Synthesis of styrene–ethylene–butylene–styrene triblock copolymer‐g‐polylactic acid copolymer and its potential application as a toughener for polylactic acid

The copolymer of styrene–ethylene–butylene–styrene triblock copolymer‐g‐polylactic acid (SEBS‐g‐PLA) was successfully prepared using a novel solvothermal synthetic method, in which the graft copolymerization of PLA and SEBS was simply performed in cholorform solution at 100–150°C with benzoyl peroxide (BPO) as initiator. The effect of various factors including the reaction temperature and time and the content of BPO and PLA on the graft copolymerization was investigated in detail. It is found that the optimal reaction condition for the grafted copolymers SEBS‐g‐PLA was 120°C for 5 h, while the optimal formulation of SEBS/PLA/BPO was 5 g/2 g/0.5 g in 30 mL chloroform. The properties and microstructures of the obtained SEBS‐g‐PLA copolymers were also studied. The tensile strength and elongation at break were higher than that of pure SEBS and improved with the increase of grafting degree. In addition, SEBS‐g‐PLA copolymer possessed two‐phase structure with vague phase boundaries. The as‐prepared SEBS‐g‐PLA copolymers can be used as the toughening component to improve the impact strength of PLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of styrene–ethylene/butylene–styrene (SEBS)–clay hybrids

Styrene–ethylene/butylene–styrene triblock copolymer (SEBS)–clay hybrids were prepared by melt blending SEBS and organoclay using an internal mixer. Maleic anhydride modified SEBS (SEBS–MA) was used as a compatibilizer. X‐ray diffraction and transmission electron microscopy revealed that silicate layers of the clay were partially exfoliated and dispersed at a nanometer scale in the polymer matrix. Enhanced mechanical properties of these hybrids were observed from tensile and dynamic mechanical tests. Thermal degradation temperature of the hybrids was increased compared with pristine SEBS. Copyright © 2004 Society of Chemical Industry     

Blending of styrene‐block‐butadiene‐block‐styrene copolymer with sulfonated vinyl aromatic polymers

Different polymers containing sulfonic groups attached to the phenyl rings were prepared by sulfonation of polystyrene (PS) and styrene‐block‐(ethylene‐co‐1‐butene)‐block‐styrene (SEBS). The sulfonation degree (SD) was varied between 1 and 20 mol% of the styrene units. Polyphase materials containing sulfonated units were prepared by blending styrene‐block‐butadiene‐block‐styrene (SBS), with both sulfonated PS and sulfonated SEBS in a Brabender mixer. Such a procedure was performed as an alternative route to direct sulfonation of SBS which is actually not selective towards benzene rings because of the great reactivity of the double bonds in polybutadiene (PB) blocks to sulfonation agents. Thermal and dynamic‐mechanic analysis, together with morphology characterization of the blends, is consistent with obtaining partially compatible blends characterized by higher T_g of the polystyrene domains and improved thermal stability. © 2001 Society of Chemical Industry     

The role of styrene–ethylene/butylene–styrene triblock copolymer as impact modifier in polypropylene–polyethylene blends

The crystallization behavior of an isotactic polypropylene/linear low-density polyethylene blend (PP/LLDPE) that is modified with styrene–ethylene/butylene–styrene triblock copolymer (SEBS) has been investigated using differential thermoanalysis and polarization microscopy. SEBS, which enhances the impact resistance of the blend, has an effect on both the nucleation and crystallization kinetics of the polypropylene component. Nucleation half times, nucleation densities, and spherulite growth rates are influenced by the presence of the copolymer. It is found that SEBS, depending on its concentration in the blend, increases the adhesion between matrix and PE domains and acts simultaneously as the matrix reinforcer. © 1996 John Wiley & Sons, Inc.     

