Behavior of polyolefin blends with acetylated sisal fibers

The influence of acetylation on the mechanical, thermal and thermodegradative behavior of sisal fiber‐reinforced PP, PP/HDPE and PP/HDPE with functionalized and non‐functionalized EPR composites was studied. Acetylation of the fiber improves adhesion of the fiber to the polyolefin matrix. In general, acetylation of the sisal fiber was found to enhance the tensile strength and modulus of the resulting composites, except in some cases. Thermal properties suggest that the mixing and molding temperatures are between 160 and 230 °C and that when acetylated fiber is mixed with polyolefins, greater polymer‐fiber interactions takes place, which slightly favor stability of these composite materials. The results allow us to suggest that a satisfactory profit/cost relation justifies the addition of acetylated fiber to PP, PP/HDPE, and PP/HDPE/EPR. © 2000 Society of Chemical Industry     

Mechanical properties of plasma-treated sisal fibre-reinforced polypropylene composites

In recent years, sisal fibres have become a promising reinforcement for composites because of their low cost, low density, high specific strength, high specific modulus, easy availability and renewability. However, the poor adhesion between the hydrophilic sisal fibre and the hydrophobic thermoplastic matrices has adversely affected the widespread use of these composites. In this study, argon and air-plasma treatments have been used to modify the fibre surfaces under suitable treatment parameters to improve the compatibility between sisal fibres and polypropylene (PP). Sisal fibres and PP fibres are blended together to form a random mat which is then vacuum hot-pressed into a preimpregnated composite sheet. Mechanical properties such as tensile strength and modulus, flexural strength and modulus, and the storage modulus of the composite sheets improve after the incorporation of plasma-treated fibres. Furthermore, scanning electron microscopy analyses reveal the increased surface roughness of sisal fibre. Surface characterisation has been performed by X-ray photoelectron spectroscopy, showing an increase in oxygen/carbon ratio of sisal fibres after plasma treatment.     

Preparation and characterization of poly(vinyl chloride)/virgin and treated sisal fiber composites

Mechanical property changes, thermal stability, and water absorption capacity of poly(vinyl chloride) (PVC)/sisal fiber composites were assessed with respect to the effect of maleic anhydride chemical treatments of the sisal fiber, for five different sisal fiber contents, varying from 0 to 30% by weight in the composite. The composites prepared with the untreated sisal exhibited higher tensile modulus and hardness than the unloaded resin, while elongation and tensile strength were reduced. The deterioration in the mechanical properties of PVC blended with sisal fiber is attributed to the presence of moisture, interfacial defects at the fiber and polymer interface, and fiber dispersion in the PVC matrix. The amount of absorbed water is a function of the amount of fiber in the composite (F0 = 0 phr, F5 = 0.77 phr, and F20 = 4.83 phr). The comparison of the results of characterization of F5, F20, and F30 formulations prepared with the untreated fibers and the treated ones showed a reduction in absorbed water after the chemical treatment of fiber with maleic anhydride (F0 = 0 phr, F5 = 0.28 phr, and F20 = 2.99 phr), thus improving the mechanical properties of composites prepared with the treated sisal. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3630–3636, 2007     

Role of Cenosphere Addition on Dielectric Properties of Sisal Fiber-Polypropylene Composites

This research investigates the influence of addition of porous additives on dielectric constant of polypropylene. Composite composed of PP matrix with sisal fiber having cylindrical pores and cenospheres having spherical pore, presents low dielectric constant. A new relation concerning porosity is proposed by modifying the usual mixing rule to predict the dielectric constant of PP composite. This research presents the dielectric properties of sisal fiber-reinforced PP composites with and with out cenospheres. Treated and untreated cenospheres with different concentration were loaded in chopped sisal fiber-reinforced polypropylene. The loading of the polypropylene with the sisal fiber, increases the dielectric constant ε′ and improves the ac conductivity σ_ac. The effect of temperature on the dielectric spectrum of polypropylene composites was investigated in the frequency range ranging from 1–10 kHz. Sisal fiber-reinforced polypropylene composites having 20% sisal fiber with and without cenospheres were developed and electrical properties such as dielectric constant (?′), dissipation factor (tanδ) and ac conductivity (σ_ac) of these composites were determined. Dielectric constant, tan δ, and a.c. conductivity increases with increase in temperature at different frequencies.     

