Natural fiber blend—nylon 6 composites

In this study, engineering thermoplastic composites were prepared from natural fiber blend–filled nylon 6. Natural fiber blend from a mixture of kenaf, flax, and hemp fibers were added to nylon 6 using melt mixing to produce compounded pellets. The natural fibers/ nylon6 composites with varying concentrations of natural fibers (from 5 to 20 wt%) were prepared by injection molding. The tensile and flexural properties of the nylon 6 composites were increased significantly with the addition of the natural fiber blend. The maximum strength and modulus of elasticity for the nylon 6 composites were achieved at a natural fiber blend weight fraction of 20%. The Izod impact strength of composites decreased with the incorporation of natural fibers without any surface treatments and coupling agent. The melt flow index (MFI) also decreased with increasing natural fiber blend loading. The results of tensile and flexural modulus of elasticity (FMOE) are in accordance with the rheological data from the MFI measurements. The increase in the tensile and flexural properties indicated that efficient bonding occurred between the natural fibers and nylon 6. No fiber pullout was observed during the scanning electron microscopic analysis of the fracture surfaces. The higher mechanical results with lower density demonstrate that a natural fiber blend can be used as a sufficient reinforcing material for low‐cost, eco‐friendly composites in the automotive industry and in other applications such as the building and construction industries, packaging, consumer products, etc.POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Biopolyamide hybrid composites for high performance applications

This study focuses on the performance characteristics of wood/short carbon fiber hybrid biopolyamide11 (PA11) composites. The composites were produced by melt‐compounding of the fibers with the polyamide via extrusion and injection molding. The results showed that mechanical properties, such as tensile and flexural strength and modulus of the wood fiber composites were significantly higher than the PA11 and hybridization with carbon fiber further enhanced the performance properties, as well as the thermal resistance of the composites. Compared to wood fiber composites (30% wood fiber), hybridization with carbon fiber (10% wood fiber and 20% carbon fiber) increased the tensile and flexural modulus by 168% and 142%, respectively. Izod impact strength of the hybrid composites exhibited a good improvement compared to wood fiber composites. Thermal properties and resistance to water absorption of the composites were improved by hybridization with carbon fiber. In overall, the study indicated that the developed hybrid composites are promising candidates for high performance applications, where high stiffness and thermal resistance are required. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43595.     

玻璃纤维增强MC尼龙力学性能的研究

用玻璃纤维对MC尼龙复合材料进行改性,研究了玻璃纤维含量及长度对MC尼龙复合材料力学性能的影响。结果表明:玻纤含量50%的MC尼龙同玻纤含量40%的MC尼龙相比,冲击强度、拉伸强度、弯曲强度分别提高29.63%、5.43%,6.47%;MC尼龙复合材料的拉伸强度、弯曲强度及冲击强度随玻璃纤维长度的增长而增加,玻纤的长度越长,MC尼龙复合料力学性能提升效果越好;MC尼龙复合材料弯曲强度与玻纤重均长度为正相关关系,随着玻纤重均长度增大而增大。     

Influence of varying fiber lengths on mechanical,thermal, and morphological properties of MA‐g‐PP compatibilized and chemically modified short pineapple leaf fiber reinforced polypropylene composites

Environmentally benign, low cost and abundantly available short pineapple leaf fibers (PALF), found mostly in the Tropical rain forest climates are ideal materials for manufacture of thermoplastic polymer‐matrix composites. Here, mechanical and thermal properties of composites of maleic anhydride grafted polypropylene (MA‐g‐PP) and chemically modified short PALF are studied as a function of different fiber lengths at 10 vol % fibers loading with fiber orientation in the longitudinal direction. The effects of fiber lengths and fiber loading on the morphological properties are assessed via observations by scanning electron microscopy. Fiber length of 6 mm oriented longitudinally at 10 vol % fibers loading in PP is the optimum and recommended composition, where 73% increase in impact properties, 37% increase in the flexural modulus, 33% increase in flexural strength, and 14% increase in vicat softening temperature are observed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Viscoelastic behavior of epoxy/carbon fiber/Zno nano‐rods hybrid composites

