单轴抗压强度与单轴抗拉强度之比值可以表征结构较完整岩石的弹性变形能的储存能力以及峰值前后的应变量之比值可以表征岩石的能量储存与耗散之间的相对大小，提出用这两种比值的乘积作为岩爆倾向性指标。采用铜陵有色金属公司冬瓜山深部矿床的典型矿岩进行试验，对这种新的岩爆倾向性指标与现有的岩爆倾向性指标进行对比分析，结合该矿床实际的岩爆调查，说明新指标可以较好地表征岩石的岩爆倾向性，并提出了这种新指标判据的初步建议。     

确定弹性应变能指标的岩样卸载点的声发射方法

弹性应变能指标方法是岩爆倾向性评判中应用最多的一种方法,但该方法的一个技术难题是在实验中难以确定卸载点。在武夷山隧道工程的岩爆倾向性评价的室内试验中结合岩石的声发射监测技术,试图解决这个难题,并利用弹性应变能指标法对该隧道的岩爆倾向性进行了评价。试验研究结果表明,采用声发射监测技术并利用岩石峰值破坏前声发射突增的特性,可以较好地控制初次加载达到岩石峰值强度的80%以上,且在岩石不发生破坏的情况下及时卸载,从而能很好地满足弹性应变能指标法对岩石加卸载条件的要求,提高了测试结果的可靠性。同时,本实验得出该隧道具有发生中等岩爆的倾向性的结论。     

Characterization of large strain consolidation parameters of soft materials with time-variant compressibility at low effective stress

The one-dimensional (1D) large strain consolidation (LSC) of saturated soft materials that are deposited at very low-density usually exhibit time-variant compressibility (void ratio vs vertical effective stress ($e-{\sigma }_{\mathrm{v}}^{\prime }$)) relation. The 1D column-like model test serves as an effective approach for characterizing this consolidation characteristic if all the physical parameters (including the settlement rate, pore pressure and density) are measured. Unfortunately, the density measurement is not always realistic due to its high cost (e.g., with X-rays) and the time-effect must be roughly neglected by using an average compressibility relation. This can further lead to erroneous estimations of the materials’ permeability ($k$) relation (permeability vs void ratio ($k-e$)) in the LSC analysis. This paper presents two modifications on two conventional equations for compressibility and permeability, respectively. The first one describes the compressibility curve’s movement in the $\ln e-\ln {\sigma }_{\mathrm{v}}^{\prime }$ plane, and the other quantifies the ratio between the permeability calibrated by neglecting time-effect and its true value. These modifications originate from deep comparative analyses of several physical parameters between the column test and numerical prediction. Meanwhile, a simple hand-calculation procedure is proposed to estimate the new constants.     

Compressibility of biocemented loose sands under constant rate of strain,loading, and pseudo K0-triaxial conditions

The compressibility behavior of loose sands treated with Microbially Induced Carbonate Precipitation (MICP) is presented in this paper. The paper discusses the strain rate effects and evolution of at-rest earth pressure coefficient and elastic shear modulus during $K_0$-loading. The soil samples were prepared in a triaxial cell in which a biological solution containing the ureolytic bacteria Sporosarcina pasteurii was injected and held under a small back pressure. Cementation treatments were injected following an alternated top and bottom sequence. The constant rate of strain, constant rate of loading, and pseudo $K_0$-triaxial tests were performed at different strain and stress rates. On-specimen internal instrumentation consisting of a submersible load cell, three Hall Effect transducers, and vertical Bender Elements were used to control radial strains during $K_0$-loading and measure small-strain shear modulus changes. Based on shear wave velocity measurements, the MICP-treated sand was lightly cemented and displayed soil-like behavior. The experimental results demonstrated a significant reduction in soil compressibility after MICP treatment. The material response was remarkably similar for every tested strain rate. The very small values of axial strains measured for the biotreated samples in relation to untreated control specimens for vertical effective stress levels below 200 kPa is evidence of the suitability of this treatment and shows its potential for use in field applications at relatively shallow depths.     

The relation between the state indices and the characteristic features of undrained behaviour of silty sand

The characteristic features of a series of isotropically and K₀-consolidated undrained triaxial compression behaviour of a silty sand were investigated for a range of initial void ratio ($e)$ and mean effective confining stress ($p^{\prime }$). The silty sand used in this study contained about 10% natural fines. The critical state line (CSL) of K₀-consolidated specimens, K₀U was slightly lower than the CSL for isotropically consolidated specimens, CIU. The respective CSLs for K₀U and CIU were used to define state indices, such as state parameter ($\psi )$, state index ($I_s$), state pressure index ($I_p$) and modified state parameter (${\psi }_m$), within critical state soil mechanics (CSSM) framework. It was found that each state index exhibit a unique relation with liquefaction potential, irrespective of consolidation type, however different relationships were observed between state indices and the stress ratio at the triggering of liquefaction, ${\eta }_{\mathit{IS}}$ or the liquefaction resistance, $q_{\mathit{IS}}$. The correlation of characteristic features of undrained shearing (i.e., liquefaction potential, ${\eta }_{\mathit{IS}}$ and $q_{\mathit{IS}}$) and drained shearing (maximum rate of volume change, ${\left(d{\epsilon }_v/d{\epsilon }_a\right)}_{\mathit{m}\mathit{a}\mathit{x}}$) with state indices were compared statistically in terms of root mean square deviations (RMSD). All characteristic features of undrained shearing generally showed the best correlation with $I_p$ in term of RMSDs, however $\psi$ showed comparatively wider scatter for the specimens showing flow and limited flow behaviour.     

On the influence of grain shape on the cumulative deformations in sand under drained high-cyclic loading

The cumulative response of three granular materials with significantly different grain shape and surface characteristics (glass beads, natural sand with subrounded grains and crushed sand with very angular particles) but identical grain size distribution curve has been studied in drained cyclic triaxial tests. For each material, several tests with 100,000 cycles and different amplitudes, densities, average mean pressures and average stress ratios have been performed. In case of glass beads and natural sand, an approximately square relationship between the residual strain accumulation rates and stress or strain amplitude was found (${\stackrel{?}{\epsilon }}^{\mathrm{a}\mathrm{c}\mathrm{c}}$ ～ ${\left({\epsilon }^{\mathrm{a}\mathrm{m}\mathrm{p}\mathrm{l}}\right)}^2$), while an almost proportional dependence was measured for the crushed sand (${\stackrel{?}{\epsilon }}^{\mathrm{a}\mathrm{c}\mathrm{c}}$ ～ ${\epsilon }^{\mathrm{a}\mathrm{m}\mathrm{p}\mathrm{l}}$). The largest differences in the cumulative response of the three tested materials were observed regarding the pressure-dependence of ${\stackrel{?}{\epsilon }}^{\mathrm{a}\mathrm{c}\mathrm{c}}$. For glass beads and (less pronounced) for natural sand, the residual strain accumulation rates decreased with average mean pressure, while the opposite tendency was obtained for the crushed sand. At small pressures, the residual strains were much larger for the glass beads than for the natural sand and particularly the crushed sand, while these differences in the accumulated strains almost diminished at larger pressures. Independent of the shape and the surface characteristics of the particles, it was confirmed that the average stress ratio is the governing parameter of the cyclic flow rule. Finally, the parameters of the high-cycle accumulation (HCA) model proposed by Niemunis et al. (2005) were analyzed considering the grain shape parameters (aspect ratio, circularity) obtained from an automated grain shape analysis.