提高间接测量精度的方法

在实际的精密测量过程中,在现有指定仪器精度的基础上,将测量值尽量接近于真值,是我们目前最值得探讨的问题。本文从分析误差在计算过程中的传播系数开始讨论。１　误差产生的原因设ｘ１、ｘ２是Ｘ１、Ｘ２的最可信赖值,且Ｘ１、Ｘ２为独立变量,假设对Ｘ１、Ｘ２进行间接测量,那么函数Ｙ＝ｆ（Ｘ１,Ｘ２）在点（ｘ１,ｘ２）处的Ｔａｙｌｏｒ展开式为：ｆ（Ｘ１,Ｘ２）＝ｆ（ｘ１,ｘ２）＋［（ｆｘ１）,（Ｘ１－ｘ１）＋（ｆｘ２）,（Ｘ２－ｘ２）］＋１２！［（２ｆｘ２１）（Ｘ１－ｘ１）２＋２（２ｆｘ１…     

X射线影像存储材料BaF_xCl_（2－x）Eu~（2＋）的制备及其热释发光和

本文采用了不同温度下两次烧结的新方法，制备了系列Ｘ射线影象存储材料ＢａＦ＿ｘＣｌ＿（２－ｘ）：Ｅｕ￣（２＋）（ｘ＝０．９０，０．９５，１．００，１．０５，１．１０１．１５）。通过改变Ｆ／Ｃｌ比值，研究了在Ｘ射线辐照后ＢａＦ＿ｘＣｌ＿（２－ｘ）：Ｅｕ￣（２＋）的热释发光性质，给出了热释发光峰的温度与缺陷种类的关系。最后，我们研究了ＢａＦ＿ｘＣｌ＿（２－ｘ）：Ｅｕ￣（２＋）的光激励发光性质，给出了Ｆ／Ｃｌ比值与光激励发光强度的关系。     

一类环面微分方程的全局结构分析

本文讨论了从交叉耦合锁相环（ＣＣＰＬＬ）中提出的一类环面双参数微分方程ｘ＝α１（（２β１－ｆ（ｘ＋ｙ）－ｆ（ｘ－ｙ），ｙ＝α２（２β２－ｆ（ｘ＋ｙ）＋ｆ（ｘ－ｙ）的分岐现象，通过对系统的全局结构分析，证明该系统分岐属鞍一结点分岐，分歧曲线为β１＋β２。本文结果对ＣＣＰＬＬ的设计具有指导意义。     

一类平面微分系统极限环的存在唯一性

得到了平面微分系统ｘ＝－ｙ＋δｘ＋ａｘ＾２ｍ＋ｂｘ＾２ｍ（ｘ）,ｙ＝ｘ＾２ｎ－１（ｍ,ｎ∈Ｎ）极限环的存在性,唯一性和不存在性的完整结果。     

退火对氧敏CeO2—x薄膜结构及电子组态的影响

用射频磁控溅射法制备了ＣｅＯ２－ｘ高温氧敏薄膜，用Ｃｅ３ｄ的ＸＰＳ谱计算了Ｃｅ＾３＋浓度，研究了退火条件对氧敏ＣｅＯ２－ｘ薄膜的晶体结构及电子组态的影响，ＸＲＤ和ＡＦＭ分析表明，薄膜经９７３Ｋ至１３７３退火后，形成了ＣａＦ２型结构的ＣｅＯ２－ｘ其晶粒大小明显依赖于退火条件和膜厚，退火温度在９７３Ｋ至１１７３Ｋ时（２００）晶面是择优取向的，在１３７３退化４ｈ后，可得到热力学稳定的ＣｅＯ２－ｘ在退火前     

高氢稀释硅烷加乙烯法制备纳米硅碳薄膜

在等离子体化学气相沉积系统（ＰＥＣＶＤ）中，使用高氢稀释硅烷（ＳｉＨ４）加乙烯（Ｃ２Ｈ４）为反应气氛制备了纳米硅碳（ｎｃ－ＳｉＣｘ＾２Ｈ）薄膜，随着（Ｃ２Ｈ４＋ＳｉＨ４）／Ｈ２（Ｘｇ）从５％时，由于Ｈ蚀刻效应的减弱，薄膜的晶态率从４８％下降到８％，平均晶粒尺寸在３．５－１０ｎｍ。当Ｘｇ≥６％时，生成薄膜为非晶硅碳（ａ－ＳｉＣｘ＾２Ｈ）薄膜。ｎｃ－ＳｉＣｘ＾２Ｈ薄膜的电学性质具有与薄膜的晶态率紧密相     

捕食种群具有常数收获率并具有Ⅲ类功能性反应的食饵-捕食系统

讨论了捕食种群具有常数收获率,并具有Ⅲ类功能性反应的食饵－捕食系统ｘ＝ｒｘ（１＝－ｘ／ｋ）－ωｘ＾２ｙ／ｘ＾２＋ａ;ｙ＝ｙ（－ｄ＋ｃｗｘ＾２／ｘ＾２＋ａ）＋μ给出了此系统在第一象限内的有所可能的拓扑结构,并证明了此系统在第一象限内至少可以存在两个象限环。     

锂快离子导体Li_(1 2x y)Al_xYb_yTi_(2-x-y)Si_xP_(3-x)O_(12)系统的研究

以ＬｉＴｉ２（ＰＯ４）３为基以天然高岭石为起始原料,经高温固相反应（９５０～１１５０℃）制得了 一系列锂快离子导体材料Ｌｉ１＋２ｘ＋ｙＡｌｘＹｂｙＴｉ２－ｘ－ｙＳｉｘＰ３－ｘＯ１２（以下简称Ａｌ－Ｙｂ－Ｌｉｓｉｃｏｎ）．系统 的合成温度随ｘ和ｙ值的增大而降低．应用交流阻抗技术测定的电导率数据结果表明ｙ＝０．３, ｘ＝０．１的合成物的电导率最好,４００℃时电导率达２．４５×１０－２Ｓ／ｃｍ, ２００～４００℃内的电导激 活能为３８．３ｋＪ／ｍｏｌ．ＸＲＤ分析结果表明在ｙ＝０．３,ｘ≤０４及ｙ＝０．５,ｘ≤０．３的组成范围内 均能得到空间群为Ｒ３ｃ的合成物．     

溶胶—凝胶法合成Li2＋xBxSi1—xO3及其离子导电性能的研究

用溶胶－凝胶法合成了Ｌｉ２＋ｘＢｘＳｉ１－ｘＯ３（ｘ＝０－０．５）,发现形成固溶体的范围是０〈ｘ≤０．２。对其离子导电性的研究发现,当ｘ＝０．３时出现电导率极大值。     

一类可逆生化反应动力系统的定性分析

研究了生化反应中一类可逆饱和反应的数学模型：｛ｄｘ／ｄｔ＝（ｙ＋ｂ）（Ａ－Ｂｘ－ｘｙ＋Ｃｙ＾２）,ｄｙ／ｄｔ＝（ｙ＋ｂ）（Ｂｘ＋ｘｙ－Ｃｙ＾２）－ａｙ。应用微分方程定性理论,比较完整地解决了该系统极限环的存在性、叭一性和不存在性等问题。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...