The insufficient viscoelastic resistance of fiber reinforced plastics can be retrofitted by the addition of more rigid nano fillers to the polymer matrix. In this study, carbon fibers plies were grafted with zinc oxide (ZnO) nano‐rods and the hybridized reinforcement was utilized in laminated composites. Flexural creep tests were carried out using dynamic mechanical analysis (DMA) and the time/temperature superposition principle was employed for accelerated testing. To verify the applicability of TTPS, prolonged stress relaxation tests were also carried out in flexural mode. Data from the DMA flexural creep tests revealed that the whiskerization of carbon fibers with ZnO nano rods reduced the creep compliance by 23% at elevated temperatures and prolonged durations. Also, the relaxation data confirmed the applicability of TTPS to these hybrid composites. The stress relaxation modulus improved by 65% in comparison to composites based on neat carbon fibers. POLYM. COMPOS., 36:1967–1972, 2015. © 2014 Society of Plastics Engineer     

Preparation and mechanical characterization of chicken feather/PLA composites

Green composites, a bio‐based polymer matrix is reinforced by natural fibers, are special class of bio‐composites. Interest about green composites is continuously growing because they are environment‐friendly. This study describes the preparation and mechanical characterization of green composites using polylactic acid (PLA) matrix including chicken feather fiber (CFF) as reinforcement. Extrusion and an injection molding process were used to prepare CFF/PLA composites at a controlled temperature range. CFF/PLA composites with fiber mass content of 2%, 5%, and 10% were manufactured. The effects of fiber concentration and fiber length on mechanical properties of CFF/PLA composites have been studied. Mechanical properties of composites were investigated by tensile, compression, bending, hardness, and Izod impact testing. The results of experiments indicated that Young's modulus, compressive strength, flexural modulus, and hardness of the PLA reinforced CFF composites are higher but tensile strength, elongation at break, bending strength and impact strength of them are lower than pure PLA. The results indicate that these types of composites can be used for various applications. POLYM. COMPOS., 38:837–845, 2017. © 2015 Society of Plastics Engineers     

Short‐term flexural creep behavior and model analysis of a glass‐fiber‐reinforced thermoplastic composite leaf spring

Present work investigated the short‐term flexural creep performance of fiber reinforced thermoplastic injection molded leaf springs. Unreinforced polypropylene, 20 wt % short and 20 wt % long glass fiber reinforced polypropylene materials were injection‐molded into constant thickness varying width mono leaf spring. Short‐term flexural creep tests were performed on molded leaf springs at various stress levels with the aid of in‐house developed fixture integrated with the servo‐hydraulic fatigue machine. Spring rate reduction is reported as an index for the accumulated damage. Experimental creep performance of molded leaf springs for 2 h was utilized to predict the creep performance with the aid of four parameter HRZ model and compared with 24‐h experimental creep data. Test results revealed that HRZ model is sufficient enough to predict short‐time flexural creep performance of engineering products over wide range of stress. Test results also confirmed the suitability of long fiber reinforced thermoplastic material for creep application over other considered materials. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of short Grewia optiva fiber‐based polymer composites

Natural fibers, such as Flax, Sisal, Hibiscus Sabdariffa, and Grewia optiva (GO) possess good reinforcing capability when properly compounded with polymers. These fibers are relatively inexpensive, easily available from renewable resources, and possess favorable values of specific strength and specific modulus. The mechanical performance of natural fiber‐reinforced polymers (FRPs) is often limited owing to a weak fiber‐ matrix interface. In contrast, urea–formaldehyde (UF) resins are well known to have a strong adhesion to most cellulose‐containing materials. This article deals with the synthesis of short G. optiva fiber‐reinforced UF polymer matrix‐based composites. G. optiva fiber‐reinforced UF composites processed by compression molding have been studied by evaluating their mechanical, physical, and chemical properties. This work reveals that mechanical properties such as: tensile strength, compressive strength, flexural strength, and wear resistance of the UF matrix increase up to 30% fiber loading and then decreases for higher loading when fibers are incorporated into the polymer matrix. Morphological and thermal studies of the matrix, fiber, and short FRP composites have also been carried out. The swelling, moisture absorbance, chemical resistance, and water uptake behavior of these composites have also been carried out at different intervals. The results obtained lay emphasis on the utilization of these fibers, as potential reinforcing materials in bio‐based polymer composites. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Kenaf‐bast‐fiber‐filled biodegradable poly(butylene succinate) composites: Effects of fiber loading,fiber length,and maleated poly(butylene succinate) on the flexural and impact properties

