Effect of laser textured dimples on the lubrication performance of cylinder liner in diesel engine

Laser surface texturing (LST) technique was utilised on a cylinder liner in a diesel engine. In order to analyse the effect of LST micro‐dimples on the lubrication and friction properties of cylinder liner–piston ring (CL–PR), we developed a new mixed lubrication model on the basis of the average Reynolds equation and asperity contacts equation. The model can consider the coupling effects between the surface roughness of non‐texturing regions and micro‐dimples and the synergistic effects of multi‐micro‐dimples. The results show that cylinder liner surface by LST can form effective hydrodynamic lubrication effect in most regions of the strokes, only near the dead points, the friction pair is in mixed lubrication state, asperity contact plays a major role in balancing the external load and the asperity friction force is obvious. The micro‐dimple parameters were optimised to obtain a better lubrication effect with the following optimised results: r_p = 30–60 µm, S_p = 0.2–0.4 and e = 0.03–0.1. Copyright © 2012 John Wiley & Sons, Ltd.     

Significance of Dimple Parameters on the Friction of Sliding Surfaces Investigated by Orthogonal Experiments

Surface texturing has proven to be an effective method to improve tribological performance of sliding surfaces. The pattern of microdimples is the most popular surface texture because it is supposed to obtain additional hydrodynamic pressure easily.

In order to evaluate the significance of the dimple parameters, including dimple diameter, depth, and area ratio, to the frictional performance, the dimple patterns with dimple diameter from 50 to 300 μm, dimple depth from 5 to 20 μm, and area ratio from 5 to 20% were manufactured on chromium-coated specimens by through-mask electrochemical micromachining. Experiments were designed using an L ₁₆ (4 ⁵ ) orthogonal array, which contained the above three factors and four levels for each factor. The frictional tests on the above-textured specimens against the specimens of cast iron with oil lubrication were carried out under the contact pressures of 0.2 and 1 MPa and sliding velocities of 0.1 s and 0.5 m/s.

The range analysis showed that the optimum dimple pattern was that with dimple diameter of 100–200 μm, dimple depth of 5–10 μm, and area ratio of 5%, which induced the friction reduction up to 77.6% compared to that of untextured surfaces.

Both the range analysis and analysis of variance suggested that dimple area ratio is the most important parameter influencing friction coefficient under the test condition of this research.     

Use of the Roughness Parameters Ssk and Sku to Control Friction—A Method for Designing Surface Texturing

The aim of this work was to show that with the use of the surface roughness parameters S_sk and S_ku we can predict tribological behavior of contact surfaces and use these parameters to plan surface texturing. This article presents a continuation of our research on virtual texturing and experimental work on surface textures in the form of channels. For this investigation, steel samples were laser surface textured in the shape of dimples with different spacings between the dimples and different dimple depths. The experimental results confirmed that the parameters S_sk and S_ku can be used to design the surface texturing, where a higher value of S_ku and more negative S_sk lead to lower friction.     

缸套表面织构润滑性能理论及试验研究

通过将激光表面织构技术应用于发动机缸套表面,建立缸套-活塞环摩擦副混合润滑理论模型,并以桶面环为例,计算缸套表面织构对摩擦副润滑摩擦性能的影响规律。计算结果表明：缸套通过激光表面织构后,其润滑摩擦性能得到改善,凹腔织构效果要优于沟槽织构效果,在各行程中部油膜厚度最大增加了29%左右,而摩擦力峰值下降30%左右。通过发动机对比台架试验发现：相对于原机,配套表面织构缸套后发动机燃油消耗率呈现出下降趋势,在低转速下改善效果最为显著,燃油消耗率最大降低了9.8 g/(kW•h),降幅为4.62%,证实了表面织构技术对于降低发动机摩擦损失是有效的;同时发动机的其他性能指标也有不同程度改善,漏气量、烟度、全损耗系统用油消耗率等参数都有所下降,烟度下降明显,漏气量最大降幅为34.6%,全损耗系统用油消耗率降低了33.8%。     

Preliminary investigation of the effect of dimple size on friction in line contacts

The scale of surface texture is becoming an important issue of surface texture design, particularly for the condition of low speed and high load. Experiments were carried out to investigate the effect of dimple size on friction under line contact condition. The patterns of dimples distributed as square array were fabricated on the surface of brass disks. Each pattern has the same area density of 7%, the same depth over diameter ratio h/d of 0.03, and dimple diameter d varying from 20 to 60 μm. The frictional tests of the brass disk sliding against a stationary cylindrical surface of bearing roller were conducted. It was found that the pattern with dimple diameter of 20 μm presented the effect of friction reduction. For the further understanding of the effect of dimple size under line contact condition, numerical simulations were also carried out to evaluate the hydrodynamic pressure within the contact of cylindrical and plane surfaces. The effects of dimple size and radius of the cylinder on the load carrying capacity were evaluated and discussed.     