Mechanical properties of short sisal fiber‐reinforced polypropylene composites: Comparison of experimental data with theoretical predictions

Sisal fibers were used for the reinforcement of a polypropylene (pp) matrix. Composites consisting of polypropylene reinforced with short sisal fibers were prepared by melt‐mixing and solution‐mixing methods. A large amount of fiber breakage was observed during melt mixing. The fiber breakage analysis during composite preparation by melt mixing was carried out using optical microscopy. A polynomial equation was used to model the fiber‐length distribution during melt mixing. The experimental mechanical properties of sisal/PP composites were compared with existing theoretical models such as the modified rule of mixtures, parallel and series models, the Hirsch model, and the Bowyer–Baders model. The dependence of the tensile strength on the angle of measurement with respect to fiber orientation also was modeled. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 602–611, 2003     

剑麻纤维与晶须混杂增强聚丙烯复合材料

采用熔融共混和注塑成型方法制得了剑麻短纤维(SF)和CaSO4晶须混杂增强聚丙烯(PP)复合材料，研究了复合材料的热性能、微观结构和力学性能。结果表明，晶须提高了复合材料的热稳定性，阻碍了PP的结晶，降低了复合材料中PP相的结晶度和结晶速率；SF和晶须提高了复合材料的模量和韧性，但由于混杂增强复合材料弱界面键合的制约，晶须的高强性能并没有在复合材料中充分表现出来。     

Immersion Temperature Effects on the Water Absorption Behavior of Hybrid Lignocellulosic Fiber Reinforced-Polyester Matrix Composites

Although economic, ecological, processing and property considerations suggest that it is very attractive to use lignocellulosic fibers as reinforcement in polymer matrix composites, moisture can strongly and deleteriously affect their properties. In this work the water absorption behavior of sisal/cotton, jute/cotton and ramie/cotton hybrid fabric reinforced composites is evaluated. The effect of the temperature of immersion, fiber volume fraction, and predrying of the fabrics before their incorporation onto the composites are evaluated. Sisal was shown to be the most hygroscopic of the fibers analyzed, and its presence leads to higher values of the maximum water content and of the diffusion coefficient of sisal/cotton reinforced composites. Under the range of temperatures analyzed (30–60°C) the volume fraction of the fibers, rather than the temperature itself, was shown to be the main parameter governing water absorption. Predrying usually lowers maximum water content, although for sisal/cotton reinforced composites a reverse trend was observed for the composites with higher volume fractions. This behavior was again attributed to the higher hydrophilic behavior of sisal fibers.     

Viscoelastic and thermal properties of woven‐sisal‐fabric‐reinforced natural‐rubber biocomposites

Textile–rubber biocomposites were prepared by the reinforcement of natural rubber with woven sisal fabric. The viscoelastic properties of the composites were analyzed at different frequencies. Sisal fabric was subjected to different chemical modifications, such as mercerization, silanation, and thermal treatment, and the influences of the modifications on the dynamic mechanical properties were analyzed. The storage modulus was found to increase with reinforcement of natural rubber with woven sisal fabric. The chemical modification of the sisal fabric resulted in a decrease in the storage modulus. The damping factor was found to decrease with chemical treatment, and the gum compound exhibited maximum damping characteristics. The thermal stabilities of the composites were also analyzed by thermogravimetric studies. Scanning electron microscopy studies were performed to evaluate the morphology of the fabric–matrix interface.© 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Reinforcement of polypropylene using sisal fibers grafted with poly(methyl methacrylate)

