Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Preparation and characterization of maleic anhydride‐g‐polypropylene/diamine‐modified clay nanocomposites

Polypropylene (PP)/montmorillonite (MMT) nanocomposites were prepared by compounding maleic anhydride‐g‐polypropylene (MAPP) with MMT modified with α,ω‐diaminododecane. Structural characterization confirmed the formation of characteristic amide linkages and the intercalation of MAPP between the silicate layers. In particular, X‐ray diffraction patterns of the modified clay and MAPP/MMT composites showed 001 basal spacing enlargement as much as 1.49 nm. Thermogravimetric analysis revealed that the thermal decomposition of the composite took place at a slightly higher temperature than that of MAPP. The heat of fusion of the MAPP phase decreased, indicating that the crystallization of MAPP was suppressed by the clay layers. PP/MAPP/MMT composites showed a 20–35% higher tensile modulus and tensile strength compared to those corresponding to PP/MAPP. However, the elongation at break decreased drastically, even when the content of MMT was as low as 1.25–5 wt %. The relatively short chain length and loop structure of MAPP bound to the clay layers made the penetration of MAPP molecules into the PP homopolymer phase implausible and is thought to be responsible for the decreased elongation at break. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 307–311, 2005     

Novel phenylethynyl‐endcapped polyimide oligomers: Synthesis and characterization

A series of novel phenylethynyl‐endcapped polyimide oligomers were prepared by polycondensation of an aromatic diamine mixture of 1,3‐bis(4‐aminophenoxy) benzene (1,3,4‐APB) and 3,4′‐oxydianiline (3,4′‐ODA) with different aromatic dianhydrides including 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐(hexafluoro isopropylidene)diphthalic anhydride (6FDA), 4,4′‐oxydiphthalic anhydride (ODPA), and 4,4′‐[2,2,2‐trifluoro‐1‐(3′,5′‐bis‐(trifluoro‐methyl)phenyl)ethylidene]diphthalic anhydride (9FDA) in the presence of 4‐phenyl‐ethynylaniline (PEA) as endcapping agent in aprotic solvent at elevated temperature. The chemical structures, thermal behavior, and melt rheological properties of the synthesized polyimide oligomers were investigated. Experimental results indicated that the fluorinated polyimide oligomers derived from 6FDA (PI‐2) and 9FDA (PI‐4) are amorphous solid resins and exhibited lower melt viscosities than those prepared from the unfluorinated aromatic dianhydrides such as BPDA and ODPA. The BPDA‐based polyimide oligomers with a molar ratio of 1,3,4‐APB/3,4′‐ODA = 50:50 (PI‐5) showed lower melt viscosity than those derived from a mixture of 1,3,4‐APB and 3,4′‐ODA with molar ratios of 75:25 and 100:0, respectively. In addition, the melt viscosity of the polyimide oligomers increased obviously with increasing of the polymer calculated molecular weights. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Sorption of uranyl ions from aqueous solutions using crosslinked maleic anhydride‐octene‐styrene terpolymer

Maleic anhydride‐octene‐styrene terpolymer has been modified with allylic alcohol and methylmethacrylate to prepare a new crosslinked functional polymer sorbent. The sorption behaviors of uranyl ions on the optimum sorption conditions were determined. The synthesized crosslinked polymer sorbent has a network structure and contains carboxylic acid, carbonyl, and ester groups, all of which are capable of interacting with metal ions. The maximum experimental sorption capacity of the sorbent for uranyl ions has been measured as 1.25 mmol g^?1. Langmuir and Freundlich isotherm constants and correlation coefficients for the present system have been calculated and compared. Uranyl ions are desorbed from the sorbent by treatment with hydrocholric and nitric acids at various concentrations. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and characterization of polyethylene‐g‐maleic anhydride–styrene/montmorillonite nanocomposites

It is difficult to prepare polyethylene/montmorillonite by direct melt mixing because of the difference in character between polyethylene and montmorillonite. Therefore, it is necessary to modify polyethylene with polar groups, which can increase the hydrophilicity of polyethylene. At the same time, the inorganic montmorillonite should be modified with long‐chain alkyl ammonium to increase the basing space between the interlayers. Thus, through the grafting of the polar monomer onto the main chain of polyethylene by reactive extrusion, polyethylene/montmorillonite nanocomposites can be prepared by the melt mixing of the grafter and organic montmorillonite. Fourier transform infrared has been used to prove that the monomers are grafted onto polyethylene. X‐ray diffraction and transmission electron microscopy have been employed to characterize the nanocomposites. Furthermore, thermogravimetric analysis measurements show that the thermal stability of the nanocomposites is improved in comparison with that of the virgin materials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 805–809, 2006     