Morphology and mechanical properties of styrene–ethylene/butylene–styrene triblock copolymer/high‐density polyethylene composites

The morphology and mechanical properties of a styrene–ethylene/butylene–styrene triblock copolymer (SEBS) incorporated with high‐density polyethylene (HDPE) particles were investigated. The impact strength and tensile strength of the SEBS matrix obviously increased after the incorporation of the HDPE particles. The microstructure of the SEBS/HDPE blends was observed with scanning electron microscopy and polar optical microscopy, which illustrated that the SEBS/HDPE blends were phase‐separation systems. Dynamic mechanical thermal analysis was also employed to characterize the interaction between SEBS and HDPE. The relationship between the morphology and mechanical properties of the SEBS/HDPE blends was discussed, and the toughening mechanism of rigid organic particles was employed to explain the improvement in the mechanical properties of the SEBS/HDPE blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Physicomechanical and dielectric properties of magnesium and barium ionomers based on sulfonated maleated styrene‐ethylene/butylene‐styrene block copolymer

Ionomers, containing both carboxylate and sulfonate anions on the polymer backbone, based on metal cations like Mg⁺² and Ba⁺² were prepared by sulfonating maleated styrene‐ethylene/butylene‐styrene block copolymer, hereafter referred to as m‐SEBS, followed by its neutralization by metal acetates. Infrared spectroscopic studies reveal that sulfonation reaction takes place in the para position of the benzene rings of polystyrene blocks and metal salts are formed on neutralization of the precursor acids. Dynamic mechanical thermal analyses show that sulfonation causes increase in T_g of the rubbery phase of m‐SEBS and decrease in tan δ at T_g of the hard phase, along with formation of a rubbery plateau. The changes become more pronounced on neutralization of the sulfonated maleated SEBS, and the effect is greater in the case of Ba salt. Dielectric thermal analyses (DETA) show that incorporation of ionic groups causes profound changes in the dielectric constant (ϵ′) of m‐SEBS. In addition to the low temperature glass–rubber transition, the plot of ϵ′ vs. temperature shows occurrence of a high‐temperature transition, also known as the ionic transition. Activation energy for the dielectric relaxation could be determined on the basis of frequency dependence of the ionic transition temperature. Two values of the activation energy for the dielectric relaxation refer to the presence of two types of ionic aggregates, namely multiplets and clusters. Incorporation of the ionic groups causes enhancement in stress–strain properties as well as retention of the properties at elevated temperatures (50° and 75°C), and the effect is more pronounced in the case of Ba ionomer. Although sulfonated ionomers show greater strength than the carboxylated ionomers, the sulfonated maleated ionomers show higher stress–strain properties in comparison to both sulfonated and carboxylated ionomers. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 816–825, 2000     

Compatibilization of polyethylene terephthalate/polypropylene blends with styrene–ethylene/butylene–styrene (SEBS) block copolymers

Blends of polyethylene terephthalate (PET) and polypropylene (PP) at compositions 20/80 and 80/20 were modified with three different styrene–ethylene/butyl–ene-styrene (SEBS) triblock copolymers with the aim of improving the compatibility and in particular the toughness of the blends. The compatibilizers involved an unfunctionalized SEBS and two functionalized grades containing either maleic anhydride (SEBS-g-MAH) or glycidyl methacrylate (SEBS-g-GMA) grafted to the midblock. The effects of the compatibilizers were evaluated by studies on morphology and mechanical, thermal and rheological properties of the blends. The additon of 5 wt % of a SEBS copolymer was found to stabilize the blend morphology and to improve the impact strength. The effect was, however, far more pronounced with the functionalized copolymers. Particularly high toughness combined with rather high stiffness was achieved with SEBS-g-GMA for the PET-rich composition. Addition of the functionalized SEBS copolymers resulted in a finer dispersion of the minor phase and clearly improved interfacial adhesion. Shifts in the glass transition temperature of the PET phase and increase in the melt viscosity of the compatibilized blends indicated enhanced interactions between the discrete PET and PP phases induced by the functionalized compatibilizer, in particular SEBS-g-GMA. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:241–249, 1997     

Melt rheological properties of polypropylene/SEBS (styrene–ethylene butylene–styrene block copolymer) blends

Study of melt rheological properties of the blends of polypropylene (PP) with styrene–ethylene butylene–styrene block copolymer (SEBS), at blending ratios 5–20% SEBS, is reported. Results illustrate the effects of (i) blend composition and (ii) shear rate or shear stress on melt viscosity and melt elasticity and the extrudate distortion. In general, blending of PP with SEBS results in a decrease of its melt viscosity, processing temperatures, and the tendency of extrudate distortion. However, the properties depend on blending ratio. A blending ratio around 5–10% SEBS seems optimum from the point of view of desirable improvement in processability behavior.     