Sisal fiber (SF) surface modification was carried out by grafting with methyl methacrylate (MMA) using cerium and ammonium nitrate as initiator. The effects of reaction time, monomer, and initiator concentration on the grafting parameters were systematically investigated. The results showed that MMA was successfully grafted onto the sisal fiber surface. The PMMA‐grafted sisal fibers were melt blended with polypropylene (PP) and then injection molded. The PP/SF composites were characterized by means of thermal analysis, mechanical testing, wide‐angle X‐ray diffraction, and SEM examination. PMMA grafted onto the surface of SF enhanced the intermolecular interaction between the reinforcing SF and PP matrix, improved the dispersion of SF in the PP matrix, and promoted the formation of β‐crystalline PP. These enhanced the thermal stability and mechanical properties of PP/SF composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1055–1064, 2003     

Oxygen plasma treatment of sisal fibers and polypropylene: Effects on mechanical properties of composites

Polypropylene powder and sisal fibers were oxygen plasma treated, and the mechanical properties of their composites were tested. Two main effects were investigated: the incorporation of oxygen polar groups in the polypropylene surface and the surface degradation and chain scission of both polypropylene and sisal fibers. Prior to these treatments, three reactor configurations were tested to investigate the best condition for both effects to occur in PP films. Results showed that polypropylene‐cellulose adhesion forces are about an order of magnitude higher for PP film treatments at 13.56 MHz than at 40 kHz owing to much higher chain scission at lower frequencies, although it probably also occurs at high frequency and high power. Polypropylene powder treated with oxygen plasmas in optimum conditions for polar group incorporation did not result in improvement in any composite mechanical property, probably owing to the polymer melting. Sisal fibers and PP powder treated in conditions of surface degradation did not improve flexural or tensile properties but resulted in higher impact resistance, comparable to the improvement obtained with the addition of compatibilizer.     

剑麻纤维增强聚丙烯复合材料的冲击特性研究

采用片状层压工艺制备了短切剑麻纤维(SF)／聚丙烯(PP)复合材料，用高级仪器化摆锤冲击试验机对复合材料的冲击过程进行了全面分析，并借助扫描电子显微镜对复合材料的冲击破坏断口进行观察。结果表明：当SF的长度为20mm、wpp=30％时，SF对PP的增韧效果最好。采用短切SF增强PP基体，可使复合材料断裂过程吸收的能量增加，裂纹扩展缓慢，断裂后期吸收能量增大。     

Development of heating elements based on conductive polymer composites for electrofusion welding of plastics

Conductive polymer composites have been developed based on high-density polyethylene filled with carbon black (HDPE-CB), capable of generating heat when an electric voltage is applied. For each voltage value, the composite reached a constant value of equilibrium temperature, which obeyed a quadratic dependence on voltage and a linear dependence on electric power. The possibility of using such composites as heating elements (HE) for electrofusion welding of polyethylene adherents was evaluated in two modes, ''hard'', when high voltage was applied for a short welding time, and ''soft'', in which a stepwise regime of the applied voltage and a longer welding time were used. The latter provided a stronger welded joint. Using HE based on the HDPE-CB composites for welding of butt and lap joints of the polymer materials enabled to obtain welded joints with high strength.     

管材用回收高密度聚乙烯/胶粉复合材料的研究

采用一步法活化增容制备了回收高密度聚乙(烯RHDPE/)胶粉管材专用料,并研究了引发剂过氧化二异丙苯强度从37.5 kJ/m2提高到48 kJ/m2;弯曲强度从10.5 MPa提高到12.9 MPa;弯曲模量从356 MPa提高到405(DCP)、接枝单体马来酸酐(MAH用)量对体系力学性能的影响。结果表明:当DCP、MAH用量分别为0.1份、1.0份时,RHDPE/胶粉体系获得最佳的力学性能,与简单共混物比较,拉伸强度从18.8 MPa提高到23.8 MPa;缺口冲击MPa。通过流变性能测试结果和扫描电(镜SEM)照片分析活,化增容对RHDPE/胶粉体系有效。     