Effect of phthalic anhydride‐based hyperbranched polyesteramide on cement characteristics

Hyperbranched polyesteramides (HB₁ and HB₂) were prepared by the bulk reaction between phthalic anhydride (PhAn) with either diisopropanolamine (DiPA) or diethanolamine (DEA), respectively. The hyperbranched polyesteramides were characterized by IR, GPC, ¹H‐NMR, and thermal analysis (TGA and DSC). The effects of solutions of 1, 3, and 5 wt % HB₁ and HB₂ on the properties of Ordinary Portland Cement (OPC) and Portland Limestone Cement (PLC) were studied. Measurements of water of consistency, setting times, bulk density, apparent porosity, and compressive strength for the cement pastes were performed. Some selected cement pastes were characterized by IR and SEM photos. The results showed that HB₁ and HB₂ slightly increased the compressive strength, the combined water and density while decreased the apparent porosity. IR of the formed phases showed increase in the intensities of the spectra for the cement pastes mixed with HB₁ and HB₂ when compared with those of the blank cement pastes. SEM images showed that the incorporation of HB₁ and HB₂ affected only shape or morphology and crystallinity of the formed hydrates. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Crystallization kinetics of maleic anhydride‐modified iPP studied by POM

Melt nucleation and crystallization behavior of homo‐isotatic polypropylene (homo‐iPP), maleic anhydride (MAH)‐grafted‐iPP, and MAH‐modified iPP, produced from iPP and a small amount of MAH‐grafted‐iPP, was investigated by polarizing optical microscopy (POM), at T_c = 121–135^oC. Nucleation processes at a given T_c were faster for modified PP as compared to neat iPP. The induction time for nucleation increased nonlinearly with increasing T_c and decreased for modified PP, probably as a result of promoted heterogeneous nucleation due to the presence of carbonyl groups of MAH‐grafted‐PP. The average spherulite sizes were decreased by modification, and the growth rate was enhanced in maleated PP and modified PP. The induction time approach was applied to the results obtained by POM to compare the tendency for heterogeneous nucleation of neat and MAH‐modified PP. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3107–3118, 2000     

Dye bleaching and phenol precipitation by phthalic anhydride‐modified horseradish peroxidase

The phenol precipitation and dye bleaching capabilities of phthalic anhydride–modified horseradish peroxidase C (PA–HRP) were compared with those of native HRP C and ethylene glycol‐ bis‐(succinic acid N‐hydroxysuccinimide ester)–modified HRP (EG–HRP) reported previously. Removal efficiency (percentage of phenol removed from solution under experimental conditions) was determined for native HRP and both modified forms. Removal efficiencies at 37 °C were very similar, with >95% removal in each case. Removal efficiencies were less at 70 °C overall (range 25–45%) but PA–and EG–HRP removed up to 50% more phenol than native HRP. The three HRP forms showed similar dye bleaching performance at 37 °C in the presence of H₂O₂ and accelerators (up to 86% colour removal). PA–and EG–HRP showed slightly greater bleaching abilities at 65 °C than native HRP for some of the dye/accelerator combinations tested. Modified HRPs performed better in 40% (v/v) mixtures of dioxane or dimethylformamide. © 2000 Society of Chemical Industry     

Blend compatibilizers based on silane‐ and maleic anhydride–modified polyolefins

Polypropylene (PP)/polyamide blends were compatibilized with PP modified with vinylsilane or maleic anhydride and ethylene–propylene random (EPR) copolymer modified with maleic anhydride. The thermal behavior, mechanical properties, and morphology of the blends were investigated. Thermal analysis showed that the polyamide crystallization temperatures shifted downward with all compatibilizers, whereas its melting behavior did not change. On the other hand, polypropylene crystallization temperatures shifted upward in all cases, except for blends containing EPR modified with maleic anhydride. Tensile strength and elongation at break increased for blends compatibilized with modified PP. Blends containing up to 7% of EPR modified with maleic anhydride did not show good yield stresses. The morphology of the blends showed a finer dispersion of the polyamide minor phase in the PP matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2492–2498, 2003     