Preparation and properties of styrene–ethylene–butylene–styrene block copolymer/clay nanocomposites: I. Effect of clay content and compatibilizer types

BACKGROUND: Polymer/clay (silicate) systems exhibit great promise for industrial applications due to their ability to display synergistically advanced properties with relatively small amounts of clay loads. The effects of various compatibilizers on styrene–ethylene–butylene–styrene block copolymer (SEBS)/clay nanocomposites with various amounts of clay using a melt mixing process are investigated. RESULTS: SEBS/clay nanocomposites were prepared via melt mixing. Two types of maleated compatibilizers, styrene–ethylene–butylene–styrene block copolymer grafted maleic anhydride (SEBS‐g‐MA) and polypropylene grafted maleic anhydride (PP‐g‐MA), were incorporated to improve the dispersion of various amounts of commercial organoclay (denoted as 20A). Experimental samples were analyzed using X‐ray diffraction and transmission electron microscopy. Thermal stability was enhanced through the addition of clay with or without compatibilizers. The dynamic mechanical properties and rheological properties indicated enhanced interaction for the compatibilized nanocomposites. In particular, the PP‐g‐MA compatibilized system conferred higher tensile strength or Young's modulus than the SEBS‐g‐MA compatibilized system, although SEBS‐g‐MA seemed to further expand the interlayer spacing of the clay compared with PP‐g‐MA. CONCLUSION: These unusual results suggest that the matrix properties and compatibilizer types are crucial factors in attaining the best mechanical property performance at a specific clay content. Copyright © 2007 Society of Chemical Industry     

Preparation and characterization of melt‐blended graphene nanosheets–poly(vinylidene fluoride) nanocomposites with enhanced properties

Nanocomposites of poly(vinylidene fluoride) (PVDF) with chemically reduced graphene nanosheets (GNs) were prepared by melt mixing method and their structure and morphology characterized by SEM analysis. The addition of GNs in the PVDF matrix resulted in changes of the crystallization and melting behaviors. Furthermore, increasing GNs content led to improved thermal stability of the PVDF nanocomposites in air and nitrogen, as well as significant increase in tensile and flexural properties. The nanocomposites' rheological behavior is also affected by the GNs' content. Using oscillatory rheology to monitor the GNs' dispersion, it was found that as the GNs loading increase, the Newtonian behavior disappears at low frequency. This suggests a viscoelastic behavior transition from liquid‐like to solid‐like, with greater GNs content and more homogeneous dispersion resulting in a stronger solid‐like and nonterminal behavior. By using the melt mixing method to disperse GNs, the properties of PVDF are enhanced due to the better dispersion and distribution of GNs throughout the matrix. This improvement could broaden the applications for PVDF nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Modification of styrene–ethylene/butylene–styrene copolymer microstructure by polystyrene homopolymer and evolution of a cocontinuous blend morphology

Styrene–ethylene/butylene–styrene (SEBS) copolymer was blended with the homopolymer polystyrene (hPS) in a counter‐rotating twin‐screw extruder to prepare hPS/SEBS blends. The morphology of the hPS/SEBS blends was studied by environmental scanning electron microscopy (ESEM) and by transmission electron microscopy (TEM). TEM imaging of pure SEBS revealed a microphase‐separated morphology, showing ordered regions or grains where the discrete styrene blocks formed hexagonally packed cylindrical structures within the ethylene/butylene matrix. Blending of small quantities of the homopolymer hPS showed an interesting result. The TEM images of the SEBS‐rich blends revealed that the added hPS was absorbed within the bulk of the SEBS phase resulting in a new SEBS‐rich phase, and the absorbed hPS was found to join the styrene cylinders of pure SEBS thereby modifying its original microstructure. As the hPS concentration in the blends was increased further, the ESEM and TEM images showed that the excess homopolymer hPS phase separated, forming a cocontinuous morphology with the hPS‐modified SEBS‐rich phases. Linear viscoelastic tests on the SEBS‐rich blends also revealed the existence of a synergistic effect, showing increased elastic behavior compared with that of pure SEBS. Small‐angle X‐ray scattering results showed an additional periodicity in the SEBS‐rich phase because of the modification of the SEBS microstructure by hPS. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Mechanical and piezo‐resistive properties of styrene–butadiene–styrene copolymer covalently modified with graphene/styrene–butadiene–styrene composites