Poly(butylene succinate) (PBS) filled kenaf bast fiber (KBF) composites were fabricated via compression molding. The effects of KBF loading on the flexural and impact properties of the composites were investigated for fiber loadings of 10–40 wt %. The optimum flexural strength of the composites was achieved at 30 wt % fiber loading. However, the flexural modulus of the composites kept increasing with increasing fiber loading. Increasing the fiber loading led to a drop in the impact strength of about 57.5–73.6%; this was due to the stiff nature of the KBF. The effect of the fiber length (5, 10, 15, and 20 mm) on the flexural and impact properties was investigated for the 30 wt % KBF loaded composites. The composites with 10‐mm KBF showed the highest flexural and impact properties in comparison to the others. The inferior flexural and impact strength of the composites with 15‐ and 20‐mm KBF could be attributed to the relatively longer fibers that underwent fiber attrition during compounding, which consequently led to the deterioration of the fiber. This was proven by analyses of the fiber length, diameter, and aspect ratio. The addition of maleated PBS as a compatibilizer resulted in the enhancement of the composite's flexural and impact properties due to the formation of better fiber–matrix interfacial adhesion. This was proven by scanning electron microscopy observations of the composites' fracture surfaces. The removal of unreacted maleic anhydride and dicumyl peroxide residuals from the compatibilizers led to better fiber–matrix interfacial adhesion and a slightly enhanced composite strength. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Evaluation of multiwalled carbon nanotubes as reinforcement for natural fiber‐based composites

This paper presents the effects of multi‐walled carbon nanotube (MWCNT) as reinforcing agent on some properties of natural fiber/polypropylene composites. In the sample preparation, MWCNT contents and fiber types (bagasse stalk and poplar) were used as variable parameters. The composites with different MWCNT contents were fabricated by melt compounding in a twin‐screw extruder and then by injection molding. The mass ratio of the wood flour to polymer was 40/60 (w/w). The mechanical properties of composites in terms of tensile, flexural, and Izod impact strength were evaluated. The morphology of the specimens was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. Based on the findings of this study, it appears that mechanical properties reached the maximum when 2.5 wt% MWCNT were used. However, addition of 3.5 wt% MWCNT could not enhance the mechanical properties considerably. TEM micrographs showed that at high level of MWCNT loading (3.5 wt%) increased population of MWCNT leads to agglomeration and stress transfer gets blocked. The mechanical properties of composites filled with poplar fibers were generally greater than bagasse stalk composites. POLYM. COMPOS., 37:3269–3274, 2016. © 2015 Society of Plastics Engineers     

Effects of A,B, and S components on fiber length distribution,mechanical, and impact properties of carbon fiber/ABS composites produced by different processing methods

Carbon fiber/ABS composites with different acrylonitrile, butadiene, and styrene components were produced via extrusion/injection and long fiber thermoplastic (LFT)/injection molding processes, respectively. The effect of the components on fiber length distribution, tensile, flexural, impact, and dynamic mechanical properties of the composites was investigated. The properties of carbon fiber/ABS composites produced using 12 mm-long LFT pellets were markedly higher than those produced using extruded pellets made with 12 mm-long chopped carbon fibers. Uses of LFT pellets were preferable to enhancing the mechanical properties of carbon fiber/ABS composites. The tensile, flexural, and dynamic mechanical properties were increased in order of ABS750sw > ABS720 ≥ ABS780 > ABS740, whereas the impact strength was increased in order of ABS740 > ABS780 > ABS720 ≈ ABS750sw. Less carbon fiber damages and less carbon fiber length degradation upon LFT processing resulted in longer fiber length distribution and higher fiber aspect ratio in the composites with LFT pellets, indicating a beneficial reinforcing effect, which was responsible for the increased mechanical properties of ABS composites, particularly with ABS750sw. The results were agreed with each other, significantly depending on the A, B, and S components, being supported by fiber length distribution, fiber aspect ratio, and fracture surfaces.     

Microstructure and fracture behavior of (co)injection‐molded polyamide 6 composites with short glass/carbon fiber hybrid reinforcement

The mechanical and fracture properties of injection molded short glass fiber)/short carbon fiber reinforced polyamide 6 (PA 6) hybrid composites were studied. The short fiber composites of PA 6 glass fiber, carbon fiber, and the hybrid blend were injection molded using a conventional machine whereas the two types of sandwich skin–core hybrids were coinjection molded. The fiber volume fraction for all formulations was fixed at 0.07. The overall composite density, volume, and weight fraction for each formulation was calculated after composite pyrolysis in a furnace at 600°C under nitrogen atmosphere. The tensile, flexural, and single‐edge notch‐bending tests were performed on all formulations. Microstructural characterizations involved the determination of thermal properties, skin–core thickness, and fiber length distributions. The carbon fiber/PA 6 (CF/PA 6) formulation exhibits the highest values for most tests. The sandwich skin‐core hybrid composites exhibit values lower than the CF/PA 6 and hybrid composite blends for the mechanical and fracture tests. The behaviors of all composite formulations are explained in terms of mechanical and fracture properties and its proportion to the composite strength, fiber orientation, interfacial bonding between fibers and matrix, nucleating ability of carbon fibers, and the effects of the skin and core structures. Failure mechanisms of both the matrix and the composites, assessed by fractographic studies in a scanning electron microscope, are discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 957–967, 2005     