Fabrication and tribological behaviors of corner-cube-like dimple arrays produced by laser surface texturing on medical needles

Micro-corner-cube-like dimples with various geometrical characteristics were fabricated on the surface of medical needles by laser surface texturing. The effects of geometric parameters of dimples on tribological behaviors were investigated by carrying out insertion tests. It was found that the textured surface with a dimple array increased the friction between the needle and phantom tissue because of stress concentrations near the edges. Furthermore, the drag increment rate increased with the increase of dimple size and circumferential number, while dimple depth had no significant effect on the friction. The minimal drag increment rate was achieved at a medium value of spacing. The geometric parameters of dimples could be varied to control area density that indirectly affect the friction behavior.     

Texture shape effects on hydrodynamic journal bearing performances using mass-conserving numerical approach

ABSTRACT

It is a known fact that incorporating textures in the contact surfaces can significantly enhance bearing performances. The purpose of this paper is to outline the effects of texture bottom profiles and contour geometries on the performances of hydrodynamic textured journal bearings. The analysis was conducted using computational approach to test eight texture shapes: rectangular, cylindrical, spherical, triangular (TR, T1, T2, T3) and chevron. The steady-state Reynolds equation for modelling the hydrodynamic behaviour of thin viscous film was solved using finite difference technique and mass conservation algorithm (JFO boundary conditions), taking into account the presence of textures on both full film and cavitation regions. The comparison with the benchmark data shows good consistency and an enhancement in bearing performances (load carrying capacity and friction). The results clearly show that the mechanisms of wedge effect and micro-step bearing for the full/partial texturing feature are the main crucial parameters, where the convergent wedge effect present in T2 triangular texture shape can significantly enhance the load-carrying capacity, while the divergent wedge action causes a net load loss. Considering the right arrangement of textures on the contact surface, their surface contours can have a significant impact on the performance of hydrodynamic journal bearings at high eccentricity ratios.     

Experimental Investigation of Partial Laser Surface Texturing for Piston-Ring Friction Reduction

An experimental study is presented to evaluate the effect of partial laser surface texturing (LST) on friction reduction in piston rings. In a previous study, 30% friction reduction was obtained with full LST where the full width of the piston ring is textured with a very large number of microdimples that act individually as microhydrodynamic bearings. In partial LST, only a portion of the piston-ring width is textured with high dimple density, producing a “collective” effect of the dimples that provides an equivalent converging clearance even with nominally parallel mating surfaces. Experimental results obtained with flat and parallel test specimens with partial LST are presented, confirming a previously published theoretical model and the advantage of partial over full LST. Friction reduction by LST with actual production-crowned piston rings and cylinder liner segments is not straightforward and needs further investigation.     

基于摩擦学的表面织构技术应用研究进展

表面织构是在摩擦面上加工出具有一定尺寸和排列的凹坑或微小沟槽的点阵,可有效改善表面摩擦学性能。本文介绍了表面织构的几何参数和加工方法,总结了表面织构技术在机械部件、材料加工、磁存储设备、摩擦制动等方面的研究进展,展望了未来表面织构技术可能的发展方向。     

Abrasive wear resistance of textured steel rings

The fundamental aim of the present research is to study the effect of dimple shape and area density on abrasive wear in lubricated sliding. The other aims are to recommend a method of obtaining the local linear wear of a textured ring on the basis of profilometric measurement and to analyse the changes in the surface topography of this ring with selection of parameters that could monitor the “zero-wear” process.The experiments were conducted on a block-on ring tester. The stationary block made from cast iron of 50 HRC hardness was ground. The rotated ground ring was made from 42CrMO4 steel of 32 HRC hardness. The rings were modified by a burnishing technique in order to obtain surfaces with oil pockets. Oil pockets of spherical and of drop shape were tested. The pit-area ratios were in the range: 7.5–20%. The tested assembly was lubricated by oil L-AN 46. Because of the great hardness of the co-acting parts the wear resistance test was carried out under artificially increased dustiness conditions. The dust consists mainly of SiO₂ and Al₂O₃ particles. Measurement of local microscopic ring wear was made using a three-dimensional scanning instrument. The tendencies of ring surface topography changes during wear were analysed. Various methods of obtaining the local wear value during a low wear process were proposed and compared. We found that a spherical shape of dimples was superior to a drop shape with regard to wear resistance of steel rings.     