As novel piezoelectric materials, carbon‐reinforced polymer composites exhibit excellent piezoelectric properties and flexibility. In this study, we used a styrene–butadiene–styrene triblock copolymer covalently grafted with graphene (SBS‐g‐RGO) to prepare SBS‐g‐RGO/styrene–butadiene–styrene (SBS) composites to enhance the organic solubility of graphene sheets and its dispersion in composites. Once exfoliated from natural graphite, graphene oxide was chemically modified with 1,6‐hexanediamine to functionalize with amino groups (GO–NH₂), and this was followed by reduction with hydrazine [amine‐functionalized graphene oxide (RGO–NH₂)]. SBS‐g‐RGO was finally obtained by the reaction of RGO–NH₂ and maleic anhydride grafted SBS. After that, X‐ray diffraction, X‐ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, and other methods were applied to characterize SBS‐g‐RGO. The results indicate that the SBS molecules were grafted onto the graphene sheets by covalent bonds, and SBS‐g‐RGO was dispersed well. In addition, the mechanical and electrical conductivity properties of the SBS‐g‐RGO/SBS composites showed significant improvements because of the excellent interfacial interactions and homogeneous dispersion of SBS‐g‐RGO in SBS. Moreover, the composites exhibited remarkable piezo resistivity under vertical compression and great repeatability after 10 compression cycles; thus, the composites have the potential to be applied in sensor production. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46568.     

Thermo‐oxidative decomposition kinetics of elastomeric composites based on styrene‐(ethylene‐butylene)‐styrene triblock copolymer and organomontmorillonite

The elastomeric nanocomposites based on organomontmorillonite (OMMT) and styrene‐(ethylene‐butylene)‐styrene (SEBS) thermoplastic elastomer were prepared by melt processing using maleic anhydride grafted SEBS (SEBS‐g‐MA) as compatibilizer. Thermo‐oxidative decomposition behavior of the neat components and the nanocomposites were investigated using thermogravimertic analysis (TGA) in air atmosphere. The isoconversional method is employed to study the kinetics of thermo‐oxidative degradation. The heating modes and the composition of nanocomposites were found to affect the kinetic parameters (E_a, lnA and n). The E_a and lnA values of SEBS, OMMT, and their composites are much higher under dynamic heating than under isothermal heating. The reaction order (n) of OMMT was lower than those of SEBS and their composites. The obtained TG profiles and calculated kinetic parameters indicated that the incorporation of OMMT into SEBS significantly improved the thermal stability both under dynamic heating and under isothermal heating. The simultaneously obtained DSC data showed that the enthalpy of thermal decomposition decreased with OMMT loading. No significant change in the nonisothermal and isothermal stability of the nanocomposites with addition of SEBS‐g‐MA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of polypropylene/acrylonitrile–styrene copolymer alloys by one‐step reactive blending