Correlation between compounding sequence and the properties of glass fiber‐Reinforced nylon‐6,6 composite

The effects of the compounding sequence and addition of maleic anhydride grafted polypropylene (PP‐g‐MAH) as a sizing agent on the properties of glass fiber (GF)/nylon‐6,6 composite were investigated. Mechanical properties of tensile, impact, and flexural strength were measured. The fractured surface was analyzed to compare the variation of interfacial characteristics by different compounding sequences and addition of a sizing agent. It was found that mechanical and rheological properties of a composite are strongly affected by the compounding sequence and the addition of a sizing agent. In general, the addition of PP‐g‐MAH results in lowering the mechanical properties compared to GF/nylon‐6,6, while proper compounding sequence results in improved mechanical properties. Lowering melt viscosity of composites is achieved by addition of sizing agent and varied depending on the compounding sequence. POLYM. ENG. SCI., 59:155–161, 2019. © 2018 Society of Plastics Engineers     

Mechanical behavior of agro‐residue‐reinforced polypropylene composites

In this research, fully environment‐friendly, sustainable and biodegradable composites were fabricated, using wheat straw and rice husk as reinforcements for thermoplastics, as an alternative to wood fibers. Mechanical properties including tensile, flexural, and impact strength properties were examined as a function of the amount of fiber and coupling agent used. In the sample preparation, three levels of fiber loading (30, 40, and 50 wt %) and two levels of coupling agent content (0 and 2 wt %) were used. As the percentage of fiber loading increased, flexural and tensile properties increased significantly. Notched Izod results showed a decrease in strength as the percentage of fiber increases. With addition of 50% fiber, the impact strengths decreased to 16.3, 14.4, and 16.4 J/m respectively, for wheat straw‐, rice husk‐, and poplar‐filled composites. In general, presence of coupling agent had a great effect on the mechanical strength properties. Wheat straw‐ and rice husk‐filled composites showed an increase in the tensile and flexural properties with the incorporation of the coupling agent. From these results, we can conclude that wheat straw and rice husk fibers can be potentially suitable raw materials for manufacturing biocomposite products. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphological and mechanical behavior of chemically treated jute‐PHBV bio‐nanocomposites reinforced with silane grafted halloysite nanotubes

In this study, at first, thin films of poly(3‐hydroxybutyrate‐co?3‐hydroxyvalerate) (PHBV) nanocomposites were prepared by adding 1–3 wt % grafted halloysite nanotubes (G‐HNTs). Jute‐PHBV bio‐nanocomposites were then fabricated using these films and chemically treated jute fibers in a compression mold machine. The effect of treatment and modification on jute fiber and halloysite nanotubes (HNTs), and the change in their morphology was investigated using Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), scanning and transmission electron microscopy (SEM, TEM). Flexural and thermomechanical properties were determined using a three‐point bend test and dynamic mechanical analysis (DMA). The results showed separation of fiber bundles with rough fiber surfaces, and grafting of silane coupling agents on fibers and HNTs after the chemical treatment. As a result, a strong bonding was established between the PHBV, G‐HNTs and jute fibers that lead to significant improvements in flexural and thermomechanical properties of jute‐PHBV bio‐nanocomposites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43994.     

Fatigue and environmental resistance of polyester and nylon fibers

The fatigue resistance of individual synthetic fibers can govern the performance of complex fiber assemblies such as tire cord and marine rope under certain loading conditions. This paper explores the relative performance of polyester and nylon 6,6 fibers and yarns, both dry and in aqueous solutions, primarily synthetic seawater. Fiber failure over a range of loading conditions and frequencies was found to occur at a critical cumulative strain, governed by a creep rupture process; the cyclic lifetime for both fibers is predictable using a simple creep rupture based theory. Polyester is more resistant to creep rupture, and consequently outperforms nylon 6,6 in cyclic fatigue. The advantage of polyester is considerably greater in aqueous solutions, where the performance of the nylon is diminished. Other comparisons indicate that the particular polyester fibers studied have higher stiffness and strength, lower strain to failure, and much lower hysteresis energy absorption compared with the nylon. The actual fatigue performance of complex fiber assemblies such as ropes is also limited under many conditions by factors not present in single fiber or yarn fatigue, including hysteric heating and internal and external abrasion.     