Effects of laser surface texturing on friction behavior of silicon nitride under lubrication with water

Water lubrication is one of the candidates of the tribo-system with low negative environmental impact. It is well known that some kinds of ceramics show excellent tribological properties under lubrication with water. The characteristic improvement was attempted by giving texturing to Si₃N₄ so that the water lubrication might spread as a representative of the ecotribology system. The surface laser texturing showed the friction reducing effect under the sliding condition of the low bearing characteristic number. The mechanism of the triblogical property improvement by the laser surface texturing was discussed based on the experiment results and the surface analytical results.     

Effect of Hardness Ratio on the Wear Performance and Subsurface Evolution of Ni3Al Matrix Composites

A favorable hardness ratio (H_disk/H_pin = H_d/H_p) could lead to a transition to mild wear during sliding contact. To determine a more appropriate H_d/H_p value for the sliding wear, the dry sliding pin-on-disk wear tests of Ni₃Al matrix composites (NMCs) with multilayer graphene (MLG) are undertaken at H_d/H_p values of 0.99, 0.83, 0.42, and 0.35 at sliding speeds of 0.1, 0.3, 0.5, and 0.7 m/s. It is found that the tribological properties of NMCs are strongly affected by the various hardness ratios. At 0.1 m/s, the friction coefficient decreases with a decrease in H_d/H_p value. The low friction coefficient is 0.14 and the wear rate is 0.9 × 10^?5 mm³ N^?1m^?1 under the ceramic counterpart with H_d/H_p of 0.35. At 0.7 m/s, the tribological properties show the opposite trend with a decrease in H_d/H_p. At an H_d/H_p of 0.35, the smooth compact layer on the worn surface could decrease the friction at 0.1 m/s, and the improved hardness in the subsurface by strain hardening would play an important role in the improvement of wear resistance. Under the metal counterpart with H_d/H_p of 0.99, plastic deformation only occurs on the contact surface and the MLG could suppress further shear deformation in the subsurface, leading to a low wear rate (2.4 × 10^?5 mm³ N^?1m^?1) and friction coefficient (0.15) at 0.7 m/s.     

凹坑织构对石墨材料水润滑性能的影响

为提高核主泵屏蔽电机用水润滑石墨轴承的摩擦润滑性能,采用高速雕铣机在石墨试样表面加工不同形状、深度和面积占有率的凹坑织构,通过水润滑条件下的销盘摩擦试验,测试分析凹坑织构结构参数对石墨材料水润滑性能的影响。结果表明：在水润滑条件下凹坑织构具有一定的减摩效果,随着转速的增加,凹坑织构的动压效应增强,石墨试样摩擦因数减小;随着载荷的增加,石墨试样摩擦因数减小;随着凹坑深径比、面积占有率的增加,石墨试样摩擦因数均呈现先减小后增大的变化趋势,当凹坑深径比为0.5、凹坑面积占有率为3%左右时,石墨试样摩擦因数最小;相较三角形凹坑织构,正方形凹坑和圆形凹坑织构的减摩效果更好。     

Ionic liquids as lubricants of polystyrene and polyamide 6-steel contacts. Preparation and properties of new polymer-ionic liquid dispersions

Room-temperature ionic liquids (ILs) have been used as external lubricants in polystyrene (PS) and polyamide 6 (PA6)-steel contacts and as internal lubricants in new polymer-IL dispersions. 1−C _n H_2n+1−3−CH₃-imidazolium X⁻ [X=BF₄; n=2 (IL1), 6 (IL2), 8 (IL3). X=PF₆; n=6 (IL4). X=CF₃SO₃; n=2 (IL5). X=(4−CH₃C₆H₄SO₃); n=2 (IL6)] ionic liquids give low friction and extremely mild wear in PS/AISI 316L stainless steel contacts, independently of IL composition. For AISI 52100 steel pins a tribocorrosion reaction produces FeF₂ and increases friction. PS+IL1 (1; 1.35; 3 wt.% IL1) dispersions show lower dry friction and wear against AISI 52100 as IL1 proportion increases, but the lowest friction, with a one order of magnitude reduction with respect to PS, is reached for PS+1%IL1 once the skin layer has been worn out. Increasing IL1 content to 10 wt.% produces an heterogeneous material with non-uniform IL distribution. IL4 reduces friction and wear in PA6+3%IL4 dispersions against AISI 316L, although the lowest values are obtained with IL4 as external lubricant. The cryofracture surfaces of the polymers have been examined and the thermal stability of the polymers in the presence of ILs has been determined.     

Investigation on Dimples Distribution Angle in Laser Texturing of Cylinder–Piston Ring System

The effectiveness of laser surface texturing in reducing wear rate was studied, with emphasis on dimple distribution angle. Experiments were performed by varying the texturing parameters to derive variational rulesof the wear scar depth on laser-textured cylinder walls under starved lubrication conditions, and the optimum laser texturing dimple distribution angle was obtained. It was found that the laser texturing could result in less wear rate compared to mechanical honing.     