Recycled‐disposable‐chopstick‐fiber‐reinforced polypropylene green composites

The utilization of disposable chopsticks is very popular in Taiwan, China, and Japan and is one of the major sources of waste in these countries. In this study, recycled disposable chopstick fiber was chemically modified. Subsequently, this modified fiber and polypropylene‐graft‐maleic anhydride were added to polypropylene (PP) to form novel fiber‐reinforced green composites. A heat‐deflection temperature (HDT) test showed an increase of approximately 81% for PP with the addition of 60‐phr fibers, and the HDT of the composite could reach up to 144.8°C. In addition, the tensile strength, Young's modulus, and impact strength were 66, 160.3, and 97.1%, respectively, when the composite material was 40‐phr fibers. Furthermore, this type of reinforced PP would be more environmentally friendly than an artificial‐additive‐reinforced one. It could also effectively reduce and reuse the waste of disposable chopsticks and lower the costs of the materials. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Plant oil‐based biofoam composites with balanced performance

BACKGROUND: Biofoam composites were prepared using short sisal fibers as reinforcement and acrylated epoxidized soybean oil as matrix, aiming at replacing traditional unsaturated polyester foams in structural applications. The compressive properties of the composites were examined as a function of fiber loading, fiber length and foam density. RESULTS: The foam composite with 10 phr (parts per hundred of base resin by weight) sisal fiber possessed properties similar to those of commercial unsaturated polyester foams. A study of the failure mechanism revealed that debonding between fiber and matrix was a key issue responsible for catastrophic damage of the composites. According to this finding, surface pre‐treatment of the sisal using an alkali or silane coupling agent was carried out. This brought about positive effects on interfacial interaction and compressive strength of the composites, as desired. Also, soil burial tests proved that the foam composites could be biodegraded, and the incorporated sisal fibers accelerated the biodegradation of the composites. CONCLUSION: This work shows the feasibility of making rigid biofoams from natural resources, which could be potential candidates for structural foams. Copyright © 2009 Society of Chemical Industry     

Polylactic acid (PLA)/banana fiber (BF) biodegradable green composites

In this study, polylactic acid (PLA)/banana fiber (BF) composites were prepared by melt blending method. The BF was conjugated onto PLA chains through the use of a coupling agent and chemical modification. Consequently, the thermal stability and mechanical properties of the PLA were dramatically elevated through the incorporation of BF. Mechanical tests showed that the tensile and flexural strengths of the composites markedly increased with the fiber content, reaching 78.6 and 65.4 MPa when reinforced with 40 phr fiber, approximately 2 and 1.66 times higher, produced by pristine PLA. However, the impact strengths of composites are somewhat decreased with the increased content of fibers. The addition of 40 phr BF into the composite increased the HDT of pure PLA from 62 °C to 139 °C; an improvement of about 122%. Apart from enhancing the mechanical properties and thermal stability, the incorporation of BF can reduce the production cost of materials while meeting the demands of environmental protection agencies.     