Polypropylene/natural rubber composites filled with recycled newspaper: Effect of chemical treatment using maleic anhydride‐grafted polypropylene and 3‐aminopropyltriethoxysilane

A study on effect of chemical treatment using maleic anhydride‐grafted polypropylene (MAPP) and 3‐aminopropyltiethoxysilane (3‐APE) was investigated. The performance of the MAPP and 3‐APE were investigated by means of torque development, mechanical properties, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy morphology, and water absorption. The results revealed that the use of MAPP or 3‐APE in the composites has increased the stabilization torque, tensile strength, Young's modulus, water absorption, and thermal stability of the PP/NR composites. The incorporation of MAPP in the composites shows higher stabilization torque, tensile strength, E_B, Young's modulus, and lower water uptake when compared with the use of 3‐APE in the PP/NR composites. TGA and DSC results indicated that primary and secondary peak of DTG curve, initial degradation temperature (T₀), degradation temperature (T_deg), melting temperature (T_m), heat of fusion of composites (ΔH_f(com)), crystallinity of composites (X_PP), and PP (X_PP) increased, while total weight loss and thermal degradation rate decreased for both treated composites. The MAPP‐treated RNP‐filled PP/NR composites were found to be more thermal resistance and more crystalline than 3‐APE‐treated filled PP/NR RNP composites. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Fracture toughness evaluation of K resin® grafted with maleic anhydride‐ compatibilized polyamide 6/K resin® blends

The mechanical behavior and fracture toughness of polyamide 6 (PA6)/K resin^® (K) blends, with and without maleic anhydride‐grafted K resin^® (K‐g‐MAH) incorporated, have been investigated. The results showed that the tensile strength, elongation at break and impact strength of PA6/K blends were improved considerably on incorporating K‐g‐MAH. This results from the improvement of compatibility between the PA6 and K phases. The essential work of fracture (EWF) method was employed to determine the fracture toughness of PA6/K blends with and without K‐g‐MAH incorporated. The effect of composition on the EWF parameters of the blends was particularly investigated. The results showed that a significant improvement in the specific EWF (w_e) of PA6/K blends occurred when K‐g‐MAH was incorporated. The effect of K‐g‐MAH content on the fracture toughness of the PA6/K/K‐g‐MAH blends was mainly achieved through its influence on the specific essential and nonessential work of fracture in the yielding process. Copyright © 2007 Society of Chemical Industry     

Effect of maleic anhydride‐grafted polypropylene on polypropylene/recycled acrylonitrile butadiene rubber/empty fruit bunch composite

The effect of maleic anhydride‐grafted polypropylene (PP‐g‐MAH) as a compatibilizer on the properties of polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr)/empty fruit bunch (EFB) composites were studied. The composites were melt mixed using a heated two roll mill at 180°C and a speed of 15 rpm with six different compositions (100/0/10, 80/20/10, 70/30/10, 60/40/10, 50/50/10, 40/60/10 phr). The effects of PP‐g‐MAH on mechanical, morphological and chemical properties of the PP/NBRr/EFB composites were examined. The PP‐g‐MAH compatibilized composites have higher tensile values compare to uncompatibilized composites. Scanning electron microscopy showed better adhesion between EFB and PP/NBRr matrices in the presence of PP‐g‐MAH. Better interaction was formed between EFB and PP/NBRr matrices via C‐O‐C ester bonds as indicated by FTIR analysis. J. VINYL ADDIT. TECHNOL., 24:275–280, 2018. © 2016 Society of Plastics Engineers     

Evaluation of toughening mechanisms of polypropylene/ethylene–octene copolymer/maleic anhydride‐grafted poly(ethylene‐co‐octene)/clay nanocomposite