Friction and Wear Properties of MoS<Subscript>2</Subscript>-Overcoated Laser Surface-Textured Silver-Containing Nickel-Based Alloy at Elevated Temperatures

The solid lubricant that is coated on a flat surface is easily removed during friction. Surface texture dimples, which act as reservoirs of solid lubricant, can prolong the wear life of solid lubricant films. We textured silver-containing nickel-based alloys by a pulse laser and filled the micro-dimples with molybdenum disulfide powders. The tribological properties of the alloys were tested by rubbing against alloyed steel on a ring-on-disk tribometer at temperatures ranging from room temperature to 600°C . After laser surface texturing, the friction coefficients of the silver-containing nickel-based alloy smeared with molybdenum disulfide powders were reduced at temperatures ranging from room temperature to 400°C. With increasing dimple density, the wear life of the MoS₂ film increased while the wear rate of the nickel-based alloy decreased. The wear life of the textured surface with a dimple density of 11.2% exceeded 10,000 m at room temperature. We conclude that molybdenum disulfide and its oxides stored in the micro-dimples play a role in lubrication at room temperature and high temperatures, respectively.     

Comparison of the effects of surface texture on the surfaces of steel and UHMWPE

Surface texture has been well studied for metals and ceramics. For the tribo-pair consisted of soft and stiff materials, in order to find out which side is better for texturing, friction tests between steel and UHMWPE were performed to evaluate the effect of dimple patterns at different load–speed conditions.At a light load of 100 N, surface texture on either steel or UHMWPE can reduce friction, but their optimum area densities are different. However, at a heavy load of 700 N, only the pattern textured on UHMWPE can effectively reduce friction. Test results are further analyzed in terms of contact stress.     

平行滑块表面矩形-半球型复合织构润滑性能研究*

研究仿生硅藻的多级孔结构——矩形与半球型结合的复合型织构对平行滑块润滑性能的影响。通过建立矩形-半球型的复合型织构单个单元模型,采用双向流固耦合的方法,分析两滑动表面在不同面积率和织构深度条件下的摩擦润滑性能。结果表明:织构表面摩擦因数随着面积率的增大而减小,承载力随着面积率的增大先增大后减小,在考虑摩擦性能与承载力的条件下,矩形-半球型复合型织构的面积率应控制在25%～36%之间;在确定合适的面积率的条件下,还应考虑不同的织构深度所产生的旋涡的影响。     

Effect of surface laser texture on friction properties of nickel-based composite

Laser surface texturing (LST) was performed on the nickel-based composites by a Nd:YAG pulsed laser and the regular-arranged dimples with diameter of 150 μm were fabricated on their surfaces. The textured surfaces were smeared with molybdenum disulfide powder. The tribological properties of the textured and filled composites were investigated by carrying out sliding wear tests against an alumina ball as a counterface using a high temperature ball-on-disk tribometer. The tests were conducted at a sliding speed of 0.4 m/s and at normal loads ranging from 20–100 N and from room temperature to 600 °C. The friction coefficient of nickel-based composite textured and smeared with molybdenum disulfide was found to reduce from 0.18 to 0.1 at the temperature range from 200 to 400 °C. The texture with a dimple density of 7.1% was observed to prolong wear life of MoS2 film by more than four times in comparison to the texture with other dimple densities. The lubricious oxide particles stored in the dimples reduce friction coefficient at elevated temperatures and compensate for the extra lubricant owing to the degradation of MoS₂ caused by its oxidation at high temperatures.     

磨料粒度对表面微织构纯钛干摩擦性能的影响

为了提高钛及钛合金钻具在超深钻探、深海钻探和外太空钻探工程中的减摩抗磨性能。利用激光表面加工技术在工业纯钛（TA2）表面制备了不同参数的点阵微织构。采用MS-T3000摩擦磨损试验机测试了微织构钛合金在不同粒度模拟月壤作用下的摩擦学性能。利用扫描电子显微镜和能谱分析仪分析磨痕形貌及元素含量。研究结果表明：当磨料粒度小于微织构点阵的直径时,磨料压入微织构点阵里,磨料具有滚动和滑动两种运动方式。当粒度大于微织构点阵的直径时,磨料不能完全压入微织构点阵里,磨料对微织构TA2表面产生了滑动犁削作用。由于两种磨料磨损的作用机理不同,同等条件下,小粒度的磨料作用下的微织构TA2的摩擦因数和磨损率较大粒度磨粒作用下的最大减少量分别为50%和53%。考虑磨料粒度与微结构的匹配性,可以大大降低摩擦减少磨损。