The compatibilization of polypropylene/acrylonitrile–styrene (PP/AS) blends through the addition of peroxide (DCP) was investigated in this study. The grafting reaction between PP and AS with the addition of peroxide occurred during the reactive‐blending process. The in situ‐formed grafting copolymers of PP‐g‐AS and AS‐g‐PP were then characterized by FTIR. The optimum concentration of the initiator, DCP, was 0.2 wt %, and the reaction temperature should be above 195°C. It was found that, when AS was the major component of the blends, the grafting of AS onto PP was the main process; conversely, when PP was the major component, PP was grafted onto AS. These results can be explained by the main‐chain scission of PP during the reactive‐blending process. With increase of the AS component, the total degree of grafting increased at first and then decreased after the composition of the blends reached 50/50. The maximum degree of grafting was found to be 6 wt % for the 50/50 PP/AS/DCP blend. PP was more degradable than was AS in the presence of peroxide at high temperatures. The MFR values of the PP/AS/DCP blends were slightly greater than were those of the simple PP/AS blends, which means that blending is an effective way to protect PP from degradation. SEM micrographs of the cross section of PP/AS/DCP showed a fine dispersion and a smaller domain size of the dispersed‐phase particles, implying that the in situ‐formed grafting copolymers act as a compatibilizer to reduce the interfacial tension between the PP and AS phases. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1284–1290, 2001     

Influence of addition of styrene–ethylene/butylene–styrene copolymer on rheological,mechanical, and tribological properties of polyamide nanocomposites

To develop new tribomaterials for mechanical sliding parts, investigations were carried out on the influence of adding styrene–ethylene/butylene–styrene block copolymer (SEBS) on the rheological, mechanical, and tribological properties of polyamide 6 (PA6) nanocomposite, which is a commercial product of layered silicate (clay) filled polyamide 6 (PA6/Clay). Two kinds of block copolymers, unmodified SEBS (SEBS) and maleic anhydride‐grafted SEBS (SEBS‐g‐MA), were added with PA6/Clay nanocomposite. Dynamic viscoelastic properties in the molten state of these nanocomposites and their tensile, impact, and tribological properties of these nanocomposites were evaluated. Dynamic viscoelastic properties were found to increase with the addition of SEBS and were influenced, in particular, by block copolymers containing SEBS‐g‐MA. Influence of the addition of SEBS on mechanical properties of these systems differed for each mechanical property. Although tensile properties decreased with SEBS, Izod impact properties were improved with the addition of SEBS‐g‐MA. Tribological properties were improved with the addition of block copolymer, and the influence of the amount of addition was higher than the type of block copolymer used. These results indicate that new tribomaterials developed have sufficient balance amongst moldability, mechanical, and tribological properties. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Grafting of maleic anhydride onto styrene–butadiene–styrene triblock copolymer using supercritical CO2 as a swelling agent

Grafting of maleic anhydride (MA) onto styrene–butadiene–styrene triblock copolymer (SBS) was carried out by free radical polymerization using supercritical carbon dioxide (SC CO₂) as a solvent of MA and swelling agent of SBS. The effect of various factors such as monomer concentration, initiator concentration, SC CO₂ pressure, and reaction time on grafting ratio was studied. SBS and the product (SBS‐g‐MA) were characterized by Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). GPC data showed that the molecular weight of SBS‐g‐MA is bigger than that of SBS. DSC testing indicated that the glass transition temperature (T_g) of SBS‐g‐MA is higher than that of SBS. By SEM photo, we can observe that some particles which contain more oxygen atom grew out from the surface of SBS‐g‐MA when grafting ratio reached at 5.6%, and the amount and diameter of particles increased with increasing of grafting ratio. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4425–4429, 2006     

Behavior of ionomers of sulfonated styrene–butadiene–styrene triblock copolymer in polymer blends with crystalline polyolefins and as compatibilizer

The blends of ionomers of sulfonated (styrene–butadiene–styrene) triblock copolymer with two polyolefins as well as the blends of polystyrene (PSt) with two polar, oil‐resistant elastomers, i.e., chlorohydrin rubber (CHR) and chlorosulfonated polyethylene (CSPE), using the ionomer as compatibilizer were studied. The blends of the ionomer with polypropylene or high density polyethylene showed synergistic effects with respect to tensile strength. With increasing PSt content, the blends change their behavior from thermoplastic elastomer to toughened plastics. The synergism is probably because of the thermoplastic interpenetrating polymer networks formed in the blend. The blends exhibited high resistance against diesel oil or toluene. When PSt was blended with CHR or CSPE using the ionomer as compatibilizer, only 2 or 3% ionomer was needed to enhance the mechanical properties of the blends. The effect is due to the ion–polar interaction of the ionomer with the polar polymer. The enhanced compatibility of the blends by the ionomer was demonstrated by DSC and Scanning electron micrograph. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1887–1894, 2006     