The toughness of a polypropylene (PP)/ethylene‐octene copolymer (EOC)/maleic anhydride‐grafted poly(ethylene‐co‐octene) (EOC‐g‐MA)/clay nanocomposite and blends of PP/EOC and PP/EOC/EOC‐g‐MA was investigated using Charpy impact and single‐edge‐notch tensile (SENT) tests. In order to understand the toughening mechanisms, impact fracture surfaces and damage zones of single‐edge‐notch samples were studied with scanning electron microscopy and transmission optical microscopy, respectively. It was observed that the addition of EOC‐g‐MA to PP/EOC blend led to improvements in both impact strength and fracture energy of SENT tests because of the enhanced compatibility of the blend, which resulted from reduced EOC particle size and improved interfacial adhesion, and the decreased crystallinity of PP. The incorporation of clay to PP/EOC/EOC‐g‐MA blend caused a further increase of the toughness, owing to the greater decrease in the size of elastomer particles, to the presence of clay tactoids inside the elastomer phase and presumably to debonding of clay layers during the low‐speed SENT tests. The results of microscopic observations showed that the main toughening mechanism in PP/EOC/EOC‐g‐MA blend and PP/EOC/EOC‐g‐MA/clay nanocomposite is crazing. Copyright © 2012 Society of Chemical Industry     

Enhanced dielectric performances of polypropylene films via polarity adjustment by maleic anhydride‐grafted polypropylene

Maleic anhydride‐grafted polypropylene (MA‐g ‐PP) was hybridized with pure PP to form hybrid films with the aim to enhance the dielectric performances of the PP film via polarity adjustment. The changes of microstructure and crystallinity of PP matrix by MA‐g ‐PP incorporation were studied, and the polarity change was identified by the surface wettability. The dielectric behaviors of the hybrid films were explored. Increasing polarity of PP film leads to increase in dielectric constant but decrease in breakdown strength, and a balance is achieved in 10 vol % MA‐g ‐PP/PP hybrid film, with the maximum discharge energy density reaching 1.96 J cm^?3 and charge–discharge efficiency as high as 96%. The ultralow loss is attributed to the dense and homogeneous microstructure together with increased crystallinity induced by incorporation of MA‐g ‐PP. These PP‐based films with increased polarity not only show enhanced dielectric performances but also provide a type of matrix that would be compatible with polar fillers to further increase dielectric properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45029.     

Optimization of Nannochloropsis oculata growth using the response surface method

Optimization of Nannochloropsis oculata growth was undertaken using the response surface method. A central composite design was defined to study the effects of temperature, pH, incident light intensity and aeration rate on the maximum growth rate of the microalga. Using statistical analysis, the first model calculated to fit results was twice improved. The final model obtained was used to clarify the effects of each factor and their interactions on the growth of Nannochloropsis oculata. The optimum growth conditions of this microorganism were also estimated as 21 °C, 52 µmol photons m^?2 s^?1, pH 8.4 and 14.7 VVH of aeration rate. These conditions were tested and validated experimentally since the maximum growth rate achieved with these parameters, 0.0359 h^?1, is the best reported in this study. Copyright © 2006 Society of Chemical Industry     

Preparation and characterizations of RTV epoxy blends using amide maleic anhydride‐g‐liquid polybutadience as both reactive toughening and curing components

Amide maleic anhydride‐g‐liquid polybutadience (AMALPB) was synthesized using maleic anhydride‐g‐liquid polybutadience (MALPB) with ethylenediamine (EDA), and its structure was confirmed by FTIR and ¹H‐nuclear magnetic resonance spectra, respectively. It was then used as a reactive toughening agent to make blends with diglycidyl end‐capped poly(bisphenol‐A‐co‐epichlorohydrin epoxy cured at room temperature. Their thermal decomposing behaviors did not show much difference because both EDA and AMALPB possessed similar aliphatic groups. All their glass transition temperatures (T_g) increased more than 10 °C than that of the neat epoxy, and with the addition of AMALPB, the blends were greatly strengthened upon heating as show from their storage moduli. When AMALPB was added at 10 wt %, its elongation at break increases to a maximum of 8.8% which was about two times higher than that of the neat epoxy, and its tensile strength also increased. However, the excessive addition of AMALPB resulted in an apparent decline in their tensile strength at content above 20%. The simultaneous improvements in both tensile strength and strain were attributed to the existence of well‐dispersed rubber particles in the continuous matrices performing plastic deformation that resulted from the chemical bonds of interfaces among the rubber particles and matrix, and meanwhile, inducing the deflection of the cracks. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45985.     