Moisture durability of four moisture cure urethane adhesives

Moisture durability of four low modulus adhesives was examined. The four low modulus adhesives all had the same basic moisture cure polymer but contained different fillers and additives. Hot-dipped galvanized steel was bonded to random fiber-reinforced unsaturated polyester and aged in two moisture environments for various durations. Adherend surface wipes included acetone, isopropyl alcohol and a typical surface contamination for galvanized steel (an organic lubricant). Diffusion coefficients, moisture uptake and modulus changes due to moisture environment were determined for the adhesives and the fiber-reinforced plastic (FRP). The moisture cure adhesive with clay and poly(vinyl chloride) (PVC) as fillers (adhesive 252) had the highest retained lap joint strengths. Initially, adhesive 252 had single lap joint strengths of 1.47 ± 0.08 MPa for acetone-wiped joints and 1.39 ± 0.33 MPa for organic lubricant-wiped joints. After accelerated aging in a cataplasma environment for 9 weeks, lap joint strengths fell to 0.61 ± 0.08 MPa for acetone-wiped joints and to 0.65 ± 0.11 MPa for organic lubricant-wiped joints. Environmental scanning electron microscopy (ESEM) and energy-dispersive spectrometry (EDS) showed that the actual failure locus was through a corroded zinc layer and between the adhesive and the zinc surface after aging. Dynamic mechanical analysis (DMA) showed that the modulus for adhesive 252 dropped from 21.7 to 13.9 MPa after cataplasma aging. From finite element analysis (FEA), this modulus drop corresponded to a drop in normal stress concentration from 0.75 to 0.57, and a drop in shear stress concentration from 1.41 to 1.36 at a point 0.5 mm from the end of the single lap joint overlap.     

POE/HDPE/PP三元复合材料的形貌和力学性能研究

用熔融共混法制备了高密度聚乙烯/聚丙烯(HDPE/PP)和乙烯-辛烯弹性体/高密度聚乙烯/聚丙烯(POE/HDPE/PP)复合材料。通过冲击、弯曲和拉伸测试研究了复合材料的力学性能,采用扫描电镜(SEM)观察了材料的形貌。结果表明,由于HDPE和PP的相容性有限,限制了HDPE对PP综合力学性能的提高;通过添加POE,能改善HDPE/PP共混物的相容性,使HDPE/PP复合材料在保持较高弯曲和拉伸性能的前提下,抗冲击性能获得明显提高。当HDPE/PP的含量比为12/88和POE含量为8wt%时,POE/HDPE/PP三元复合材料的综合力学性能较好。     

Mechanical and thermal properties of exfoliated graphite nanoplatelets reinforced polyethylene terephthalate/polypropylene composites

Exfoliated graphite nanoplatelets (GNP) reinforced composites materials based on blend of poly(ethylene terephthalate) (PET) and polypropylene (PP) were prepared by melt extrusion followed by injection molding. 10 parts per hundred resin (phr) styrene‐ethylene‐butylene‐styrene‐g‐maleic anhydride was added to the base formulation PET/PP (70/30) as a compatibilizer. PET/PP/GNP composites 0–5 phr were prepared and characterized using field emission scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, and Fourier transform infrared (FTIR) spectroscopy analysis. The morphological studies revealed a homogenous dispersion of GNPs in PET/PP blends up to 3 phr loading after which agglomeration occurred. Flexural strength was enhanced by 80% at 3 phr GNPs loading which was the highest value obtained. Interestingly, the highest value for the impact strength was also recorded at 3 phr loading. The thermal stability of the composites were generally improved at all filler loading with the highest at 3 phr. From the overall results, it is clear that the optimum concentration of GNPs in the PET/PP/GNP system in terms of both mechanical and thermal properties was 3 phr loading. Although, the mechanical and thermal properties of the composites were improved, the FTIR analysis did not reveal any chemical interaction between GNP and the polymer matrix. POLYM. COMPOS., 35:2029–2035, 2014. © 2014 Society of Plastics Engineers     

PP/HDPE/EPDM共混物的研究

研究了聚丙烯（ＰＰ）、高密度聚乙烯（ＨＤＰＥ）和ＥＰＤＭ共混制备非交联型ＰＰ／ＨＤＰＥ／ＥＰＤＭ三元共混物。结果表明，当共混比ＰＰ／ＨＤＰＥ／ＥＰＤＭ＝６５／２０／１５，活性碳酸钙为３０份，ＨＤＰＥ品种为ＧＦ７７５０，采用先把ＨＤＰＥ和ＥＰＤＭ预制成混料再与ＰＰ共混的方法，可得到性能良好的ＰＰ／ＨＤＰＥ／ＥＰＤＭ共混物。