Palm‐based bio‐composites hybridized with kaolinite

This study described the mechanical and thermal properties of hybrid bio‐composites from oil palm empty fruit bunch (EFB) fibers and kaolinite. The polyurethane (PU) used as matrix is formed by reacting palm kernel oil (PKO)‐based polyester with crude isocyanate. The blending ratio of PU to EFB fibers was fixed at 35 : 65 and kaolinite was added at 0, 5, 10, 15, and 20% (by weight). The occurrence of chemical interactions between the hydroxyl terminals in both fillers and the PU system was determined via FTIR spectroscopy. Hybrid bio‐composites showed improved stiffness, strength, and better water resistance with the addition of kaolinite to an extent. At 15% of kaolinite loading, maximum flexural and impact strengths were observed. The interaction between kaolinite with PU matrix and EFB fibers enhanced the mechanical properties of the bio‐composites, which was justified from the FTIR spectrum. However, over‐packing of kaolinite was observed at 20% kaolinite loading, which ruptured the cellular walls and degraded strength of the bio‐composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Polypropylene/low density polyethylene blends with short glass fibers. II: Effect of compounding method on mechanical properties

Polypropylene/low density polyethylene blend matrices have been reinforced with short glass fibers in order to study their tensile, flexural, and impact behavior. Two-roll milling and twin-screw extrusion compounding methods were used to incorporate the fiber within the polymer matrices, and standard test samples were prepared by injection molding. The effects of matrix composition and fiber concentration on mechanical properties were investigated keeping in mind the matrix and fiber morphology, the latter being intimately dependent upon the compounding method employed.     

Mechanical and thermal properties of waste silk fiber‐reinforced poly(butylene succinate) biocomposites

This article reports the mechanical and thermal properties of poly(butylene succinate) (PBS) biocomposites reinforced with industrially available waste silk fibers, fabricated with varying fiber contents and lengths. The result indicates that use of waste silk fibers may be a potential as reinforcement for effectively improving the static and dynamic mechanical properties of a biodegradable polymer matrix resin, depending on the waste silk fiber content and length in the present biocomposite system. The “as‐separated” waste silk/PBS biocomposites showed the maximum tensile and flexural properties at a fiber loading of 40 wt %, and the “chopped” waste silk/PBS biocomposites showed the optimal strength and modulus with waste silk fibers of 12.7 mm length. The chopped waste silk fibers play a more contributing role in improving the mechanical properties of waste silk/PBS biocomposites than the as‐separated waste silk fibers at a fixed fiber loading. Above the glass transition temperature, the storage modulus of waste silk/PBS biocomposites was significantly greater than that of PBS resin, especially in the higher temperature region. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4972–4980, 2006     

Novel eco‐friendly biodegradable coir‐polyester amide biocomposites: Fabrication and properties evaluation

Biocomposites are prepared from a cheap, renewable natural fiber, coir (coconut fiber) as reinforcement with a biodegradable polyester amide (BAK 1095) matrix. In order to have better fiber‐matrix interaction the fibers are surface modified through alkali treatment, cyanoethylation, bleaching and vinyl grafting. The effects of different fiber surface treatments and fiber amounts on the performance of resulting bio‐composites are investigated. Among all modifications, cyanoethylated coir‐BAK composites show better tensile strength (35.50 MPa) whereas 7% methyl methacrylate grafted coir‐BAK composites show significant improvement in flexural strength (87.36 MPa). The remarkable achievement of the present investigation is that a low strength coir fiber, through optimal surface modifications, on reinforcement with BAK show an encouraging level of mechanical properties. Moreover, the elongation at break of BAK polymer is considerably reduced by the incorporation of coir fibers from nearly 400% (percent elongation of pure BAK) to 16‐24% (coir‐BAK biocomposites). SEM investigations show that surface modifications improve the fiber‐matrix adhesion. From biodegradation studies we find that after 52 days of soil burial, alkali treated and bleached coir‐BAK composites show significant weight loss. More than 70% decrease in flexural strength is observed for alkali treated coir‐BAK composites after 35 days of soil burial. The loss of weight and the decrease of flexural strength of degraded composites are more or less directly related.