Aggregate structure and effect of phthalic anhydride‐modified soy protein on the mechanical properties of styrene‐butadiene copolymer

The aggregate structure of phthalic anhydride (PA) modified soy protein isolate (SPI) was investigated by estimating its fractal dimension from the equilibrated dynamic strain sweep experiments. The estimated fractal dimensions of the filler aggregates were less than 2, indicating that these particle aggregates have a distorted or broken two‐dimensional sheet‐like structure. The results also indicated that the aggregate structure has a greater effect on the composite reinforcement than the overall aggregate size. Tensile strength, elongation, Young's modulus, and toughness of hydrolyzed/modified soy composites are comparable with those of carbon black reinforced composites at 10–15% filler fraction. The moduli of PA‐modified SPI composites were less sensitive to the pH of the composite preparation compared to the unmodified SPI. The composites prepared at acidic pH, with lower filler fraction, or filled with hydrolyzed/modified SPI are more elastic and less fatigue. The composites of PA‐modified SPI had better recovery properties when prepared at acidic instead of alkali pH. PA‐modified hydrolyzed SPI composites prepared at acidic pH showed a similar recovery property to that of carbon black reinforced composites, but with greater shear elastic moduli. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of glass fiber on the electrical resistivities of polyoxymethylene/maleic anhydride‐grafted polyethylene/multiwalled carbon nanotube composites

The effect of glass fiber (GF) on the electrical resistivities of polyoxymethylene (POM)/maleic anhydride‐grafted polyethylene (MAPE)/multiwalled carbon nanotube (MWCNT) composites is investigated. The POM/MAPE/MWCNT composites at a MWCNT loading of 0.75% are nonconductive because most of MWCNTs are isolated in the MAPE islands, and their electrical resistivities decrease significantly after the addition of GF because of the formation of MAPE‐coated GF structure, which facilitates the formation of conductive paths and was confirmed by field emission scanning electron microscopy (FESEM). The formation of MAPE‐coated GF structure is attributed to the interaction between GF and MAPE during melt compounding, as contrasted by the uncoated GF using high‐density polyethylene (HDPE) instead of MAPE. Nonconductive POM/5–20% MAPE/0.75% MWCNT composites become conductive upon the addition of 20% GF. This preparation method for conductive materials can be generalized to POM/5–20% maleic anhydride‐grafted polypropylene (MAPP)/0.75% MWCNT composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41794.     

Optimization of acrylonitrile removal by activated carbon‐granular using response surface methodology

A statistical Box–Behnken design of experiments was performed to evaluate the effects of individual operating variables and their interactions on the acrylonitrile (AN) removal of C₀ = 100 mg/L as fixed input parameter. The variables examined in this study included activated carbon‐granular (AC) dosage, w, temperature, T, and time of contact, t. The significant variables and optimum conditions were identified (w = 4 g/L, T = 30°C, and t = 120 min with AN uptake of 23.97 mg/g of AC) from statistical analysis of the experimental results using response surface methodology (RSM).     

Melt rheological properties of polypropylene–polyamide6 blends compatibilized with maleic anhydride‐grafted polypropylene

The melt rheological properties of binary uncompatibilized polypropylene–polyamide6 (PP–PA6) blends and ternary blends compatibilized with maleic anhydride‐grafted PP (PP–PP‐g‐MAH–PA6) were studied using a capillary rheometer. The experimental shear viscosities of blends were compared with those calculated from Utracki's relation. The deviation value δ between these two series of data was obtained. In binary PP–PA6 blends, when the compatibility between PP and PA6 was poor, the deformation recovery of dispersed PA6 particles played the dominant role during the capillary flow, the experimental values were smaller than those calculated, and δ was negative. The higher the dispersed phase content, the more deformed the droplets were and the lower the apparent shear viscosity. Also, the absolute value of δ increased with the dispersed phase composition. In ternary PP–PP‐g‐MAH–PA6 systems, when the compatibility between PP and PA6 was enhanced by PP‐g‐MAH, the elongation and break‐up of the dispersed particles played the dominant role, and the experimental values were higher than calculated. It was observed that the higher the dispersion of the PA6 phase, the higher the δ values of the ternary blends and the larger the positive deviation. Unlike uncompatibilized blends, under high shear stress with higher dispersed phase content, the PP‐g‐PA6 copolymer in compatibilized blends was pulled out from the interface and formed independent micelles in the matrix, which resulted in reduced total apparent shear viscosity. The δ value decreased with increasing shear stress. Copyright © 2006 Society of Chemical Industry