Effects of molecular weight and arm number on properties of star‐shape styrene–butadiene–styrene triblock copolymer

A star‐shape styrene–butadiene–styrene triblock copolymer SBS (802) was synthesized and fractionated into four fractions coded as 802‐F1 (four arms), 802‐F2 (two arms), 802‐F3 (one arm), and 802‐F4 by repeating fractional precipitation. Their weight‐average molecular weight (M_w) was measured by size‐exclusion chromatography combined with laser light scattering to be 16.0 × 10⁴, 8.2 × 10⁴, 4.3 × 10⁴, and 1.19 × 10⁴, respectively. The samples were, respectively, compression‐molded and solution‐cast to obtain the sheets coded as 802C, 802‐F1C, 802‐F2C, and 802S, 802‐F1S, 802‐F2S. The structures and mechanical properties of the sheets were characterized by ¹H‐NMR, scanning electron microscope, wide‐angle X‐ray diffractometer, tensile testing, and dynamic mechanical thermal analysis. The results indicated that the compression‐molded 802‐F1C exhibited the higher tensile strength (σ_b, 28.4 MPa) and elongation at break (ε_b, 1610%), and its optical transmittance is much higher than those of 802C and 802‐F2C. This work revealed that the star‐shape SBS with four arms could be helpful in the enhancement of the properties as a result of good miscibility of the compression‐molded SBS sheets. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 832–840, 2005     

Preparation and properties of PC/SAN alloy modified with styrene‐ethylene‐butylene‐styrene block copolymer

A polycarbonate (PC)/ poly (styrene‐co‐acrylonitrile) (SAN) alloy modified with styrene‐ethylene‐butylene‐styrene (SEBS) block copolymer was prepared and the influence of SEBS content, PC content, and types of modifier on Izod notched impact strength, tensile strength, flexural strength, and Vicat softening temperature was studied. The results showed that the addition of SEBS could obviously increase the Izod notched impact strength and the elongation at break and decrease the tensile and flexural strength and Vicat softening temperature. PC/SAN alloy modified with SEBS had better mechanical properties than the PC/SAN alloy modified with ABS. DSC analysis and SEM photographs revealed that the SEBS was not only distributed in the SAN phase but also distributed in PC phase in a PC/SAN/SEBS alloy while the ABS was mainly distributed in SAN phase in a PC/SAN/ABS alloy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Grafting of N‐carbamyl maleamic acid onto a styrene–butadiene–styrene copolymer

A styrene–butadiene–styrene block copolymer (SBS) was functionalized with N‐carbamyl maleamic acid (NCMA) using two peroxide initiators with the aim of grafting polar groups onto the molecular chains of the polymer. The influence of the concentration of benzoyl peroxide (BPO) and 2,5‐dimethyl, 2,5‐diterbuthylperoxihexane (DBPH) was studied. The concentration of peroxy groups ranged between 0.75 and 6 × 10^?4 mol % while the concentration of NCMA was constant at 1 wt %. The reaction temperature was chosen according to the type of peroxide employed, being 140°C for BPO and 190°C for DBPH. FTIR spectra confirmed that NCMA was grafted onto the SBS macromolecules. It was found that the highest grafting level was achieved at a concentration of peroxy groups of about 3 × 10^?4 mol %. Contact angle measurements were used to characterize the surface of the SBS and modified polymers. The contact angle of water drops decreased with the amount of NCMA grafted from 95°, the one corresponding to the SBS, to about 73°. T‐peel strength of polymer/polyurethane adhesive/polymer joints made with the modified polymers was larger than those prepared with the original SBS. The peel strength of SBS modified with 1.5 and 3 × 10^?4 mol % of peroxy groups from BPO were five times larger than that of the original SBS. The materials modified using BPO showed peel strengths higher than the ones obtained with DBPH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4468–4477, 2006